R3-YV4V [MSYSTEM]
Remote I/O R3 Series DC VOLTAGE OUTPUT MODULE;
| 型号： | R3-YV4V |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R3 Series DC VOLTAGE OUTPUT MODULE 输出元件 |
| 文件： | 总4页 (文件大小：132K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R3S-YV4
size: 0.2 to 1.5 mm
2
, stripped length 10 mm)
Remote I/O R3 Series
Internal power: Via the Installation Base (model: R3-BSx)
Isolation: Output 1 to output 2 to output 3 to output 4 to
internal bus or internal power
DC VOLTAGE OUTPUT MODULE
(4 points, isolated, tension clamp terminal block)
Output range: Selectable with the side DIP SW
Output hold function: Setting for communication error with
side DIP SW
27.5 (1.08)
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Green LED turns on in normal operating
conditions.
130 (5.12)
120 (4.72)
mm (inch)
OUTPUT SPECIFICATIONS
■ Narrow Span: -1 – +1 V, 0 – 1 V DC
Load resistance: 10 kΩ min.
MODEL: R3S-YV4[1][2]
■ Wide Span: -10 – +10 V, -5 – +5 V, 0 – 10 V, 0 – 5 V, 1 – 5
V DC
ORDERING INFORMATION
• Code number: R3S-YV4[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R3S-YV4W/Q)
Load resistance: 10 kΩ min.
■ Output Range
Except -10 to +10 V DC: -15 to +115 % of output range
-10 to +10 V DC: Approx. -11.5 to +11.5 V DC
• Specify the specification for option code /Q
(e.g. /C01/SET)
INSTALLATION
NO. OF CHANNELS
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 200 g (0.44 lb)
4: 4
[1] COMMUNICATION MODE
S: Single
W: Dual
PERFORMANCE
Conversion accuracy (Range):
[2] OPTIONS
blank: none
-10 – +10 V : ±0.05 %
/Q: With options (specify the specification)
-5 – +5 V : ±0.05 %
-1 – +1 V : ±0.05 %
0 – 10 V : ±0.05 %
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
0 – 5 V : ±0.1 %
1 – 5 V : ±0.1 %
0 – 1 V : ±0.1 %
/C02: Polyurethane coating
Data range: 0 – 10000 of the output range
Data allocation: 4
/C03: Rubber coating
EX-FACTORY SETTING
Current consumption: 150 mA
Temp. coefficient: ±0.015 % /°C (±0.008 %/°F)
(±0.03 % /°C [±0.02 %/°F] with 0 – 5 V or 1 – 5 V range)
Response time: ≤ 0.2 sec. (0 – 90 %)
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute (output 1 to
output 2 to output 3 to output 4 to internal bus or internal
power)
/SET: Preset according to the Ordering Information Sheet
(No. ESU-8372)
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R3-BSx)
Output: Separable tension clamp terminal (applicable wire
R3S-YV4 SPECIFICATIONS
ES-8940 Rev.5 Page 1/4
http://www.m-system.co.jp/
MODEL: R3S-YV4
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
FUNCTIONS
■OUTPUT HOLD or OUTPUT OFF
In normal conditions, the module outputs the signal from
the preferred bus A. When an error is detected, the output
is switched to the data from the bus B.
•Output Hold
If both are in error, the module holds the signal and stands
by until one of the communications recovers.
•Output OFF
If both are in error, the module outputs -15 % (or approx.
-11.5 V) and stands by until one of the communications
recovers.
At the startup, it outputs -15 % (or approx. -11.5 V) until the
communication is established and normal data is received.
EXTERNAL VIEW
■ SIDE VIEW
■ FRONT VIEW
RUN LED
ERR LED
Functions
1
SW3
ON
SW2
SW1
Range
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Output 2 (SW1)
or
Output 4 (SW2)
Output
Hold
Output 1 (SW1)
or
Output 3 (SW2)
ON
ON
20
EXTERNAL DIMENSIONS unit: mm (inch)
120 (4.72)
109 (4.29)
27.5 (1.08)
POSITIONING
GUIDE
1
20
R3S-YV4 SPECIFICATIONS
ES-8940 Rev.5 Page 2/4
http://www.m-system.co.jp/
MODEL: R3S-YV4
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN LED ERR LED
DIP SW
Output Circuit
1
3
+
+
–
+
+
–
+
+
–
+
+
–
INTERNAL BUS A
Comm.
Circuit
WIDE SPAN
OUTPUT 1
INTERNAL BUS B*1
NARROW SPAN
2
Output Circuit
Output Circuit
Output Circuit
5
INTERNAL POWER
WIDE SPAN
NARROW SPAN
OUTPUT 2
OUTPUT 3
OUTPUT 4
7
9
Control
Circuit
6
10
11
13
12
15
17
16
4
WIDE SPAN
NARROW SPAN
WIDE SPAN
NARROW SPAN
SLD
SLD
SLD
SLD
8
14
18
19
20
SLD
SLD
*2
*1. For dual redundant communication.
*2. To use shield line, connect it to SLD terminal and ground the terminal 20.
Note: Do not connect wide span and narrow span simultaneously within the same channel.
Do not use void terminals.
OUTPUT TERMINAL ASSIGNMENT
PIN No.
1
FUNCTION
VH1
2
COM1
VL1
3
4
SLD
5
VH2
6
COM2
VL2
7
8
SLD
9
NC
10
11
12
13
14
15
16
17
18
19
20
NC
VH3
COM3
VL3
SLD
VH4
COM4
VL4
SLD
SLD
SLD
R3S-YV4 SPECIFICATIONS
ES-8940 Rev.5 Page 3/4
http://www.m-system.co.jp/
MODEL: R3S-YV4
Specifications are subject to change without notice.
R3S-YV4 SPECIFICATIONS
ES-8940 Rev.5 Page 4/4
http://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明