R3-NEIP1 [MSYSTEM]

Remote I/O R3 Series EtherNet/IP INTERFACE MODULE;


型号：	R3-NEIP1
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series EtherNet/IP INTERFACE MODULE
文件：	总6页 (文件大小：178K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3-NEIP1

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

Remote I/O R3 Series

EtherNet/IP INTERFACE MODULE

Functions & Features

• Converts analog and discrete I/O data to the open network

fieldbus (EtherNet/IP)

GENERAL SPECIFICATIONS

Connection

Ethernet: RJ-45 Modular Jack

Typical Applications

Internal bus: Via the Installation Base (model: R3-BSx)

Internal power: Via the Installation Base (model: R3-BSx)

RUN contact output: M3 separable screw terminal (torque

0.5 N·m)

• Remote I/O for DCS and PLC

27.5 [1.08]

Screw terminal: Nickel-plated steel

Isolation: EtherNet/IP to internal bus or internal power to

RUN contact output

130

[5.12]

Input error data setting: Input value setting at input module

error with side DIP SW

Dual communication setting: Set with the side DIP switch

Data allocation setting: Set with the side DIP switch

■ RUN CONTACT OUTPUT

109

[4.29]

mm [inch]

RUN contact: Turns ON when both MS and NS LEDs are

green (EtherNet/IP in normal communication).

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

MODEL:R3–NEIP1[1]

(Less than 50 V AC to conform with EU Directive)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

ORDERING INFORMATION

• Code number: R3-NEIP1[1]

Specify a code from below for [1].

(e.g. R3-NEIP1/CE/Q)

Mechanical life: 2 × 10 cycles (300 cycles/min.)

• Specify the specification for option code /Q

(e.g. /C01)

When driving an inductive load, external contact protection

and noise quenching recommended.

[1] OPTIONS (multiple selections)

Standards & Approvals

blank: Without CE

EtherNet/IP COMMUNICATION

Communication Standard: IEEE 802.3u

Transmission: 10BASE-T, 100BASE-TX

Baud rate: 10/100 Mbps (Auto Negotiation function)

Max. number of socket connections: 3

Connection type: Exclusive owner, Listen only, Input only

Protocol: EtherNet/IP

/CE: CE marking

Other Options

blank: none

/Q: Option other than the above (specify the specification)

Transmission media: 10BASE-T (STP, Category 5)

100BASETX (STP, Category 5e)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

Max. length of fieldbus segment: 100 meters

IP address: 192.168.0.1 (factory setting); Selectable with PC

Configurator Software (model: R3CON)

BOOTP and DHCP available

/C02: Polyurethane coating

/C03: Rubber coating

Port No.: 44818

I/O data area size: Input and output data area size set with

side DIP SW

RELATED PRODUCTS

• PC configurator software (model: R3CON)

• EDS file

Required data words:

Input: 35, 67, 131, 252 words

The EDS file and configurator software are downloadable at

M-System’s web site.

Output: 35, 67, 131, 252 words (3 words are used only for

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 1/6

https://www.m-system.co.jp/

MODEL: R3-NEIP1

status)

Ethernet indicator LED: TX/RX, LINK

MS (Module Status) indicator: Bi-color (green/red) LED

indicates device status.

NS (Network Status) indicator: Bi-color (green/red) LED

indicates status of the communication link.

Note: Not connectable beyond router.

INSTALLATION

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

PERFORMANCE

Current consumption: 130 mA

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(EtherNet/IP to internal bus or internal power to RUN contact

output)

2000 V AC @ 1 minute (power input to FG; isolated on the

power supply module)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

EXTERNAL VIEW

■ FRONT VIEW

■ SIDE VIEW

MS Indicator LED

NS Indicator LED

Functions

SW3

SW2

SW1

Ethernet Indicator

Configuration Jack

RJ-45 Modular Jack

LINK

TX/RX

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 2/6

https://www.m-system.co.jp/

MODEL: R3-NEIP1

TRANSMISSION DATA DESCRIPTIONS

The DIP SW located at the side of the module specifies each I/O module's data allocation (occupied data area and size of the I/O data area).

For example, when the data areas are assigned as shown below:

Module 1

Module 2

Module 3

Module 4

Module 5

Module 6

Module 7

I/O data area: 252 words each for input and output.

