W2XF-Z1V2V2-R/Q [MSYSTEM]

Space-saving Dual Output Signal Conditioners Mini-MW Series;


型号：	W2XF-Z1V2V2-R/Q
厂家：	M-SYSTEM
描述：	Space-saving Dual Output Signal Conditioners Mini-MW Series
文件：	总4页 (文件大小：115K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: W2XF

(Configurator software is used to change the input type and

precise range.)

Space-saving Dual Output Signal Conditioners

Mini-MW Series

[2] OUTPUT 1

Current

LINEARIZER

(PC programmable)

Z1: Range 0 – 20 mA DC

Voltage

Functions & Features

• Accepting non-linear input and providing a linearized

output, proportional to the process variables

• 101-point calibration

V2: Range -10 – +10 V DC

V3: Range -5 – +5 V DC

• PC programmable

• High-density mounting

[3] OUTPUT 2

Same range availability as Output 1

Typical Applications

Y: None

• V-notch weir

(Configurator software is used to change output over the

described range of the selected suffix code.

For changing between suffix codes, set the Output Range

Selector on the side of unit before software adjustment.)

• Gas analyzer

• Irregular-shaped tank level input for volume calculation

• Square root extracting for DP transmitter

[4] POWER INPUT

29.5 (1.16)

AC Power

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

88.5

(3.48)

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

124

(4.88)

[5] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE

mm (inch)

Other Options

MODEL: W2XF–[1][2][3]-[4][5]

blank: none

/Q: Option other than the above (specify the specification)

ORDERING INFORMATION

• Code number: W2XF-[1][2][3]-[4][5]

Specify a code from below for each [1] through [5].

(e.g. W2XF-S2Z1V3-M2/N/Q)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

• Input range (e.g. 1 – 5 V DC)

/C02: Polyurethane coating

• Output 1 range (e.g. 4 – 20 mA DC)

• Output 2 range (e.g. 1 – 5 V DC)

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

• Specify the specification for option code /Q

(e.g. /C01/S01/SET)

EX-FACTORY SETTING

Note: If one of the outputs should be a current range,

specify it for the Output 1 to allow a greater load.

/SET: Preset according to the Ordering Information Sheet

(No. ESU-5507)

[1] INPUT

Current

RELATED PRODUCTS

• PC configurator software (model: W2CFG)

Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω)

Voltage

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

S1: Range -1 – +1 V DC (Input resistance 1 MΩ min.)

S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)

W2XF SPECIFICATIONS

ES-5507 Rev.4 Page 1/4

http://www.m-system.co.jp/

MODEL: W2XF

cable types.

maintained.

Load resistance: Output drive 12 V max. for Output 1; 7 V

max. for Output 2

GENERAL SPECIFICATIONS

Construction: Plug-in

(e.g. 4 – 20 mA: 600 Ω [12 V ÷ 20 mA])

If not specified, the output range is 4 – 20 mA DC.

■ DC Voltage

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Code V2 (wide spans)

Operational range: -11.5 – +11.5 V DC

Minimum span: 1 V

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Overrange output: -15 to +115 %

Code V3 (narrow spans)

Operational range: -6 – +6 V DC

Minimum span: 0.5 V

(Negative current output is not available.)

Zero adjustment: -5 to +5 % (PC programming)

Span adjustment: 95 to 105 % (PC programming)

Programming: Downloaded from PC; input range, output

range, zero and span,

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

maintained.

Load resistance: Output drive 1 mA max.

(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])

If not specified, the output range is shown below.

V2: 0 – 10 V DC

response time, linearization table, simulating output, etc.

Linearization: 101 points max. within the range of

-15 – +115 % input or output; represented as percentage of

full-scale (No table setting is done at shipping. [gain = 1])

Status indicator LED: Tri-color (green/amber/red) LED;

Blinking patterns indicate operation status of the

transmitter.

V3: 1 – 5 V DC

INSTALLATION

Configurator connection: 2.5 dia. miniature jack;

RS-232-C level

Power Consumption

•AC:

Approx. 5 VA at 100 V

Approx. 6 VA at 200 V

INPUT SPECIFICATIONS

■ DC Current: Input resistor incoporated

(If not specified, the input range is 4 – 20 mA DC.)

Input range: 0 – 50 mA DC

Approx. 7 VA at 264 V

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

Minimum span: 2 mA

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

■ DC Voltage

Code S1 (narrow spans)

PERFORMANCE in percentage of span

Overall accuracy:

Input range: -1 – +1V DC

Minimum span: 100 mV

Input accuracy + output accuracy [gain ≤ 1]

(inp. accuracy + out. accuracy) × gain [gain > 1]

Inversely proportional to the span.

See CALCULATION EXAMPLES OF OVERALL ACURACY.

• Input accuracy: (% of max. input range)

-1 – +1 V : ±0.01 %

Code S2 (wide spans)

Input range: -10 – +10 V DC

Minimum span: 1 V

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

If not specified, the input range is shown below.

S1: 0 – 100 mV DC

-10 – +10 V : ±0.01 %

0 – 50 mA : ±0.02 %

S2: 1 – 5 V DC

• Output accuracy: ±0.04 % of max. output range

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span

at -5 to +55°C [23 to 131°F]

OUTPUT SPECIFICATIONS

■ DC Current

Response time: (0 – 90 %)

Standard: ≤ 500 msec.

Operational range: 0 – 23 mA DC

Minimum span: 1 mA

Fast: ≤ 25 msec.

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

W2XF SPECIFICATIONS

ES-5507 Rev.4 Page 2/4

http://www.m-system.co.jp/

MODEL: W2XF

Dielectric strength: 2000 V AC @1 minute (input to output

1 to output 2 to power to ground)

CALCULATION EXAMPLES OF OVERALL ACCURACY

[Example] Input Type -10 – +10 V, Input Range 1 – 5 V,

Output Type 0 – 20 mA, Output Range 4 – 20 mA

Max. Input Range (20 V) ÷ Span (4 V) × 0.01 % = 0.05 %

Max. Output Range (20 mA) ÷ Span (16 mA) × 0.04 %

= 0.05 %

Overall accuracy = 0.05 + 0.05 = ±0.10 %

EXTERNAL VIEW

FRONT VIEW

SIDE VIEW

LED1 (LD1)

Output 1

Configuration DIP SW

LED2 (LD2)

1 2 3 4

LED3 (LD3)

OFF

Configurator Jack

Output 2

Configuration DIP SW

1 2 3 4

SW2

SW1

OFF

*Provided only for two-output type.

Refer to the instruction manual for detailed procedures.

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

6 (.23)

DIN RAIL

35mm wide

2–

4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

11–M3

SCREW

11 10

22 (.87)

29.5 (1.16)

21.5 (.87) 10 (.39)

84 (3.31)

114 (4.49)

[4 (.16)]

• When mounting, no extra space is needed between units.

W2XF SPECIFICATIONS

ES-5507 Rev.4 Page 3/4

http://www.m-system.co.jp/

MODEL: W2XF

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS

DIP SW

Isolation

24.9Ω

Output

Driver

–

CURRENT

(Z1)

OUTPUT 1

–

Digital

Computation

Circuit

Low Drift

Amplifier

–

VOLTAGE

(S1, S2)

DIP SW

Isolation

Output

Driver

OUTPUT 2

POWER

–

U(+)

V(–)

CONFIGURATOR

JACK

Base Socket

Remark: The section enclosed by broken line is only with 2nd output option.

Specifications are subject to change without notice.

W2XF SPECIFICATIONS

ES-5507 Rev.4 Page 4/4

http://www.m-system.co.jp/