概述
数据手册PNS-26-S/Q 概述
Plug-in Signal Conditioners M-UNIT
PNS-26-S/Q 数据手册
通过下载PNS-26-S/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: PNS
Z: Specify current (See OUTPUT SPECIFICATIONS)
Plug-in Signal Conditioners M-UNIT
Voltage
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
5W: -5 – +5 V DC (Load resistance 1000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
ANGLE SENSOR TRANSMITTER
Functions & Features
• Converting a voltage input from Angle Sensor (model:
NRA) into a standard process signal proportional to the
angle
• Isolation up to 2000 V AC
• 50 % zero/span adjustments
• LCD meter
• Highdensity mounting
[3] POWER INPUT
AC Power
Typical Applications
• Tank levels
B: 100 V AC
C: 110 V AC
D: 115 V AC
F: 120 V AC
G: 200 V AC
H: 220 V AC
J: 240 V AC
• Positions
50
(1.97)
80
(3.15)
DC Power
S: 12 V DC
R: 24 V DC
127
(5)
V: 48 V DC
P: 110 V DC
mm (inch)
[4] OPTIONS (multiple selections)
Input Signal Indicator
MODEL: PNS–[1][2]–[3][4]
blank: Without
ORDERING INFORMATION
• Code number: PNS-[1][2]-[3][4]
Specify a code from below for each of [1] through [4].
(e.g. PNS-1A-B/E/Q)
/E: With (0.0 - 100.0 % display)
Other Options
blank: none
/Q: Option other than the above (specify the specification)
• Special output range (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
[1] ACTION
/C02: Polyurethane coating
1: Direct (output increases with input increase)
/C03: Rubber coating
2: Reverse (output increases with input decrease)
TERMINAL SCREW MATERIAL
/S01: Stainless steel
[2] OUTPUT
Current
RELATED PRODUCTS
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
• Brushless angle sensor (model: NRA)
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
PNS SPECIFICATIONS
ES-1354 Rev.3 Page 1/3
http://www.m-system.co.jp/
MODEL: PNS
steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Zero adjustment: 0 – 50 % of linearity-assured range of the
angle sensor (front)
Span adjustment: 50 – 100 % of linearity-assured range of
the angle sensor (front)
■ DISPLAY (Input indicator)
LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)
(No scaling)
INPUT SPECIFICATIONS
Input: 2 – 3 V DC (output from Angle Sensor)
Excitation: 5 V DC ±2 %
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 15 V max.
■ DC Voltage: -10 – +12 V DC
Minimum span: 5 mV
Offset: Max. 1.5 times span
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
INSTALLATION
Power input
• AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 2 VA
• DC: Operational voltage range: rating ±10 %, or 85 – 150
V for 110 V rating (ripple 10 % p-p max.)
approx. 2 W (80 mA at 24 V)
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 300 g (0.66 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
Display accuracy: ±(0.1 % of FS + 1 digit)
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
PNS SPECIFICATIONS
ES-1354 Rev.3 Page 2/3
http://www.m-system.co.jp/
MODEL: PNS
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–M3.5
SCREW
50 (1.97)
107 (4.21)
127 (5)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
*
red
EXC.
Excitation
Supply
3
4
5
6
Z
S
Isolation
Angle
Sensor
yellow INPUT
Low Drift
Amplifier
Output
Driver
1
2
7
8
+
(model: NRA)
OUTPUT
POWER
white
COM
–
U(+)
V(–)
Base Socket
*Option /E
Specifications are subject to change without notice.
PNS SPECIFICATIONS
ES-1354 Rev.3 Page 3/3
http://www.m-system.co.jp/
PNS-26-S/Q 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| PNS-26-V | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-26-V/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-26-V/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-B | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-B/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-B/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-C | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-C/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-C/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| PNS-2A-D | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
PNS-26-S/Q 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
