M2XV2-S2V2-P/N [MSYSTEM]
Super-mini Signal Conditioners Mini-M Series;型号: | M2XV2-S2V2-P/N |
厂家: | M-SYSTEM |
描述: | Super-mini Signal Conditioners Mini-M Series |
文件: | 总4页 (文件大小:118K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M2XV2
Super-mini Signal Conditioners Mini-M Series
[2] OUTPUT
Current
Z1: Range 0 – 20 mA DC
Voltage
SIGNAL TRANSMITTER
(PC programmable)
V1: Range -2.5 – +2.5 V DC
V2: Range -10 – +10 V DC
Functions & Features
• Converts DC input from a sensor into a standard process
signal
(Configurator software is used to change output over the
described range of the selected suffix code. For changing
out of this range, set the Output Range Selectors inside the
unit before software adjustment.)
• PC programmable
Typical Applications
• Isolation between control room and field instrumentation
• Ideal for quick spare part
[3] POWER INPUT
AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
23 (.91)
47 – 66 Hz)
(90 – 264 V for UL)
DC Power
M
od
el
76
(2.99)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
P: 110 V DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(110 V ±10 % for UL)
124
(4.88)
mm (inch)
[4] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
MODEL: M2XV2–[1][2]–[3][4]
/CE: CE marking
/UL: UL approval, CE marking
Other Options
ORDERING INFORMATION
• Code number: M2XV2-[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. M2XV2-S2Z1-R/CE/Q)
blank: none
/Q: Option other than the above (specify the specification)
• Input range (e.g. 1 – 5 V DC)
• Output range (e.g. 4 – 20 mA DC)
Specify the specification for option code /Q
(e.g. /C01/S01)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
TERMINAL SCREW MATERIAL
[1] INPUT
Current
/S01: Stainless steel (UL not available)
Z1: Range 0 – 50 mA DC (Input resistance 100 Ω)
Voltage
S1: Range -1 – +1 V DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
(Configurator software is used to change input over the
described range of the selected suffix code. For changing
out of this range (between S1 and S2), set the Input Range
Selector on the side of unit before software adjustment.
For a current input, set the Selector to the same setting as
for S2 and use a receiving resistor.)
RELATED PRODUCTS
• PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
M2XV2 SPECIFICATIONS
ES-5081 Rev.9 Page 1/4
http://www.m-system.co.jp/
MODEL: M2XV2
maintained.
GENERAL SPECIFICATIONS
Construction: Plug-in
Load resistance: Output drive 15 V max.
(e.g. 4 – 20 mA: 750 Ω [15 V ÷ 20 mA])
If not specified, the output range is 4 – 20 mA DC.
■ DC Voltage
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
Code V1 (narrow spans)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -15 to +115 %
(Negative current output is not provided.)
Manual zero adjustments: -5 to +5 %
(factory setting: 0 %)
Operational range: -3 – +3 V DC
Output range: -2.5 – +2.5 V DC
Minimum span: 250 mV
Code V2 (wide spans)
Operational range: -11.5 – +11.5 V DC
Output range: -10 – +10 V DC
Minimum span: 1 V
Manual span adjustments: 95 to 105 %
(factory setting: 100 %)
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Programming: Downloaded from PC; input range, output
range, zero and span, simulating output, etc.
Status indicator LED: Blinking patterns indicate different
operating status of the transmitter.
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
Load resistance: Output drive 1 mA max.
(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])
If not specified, the output range is shown below.
V1: 0 – 1 V DC
V2: 1 – 5 V DC
INPUT SPECIFICATIONS
■ DC Current: Shunt resistor attached to the input terminals
(0.5 W)
INSTALLATION
Power Consumption
Operational range: 0 – 70 mA DC with 100 Ω, 0.5 W
Input range: 0 – 50 mA DC
•AC:
Approx. 3 VA at 100 V
Minimum span: 2 mA
Approx. 4 VA at 200 V
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is 4 – 20 mA DC.
