概述
数据手册RPPD-AA7NM1N-K 概述
Plug-in Signal Conditioners M-UNIT
RPPD-AA7NM1N-K 数据手册
通过下载RPPD-AA7NM1N-K数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: RPPD
Plug-in Signal Conditioners M-UNIT
[2] INPUT 2
Must be the same code as the one chosen for Input 1.
PULSE ISOLATOR
(built-in excitation; rotary encoder use)
[3] EXCITATION
Functions & Features
1: 5 V DC @ 120 mA
• Galvanically isolating two pulse rate signals from a rotary
encoder
4: 12 V DC @ 60 mA
7: 24 V DC @ 25 mA
• Various outputs (relay, open collector, voltage pulses and
RS-422 line driver pulse)
Excitation is not provided with input code J, but select code
1.
• Different I/O specs can be specified
• Converting RS-422 line driver pulse input into an open
collector pulse
[4] OUTPUT 1
A: Open collector (max. 100 kHz)
• Excitation
M: 5 V pulse (max. 100 kHz)
• Isolation up to 2000 V AC
N: 12 V pulse (max. 100 kHz)
P: 24 V pulse (max. frequency 50 kHz)
H: High power photo MOSFET relay (max. 20 Hz)
(Option /CE Not available)
• High-density mounting
Typical Applications
• Isolating field pulse signals in order to reduce noises
J: RS-422 line driver pulse (max. 100 kHz)
( ) = Max. frequency
50
(1.97)
[5] OUTPUT 2
A: Open collector (max. frequency 100 kHz)
M: 5 V pulse (max. frequency 100 kHz)
N: 12 V pulse (max. frequency 100 kHz)
P: 24 V pulse (max. frequency 50 kHz)
J: RS-422 line driver pulse (max. 100 kHz)
The max. frequency is in parentheses.
■ OUTPUT COMBINATIONS
80
(3.15)
136
(5.35)
mm (inch)
The table below shows the selectable type of Output 1 for
each Output 2 type.
MODEL: RPPD–[1][2][3][4][5][6][7]–[8][9]
With the Output 2 other than code A, the Output 1 must be
the same type.
ORDERING INFORMATION
• Code number: RPPD-[1][2][3][4][5][6][7]-[8][9]
Specify a code from below for each [1] through [9].
(e.g. RPPD-DD4AA3N-R/CE/Q)
OUTPUT2
OUTPUT1
A
M
N
P
J
A, M, N, P, H
M
N
P
J
• Output pulse width (e.g. 75 msec.)
• Use Ordering Information Sheet (No. ESU-1693). Default
setting will be used if not otherwise specified. Refer to the
factory default setting.
[6] OUTPUT PULSE WIDTH
1: Equal to the input
• Specify the specification for option code /Q
(e.g. /C01/S01)
3: One-shot output (std. pulse width 50 msec.)
(Specify when optional pulse width is required.)
[1] INPUT 1
A: Dry contact
[7] OUTPUT LOGIC (both Output 1 & 2)
N: The same as the input
B: Voltage pulse (Specify sensitivity)
C: 5 V pulse (sensitivity 2 V)
D: 12 V/24 V pulse (sensitivity 5 V)
H: Two-wire current pulse
J: RS-422 line driver pulse
R: Inverted
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 1/9
http://www.m-system.co.jp/
MODEL: RPPD
[8] POWER INPUT
FACTORY DEFAULT SETTING
AC Power
■ SETTINGS FOR PULSE INPUT
INPUT 1, 2
K: 85 – 132 V AC
(Operational voltage range 85 – 132 V, 47 – 66 Hz)
• Dry Contact
(CE not available)
Input
Semiconductor contact
DC Power
Filter
No filter
2 V
Detecting level 0 – 15 V
Hysteresis 0 – 5 V
S: 12 V DC
0.5 V
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
(Option /CE Not available)
• Voltage pulse
Input waveform
Input coupling
Input amplitude
Input offset
R: 24 V DC
Square wave
DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
V: 48 V DC
0.5 – 50 Vp-p
≤ 50 V
(Operational voltage range 48 V ± 10 % , ripple 10 % p-p max.)
