首页 |元器件品牌 | PCB在线计价/下单
首页 > M2SES2-B1-M/N

M2SES2-B1-M/N

更新时间：2024-10-29 22:47:17
品牌：MSYSTEM
描述：Super-mini Signal Conditioners Mini-M Series

PDF下载

中文翻译

PCB计价

M2SES2-B1-M/N 概述

Super-mini Signal Conditioners Mini-M Series

M2SES2-B1-M/N 数据手册

通过下载M2SES2-B1-M/N数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
MODEL: M2SES2  
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)  
Super-mini Signal Conditioners Mini-M Series  
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)  
Z: Specify current (See OUTPUT SPECIFICATIONS)  
Voltage  
HIGH/LOW SELECTOR  
(with simple loop test output)  
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)  
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)  
3: 0 – 1 V DC (Load resistance 1000 Ω min.)  
4: 0 – 10 V DC (Load resistance 10 kΩ min.)  
5: 0 – 5 V DC (Load resistance 5000 Ω min.)  
6: 1 – 5 V DC (Load resistance 5000 Ω min.)  
4W: -10 – +10 V DC (Load resistance 10 kΩ min.)  
5W: -5 – +5 V DC (Load resistance 5000 Ω min.)  
0: Specify voltage (See OUTPUT SPECIFICATIONS)  
Functions & Features  
• Monitors two DC input signals and transmitting an output  
signal proportional to the higher or lower input  
• Simple loop test output (0, 50, 100 %)  
• High-density mounting  
Typical Applications  
• Selecting greater flow, pressure, etc. for control  
• Heating control by multiple T/C’s on a furnace  
[3] POWER INPUT  
23 (.91)  
AC Power  
M: 85 – 264 V AC (Operational voltage range 85 – 264 V,  
47 – 66 Hz)  
Model  
76  
(2.99)  
STAT  
STAT  
2
1
(Select ‘/N’ for ‘Standards & Approvals’ code.)  
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,  
47 – 66 Hz)  
ZERO  
INP2  
SPAN  
ZERO  
INP1  
SPAN  
124  
(4.88)  
DC Power  
R: 24 V DC  
mm (inch)  
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)  
R2: 11 – 27 V DC  
MODEL: M2SES2–[1][2]–[3][4]  
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)  
(Select ‘/N’ for ‘Standards & Approvals’ code.)  
P: 110 V DC  
ORDERING INFORMATION  
• Code number: M2SES2-[1][2]-[3][4]  
Specify a code from below for each of [1] through [4].  
(e.g. M2SES2-AA-M2/CE/Q)  
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)  
[4] OPTIONS (multiple selections)  
Standards & Approvals (must be specified)  
/N: Without CE or UL  
• Special output range (For codes Z & 0)  
• Specify the specification for option code /Q  
(e.g. /C01/S01)  
/CE: CE marking  
Other Options  
blank: none  
[1] INPUT  
Current  
/Q: Option other than the above (specify the specification)  
A: 4 – 20 mA DC (Input resistance 250 Ω)  
B: 2 – 10 mA DC (Input resistance 500 Ω)  
C: 1 – 5 mA DC (Input resistance 1000 Ω)  
H: 10 – 50 mA DC (Input resistance 100 Ω)  
Voltage  
SPECIFICATIONS OF OPTION: Q (multiple selections)  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
/C02: Polyurethane coating  
6: 1 – 5 V DC (Input resistance 1 MΩ min.)  
/C03: Rubber coating  
TERMINAL SCREW MATERIAL  
/S01: Stainless steel  
[2] OUTPUT  
Current  
A: 4 – 20 mA DC (Load resistance 750 Ω max.)  
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)  
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)  
D: 0 – 20 mA DC (Load resistance 750 Ω max.)  
E: 0 – 16 mA DC (Load resistance 900 Ω max.)  
M2SES2 SPECIFICATIONS  
ES-5098 Rev.6 Page 1/3  
http://www.m-system.co.jp/  
MODEL: M2SES2  
to power to ground)  
GENERAL SPECIFICATIONS  
Construction: Plug-in  
Connection: M3 screw terminals (torque 0.8 N·m)  
Screw terminal: Chromated steel (standard) or stainless  
steel  
STANDARDS & APPROVALS  
EU conformity:  
EMC Directive  
Housing material: Flame-resistant resin (black)  
Isolation: Input to output to power  
EMI EN 61000-6-4  
EMS EN 61000-6-2  
Overrange output: Approx. -10 to +120 % at 1 – 5 V  
Input zero adjustments: -2 to +2 % (front)  
Input span adjustments: 98 to 102 % (front)  
DIP switch setting: Selecting output options  
Status indicator LED 1: Green LED; indicates the  
transmitter’s function mode (Refer to the instruction  
manual.)  
Low Voltage Directive  
EN 61010-1  
Installation Category II  
Pollution Degree 2  
Input or output to power: Reinforced insulation (300 V)  
Input to output: Basic insulation (300 V)  
RoHS Directive  
Status indicator LED 2: Orange LED; indicates the  
transmitter’s function mode (Refer to the instruction  
manual.)  
EN 50581  
INPUT SPECIFICATIONS  
■ DC Current: Input resistor incorporated  
OUTPUT SPECIFICATIONS  
■ DC Current: 0 – 20 mA DC  
Minimum span: 1 mA  
Offset: Max. 1.5 times span  
Load resistance: Output drive 15 V max.  
■ DC Voltage: -10 – +12 V DC  
Minimum span: 5 mV  
Offset: Max. 1.5 times span  
Load resistance: Output drive 1 mA max.; at ≥ 0.5 V  
INSTALLATION  
Power Consumption  
•AC:  
Approx. 3 VA at 100 V  
Approx. 4 VA at 200 V  
Approx. 5 VA at 264 V  
•DC: Approx. 3 W  
Operating temperature: -5 to +55°C (23 to 131°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Mounting: Surface or DIN rail  
Weight: 150 g (0.33 lb)  
PERFORMANCE in percentage of span  
Accuracy: ±0.2 %  
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)  
Response time: ≤ 0.5 sec. (0 – 90 %)  
Line voltage effect: ±0.1 % over voltage range  
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 2000 V AC @1 minute (input to output  
M2SES2 SPECIFICATIONS  
ES-5098 Rev.6 Page 2/3  
http://www.m-system.co.jp/  
MODEL: M2SES2  
EXTERNAL VIEW  
■ FRONT VIEW  
■ SIDE VIEW  
Status Indicator LED2  
Output Function  
Setting  
Status Indicator LED1  
SW1  
1 2 3 4  
ON  
Zero Adj. (ZERO2)  
OFF  
Input 2  
Span Adj. (SPAN2)  
Zero Adj. (ZERO1)  
Input 1  
Span Adj. (SPAN1)  
Refer to the instruction manual for detailed procedures.  
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm  
6 (.23)  
DIN RAIL  
35mm wide  
4
1
5
8
2–4.2x5  
(.17x.20)  
MTG HOLE  
6 (.24) deep  
12  
9
8–M3  
SCREW  
14 13  
21.5 (.85) 10 (.39)  
84 (3.31)  
114 (4.49)  
15 (.59)  
[4 (.16)]  
23 (.91)  
• When mounting, no extra space is needed between units.  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
STATUS  
Z
S
Z
S
Isolation  
Output  
Driver  
+
–
+
–
1
4
5
8
9
+
Selector  
*
*
INPUT 1  
INPUT 2  
OUTPUT  
POWER  
12  
13  
14  
–
DIP SWITCH  
U(+)  
V(–)  
Base Socket  
*Input shunt resistor incorporated for current inputs.  
Specifications are subject to change without notice.  
M2SES2 SPECIFICATIONS  
ES-5098 Rev.6 Page 3/3  
http://www.m-system.co.jp/  