■ DC Voltage
Approx. 5 VA at 264 V
•DC: Approx. 2 W
Operating temperature: -30 to +60°C (-22 to +140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 120 g (0.26 lb)
Code S1 (narrow spans)
Operational range: -1.15 – +1.15 V DC
Input range: -1 – +1 V DC
Minimum span: 10 mV
Code S2 (wide spans)
PERFORMANCE in percentage of span
Accuracy: Input accuracy + output accuracy
Inversely proportional to the span.
Operational range: -11.5 – +11.5 V DC
Input range: -10 – +10 V DC
Minimum span: 100 mV
Except the accuracy of input resistor.
Input accuracy: (% of max. input range)
-1 – +1 V : ±0.01 %
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is shown below.
S1: 0 – 100 mV DC
-10 – +10 V : ±0.01 %
0 – 50 mA : ±0.02 %
S2: 1 – 5 V DC
Output accuracy: ±0.04 % of max. output range
See CALCULATION EXAMPLES OF OVERALL ACURACY.
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span
at -5 to +55°C [23 to 131°F]
OUTPUT SPECIFICATIONS
■ DC Current
Response time: ≤ 0.9 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
Operational range: 0 – 24 mA DC
Output range: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
M2XV2 SPECIFICATIONS
ES-5081 Rev.9 Page 2/4
http://www.m-system.co.jp/
MODEL: M2XV2
CALCULATION EXAMPLES OF OVERALL ACCURACY
[Example] Input Type -10 – +10 V, Input Range 1 – 5 V,
Output Type 0 – 20 mA, Output Range 4 – 20 mA
Max. Input Range (20 V) ÷ Span (4 V) × 0.01 % = 0.05 %
Max. Output Range (20 mA) ÷ Span (16 mA) × 0.04 %
= 0.05 %
Overall accuracy = 0.05 + 0.05 = ±0.10 %
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Installation Category II
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
RoHS Directive
EN 50581
Approval:
UL/C-UL nonincendive Class I, Division 2,
Groups A, B, C, and D
(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)
UL/C-UL general safety requirements
(UL 61010-1, CAN/CSA-C22.2 No.61010-1)
EXTERNAL VIEW
■ FRONT VIEW (with cover open)
■ RIGHT SIDE VIEW
Configurator Jack
Input Range Selector
Status Indicator LED
Zero/Span Selector
Position L : code S1
Position H: code S2, Z1
Top: SPAN
Middle: OFF
Bottom: ZERO
ATT
[e.g.]
Output code V1
V
I
UP/DOWN Switches
SW3
SW6
SW2
The front cover cannot be turned open by 180 deg.
when there is no extra space between units.
8
■ LEFT SIDE VIEW
(with cover removed)
7
6
5
4
3
2
1
V
I
N
O
SW7
SW4
Output Range Selectors
Refer to the instruction manual for detailed procedures.
M2XV2 SPECIFICATIONS
ES-5081 Rev.9 Page 3/4
http://www.m-system.co.jp/
MODEL: M2XV2
EXTERNAL DIMENSIONS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
4
1
5
8
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
12
9
8–M3
SCREW
14 13
21.5 (.85) 7.3 (.29)
86.7 (3.41)
116.7 (4.59)
15 (.59)
[4 (.16)]
23 (.91)
• When mounting, no extra space is needed between units.
TERMINAL ASSIGNMENTS unit: mm (inch)
INPUT RESISTOR
(model: REM2)
4
1
5
8
12
9
14 13
Input shunt resistor attached
for current input.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
STATUS
INPUT RANGE
SELECTOR
ZERO/SPAN
SELECTOR
OUTPUT RANGE
SELECTORS
Isolation
Digital
Computation
Output
Driver
+
–
1
9
+
Low Drift
Amplifier
*
INPUT
R
OUTPUT
POWER
4
12
13
14
–
UP/DOWN
SWITCHES
5
U(+)
V(–)
8
JACK
CONFIGURATOR
Base Socket
*Input shunt resistor attached for current input.
Specifications are subject to change without notice.
M2XV2 SPECIFICATIONS
ES-5081 Rev.9 Page 4/4
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明