M2XRP2-J1V2-P/N [MSYSTEM]

Super-mini Signal Conditioners Mini-M Series;


型号：	M2XRP2-J1V2-P/N
厂家：	M-SYSTEM
描述：	Super-mini Signal Conditioners Mini-M Series
文件：	总6页 (文件大小：141K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M2XRP2

Super-mini Signal Conditioners Mini-M Series

[1] INPUT

0: User-calibrated (Factory default: open collector, 0 – 100 kHz)

ENCODER SPEED TRANSMITTER

(PC programmable; built-in excitation)

Functions & Features

If the unit is to be factory-calibrated to a specific

input type, please select from the following:

A: Open collector

• Converts a two-phase forward and reverse rotation

pulse signal with 90 degree phase difference into a forward

and reverse speed signal

B: Voltage pulse

J: RS-422 line driver pulse

• Built-in excitation

• PC programmable input and output ranges

• Input pulse monitoring LED

[2] EXCITATION

0: User-calibrated (Factory default: 12 V DC / 5 mA)

• Direct RS-422 input

If the unit is to be factory-calibrated to a specific

voltage value, please select from the following:

1: 5 V DC / 5 mA

Typical Applications

• Measuring moving speed of a machine with a rotary

encoder

4: 12 V DC / 5 mA

[3] OUTPUT

29.5 (1.16)

0: User-calibrated (Factory default: 4 – 20 mA)

If the unit is to be factory-calibrated to a specific

output type, please select from the following:

Current

(2.99)

Z1: Range 0 – 20 mA DC

124

(4.88)

Voltage

V1: Range -2.5 – +2.5 V DC

mm (inch)

V2: Range -10 – +10 V DC

(Configurator software is used to change output over the

described range of the selected suffix code. For changing

out of this range, set the Output Range Selectors inside the

unit before software adjustment.)

MODEL: M2XRP2-[1][2][3]-[4][5]

ORDERING INFORMATION

• Code number: M2XRP2-[1][2][3]-[4][5]

[4] POWER INPUT

AC Power

Specify a code from below for each [1] through [5].

(e.g. M2XRP2-000-M2/CE/Q)

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

• Specify the specification for option code /Q

(e.g. /C01/S01)

47 – 66 Hz)

(90 – 264 V for UL)

• Non-specified orders will be shipped at default factory

settings (M2XRP2-000: Open collector input/12 V

excitation/4 – 20 mA output). However, a power suffix code

must be specified.

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

P: 110 V DC

If you specify a full code number without specific calibration

ranges, the input frequency is factory set to the maximum

range available for the selected input code and the output is

set to the default range. Use Ordering Information Sheet

(No. ESU-5059).

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

(110 V ±10 % for UL)

Note: Must be used with its socket. NOT installable to a

multi-unit installation base. (e.g. model: M2BS-16)

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 1/6

MODEL: M2XRP2

RS-232-C level

[5] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE or UL

Pulse sensing: DC coupled or capacitor coupled selectable

with DIP SW

Low-end cutout: 100 msec. – 100 sec. or no cutout

programmable

/CE: CE marking

/UL: UL approval, CE marking

Other Options

blank: none

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; 20 mA max. at

shortcircuit

/Q: Option other than the above (specify the specification)

Maximum frequency: 200 kHz

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

Frequency ranges:

0 – 10 mHz, 0 – 100 mHz, 0 – 1 Hz, 0 – 10 Hz, 0 – 100 Hz,

0 – 1 kHz, 0 – 10 kHz, 0 – 100 kHz

(Choose 100 kHz range to set the zero/span frequencies

lower than -100 kHz (higher than 100 kHz in the reverse

direction) or higher than 100 kHz (higher than 100 kHz in

the forward direction.))

/C02: Polyurethane coating

/C03: Rubber coating (UL not available)

TERMINAL SCREW MATERIAL

/S01: Stainless steel (UL not available)

Minimum pulse width time requirement: 2.5 μsec.