Then the I/O data are assigned as in the figures below:

■ INPUT DATA

■ OUTPUT DATA

The figure below shows the allocation of the data sent from

the master to the network module.

The figure below shows the allocation of the data sent from

the network module to the master.

Begin

Address +0

Begin

Address +0

Module 1

Module 2

Module 3

Module 1

Module 2

Module 3

+10

+12

+14

+16

+10

+12

+14

+16

Module 4

Module 5

Module 6

Module 7

Module 4

Module 5

Module 6

Module 7

+249

+251

Module Status

Error Status

+249

Data Error Status

+251

The area enclosed with bold line is assigned for I/O data

Module Status, Error Status and Data Error Status are assigned to the last three words of the output data respectively.

Each module can handle either input or output data.

• Module Status indicates whether individual I/O module are mounted or not. The bit corresponding to the mounted slots

turns to “1,” and the unmounted slots to “0.”

• Error Status indicates error status for each module as described below. The bit corresponding to such modules turns to “1.”

R3-TSx, R3-RSx, R3-US4 (T/C or RTD input): Input burnout

R3-DA16A: Power input in error or disconnected

R3-YSx: Output current error (e.g. load unconnected)

R3-PC16A: External power supply in error or disconnected

• Data Error Status indicates overrange (R3-US4: out of -10% to +110%; the other types: out of -15% to +115%) status for each

module. The bit corresponding to such modules turns to “1.”

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 3/6

https://www.m-system.co.jp/

MODEL: R3-NEIP1

MODULE STATUS, ERROR STATUS, DATA ERROR STATUS

Shows each module's availability and error status.

Module 1

Module 2

Module 3

Module 16

I/O DATA DESCRIPTIONS

The data allocations for typical I/O modules are shown below.

Refer to the manual for each module for detailed data allocations.

■ ANALOG DATA (16-bit data, models: R3-SV4, YV4, DS4, YS4, US4, etc.)

16-bit binary data.

Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

-15 to 0 % is a negative range represented in 2’s complement.

In case of R3-US4, -10 to 0% is a negative range represented in 2's complement.

■ TEMPERATURE DATA (16-bit data, models: R3-RS4, TS4, US4, etc.)

16-bit binary data.

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data.

For example, 135.4°F is converted into 135.

Minus temperature is converted into negative values, represented in 2’s complements.

■ ANALOG DATA (16-bit data, models: R3-CT4A, CT4B, etc.)

16-bit binary data.

Integer obtained by multiplying unit value (A) by 100.

In case of CLSE-R5, integer obtained by multiplying unit value (A) by 1000.

■ ACCUMULATED COUNT DATA (32-bit data, models: R3-PA2, PA4A, WT1, WT4, etc.)

32-bit binary data is used for accumulated counts and encoder positions.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 4/6

https://www.m-system.co.jp/

MODEL: R3-NEIP1

■ BCD DATA (32-bit data, models: R3-BA32A, BC32A, etc.)

32-bit binary data is used for BCD.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

■ 16-POINT DISCRETE DATA (models: R3-DA16, DC16, etc.)

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 16 (Output 16)

0 : OFF

1 : ON

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

27.5 [1.08]

109 [4.29]

POSITIONING

GUIDE

6–M3

SCREW

TERMINAL

COVER

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 5/6

https://www.m-system.co.jp/

MODEL: R3-NEIP1

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

LED

Isolation

Control

Communication

Circuit

RJ-45 MODULAR JACK

EtherNet/IP

INTERNAL BUS

Circuit

RUN +

ETHERNET DIP SW

LED

RUN CONTACT OUTPUT

RUN –

INTERNAL POWER

JACK

CONFIGURATION JACK

SYSTEM CONFIGURATION EXAMPLES

EtherNet/IP

Master Station

Ethernet

Hub

Ethernet

EtherNet/IP Interface Module

model: R3-NEIP1

EtherNet/IP Interface Module

model: R3-NEIP1

Specifications are subject to change without notice.

R3-NEIP1 SPECIFICATIONS

ES-8466 Rev.6 Page 6/6

https://www.m-system.co.jp/

R3-NEIP1 [MSYSTEM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB