L2PNE-65/Q [MSYSTEM]
Power Transducer Series L-UNIT;
| 型号： | L2PNE-65/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Power Transducer Series L-UNIT |
| 文件： | 总3页 (文件大小：106K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: L2PNE
Power Transducer Series L-UNIT
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
PT TRANSDUCER
(dual; self-powered; RMS sensing)
Functions & Features
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• Converting an alternating voltage from a potential
(voltage) transformer into a standard process signal
• Minimum ripple
/C02: Polyurethane coating
• 2 transducers in one encolsure
• No auxiliary power source required
• Isolation up to 2000 V AC
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
• High-density mounting
GENERAL SPECIFICATIONS
Construction: Stand-alone; terminal access at the front
Connection: M3.5 screw terminals (torque 0.8 N·m)
Screw terminal: Nickel-plated steel (standard) or stainless
steel
Typical Applications
• Centralized monitoring and control of power line and
power supply voltages measured at switch boards
• Monitoring abnormal voltage drops for detecting overload
Housing material: Flame-resistant resin (black)
Isolation: Input to output, between channels
Input waveform: Up to 15 % of 3rd harmonic content
Overrange output: 60 – 120 % at 0 – 5 V
Span adjustment: 95 to 105 % (front)
75
(2.95)
75
(2.95)
INPUT SPECIFICATIONS
Frequency: 50 or 60 Hz
112
(4.41)
Input burden: 2 VA per channel
Overload capacity: 150 % of rating for 10 sec., 120 %
continuous
mm (inch)
MODEL: L2PNE–[1][2][3]
Operational range: 60 – 120 % of rating
ORDERING INFORMATION
• Code number: L2PNE–[1][2][3]
Specify a code from below for each [1] through [3].
(e.g. L2PNE-55/Q)
OUTPUT SPECIFICATIONS
■ OPERATION DIAGRAM
OUT %
100
• Specify the specification for option code /Q
(e.g. /C01/S01)
50
0
0
50 (60)
100
IN %
[1] INPUT
Voltage
Note: The described accuracy is not assured within 0 – 60%
of the rating, though output signal exists.
5: 0 – 150 V AC (used within 90 – 150 V)
6: 0 – 300 V AC (used within 180 – 300 V)
INSTALLATION
[2] OUTPUT
Current
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 85 %RH (non-condensing)
Mounting: Surface or DIN rail
G: 0 – 1 mA DC (Load resistance 5000 Ω max.)
Voltage
Weight: 300 g (0.66 lb)
3: 0 – 1 V DC (Load resistance 2000 Ω min.)
4: 0 – 10 V DC (Load resistance 20 kΩ min.)
5: 0 – 5 V DC (Load resistance 10 kΩ min.)
http://www.m-system.co.jp/
L2PNE SPECIFICATIONS
ES-1953 Rev.2 Page 1/3
MODEL: L2PNE
PERFORMANCE in percentage of span
Accuracy: ±0.5 % (at 23°C ±10°C or 73.4°F ±18°F,
45 – 65 Hz)
Response time: ≤ 2 sec. (0 – 100 % ±1 %)
Ripple: 1 %p-p max.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @ 1 minute
(input to output to ground, between channels)
Impulse withstand voltage: 1.2 / 50 μsec., ±5 kV
(input to output or ground)
CONNECTION DIAGRAM
Ch.1
VT
SOURCE
FUSE
U
V
u
v
+
–
1
2
11
12
Ch.1 OUTPUT
LOAD
SOURCE
FUSE
Ch.2
VT
U
V
u
v
+
–
5
6
15
16
Ch.2 OUTPUT
LOAD
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
8 (.31)
M3.5 SCREW
(Only on the used terminals)
2–5.8 (.23) dia. or
2–4.8 (.18) dia.
MTG HOLE
8 (.31) deep
DIN RAIL
35mm wide
1
9
2
3
4
5
6
7 8
TERMINAL
COVER
10 11 12 13 14 15 16
112 (4.41)
[3.3 (.13)]
75 (2.95)
•When mounting, no extra space is needed between units.
MOUNTING REQUIREMENTS unit: mm (inch)
■ M5 SCREWS
■ M4 SCREWS
60 (2.36)
60 (2.36)
2–M5
2–M4
http://www.m-system.co.jp/
L2PNE SPECIFICATIONS
ES-1953 Rev.2 Page 2/3
MODEL: L2PNE
Specifications are subject to change without notice.
http://www.m-system.co.jp/
L2PNE SPECIFICATIONS
ES-1953 Rev.2 Page 3/3
相关型号：
L2RJ302126MB80
Ceramic Capacitor, Multilayer, Ceramic, 200V, 20% +Tol, 20% -Tol, BR, 15% TC, 12uF, Surface Mount
KEMET
L2RL302126MB80
Ceramic Capacitor, Multilayer, Ceramic, 200V, 20% +Tol, 20% -Tol, BR, 15% TC, 12uF, Surface Mount
KEMET
©2020 ICPDF网 联系我们和版权申明