M6NXAP-S1A-R/Q [MSYSTEM]
Screw Terminal Ultra-Slim Signal Conditioners M6N Series;型号: | M6NXAP-S1A-R/Q |
厂家: | M-SYSTEM |
描述: | Screw Terminal Ultra-Slim Signal Conditioners M6N Series |
文件: | 总4页 (文件大小:149K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M6NXAP
Output modulation type and range are configurable with the
configure software. The output signal type is configurable
with the DIP switches.
Screw Terminal Ultra-Slim Signal Conditioners M6N Series
DC/FREQUENCY CONVERTER
(PC programmable)
POWER INPUT
Function & features
DC Power
• 7.5-mm wide ultra-slim design
• Low profile allows the M6N module mounted in a 120-mm
deep panel
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
• Converts a DC input into a FM (frequency modulation) or
PWM (pulse width modulated) signal
• PC programmable
[3] OPTIONS
blank: none
• High-density mounting
/Q: With options (specify the specification)
• Power and status indicator LEDs
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
7.5 (.30)
/C02: Polyurethane coating
EX-FACTORY SETTING
102
(4.02)
/SET: Preset according to the Ordering Information Sheet
(No. ESU-7837)
RELATED PRODUCTS
102
• PC configurator software (model: M6CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
(4.02)
mm (inch)
MODEL: M6NXAP–[1][2]–R[3]
ORDERING INFORMATION
• Code number: M6NXAP-[1][2]-R[3]
Specify a code from below each [1] through [3].
(e.g. M6NXAP-Z1A-R/Q)
GENERAL SPECIFICATIONS
Connection
Input and output: M3 screw terminal (torque 0.5 N·m)
Power input: Via the Installation Base (model: M6NBS)
or M3 screw terminal (torque 0.5 N·m)
Recommended solderless terminal: Max. 5.8 mm (0.23”)
wide; Ones with insulation sleeve do not fit.
• Specify the specification for option code /Q
(e.g. /C01/SET)
[1] INPUT
Applicable wire size: 0.2 – 2.5 mm
2
Current
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Z1: Range 0 – 50 mA DC (Input resistance 25 Ω)
Voltage
S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.)
S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)
(Configurator software is used to change the input type and
precise range.)
Zero adjustment: -2 to +2 % (PC programming)
Span adjustment: 98 to 102 % (PC programming)
Power LED: Green light turns on when the power is supplied.
Status indicator LED: Orange LED; Blinking patterns indicate
different operating status of the transmitter.
Programming: Downloaded from PC
• Input type and range
[2] OUTPUT
A: Open collector (100 kHz for FM, 1 kHz for PWM)
M: 5 V pulse (100 kHz for FM, 1 kHz for PWM)
N: 12 V pulse (100 kHz for FM, 1 kHz for PWM)
P: 24 V pulse (100 kHz for FM, 1 kHz for PWM)
• Modulation type (FM, PWM)
• Output range
• Zero and span
M6NXAP SPECIFICATIONS
ES-7926 Rev.4 Page 1/4
http://www.m-system.co.jp/
MODEL: M6NXAP
• User’s linearization table (max. 101 points, specified
within -2 to +102 %)
Maximum frequency: 100 kHz
Saturation voltage: 0.5 V DC
(Factory default: 0 to 10 kHz, frequency modulation)
■ Voltage Pulse
• Others
(Refer to the instruction manual for details)
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
High level: Rating (5, 12 or 24 V) ±10 %
Low level: ≤ 0.5 V
■Recommended solderless terminal (unit: mm (inch))
Load resistance:
• ≥ 1.0 kΩ for 5 V
5.5 max.
(.22)
4 min.
(.16)
• ≥ 2.4 kΩ for 12 V
3.2 (.13) dia.
• ≥ 4.8 kΩ for 24 V
Factory default: 0 to 10 kHz, Frequency modulation
INSTALLATION
Power consumption: Approx. 1 W
INPUT SPECIFICATIONS
■ DC Current: Input resistor incoporated
(If not specified, the input range is 4 – 20 mA DC.)
Input range: 0 – 50 mA DC
Operating temperature: -20 to +55°C (-4 to +131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Installation Base (model: M6NBS) or DIN rail
Weight: 65 g (2.3 oz)
Minimum span: 2 mA
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
■ DC Voltage
PERFORMANCE in percentage of span
Accuracy: Input accuracy + output accuracy
Inversely proportional to the span.
