W2DYS-24BB-P [MSYSTEM]
Space-saving Dual Output Signal Conditioners Mini-MW Series;
| 型号： | W2DYS-24BB-P |
| 厂家： | 
M-SYSTEM |
| 描述： | Space-saving Dual Output Signal Conditioners Mini-MW Series |
| 文件： | 总3页 (文件大小：111K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: W2DYS
Space-saving Dual Output Signal Conditioners
[1] OUTPUT 1
Current
Mini-MW Series
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
CURRENT LOOP SUPPLY
(isolated, isolator usable)
Functions & Features
• Powers a 4 – 20 mA DC current loop
• Short circuit protection
• Applicable to smart transmitters
Typical Applications
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 1000 Ω min.)
4: 0 – 10 V DC (Load resistance 10 kΩ min.)
5: 0 – 5 V DC (Load resistance 5000 Ω min.)
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
• Various 2-wire transmitters
• Isolation application (4 – 20 mA input)
29.5 (1.16)
Model
88.5
(3.49)
[2] OUTPUT 2
Y: None
ZERO
SPAN
Current
124
(4.88)
ZERO
A: 4 – 20 mA DC (Load resistance 350 Ω max.)
B: 2 – 10 mA DC (Load resistance 700 Ω max.)
C: 1 – 5 mA DC (Load resistance 1400 Ω max.)
D: 0 – 20 mA DC (Load resistance 350 Ω max.)
E: 0 – 16 mA DC(Load resistance 430 Ω max.)
F: 0 – 10 mA DC (Load resistance 700 Ω max.)
G: 0 – 1 mA DC (Load resistance 7000 Ω max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
SPAN
mm (inch)
MODEL: W2DYS–24[1][2]-[3][4]
ORDERING INFORMATION
• Code number: W2DYS-24[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. W2DYS-24A6-M2/CE/Q)
Same range availability as Output 1
• Special output ranges (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
[3] POWER INPUT
AC Power
M: 85 – 264 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
Note: If one of the outputs should be a current range,
specify it for the Output 1 to allow a greater load.
(Select ‘/N’ for ‘Standards & Approvals’ code.)
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
(90 – 264 V for UL)
SUPPLY OUTPUT
24: 24 V DC
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
R2: 11 – 27 V DC
INPUT
Current
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
P: 110 V DC
4 – 20 mA DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(110 V ±10 % for UL)
W2DYS SPECIFICATIONS
ES-5525 Rev.11 Page 1/3
http://www.m-system.co.jp/
MODEL: W2DYS
Minimum span: 5 mV
[4] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
Offset: ≤ 1.5 times span
Load resistance: Output drive 1 mA max.; at ≥0.5 V
/CE: CE marking
/UL: UL approval, CE marking
Other Options
INSTALLATION
Power Consumption
blank: none
•AC:
/Q: Option other than the above (specify the specification)
Approx. 5 VA at 100 V
Approx. 6 VA at 200 V
Approx. 7 VA at 264 V
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
•DC: Approx. 3 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 200 g (0.44 lb)
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
TERMINAL SCREW MATERIAL
/S01: Stainless steel (UL not available)
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
GENERAL SPECIFICATIONS
Construction: Plug-in
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
Supply output: ±3 % over voltage range
Output signal: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
1 to output 2 to power to ground)
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Overrange output: Approx. -10 to +120 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Adjustable individually for each output 1 and output 2.
STANDARDS & APPROVALS
EU conformity:
EMC Directive
SUPPLY OUTPUT
EMI EN 61000-6-4
(across the terminals 1 – 5)
Output voltage: 24 – 28 V DC with no load
18 V DC min. at 20 mA
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Current rating: ≤ 22 mA DC
• Shortcircuit Protection
Installation Category II
Pollution Degree 2
Current limited: 30 mA max.
Protected time duration: No limit
Input or output 1 or output 2 to power input:
Reinforced insulation (300 V)
Input to output 1 to output 2: Basic insulation (300 V)
RoHS Directive
INPUT SPECIFICATIONS
■ DC Current: Input resistors incorporated
Approx. 300 Ω (50 Ω as receiving resistor, 250 Ω across the
monitor terminals)
EN 50581
Approval:
UL/C-UL nonincendive Class I, Division 2,
Groups A, B, C, and D
(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)
UL/C-UL general safety requirements
(UL 61010-1, CAN/CSA-C22.2 No.61010-1)
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 15 V max. for Output 1;
7 V max. for Output 2
■ DC Voltage: 0 – 12 V DC (up to 10 V for Output 2)
W2DYS SPECIFICATIONS
ES-5525 Rev.11 Page 2/3
http://www.m-system.co.jp/
MODEL: W2DYS
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
3
2
5
1
4
6
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
9
8
7
11–M3
SCREW
11 10
22 (.87)
29.5 (1.16)
21.5 (.87) 10 (.39)
84 (3.31)
114 (4.49)
[4 (.16)]
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
Z
S
Isolation
Low Drift
Amplifier
Output
Driver
+
–
+
+
–
1
2
5
4
7
8
50Ω
INPUT
OUTPUT 1
2-WIRE XMTR
PWR SUPPLY
S
Output
Driver
250Ω
+
–
3
6
–
Current
Limiter
OUTPUT 2
POWER
MONITOR V
1 – 5V DC
+
10 U(+)
11 V(–)
Base Socket
Note: The section enclosed by broken line is only with 2nd output option.
■ When Used as DC Supply
2-WIRE
TRANSMITTER
■ When Used as Isolator
–
+
–
+
+
–
1
2
5
4
1
2
5
4
50Ω
50Ω
INPUT
+
250Ω
250Ω
Specifications are subject to change without notice.
W2DYS SPECIFICATIONS
ES-5525 Rev.11 Page 3/3
http://www.m-system.co.jp/
相关型号：
W2DYS-24BB-P/CE
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-P/Q
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-P/UL
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R/CE
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R/Q
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R/UL
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R2
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R2/CE
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R2/Q
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BB-R2/UL
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
W2DYS-24BC-M
Space-saving Dual Output Signal Conditioners Mini-MW SeriesWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
©2020 ICPDF网 联系我们和版权申明