M2SES2-B1-M/N 相关器件

型号 制造商 描述 价格 文档
M2SES2-B1-M/Q MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-M2 MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-M2/CE MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-M2/N MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-M2/Q MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-P MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-P/CE MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-P/N MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-P/Q MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格
M2SES2-B1-R MSYSTEM Super-mini Signal Conditioners Mini-M Series 获取价格

M2SES2-B1-M/N 相关文章

  • HARTING(浩亭)圆形连接器产品选型手册
    2024-10-31
    6
  • HYCON(宏康科技)产品选型手册
    2024-10-31
    6
  • GREEGOO整流二极管和晶闸管产品选型手册
    2024-10-31
    7
  • 西门子豪掷106亿美元，战略收购工程软件巨头Altair
    2024-10-31
    8

    • 热门型号

  • LM358
  • UPC8158
  • XC6105A618
  • 2N5087/D28Z
  • TMM-136-06-S-S-SM-23-P
  • NC7WZ16P6X
  • SDR10KSM
  • STC53K33N07
  • ERG3SG242
  • M2XRP2-J1Z1-R
  • TMM-139-01-G-S-SM
  • 54F20
  • TMP513
  • SZ6A11
  • PEL12S
  • 概述
  • 数据手册
    • 2024 ICPDF网 联系我们和版权申明:QQ 272164286