R9LWTU-2001-AD4 [MSYSTEM]
Remote I/O R9 Series MULTI POWER MONITORING UNIT;
| 型号： | R9LWTU-2001-AD4 |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R9 Series MULTI POWER MONITORING UNIT 监视器 |
| 文件： | 总7页 (文件大小：258K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R9LWTU
Remote I/O R9 Series
EXTENSION UNIT
1: With connection
MULTI POWER MONITORING UNIT
(Clamp-on current sensor CLSE, LonWorks)
Functions & Features
AUXILIARY POWER SUPPLY
AD4: universal
• Multi Power Monitoring Unit for LonWorks.
• By using clamp-on current sensors, there is no need of
current transformers.
100 – 240 V AC (Operational range 85 – 264 V, 50 / 60 Hz) /
110 – 240 V DC (Operational range 99 – 264 V,
ripple 10 %p-p max)
• Up to 8 circuits can be measured. (Common voltage
measurement)
[1] OPTIONS
blank: none
• Current sensors are easy to install in existing systems.
Wide input range of 5 to 600 A is availabe.
• All measured values, counter values, display mode,
setting data are stored in the non-volatile memory when
power is off.
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• By using SD card, data logging of current and power etc.
with calendar is available.
/C02: Polyurethane coating
/C03: Rubber coating
125 (4.92)
RELATED PRODUCTS
• Discrete I/O extension unit (model: R9WTU-ED)
• Multi power monitoring extension unit (model: R9WTU-EP)
• PC configurator software (model: PMCFG)
• XIF File (Device Interface File)
140 (5.51)
XIF file is used to define a LonWorks device when
programmed on LonMaker.
80 (3.15)
mm (inch)
The XIF files and Software are downloadable at M-System’s
web site.
To connect the module to a PC a dedicated cable is required
(refer to M-System's web site or instruction manual).
• Clamp-on current sensor (model: CLSE)
The clamp-on current sensors, not included in this product
package, must be ordered separately. Required number
depends upon the system configuration.
• SD card
MODEL: R9LWTU–2001–AD4[1]
ORDERING INFORMATION
• Code number: R9LWTU-2001-AD4[1]
Specify a code from below for [1].
(e.g. R9LWTU-2001-AD4/Q)
• Specify the specification for option code /Q
(e.g. /C01)
A SD card is required to store data in the unit.
Use the specified model number of memory card.
Available for purchase from M-System. Consult M-System.
- Hagiwara Solutions NSD6-004GH(B21SEI
(NSD6-004GH(A00SDI, NSDA-004GT,
CONFIGURATION
2: Single-phase/2-wire, 3-phase/3-wire, single-phase/3-wire; 8 circuits
NSDA-004GL ... discontinued)
- Apacer Technology AP-ISD04GIS4B-3T
(AP-ISD04GIS4B-T ... discontinued)
CONNECTION
0: Terminal block
GENERAL SPECIFICATIONS
Construction: Stand-alone
I/O
0: Without
Degree of protection: IP20
Connection
Auxiliary power or voltage input: M3.5 screw terminals
(torque 0.8 N·m)
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 1/7
http://www.m-system.co.jp/
MODEL: R9LWTU
Current input: M3 screw terminals (torque 0.5 N·m)
LonWorks: M3 screw terminals (torque 0.5 N·m)
Solderless terminal: Refer to the drawing at the end of the
section.
