M2MNV-11-M2/Q [MSYSTEM]
Super-mini Signal Conditioners Mini-M Series;型号: | M2MNV-11-M2/Q |
厂家: | M-SYSTEM |
描述: | Super-mini Signal Conditioners Mini-M Series |
文件: | 总6页 (文件大小:134K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M2MNV
47 – 66 Hz)
DC Power
R: 24 V DC
Super-mini Signal Conditioners Mini-M Series
ANALOG SWITCHING MODULE
Functions & Features
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
R2: 11 – 27 V DC
• Switches between two analog signal channels
• Switches/Distributes one voltage signal to two channels
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
P: 110 V DC
Typical Applications
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
• Switching 1 – 5V DC signal: no contact failure that
happens when using mechanical contacts for this purpose
• Switching low-speed pulse signals
[4] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE
29.5 (1.16)
/CE: CE marking
Other Options
blank: none
Model
76
(2.99)
/Q: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
124
(4.88)
mm (inch)
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
MODEL: M2MNV-[1][2]-[3][4]
ORDERING INFORMATION
• Code number: M2MNV-[1][2]-[3][4]
Specify a code from below for each of [1] through [4].
(e.g. M2MNV-11-M2/CE/Q)
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
• Specify the specification for option code /Q
(e.g. /C01/S01)
Housing material: Flame-resistant resin (black)
Switching: Photo MOSFET relay
Note: Must be used with its socket. NOT installable to a
multi-unit installation base. (e.g. model: M2BS-16)
Isolation: Signal channel to switching command contact to
power
Power indicator LED: Green light turns on when the power is
supplied.
[1] SWITCHING CONTROL
1: Interlocking switching control (single-pole contact)
Status indicator LED 1: Green light turns on when the signal
channel 1 (A1-B1) is alive.
2: Independent switching control (double-pole contact)
Status indicator LED 2: Green light turns on when the signal
channel 2 (A2-B1) is alive.
[2] INPUT
1: Current signal (no receiving resistor)
2: Current signal (receiving resistor 50 Ω)
3: Voltage signal
INPUT & OUTPUT
■ Signal Channels
Max. operational voltage range: ±50 V DC (min. span 10
mV)
[3] POWER INPUT
AC Power
Max. operational current range: ±50 mA DC (min. span 1
mA)
M: 85 – 264 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
Max. operational frequency range: 100 Hz
Receiving resistor: 50 Ω incorporated (input code 2)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 1/6
http://www.m-system.co.jp/
MODEL: M2MNV
ON resistance: ≤ 50 Ω per wire
Signal channel to switching command contact: Basic
(ON resistance of photo MOSFET relay)
■ Output
insulation (300 V)
RoHS Directive
EN 50581
Current signal input (no receiving resistor):
Equal to the input signal
Current signal input (receiving resistor 50 Ω):
Voltage signal equal to [Current × 50 Ω]
Voltage signal input: Equal to the input signal
■ Switching Command: Relay or open collector
Contact detecting: 5 V DC / 1 mA
Detecting levels: ≤ 1 kΩ at ON / ≥ 10 kΩ at OFF
INSTALLATION
Power Consumption
•AC:
Approx. 3 VA at 100 V
Approx. 4 VA at 200 V
Approx. 5 VA at 264 V
•DC: Approx. 2 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 150 g (0.33 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.1 % (input code 2)
Temp. coefficient: ±0.010 %/°C (±0.006 %/°F) (input code
2)
Switching response time: ≤ 5 msec.
Leakage current at open circuit: ≤ 1 μA
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength:
2000 V AC @1 minute
(switching command contact to power to ground)
2000 V AC @1 minute
(signal channel to power to ground)
1500 V AC @1 minute
(signal channel to switching command contact)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Installation Category II
Pollution Degree 2
Signal channel or switching command contact to power:
Reinforced insulation (300 V)
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 2/6
http://www.m-system.co.jp/
MODEL: M2MNV
EXTERNAL VIEW
• Channel 1
Status LED 1
• Channel 2
Status LED 2
Power LED
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm
6 (.24)
DIN RAIL
35mm wide
3
2
5
1
4
6
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
9
8
7
11–M3
SCREW
11 10
21.5 (.85) 10 (.39)
84 (3.31)
114 (4.49)
22 (.87)
[4 (.16)]
29.5 (1.16)
• When mounting, no extra space is needed between units.
