R5-DC4 [MSYSTEM]
Remote I/O R5 Series DISCRETE OUTPUT MODULE;
| 型号： | R5-DC4 |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R5 Series DISCRETE OUTPUT MODULE 输出元件 |
| 文件： | 总3页 (文件大小：113K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R5-DC4
internal power
Remote I/O R5 Series
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
Output status indicator: Red LED; turns on with the outputs
ON.
DISCRETE OUTPUT MODULE
(relay contact output, 4 points)
18 (.71)
OUTPUT SPECIFICATIONS
Output: Relay contact, 4 points
90
(3.54)
Common: Every 2 points
Rated load: 250 V AC @ 0.5 A (cos ø = 1)
30 V DC @ 0.5 A (resistive load)
96.5
(3.80)
mm (inch)
Maximum switching voltage: 250 V AC or 30 V DC
Maximum switching power: 250 VA or 150 W
Minimum load: 1 V DC @ 1 mA
MODEL: R5–DC4[1][2]
Mechanical life: 2 × 10 cycles (rate 300/min.)
7
When driving an inductive load, external contact protection
and noise quenching recommended.
ORDERING INFORMATION
• Code number: R5-DC4[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R5-DC4W/Q)
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R5-BS)
Weight: 100 g (0.22 lb)
• Specify the specification for option code /Q
(e.g. /C01)
NO. OF CHANNELS
4: 4-point outputs
PERFORMANCE
Data allocation: 1
[1] COMMUNICATION MODE
S: Single
Response time: ≤ 0.1 sec.
W: Dual
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute (Do 1 or Do 2 to
Do 3 or Do 4 to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
[2] OPTIONS
blank: none
/Q: With options (specify the specification)
STANDARDS & APPROVALS
EU conformity:
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
EMC Directive
EMI EN 61000-6-4
/C02: Polyurethane coating
EMS EN 61000-6-2
/C03: Rubber coating
Low Voltage Directive
EN 61010-1, EN 61010-2-201
Measurement Category II (output)
Pollution Degree 2
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R5-BS)
Output: Euro type connector terminal
Output to internal bus or internal power – Basic insulation
(300 V)
(Applicable wire size: 0.2 – 2.5 mm
2
(AWG24 - 12),
RoHS Directive
stripped length 7 mm)
Internal power: Via the base (model: R5-BS)
Isolation: Do1 or Do2 to Do3 or Do4 to internal bus or
R5-DC4 SPECIFICATIONS
ES-6126 Rev.10 Page 1/3
https://www.m-system.co.jp/
MODEL: R5-DC4
FUNCTIONS
Output hold function:
In normal conditions, the module outputs the signal from
the preferred bus A.
When an error is detected, the output is switched to the
data from the bus B.
If both are in error, the module holds the signal and stands
by until one of the communications recovers.
At the startup, it outputs OFF until the communication is
established and normal data is received.
EXTERNAL VIEW
FRONT VIEW
SIDE VIEW
RUN LED
RUN
1
Status Indicator LED
2
3
4
1 2 3 4 5 6 7 8
DO NOT USE
4
1
5
2
6
3
Euro Type
Connector Terminals
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
LOCKING CLAMP
18 (.71)
6.5
90 (3.54)
(.26)
4
1
5
2
6
3
POSITIONING GUIDE
R5-DC4 SPECIFICATIONS
ES-6126 Rev.10 Page 2/3
https://www.m-system.co.jp/
MODEL: R5-DC4
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN OUTPUT STATUS
LED INDICATOR LED
•
• • • •
Isolation
Isolation
INTERNAL BUS A
1
2
Communication
Circuit
1
2
3
4
5
6
Do 1
*INTERNAL BUS B
Do 2
Control
Circuit
COM1
Do 3
3
4
INTERNAL POWER
Do 4
COM2
*For dual redundant communication.
Note: Italic typed numbers correspond to the LEDs on the front panel.
Specifications are subject to change without notice.
R5-DC4 SPECIFICATIONS
ES-6126 Rev.10 Page 3/3
https://www.m-system.co.jp/
相关型号：
R5-E-WHT-BLK-C-F-0
Rocker Switch, DPDT, On-(on), Momentary, Quick Connect Terminal, Rocker Actuator, Panel Mount
E-SWITCH
©2020 ICPDF网 联系我们和版权申明