•Code S1 (narrow spans)
Input accuracy in percentage of input span:
• ±0.01 % for -1000 to +1000 mV
Input range: -1000 – +1000 mV DC
Minimum span: 100 mV
• ±0.01 % for -10 to +10 V
•Code S2 (wide spans)
• ±0.02 % for 0 to 50 mA
Input range: -10 – +10 V DC
Output accuracy at max. frequency (FM):
• ±0.10 % for ≤ 10 kHz
Minimum span: 1 V
Offset: Lower range can be any specific value within the
input range provided that the minimum span is maintained.
If not specified, the input range is shown below.
S1: 0 – 100 mV DC
• ±0.05 % for ≤ 5 kHz
• ±0.02 % for ≤ 1 kHz
• For 10 kHz to 100 kHz output accuracy is following.
Output accuracy (%) = Max. frequency (kHz) x 0.01
Output accuracy (PWM): ±0.2 %
S2: 1 – 5 V DC
See CALCULATION EXAMPLES OF OVERALL ACCURACY.
Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. input
span
OUTPUT SPECIFICATIONS
■ Modulation
• Frequency modulation
Response time: 0.1 sec. + 1 pulse cycle of 100 % output
The time between the moment when the input changes 0 %
to 100 % and the moment when the first pulse changes.
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
Output range: 0 to 100 %
Max. frequency: 100 kHz
Min. span: 0.01 Hz
(The output frequency changes according to the input
signal. Duty rate is approx. 50 %)
• Pulse width modulation
Output range: 1 to 99 %
Usable frequency: 0.008 Hz to 1 kHz
(According to the input signal, the output pulse width (duty
rate) changes without change of its frequency. The
frequency is configurable with PC Configurator software,
M6CFG.).
CALCULATION EXAMPLES OF OVERALL ACCURACY
1. Frequency modulation
E.g.: Input range -10 to +10 V, input span 1 to 5 V, max.
frequency 10 kHz
Input accuracy = Input range (20 V) ÷ Input span (4 V) x
Input accuracy (0.01 %) = 0.05 %
■ Open Collector
50 V DC @ 100 mA (resistive load)
Output accuracy = 0.10 %
M6NXAP SPECIFICATIONS
ES-7926 Rev.4 Page 2/4
http://www.m-system.co.jp/
MODEL: M6NXAP
Overall accuracy = ±0.15 %
2. Pulse width modulation
E.g.: Input range -10 to +10 V, input span 1 to 5 V,
frequency 1 kHz
Input accuracy = 0.05 % (same as above)
Output accuracy = 0.20 %
Overall accuracy = ±0.25 %
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
EXTERNAL VIEW
FRONT VIEW (with the cover open)
SIDE VIEW
5
6
7
8
Power LED
Status Indicator LED
Configurator Jack
Output Range Selectors
1
2
3
4
The output signal type is configurable with the DIP switches. Refer to the installation manual for detailed procedure.
M6NXAP SPECIFICATIONS
ES-7926 Rev.4 Page 3/4
http://www.m-system.co.jp/
MODEL: M6NXAP
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
SCREWDRIVER
INSERTION ANGLE
: approx. 55°
*
WIRE INSERTION ANGLE
: approx. 35°
8–M3
SCREW TERMINAL
DIN RAIL HOOK
5
6
7
8
DIN RAIL
35mm wide
1
2
3
4
[1 (.04)]
SCREWDRIVER
INSERTION ANGLE
: approx. 40°
7.5 (.30)
102 (4.02)
*Screwdriver stem diameter: 6 mm (.24”) or less
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
STATUS
IND. LED
Isolation
DIP SW
25 Ω
+
Digital
Computation
Output
Driver
+
1
5
6
CURRENT
(Z1)
OUTPUT
POWER
Low Drift
Amplifier
–
–
2
–
VOLTAGE
(S1, S2)
POWER LED
3
+
+
–
7
8
4
CONFIGURATOR
JACK
POWER
Output Connection Examples
■ Open Collector
■ Voltage Pulse
5
6
+
–
+
–
5
6
+
+
–
–
Specifications are subject to change without notice.
M6NXAP SPECIFICATIONS
ES-7926 Rev.4 Page 4/4
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明