LonWorks COMMUNICATION
Neuron Chip: FT3120 (NeuronID printed in numbers and bar
code [peel-off code 39 format])
Transceiver: FT-X1 (equivalent to FTT10A)
Transmission speed: 78 kbps
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
Twisted-pair cable
Applicable wire size
Distance, free topology: 500 meters
Max. 64 nodes/channel
M3 screw terminal: 0.25 to 1.65 mm
2
(AWG 22 to 16)
(AWG 16 to 14)
M3.5 screw terminal: 1.04 to 2.63 mm
2
LNS: Ver. 3.0 Service Pack 8 or higher
Status indicator: ONLINE, ERR, TX/RX, SVCE (service)
Operation switch: Service, reset
Configuration: Single-phase/2-wire, single-phase/3-wire, 3-
phase/3-wire
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Sensor core to sensor output or current input or
voltage input to LonWorks to auxiliary power to FE1
■ Measured variables
INPUT SPECIFICATIONS
Frequency: 50 / 60 Hz (45 – 65 Hz)
• Voltage Input
Rated voltage
Voltage: R – N, S – N, T – N, R – S, S – T, T – R
Current: R, S, T, N
•Between lines: 400 V AC
•Line-neutral (phase voltage): 230 V (single-phase / 2-wire
and 3-wire)
Active / reactive / apparent power: R, S, T, Σ
Power factor: R, S, T, Σ
Input burden: ≤ ULN2 / 300 kΩ / phase
Overload capacity: 200 % of rating for 10 sec., 120 %
continuous
Frequency
Active energy: Incoming
Reactive energy: Incoming lag
Selectable primary voltage range: 50 – 400 000 V
• Current Input
Active / reactive / apparent power intervals (demand)
Average (demand) current: R, S, T, N
Harmonic contents: Σ
CLSE-R5: 0 – 5 A AC
CLSE-05: 0 – 50 A AC
Voltage: R - N, S - N, T - N, R - S, S - T, T - R
Current: R, S, T, N
CLSE-10: 0 – 100 A AC
CLSE-20: 0 – 200 A AC
Max. and min. values
CLSE-40: 0 – 400 A AC
Calendar log (inserting SD card): Voltage, Current, power,
electric energy, power factor
CLSE-60: 0 – 600 A AC
Overload capacity: 120 % continous, 500 % for 10 sec.
Note: Use for the circuit not exceed 480 V
Selectable primary current range: 1 – 20 000 A (Using CLSE-
R5 the unit is configurable only with LonMaker.)
Operational range
Operating mode setting: Connection, clamp-on sensor
selection
Status indicators: Power, SD Card
■Recommended solderless terminal size - M3
3.3 (.13) max
Current: 0 – 120 % of the rating
Voltage: 10 – 120 % of the rating
Apparent power: ≤ 120 % of the rating
Active/reactive power: ±120 % of the rating
Frequency: 45 – 65 Hz
mm (inch)
■Recommended solderless terminal size - M3.5
3. (.1 ) max
Power factor: ±1
INSTALLATION
Auxiliary power supply
•AC: < 9 VA
mm (inch)
•DC: < 3 W
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Surface or DIN rail
Weight: 500 g (1.1 lb)
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 2/7
http://www.m-system.co.jp/
MODEL: R9LWTU
PERFORMANCE
Accuracy (at 10 - 35°C or 50 - 95°F, 45 – 65 Hz)*1
Add the accuracy of the current sensor for overall values.
Voltage: ±0.5 % of the rating*2
Current: ±0.5 % of the rating*2
Power: ±0.5 % of the rating*2
Power factor: ±1.5 %
Frequency: ±0.1 % of the rating*2
Energy: ±1 %
Harmonic contents: ±2 % of the rating*2
*1. Sensor error margin not included
*2. The described accuracy levels are ensured at the input
1% or more for neutral current in a 1-phase/3-wire circuit
and phase-S current in an unbalanced 3-phase/3-wire
circuit.
Data update period:
Harmonic contents and frequency: ≤ 1 sec.
Other: ≤ 500 msec.
Calendar clock: (with battery backup)
Accuracy: Monthly deviation 3 minutes at 25°C
Back up period: Approx. 2 years at 25°C without power
With the power on, no battery drain
Battery: Primary lithium battery (non-removable)
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @ 1 minute
(current input or voltage input to LonWorks to auxiliary
power or FE1)
EXTERNAL VIEW
FRONT VIEW
9
8ch
8
8ch
7
7ch
6
7ch
5
6ch
4
6ch
3
5ch
2
5ch
1
3
2
1
LONWORKS Terminals
Terminal Block, Current Input 2
T2 3L 1L 3L 1L 3L 1L 3L 1L
18 8ch 17 8ch 16 7ch 15 7ch 14 6ch 13 6ch 12 5ch 11 5ch 10
FE NET2 NET1
7
6
5
4
NC NC NET2 NET1
T1 3K 1K 3K 1K 3K 1K 3K 1K
SD Card Slot
SDCard
Service / Reset SW
Service Reset
Power
ONLINE
ERR
TX/RX
Operating Mode Setting DIP SW (SW1)
PC Configurator Connection Jack
Status Indicator LED
SVCE
Terminal Block,
Voltage Input / Auxiliary Power Supply
10 1ch 11 1ch 12 2ch 13 2ch 14 3ch 15 3ch 16 4ch 17 4ch 18
NC 1K 3K 1K 3K 1K 3K 1K 3K
4
5
6
7
P1 P2 P3
1
N
3
Terminal Block, Current Input 1
2
1
1ch
2 1ch 3 2ch 4 2ch 5 3ch 6 3ch 7 4ch 8 4ch 9
(
U +
)
(-)
V
FE1
NC 1L 3L 1L 3L 1L 3L 1L 3L
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 3/7
http://www.m-system.co.jp/
MODEL: R9LWTU
TERMINAL CONNECTIONS
Use the model CLSE clamp sensor for current inputs.