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 3/6
http://www.m-system.co.jp/
MODEL: M2MNV
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■ INTERLOCKING SWITCHING CONTROL (single-pole contact)
2
*
1
2
4
5
7
8
A1-1
A1-2
A2-1
A2-2
B1-1
B1-2
1
1
50
Ω
Ω
*
*
50
POWER STATUS STATUS
LED LED 1 LED 2
5V
5kΩ
Photo MOSFET
Relay Driver
10
11
3
6
9
U(+)
V(–)
POWER
SWITCHING
COMMAND
SW1
Base Socket
*1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω).
*2. Provided only with the input code 1: Current signal (no receiving resistor).
*1/*2 Not provided with the input code 3.
A1-B1 channel is connected when the SW1 is turned on (closed).
A2-B1 channel is connected when the SW1 is turned off (open).
■ INDEPENDENT SWITCHING CONTROL (double-pole contact)
2
*
1
2
4
5
7
8
A1-1
A1-2
A2-1
A2-2
B1-1
B1-2
1
1
50
Ω
Ω
*
*
50
POWER STATUS STATUS
LED LED 1 LED 2
5V
5V
5kΩ
5kΩ
Photo MOSFET
Relay Driver
10
11
3
U(+)
V(–)
POWER
SW1
SWITCHING
COMMAND
6
9
SW2
Base Socket
*1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω).
*2. Provided only with the input code 1: Current signal (no receiving resistor).
*1/*2 Not provided with the input code 3.
A1-B1 channel is connected when the SW1 is turned on (closed).
A2-B1 channel is connected when the SW2 is turned on (closed).
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 4/6
http://www.m-system.co.jp/
MODEL: M2MNV
SWITCHING OPERATIONS
■ INTERLOCKING SWITCHING CONTROL (single-pole contact)
Single contact is used to switch from Signal Channel 1 (A1 – B1) to Signal Channel 2 (A2 – B1) and vice versa.
CHANNEL 1 (A1)
CHANNEL 2 (A2)
Terminal 3 – 9 OFF (open)
Terminal 3 – 9 ON (closed)
OFF
ON
ON
OFF
Status LED turn on when the respective channels are alive.
• Switching Status
Current Signal (receiving resistor 50 Ω)
Voltage Signal
Current Signal (no receiving resistor)
*1
1
2
4
5
7
8
1
2
4
5
7
8
Power : OFF
Switching command : OFF (open)
*1
*1
*1
1
2
4
5
7
8
1
2
4
5
7
8
Power : ON
Switching command : OFF (open)
*1
*1
1
2
4
5
7
8
1
2
4
5
7
8
Power : ON
Switching command : ON (short)
*1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω).
Transition (ON to OFF, OFF to ON) Status
Current Signal (receiving resistor 50 Ω)
Voltage Signal
Current Signal (no receiving resistor)
*1
1
2
4
5
7
8
1
2
4
5
7
8
Power : ON
Switching command : OFF to ON
*1
or
Power : ON
Switching command : ON to OFF
When the switching command contact is switched from When the switching command contact is switched from
OFF to ON or from ON to OFF, the signal channel is OFF to ON or from ON to OFF, the signal channel is
switched only after all photo MOSFET relays turn on switched only after all photo MOSFET relays turn off
(closed).
(open).
*1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω).
■ INDEPENDENT SWITCHING CONTROL (double-pole contact)
Double contacts are used to independently switch Signal Channel 1 (A1 – B1) and Signal Channel 2 (A2 – B1).
CHANNEL 1 (A1)
CHANNEL 2 (A2)
Terminal 3 – 9 OFF (open)
Terminal 3 – 9 ON (closed)
Terminal 6 – 9 OFF (open)
Terminal 6 – 9 ON (closed)
OFF
ON
----
----
----
OFF
ON
----
Status LED turn on when the respective channels are alive.
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 5/6
http://www.m-system.co.jp/
MODEL: M2MNV
Specifications are subject to change without notice.
M2MNV SPECIFICATIONS
ES-5095 Rev.9 Page 6/6
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明