SES-261-V/E2
更新时间：2024-10-29 22:49:02
品牌：MSYSTEM
描述：Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR
概述
数据手册SES-261-V/E2 概述
Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR
SES-261-V/E2 数据手册
通过下载SES-261-V/E2数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: SES
Plug-in Signal Conditioners M-UNIT
[3] OUTPUT
Current
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
HIGH/LOW SELECTOR
(isolated)
Functions & Features
• Monitoring two DC input signals and transmitting an
output signal proportional to the higher or lower input
• LCD meter indicates the selected input signals
(engineering unit display selectable)
• Simple loop test output (0 % and 100 %)
• Isolation up to 2000 V AC
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
5W: -5 – +5 V DC (Load resistance 1000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
• High-density mounting
Typical Applications
• Selecting greater flow, pressure, etc. for control
• Heating control by multiple T/C’s on a furnace
50
(1.97)
80
(3.15)
[4] POWER INPUT
AC Power
B: 100 V AC
127
(5)
C: 110 V AC
mm (inch)
D: 115 V AC
F: 120 V AC
G: 200 V AC
MODEL: SES–[1][2][3]–[4][5]
H: 220 V AC
J: 240 V AC
DC Power
ORDERING INFORMATION
• Code number: SES-[1][2][3]-[4][5]
Specify a code from below for each [1] through [5].
(e.g. SES-1AA-B/E2Q)
S: 12 V DC
R: 24 V DC
V: 48 V DC
P: 110 V DC (Not selectable with Option /E2.)
• Special output range (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
[5] OPTIONS (multiple selections)
LCD Meter (after selection)
blank: Without
[1] SELECTING FUNCTION
1: Low input
/E: With (0.0 - 100.0 % display)
/E2: With (in engineering unit with backlight and the
simple loop test output)
2: High input
Other Options
[2] INPUT
Current
blank: none
/Q: Option other than the above (specify the specification)
A: 4 – 20 mA DC (Input resistance 250 Ω)
B: 2 – 10 mA DC (Input resistance 500 Ω)
C: 1 – 5 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Voltage
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
SES SPECIFICATIONS
ES-1646 Rev.3 Page 1/4
http://www.m-system.co.jp/
MODEL: SES
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
INSTALLATION
Power input
•AC: Operational voltage range: rating ±10 %, 50/60 ±2 Hz,
approx. 2 VA
/C02: Polyurethane coating
/C03: Rubber coating
(approx. 3 VA with Option /E2)
TERMINAL SCREW MATERIAL
/S01: Stainless steel
•DC: Operational voltage range: rating ±10 %, or 85 – 150 V
for 110 V rating ripple 10 %p-p max.
approx. 2.5 W (110 mA at 24 V; approx. 3.5 W with Option
/E2)
GENERAL SPECIFICATIONS
Construction: Plug-in
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
Weight: 400 g (0.88 lb)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -10 to +120 % at 1 – 5 V
Selecting operation: Automatic
PERFORMANCE in percentage of span
Accuracy: ±0.2 %
Display accuracy: ± (0.2 % of FS + 1 digit)
Simple loop test output setting accuracy: ±0.5 %
Selecting sensitivity: 0.5%
Simple loop test output: 0 % and 100 % signal simulated by
selecting the front switch positions. (Only for option code
/E2)
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
■ DISPLAY (LCD meter)
• Option code: /E
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)
(No scaling)
• Option code: /E2
LCD digital display: Engineering unit
Display scaling: -10000 – +10000
Decimal position: 10-1 - 10-4 or no decimal point
Engineering unit: %, μV, mV, V, mA, A, °C, °F, Ω, DEG K,
mHz, Hz, kHz, VAC, AAC, mg, g, kg, t, rpm or rps selectable
Back light: Green at normal, red at loop test output enable
Factory setting: scaling 0.00 - 100.00, unit: %
INPUT SPECIFICATIONS
■ DC Current:
Shunt resistor attached to the input terminals (0.5 W)
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 15 V max.
■ DC Voltage: -10 – +12 V DC
Minimum span: 5 mV
Offset: Max. 1.5 times span
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
SES SPECIFICATIONS
ES-1646 Rev.3 Page 2/4
http://www.m-system.co.jp/
MODEL: SES
EXTERNAL VIEW
OPTION /E2
LCD Meter
NEXT Key
Loop Test Selector
ENTER Key
Top
: 0% fixed
Middle : 100% fixed
Bottom : Cancel
(normal operating mode)
EXTERNAL DIMENSIONS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–M3.5
SCREW
50 (1.97)
107 (4.21)
127 (5)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
TERMINAL ASSIGNMENTS unit: mm (inch)
INPUT RESISTOR
(model: REM)
6
5
4
3
7
8
1
2
Input shunt resistor attached
for current input.
SES SPECIFICATIONS
ES-1646 Rev.3 Page 3/4
http://www.m-system.co.jp/
MODEL: SES
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
**
Isolation
Output
Driver
+
–
+
–
+
–
Selector
1
2
3
4
5
6
*
*
INPUT 1
INPUT 2
R
R
OUTPUT
POWER
***
LOOP TEST
SELECTOR
U(+)
V(–)
7
8
Base Socket
*
Input shunt resistor attached for current inputs.
** Option /E, E2
*** Option /E2
Specifications are subject to change without notice.
SES SPECIFICATIONS
ES-1646 Rev.3 Page 4/4
http://www.m-system.co.jp/
SES-261-V/E2 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| SES-261-V/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-B | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-B/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-B/E2 | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-B/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-C | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-C/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-C/E2 | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-C/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
| SES-262-H | MSYSTEM | Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR | 获取价格 |
|
SES-261-V/E2 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