The figure below shows only one circuit.
A maximum of eight (8) current sensor inputs can be connected (Ch. 1 through Ch. 8).
Grounding is not required for low voltage circuits.
System /
Application
System /
Application
Terminal
Terminal
P1 P2 P3 1K 1L
P1
N
1K 1L
k
l
source
L1
load
k
l
source
L1
load
K
L
K
L
L2
L3
Three-phase
/ 3-wire
N
Single-phase
/ 2-wire
balanced
load
P1 P2 P3
1K 1L
P1
N
1K 1L
u
v
v
u
u
v
k
l
source
L1
load
k
l
U
V
V
U
source
L1
U
V
load
K
L
K
L
L2
L3
N
P1
N P3 1K 1L 3K 3L
P1 P2 P3 1K 1L 3K 3L
k
l
source
L1
N
load
k
l
source
L1
load
K
L
k
l
K
L
k
l
L2
L3
Three-phase
/ 3-wire
L2
K
L
K
L
Single-phase
/ 3-wire
unbalanced
load
P1
N
P3
1K 1L 3K 3L
P1 P2 P3
1K 1L 3K 3L
u
v
v
u
u
v
v
u
k
l
source
L1
load
U
V
V
U
k
l
source
L1
load
U
V
V
U
K
L
k
l
K
L
k
l
N
L2
L3
L2
K
L
K
L
COMMUNICATION CABLE CONNECTIONS
■ MASTER CONNECTION
MASTER UNIT
LONWORKS
R9LWTU
R9LWTU
LONWORKS
LONWORKS
Terminator
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 4/7
http://www.m-system.co.jp/
MODEL: R9LWTU
TERMINAL ASSIGNMENTS
• Network
• Current Input 2
9
8ch
3L
8
8ch
1L
7
7ch
3L
6
7ch
1L
5
6ch
3L
4
6ch
1L
3
5ch
3L
2
5ch
1L
1
3
2
1
T2
FE NET2 NET1
18 8ch 17 8ch 16 7ch 15 7ch 14 6ch 13 6ch 12 5ch 11 5ch 10
7
6
5
4
T1
3K
1K
3K
1K
3K
1K
3K
1K
NC NC NET2 NET1
No.
ID
FUNCTION
No.
ID
FUNCTION
No.
ID
FUNCTION
1
2
3
4
5
6
7
NET1 LONWORKS comm. 1
NET2 LONWORKS comm. 2
1
2
3
4
5
6
7
8
9
5ch 1L Ch.5, Current input 1L
5ch 3L Ch.5, Current input 3L
6ch 1L Ch.6, Current input 1L
6ch 3L Ch.6, Current input 3L
7ch 1L Ch.7, Current input 1L
7ch 3L Ch.7, Current input 3L
8ch 1L Ch.8, Current input 1L
8ch 3L Ch.8, Current input 3L
10
11
12
13
14
15
16
17
18
5ch 1K Ch.5, Current input 1K
5ch 3K Ch.5, Current input 3K
6ch 1K Ch.6, Current input 1K
6ch 3K Ch.6, Current input 3K
7ch 1K Ch.7, Current input 1K
7ch 3K Ch.7, Current input 3K
8ch 1K Ch.8, Current input 1K
8ch 3K Ch.8, Current input 3K
FE
Comm. ground
NET1 LONWORKS comm. 1
NET2 LONWORKS comm. 2
NC
NC
Unused
Unused
T2
Unused
T1
Unused
• Auxiliary Power Supply, Voltage Input
• Current Input 1
4
5
6
7
10 1ch 11 1ch 12 2ch 13 2ch 14 3ch 15 3ch 16 4ch 17 4ch 18
P1
P2
P3
N
NC
1K
3K
1K
3K
1K
3K
1K
3K
1
2
3
1
1ch
2
1ch
3
2ch
4
2ch
5
3ch
6
3ch
7
4ch
8
4ch
9
U(+) V(−) FE1
NC
1L
3L
1L
3L
1L
3L
1L
3L
No.