Filter
No filter
(CE not available)
Detecting level 0 – 15 V
Hysteresis 0 – 5 V
Adjusted to 1/2
0.5 V
P: 110 V DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(CE not available)
• 5 V voltage pulse
Filter
No filter
No filter
• 12 V, 24 V voltage pulse
[9] OPTIONS (multiple selections)
Standards & Approvals
blank: Without CE
Filter
• 2-wire current pulse
ON current (H) 0–25 mA
OFF current (L) 0–25 mA
Filter
/CE: CE marking
14.5 mA
9.5 mA
No filter
Other Options
blank: none
/Q: Option other than the above (specify the specification)
■ SETTINGS FOR PULSE OUTPUT
INPUT 1, 2
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Output pulse width
50 msec.
/C02: Polyurethane coating
GENERAL SPECIFICATIONS
Construction: Plug-in
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
Housing material: Flame-resistant resin (black)
Isolation: Input 1 or input 2 or sensor exc. to output 1 or
output 2 to power
DIP SW1 & SW2: Used for input spec. setting
Input monitor LED
PL1: Red LED blinks according to input 1.
PL2: Red LED blinks according to input 2.
Excitation adjustment: 5 – 24 V DC
Input pulse sensing: DC coupled standard or AC coupled
Sensitivity adjustments: V
H
pot. for Hi level; V pot. for Lo
L
level
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 2/9
http://www.m-system.co.jp/
MODEL: RPPD
■ Voltage pulse waveform
INPUT SPECIFICATIONS
Excitation: Shortcircuit protection; approx. 440 mA at
shortcircuit
Volts
50V max.
Pulse width time requirement: ≥ 5 μsec.
The detecting levels shown below are default value. Refer to
the manual for adjustment.
■ Dry Contact
Amplitude
Vinp-p
DC Offset
t
Max. frequency: 100 kHz
Detecting Conditions
■Voltage pulse (example)
Exc. code: 1
Volts
Sensing: 5 V DC / 0.5 mA
Detecting level:
VH
VL
Amplitude
Vinp-p
OFF: ≥ 2.25 V / ≥ 8.2 kΩ
ON: ≤ 1.75 V / ≤ 5.3 kΩ
Sensitivity Level
Exc. code: 4
0V
Sensing: 12 V DC / 1.2 mA
t
Detecting level:
ON
OFF: ≥ 2.25 V / ≥ 2.3 kΩ
OFF
Input Monitor LED
ON: ≤ 1.75 V / ≤ 1.7 kΩ
■Dry contact (example)
Exc. code: 7
Sensing: 16 V DC / 2.4 mA
Volts
Detecting level:
Exc.
OFF: ≥ 2.25 V / ≥ 1 kΩ
VH
VL
Amplitude
Vinp-p
ON: ≤ 1.75 V / ≤ 0.8 kΩ
Sensing voltage means the excitation supply to the sensor
and the current value indicates that at shortcircuit.
Detecting level means the threshold used to determine ON
or OFF status of the pulses and the resistance values
indicated that of the sensor.
■ Voltage Pulse
0V
t
The voltage which remains across
the terminals with contact ON
Maximum frequency: 100 kHz
• Customised pulse: Specify DC offset and amplitude.
Waveform: Square or sine
OUTPUT SPECIFICATIONS
■ High Power Photo MOSFET Relay
Maximum frequency: 20 Hz
Input impedance: ≥ 10 kΩ
• Rise time: 5 msec.
Input amplitude: 0.5 – 50 Vp-p
Max. voltage between input terminals: 50 V
• 5 V, 12 V, 24 V Pulse
• Sink time: 3 msec.