Minimum span: 10 % of the selected frequency range

Noise filter: See table 2

RELATED PRODUCTS

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

■ Open Collector

Input requirements

EXCITATION

5 V

SENSING

OFF

Approx. 5 V

Approx. 10 V

≥200 kΩ

≤200 Ω

12 V

Amplitude: 5 - 12 V

Detecting level:

GENERAL SPECIFICATIONS

Construction: Plug-in

5 V excitation: 1 V

12 V excitation: 2 V

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

(Detecting voltage in the internal circuit.

For open collector input, be sure to re-adjust the voltage

back to 1 V (5 V excitation) or 2 V (12 V excitation) if it has

been changed for other input types.)

Detecting pulse edge: OFF to ON

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -15 to +115 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Configuration: Via PC Configurator Software (model:JXCON)

on the Windows PC connected to

the front jack.

If not specified, the input range is 0 Hz – 1 kHz.

■ Voltage Pulse

Waveform: Square or sine

Input impedance: 10 kΩ min.

Pulse amplitude: 0.1 – 30 Vp-p

Pulse amplitude Range: See table 1.

Max. voltage between input terminals: See table 1.

Sensitivity Scale: See table 1.

Programmable features include:

· I/O type and range

· Zero and span adjustments

Detecting level: -2 – +4 V

· Low-end cutout

Detecting pulse state: A pulse rise detected when the input

voltage goes above the detecting level;

a pulse sink detected when it goes below the level.

If not specified, the input range is 0 Hz – 1 kHz.

■ RS-422 Line Driver Pulse

· Linearization

Status indicator LED: Red LED; Flashing patterns indicate

different operating status of the transmitter.

Input monitor (PL1): Green LED blinks according to the input

phase A.

Receiver: Conforms to RS-422

Input monitor (PL2): Green LED blinks according to the input

phase B.

If not specified, the input range is 0 Hz – 1 kHz.

Excitation adjustment: 5V or 12V DC

Configurator connection: 2.5 dia. miniature jack;

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 2/6

MODEL: M2XRP2

[Table 1]

If not specified, the output range is shown below.

SENSITIVITY

SCALE

MAX.INPUT

VOLTAGE

PULSE AMPLITUDE

RANGE

V1: 0 – 1 V DC

V2: 1 – 5 V DC

10 – 30 Vp-p

5 – 10 Vp-p

1 – 5 Vp-p

30 V

10 V

5 V

1/6

1/2

INSTALLATION

Power Consumption

0.1 – 1 Vp-p*

1 V

*Input frequency within 50 kHz

•AC:

When the parameters have been set with DIP switches and the

PC Configurator Software (model: JXCON), a specific sensitivity

scale is applied according to the pulse amplitude setting. The

scaled input voltage is then compared to the preset detecting

level (-2.00 to +4.00 V).

Approx. 4 VA at 100 V

Approx. 5 VA at 200 V

Approx. 6 VA at 264 V

With DC coupling, the scaled maximum voltage must be higher

than the detecting level and the minimum voltage must be lower

than that so that the pulse state is accurately detected. (Refer to

the instruction manual for detailed information about adjusting the

detecting level.)

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

[Table 2]

FREQUENCY RANGE

0 – 10 mHz

0 – 100 mHz

0 – 1 Hz

NOISE FILTER TYPE

With

W/O

PERFORMANCE

Accuracy: Input accuracy + output accuracy

Input accuracy: ≤ ±0.03% of the selected freq. range

Output accuracy: ≤ ±0.03% of the selected output range

The input accuracy is inversely proportional to the input

span; while the output accuracy is likewise inversely

proportional to the output span. With [Input Range / Input

Span] ≤ 1, the input accuracy is fixed at ±0.03%.

See CALCULATION EXAMPLES OF OVERALL ACCURACY.

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of I/O range

at -5 to +55°C [23 to 131°F]

0 – 10 Hz

0 – 100 Hz

0 – 1 kHz

0 – 10 kHz

0 – 100 kHz

Be sure to apply the noise filter appropriate for the selected

frequency range as shown in the table above. The accuracy

may not be assured if no filter is applied.

OUTPUT SPECIFICATIONS

■ DC Current

Response time: 0.5 sec. + 1 pulse cycle (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

Output range: 0 – 20 mA DC

Conformance range: 0 – 23mA DC

Minimum span: 1 mA

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

maintained.