ID
FUNCTION
No.
ID
FUNCTION
Unused
No.
ID
FUNCTION
Unused
1
2
3
4
5
6
7
U(+) Auxiliary power (+)
V(−) Auxiliary power (−)
FE1 Power ground
1
2
3
4
5
6
7
8
9
NC
10
11
12
13
14
15
16
17
18
NC
1ch 1L Ch.1, Current input 1L
1ch 3L Ch.1, Current input 3L
2ch 1L Ch.2, Current input 1L
2ch 3L Ch.2, Current input 3L
3ch 1L Ch.3, Current input 1L
3ch 3L Ch.3, Current input 3L
4ch 1L Ch.4, Current input 1L
4ch 3L Ch.4, Current input 3L
1ch 1K Ch.1, Current input 1K
1ch 3K Ch.1, Current input 3K
2ch 1K Ch.2, Current input 1K
2ch 3K Ch.2, Current input 3K
3ch 1K Ch.3, Current input 1K
3ch 3K Ch.3, Current input 3K
4ch 1K Ch.4, Current input 1K
4ch 3K Ch.4, Current input 3K
P1
P2
P3
N
Voltage input P1
Voltage input P2
Voltage input P3
Voltage input N
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 5/7
http://www.m-system.co.jp/
MODEL: R9LWTU
EXTERNAL DIMENSIONS unit: mm (inch)
43−M3 SCREW TERMINAL
6 (.24)
4 − 4.5 (.18) dia. MTG HOLE
DIN RAIL
35 mm wide
75 (2.95)
6.5 (.25)
[4 (.16)]
125 (4.92)
80 (3.15)
7−M3.5 SCREW TERMINALS
7.3 (.29)
MOUNTING REQUIREMENTS unit: mm (inch)
■ SINGLE MOUNTING
75 (2.95)
4–M4
Pitch 130 (5.12) min.
■ BASIC + EXTENSION UNIT
75 (2.95)
70.5 (2.78)
6–M4
Pitch 223 (8.78) min.
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 6/7
http://www.m-system.co.jp/
MODEL: R9LWTU
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
LONWORKS
NET1
1
4
2
5
3
6
7
U(+)
V(−)
FE1
P1
1
2
3
4
5
6
7
AUXILIARY
POWER SUPPLY
NET1
NET2
NET2
FE
Isolation
LONWORKS
Comm.
Circuit
AUX. POWER
SUPPLY
VOLTAGE INPUT
COMMUNICATION
P2
VOLTAGE
NC
P3
NC
N
11
2
10
1
1K
1L
3K
3L
1K
1L
3K
3L
Ch.1 CURRENT
Ch.2 CURRENT
Ch.3 CURRENT
Ch.4 CURRENT
Ch.5 CURRENT
Ch.6 CURRENT
Ch.7 CURRENT
Ch.8 CURRENT
12
3
11
2
13
4
12
3
1K
1L
3K
3L
1K
1L
3K
3L
Control
Circuit
14
5
13
4
15
6
14
5
1K
1L
3K
3L
1K
1L
3K
3L
CURRENT
INPUT 1
CURRENT
INPUT 2
16
7
15
6
17
8
16
7
1K
1L
3K
3L
1K
1L
3K
3L
T2
T1
18
9
17
8
9
1
NC
NC
18
10
Specifications are subject to change without notice.
R9LWTU SPECIFICATIONS
ES-6223 Rev.7 Page 7/7
http://www.m-system.co.jp/
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明