Rating: 120 V AC or 120 V DC @ 200 mA (resistive load)
On resistance: 3 Ω
Waveform: Square or sine
■ Open Collector
Input impedance: ≥ 10 kΩ
Maximum frequency: 100 kHz
50 V DC @ 50 mA (resistive load)
Saturation voltage: 0.5 V DC
Detecting level
5 V Pulse: V
12 V / 24 V Pulse: V
(V – V ≥ 500 mV)
H
≥ 2.25 V, V
L
≤ 1.75 V
≤ 4.75 V
H
≥ 5.25 V, V
L
■ Voltage Pulse: Rating (5, 12 or 24 V) ±10 %
Maximum frequency: 100 kHz (50 kHz for 24 V)
Load resistance: ≥ 1.2 kΩ
H
L
■ Two-wire Current Pulse
Max. frequency: 100 kHz
Low level: ≤ 0.5 V
Input resistance: receiving resistor 100 Ω
Input range: 0 – 25 mA
■ RS-422 Line Driver Pulse: Conforms to RS-422
Output current: ±20 mA
Hi/Lo level: ≤ 9.5 mA for Lo, ≥ 14.5 mA for Hi
■ RS-422 Line Driver Pulse
Maximum frequency: 100 kHz
Receiver: Conforms to RS-422
(No receiving resistor incorporated)
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 3/9
http://www.m-system.co.jp/
MODEL: RPPD
OUTPUT PULSE WIDTH
■ Equal to the input: Output waveforms have the same
period and duty ratio as those of input waveforms (when DC
coupled).
■ One-shot Output
This unit detects a pulse sink and outputs [input pulse width
±20 %]; 50 msec. standard
Note: 2 types of one-shot detection are available: pulse rise
or sink. Refer to the table on the "Output Logic" section and
specify when ordering.
Optional pulse width: 30 μsec. – 300 msec.
INSTALLATION
Power consumption
•AC: Approx. 5.5 VA
•DC: Approx. 3.3 W (140 mA at 24 V)
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 200 g (0.44 lb)
PERFORMANCE
Response time
1 - 4 μsec. delay occurs when the pulse rises and falls.
• Open collector: The delay could be much longer for certain
types of load.
• High power photo MOSFET relay: The output is delayed by
10 msec. at the rise, by 3 msec. at the fall.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 4/9
http://www.m-system.co.jp/
MODEL: RPPD
EXTERNAL VIEW
Note: This unit is factory calibrated according to the Ordering Information. If you need to change hardware setting, refer to the
instruction manuals of the transmitter.
SW1
Sensor Excitation Adj.
SW2
Sensitivity Adj. (VH)
(front cover open)
Sensitivity Adj. (VL)
Input Monitor LED PL1
Input Monitor LED PL2
There is no need of hardware adjustment
for RS-422 line driver pulse input.
Unnecessary switches or LEDs are not provided.
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 5/9
http://www.m-system.co.jp/
MODEL: RPPD
OUTPUT LOGIC
Applicable for both Output 1 and 2.
VOLTAGE PULSE,
INPUT WAVEFORM
2-WIRE CURRENT PULSE or
RS-422 LINE DRIVER PULSE
DRY CONTACT
H
OFF
OUTPUT WAVEFORM
L
ON
H
H
No pulse width conversion
L
L
One-shot, detecting input pulse rise
H
H
Non
Inverted
L
L
*
*
*
*
One-shot, detecting input pulse drop
H
H
L
L
VOLTAGE PULSE
or
H
H
No pulse width conversion
RS-422 LINE DRIVER PULSE
L
L
One-shot, detecting input pulse rise
H
H
Inverted
L
L
One-shot, detecting input pulse drop
H
H
L
L
OFF
OFF
No pulse width conversion
ON
ON
One-shot, detecting input pulse rise
OFF
OFF
Non
Inverted
ON
ON
One-shot, detecting input pulse drop
OFF
OFF
OPEN COLLECTOR
or
ON
ON
OFF
OFF
POWER PHOTO MOSFET RELAY
No pulse width conversion
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
One-shot, detecting input pulse rise
Inverted
One-shot, detecting input pulse drop
The pulse width in one-shot means the bold lined section of a pulse waveform.