CALCULATION EXAMPLES OF OVERALL ACCURACY

[Example] Open collector input, 0 – 50 kHz; 1 – 5 V output.

Selected freq. range (100 kHz) ÷ Input span (50 kHz)×

Accuracy (0.03 %)= 0.06 % (Input accuracy)

Load resistance: Output drive 12 V max.

(e.g. 4 – 20 mA: 600 Ω [12 V ÷ 20 mA])

If not specified, the output range is 4 – 20 mA DC.

■ DC Voltage

Selected output range (20 V) ÷ Output span (4 V) ×

Accuracy (0.03 %)= 0.15 % (Output accuracy)

Code V1 (narrow spans)

Conformance range: -3 – +3 V DC

Output range: -2.5 – +2.5 V DC

Minimum span: 250 mV

Overall accuracy = 0.06 + 0.15 = ±0.21 %

Code V2 (wide spans)

Conformance range: -11.5 – +11.5 V DC

Output range: -10 – +10 V DC

Minimum span: 1 V

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

maintained.

Load resistance: Output drive 1 mA max.

(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 3/6

MODEL: M2XRP2

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581

Approval:

UL/C-UL nonincendive Class I, Division 2,

Groups A, B, C, and D

(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)

UL/C-UL general safety requirements

(UL 61010-1, CAN/CSA-C22.2 No.61010-1)

EXTERNAL VIEW

Input Selector SW

■ FRONT VIEW (with cover open)

■ LEFT SIDE VIEW (with cover removed)

Configurator Jack

ON OFF ON OFF

OFF

Input Monitor LED, PL1

SW1

SW2

SW3

Input Monitor LED, PL2

Status Indicator LED

Zero/Span Selector

Top: SPAN

Middle: OFF

Bottom: ZERO

Output Selector SW

ON OFF

UP/DOWN Switches

The front cover cannot be opened to 180 deg.

when flush with neighboring units.

SW4

Refer to the instruction manual for detailed procedures.

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 4/6

MODEL: M2XRP2

OPERATION

20mA

+10V

4mA

rev. 30 Hz

–10V

fwd. 100 Hz

CUTOUT

rev. 100 Hz

fwd. 100 Hz

REVERSE

STOP

FORWARD

INPUT

ACCEL.

DECEL.

0 Hz

ACCEL.

CUTOUT

–

Forward Rotation: Phase A leads the Phase B by 90 degrees.

Reverse Rotation: Phase A lags behind Phase B by 90 degrees.

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

6 (.23)

DIN RAIL

35mm wide

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

11–M3

SCREW

11 10

21.5 (.85) 7.3 (.29)

86.7 (3.41)

116.7 (4.59)

22 (.87)

[4 (.16)]

29.5 (1.16)

• When mounting, no extra space is needed between units.

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 5/6

MODEL: M2XRP2

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

■ OPEN COLLECTOR, VOLTAGE INPUT

INPUT

MON. PL1

STATUS

MON.

ZERO/SPAN

SELECTOR

INPUT TYPE

SELECTOR

ROTARY

ENCODER

Isolation

Waveform

Shaper

Digital

Computation

Output

Driver

–

OUTPUT

POWER

–

COM

UP/DOWN

SWITCHES

Waveform

Shaper

U(+)

V(–)

Exc.

Supply

PWR

INPUT

MON. PL2

JACK

CONFIGURATOR

Base Socket

Remark: The sensor excitation voltage is supplied also across the terminals 3 – 6.

■ RS-422 LINE DRIVER INPUT

STATUS MON.

ROTARY

ENCODER

ZERO/SPAN

SELECTOR

–

COM

INPUT

MON. PL1

Isolation

RS-422

Receiver

Digital

Computation

Output

Driver

INPUT

MON. PL2

OUTPUT

POWER

–

RS-422

Receiver

UP/DOWN

SWITCHES

U(+)

V(–)

Excitation

Supply

PWR

JACK

CONFIGURATOR

Base Socket

Specifications are subject to change without notice.

http://www.m-system.co.jp/

M2XRP2 SPECIFICATIONS

ES-5059 Rev.12 Page 6/6

M2XRP2-J1V2-P/N [MSYSTEM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB