首页 > PHSH-C2S

PHSH-C2S

更新时间：2024-10-29 22:47:32

品牌：MSYSTEM

描述：Plug-in Signal Conditioners M-UNIT

PDF下载

中文翻译

PCB计价

概述
数据手册

如果您发现信息不准确，欢迎纠错

PHSH-C2S 概述

Plug-in Signal Conditioners M-UNIT

PHSH-C2S 数据手册

通过下载PHSH-C2S数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载

MODEL: PHS

G: 0 – 1 mA DC (Input resistance 1000 Ω)

Plug-in Signal Conditioners M-UNIT

H: 10 – 50 mA DC (Input resistance 100 Ω)

J: 0 – 10 μA DC (Input resistance 1000 Ω)

K: 0 – 100 μA DC (Input resistance 1000 Ω)

GW: -1 – +1 mA DC (Input resistance 1000 Ω)

FW: -10 – +10 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

PEAK HOLD

(isolated)

Functions & Features

• Track mode: the output follows proportionally to the input

• Peak-hold mode: responds only to an increasing signal,

holding the maximum value until a higher signal or a

command to reset is received

• Minimum value (valley) hold selectable

• LCD meter

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

15: 0 – 50 mV DC (Input resistance 10 kΩ min.)

16: 0 – 60 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

5W: -5 – +5 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

• High-density mounting

Typical Applications

• Monitoring peak power consumption

• Monitoring the highest or lowest temperature

(1.97)

[3] OUTPUT

Current

(3.15)

A: 4 – 20 mA DC (Load resistance 750 Ω max.)

B: 2 – 10 mA DC (Load resistance 1500 Ω max.)

C: 1 – 5 mA DC (Load resistance 3000 Ω max.)

D: 0 – 20 mA DC (Load resistance 750 Ω max.)

E: 0 – 16 mA DC (Load resistance 900 Ω max.)

F: 0 – 10 mA DC (Load resistance 1500 Ω max.)

G: 0 – 1 mA DC (Load resistance 15 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

127

(5)

mm (inch)

MODEL: PHS[1]–[2][3]–[4][5]

ORDERING INFORMATION

• Code number: PHS[1]-[2][3]-[4][5]

Specify a code from below for each [1] through [5].

(e.g. PHSH-6A-B/E/Q)

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 100 Ω min.)

4: 0 – 10 V DC (Load resistance 1000 Ω min.)

5: 0 – 5 V DC (Load resistance 500 Ω min.)

6: 1 – 5 V DC (Load resistance 500 Ω min.)

4W: -10 – +10 V DC (Load resistance 2000 Ω min.)

5W: -5 – +5 V DC (Load resistance 1000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

•Special input and output ranges (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

[1] HOLD FUNCTION

H: Peak hold

L: Valley hold

[2] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

F: 0 – 10 mA DC (Input resistance 100 Ω)

PHS SPECIFICATIONS

ES-3207 Rev.3 Page 1/4

http://www.m-system.co.jp/

MODEL: PHS

[4] POWER INPUT

AC Power

INPUT SPECIFICATIONS

■ DC Current:

B: 100 V AC

C: 110 V AC

D: 115 V AC

F: 120 V AC

G: 200 V AC

H: 220 V AC

J: 240 V AC

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

■ DC Voltage: -300 – +300 V DC

Minimum span: 3 mV

Offset: Max. 1.5 times span

Input resistance

Span 3 – 10 mV : ≥ 10 kΩ

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

Span ≥ 1 V : ≥ 1 MΩ

DC Power

S: 12 V DC

R: 24 V DC

V: 48 V DC

■ HOLD CONTROL

P: 110 V DC

Contact rating: 5 V @1 mA

Detection levels: ≤ 1.25 kΩ / 1 V at Track

≥ 20 kΩ / 4 V at Hold

[5] OPTIONS (multiple selections)

LCD Meter (for indicating value being held)

blank: Without

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

/E: With (0.0 - 100.0 % display)

Other Options

Minimum span: 1 mA

blank: none

Offset: Max. 1.5 times span

/Q: Option other than the above (specify the specification)

Load resistance: Output drive 15 V max.

■ DC Voltage: -10 – +12 V DC

Minimum span: 5 mV

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

Offset: Max. 1.5 times span

Load resistance: Output drive 10 mA max.; 5 mA for

negative voltage output; at ≥ 0.5 V

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

INSTALLATION

Power input

• AC: Operational voltage range: rating ±10 %,

50/60 ±2 Hz, approx. 2 VA

GENERAL SPECIFICATIONS

Construction: Plug-in

• DC: Operational voltage range: rating ±10 %, or 85 – 150

V for 110 V rating (ripple 10 % p-p max.) approx. 2 W (90

mA at 24 V)

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Operating temperature: -5 to +60°C (23 to 140°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -10 to +120 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Hold control: Holds when opening the terminals 5 – 6; tracks

when closing them

Weight: 400 g (0.88 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.2 %

Display accuracy: ± (0.2 % of FS + 1 digit)

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

■ DISPLAY (LCD meter)

• Option code: /E

LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)

(No scaling)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

PHS SPECIFICATIONS

ES-3207 Rev.3 Page 2/4

http://www.m-system.co.jp/

MODEL: PHS

EXTERNAL DIMENSIONS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–4.5 (.18) dia.

MTG HOLE

15 (.59) deep

8–M3.5

SCREW

50 (1.97)

107 (4.21)

127 (5)

40 (1.57)

50 (1.97)

[3.3 (.13)]

• When mounting, no extra space is needed between units.

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM)

Input shunt resistor attached

for current input.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

(10 bits)

Isolation

Low Drift

Amplifier

UP / DOWN

Counter

D / A

Converter

Output

Driver

–

Comparator

INPUT

HOLD

OUTPUT

POWER

–

U(+)

V(–)

CONTROL

Gate

Oscillator

Close: Track

Open: Hold

Base Socket

Input shunt resistor attached for current input.

** Option /E

PHS SPECIFICATIONS

ES-3207 Rev.3 Page 3/4

http://www.m-system.co.jp/

MODEL: PHS

Specifications are subject to change without notice.

PHS SPECIFICATIONS

ES-3207 Rev.3 Page 4/4

http://www.m-system.co.jp/

PHSH-C2S 相关器件

型号	制造商	描述	价格	文档
PHSH-C2S/E	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C2S/Q	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3B	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3B/E	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3B/Q	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3C	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3C/E	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3C/Q	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3D	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格
PHSH-C3D/E	MSYSTEM	Plug-in Signal Conditioners M-UNIT	获取价格