*Pulse rise for RS-422 line driver pulse can not be detected.
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 6/9
http://www.m-system.co.jp/
MODEL: RPPD
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
8
7
6
5
4
2–
4.5 (.18) dia.
MTG HOLE
25 (.98) deep
9
3
2
10 11
1
11
–M3.5
SCREW
50 (1.97)
107 (4.21)
136 (5.35)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 7/9
http://www.m-system.co.jp/
MODEL: RPPD
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
INPUT
MON.
VH VL
Isolation
*
Waveform
Shaper
Output
Driver
One-Shot
+
–
3
4
1
2
+
–
INPUT 1
OUTPUT 1
INPUT MON.
*
Waveform
Shaper
Output
Driver
One-Shot
+
–
5
6
9
10
11
7
+
INPUT 2
OUTPUT 2
POWER
–
Excitation
Supply
U(+)
V(–)
SENSOR EXC.
VOLTAGE
ADJ.
8
Base Socket
* Provided only when the one-shot output is specified.
Note 1: With 24V excitation and dry contact input, the voltage across the terminals
3 – 4, 5 – 6, divided in the waveform shaper, is of approx. 16V.
Note 2: Not negative common in case of RS-422 line driver pulse output
or power photo MOSFET relay output.
Input Connection Examples
Output Connection Examples
■ Dry Contact
■ 2-Wire Current Pulse
• Built-in Excitation
■ Open Collector
■ Voltage Pulse
100
Ω
+
–
3
4
5
6
9
–
+
–
3
4
5
6
9
+
–
+
–
+
–
+
–
1
2
+
–
+
–
1
2
+
–
+
–
2-WIRE
PICK-UP
+
–
–
+
10
11
10
11
2-WIRE
PICK-UP
100
Ω
Vsns
Vsns
PWR
+
10kΩ
■ Power Photo MOSFET Relay
• AC Powered
■ RS-422 Line Driver Pulse
■ Voltage Pulse
• External DC Supply
100
Relay or
Counter Coil
+
–
+
–
+
–
+
–
1
2
+
–
+
–
1
Ω
+
–
3
4
5
6
9
3
–
+
2-WIRE
PICK-UP
Varistor or Spark
Quenching Circuit
LOAD
2
4
DC SUPPLY
10
11
U
+
–
• DC Powered
+
–
–
+
Relay or
Counter Coil
1
5
6
9
–
+
2-WIRE
PICK-UP
Vsns
Spark Quenching
Diode
PWR
LOAD
2
DC SUPPLY
100
Ω
+
–
■ RS-422 LINE DRIVER PULSE INPUT
Isolation
*
RS-422
Receiver
Output
Driver
One-Shot
+
–
+
–
3
4
5
6
1
2
+
A
A
B
B
OUTPUT 1
OUTPUT 2
POWER
–
*
RS-422
Receiver
Output
Driver
One-Shot
10
11
7
+
–
U(+)
V(–)
ROTARY
ENCODER
8
Base Socket
* Provided only when the one-shot output is specified.
Note 1: Sensor excitation not provided for RS-422 line driver pulse input.
Note 2: Not negative common in case of RS-422 line driver pulse output
or power photo MOSFET relay output.
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 8/9
http://www.m-system.co.jp/
MODEL: RPPD
Specifications are subject to change without notice.
RPPD SPECIFICATIONS
ES-1693 Rev.20 Page 9/9
http://www.m-system.co.jp/
RPPD-AA7NM1N-K 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| RPPD-AA7NM1N-S | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NM1R-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NM3N-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NM3R-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NN1N-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NN1N-S | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NN1R-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NN3N-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NN3R-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
| RPPD-AA7NP1N-K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
|
RPPD-AA7NM1N-K 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
