WL40EW2F-S/Q [MSYSTEM]
Wireless I/O WL40F Series WIRELESS GATEWAY;
| 型号： | WL40EW2F-S/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Wireless I/O WL40F Series WIRELESS GATEWAY 无线 |
| 文件： | 总7页 (文件大小：575K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: WL40EW2F
Wireless I/O WL40F Series
FUNCTIONS & FEATURES
This unit
• Incorporates 900MHz band wireless module with RS-485
transparent type, which can communicate using Modbus-
RTU protocol.
WIRELESS GATEWAY
Modbus/TCP (Ethernet), Modbus-RTU Transparent 900MHz
Band Wireless Device (parent device)
• Converts Modbus-RTU (RS-485) and Modbus/TCP
(Ethernet) protocol.
• Incorporates the module compliant with FCC Part 15, and
can be used only in the United States.
60 (2.36)
[260
(10.24)]
RELATED PRODUCTS
For related products of wireless device, refer to M-System's
web site.
Maintenance software
Maintenance console: MH920 Console International (model:
MH920CI) (OKI)
155 (6.10)
mm (inch)
(Maintenance software is downloadable at M-System’s web
site.)
Coaxial cable
MODEL: WL40EW2F-[1][2]
• 7.5 m extension cable for rooftop antenna (model: CX-
SAC0SAD0Q0750) (OKI)
Using 7.5 m coaxial cable for extension decreases
transmission distance.
ORDERING INFORMATION
• Code number: WL40EW2F-[1][2]
Specify a code from below for each [1] and [2].
(e.g. WL40EW2F-R/E/Q)
GENERAL SPECIFICATIONS
Connection
• Specify the specification for option code /Q
(e.g. /C01)
Wireless network: SMA coaxial connector
Power supply: Tension clamp (Front Twinconnection)
Applicable wire size: 0.2 - 2.5 mm
2, stripped length: 10 mm
[1] POWER INPUT
DC Power
Ethernet: RJ-45 Modular Jack
Maintenance: Mini USB type B female connector
Housing material: Flame-resistant resin
Isolation: Power supply to Ethernet to FE1 to antenna
connector
S: 12 V DC
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
Switch: IP Reset
Refer to the instruction manual for details.
Indicator LED: Power
[2] OPTIONS (multiple selections)
Antenna
/S: Sleeve antenna
COMMUNICATION
■ Common spec.
/E: Rooftop antenna
Other Options
Modbus protocol
blank: none
Protocol: Modbus/TCP
/Q: Option other than the above (specify the specification)
Data: RTU (Binary)
Port No.: 502
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Max. number of socket connections: 8
IP address: 192.168.0.1 (factory setting);
Selectable with web browser
■ Ethernet
/C02: Polyurethane coating
/C03: Rubber coating
Communication Standard: IEEE 802.3u
Transmission: 10BASE-T, 100BASE-TX
Baud rate: 10/100 Mbps (Auto Negotiation function)
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 1/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
Transmission media: 10BASE-T (STP, Category 5) 100BASE-
TX (STP, Category 5e)
STANDARDS & APPROVALS
Module conforming to FCC Part 15 incorporated
Max. length of fieldbus segment: 100 meters
Ethernet indicator LED: Link, Link100
WIRELESS SPECIFICATIONS
Communication Standard: IEEE 802.15.4g
Frequency: 900MHz band (902 - 928 MHz)
Max. Transmission power: 20mW
Bandwidth: 400 kHz
Modulation: GFSK
Baud rate: Max. 100 kbps
Channels: 1 to 43ch
Security: 128bit AES
Indicator LEDs: 920Run, 920Link
Number of child devices: Max. 100
Protocol: Modbus-RTU
Communication module: Coordinator module incorporated
(Oki Electric Industry Co., Ltd. )
Radio parameters setting: by Web browser
Max. transmission distance (optical): Approx. 1 km
Antenna
•Sleeve antenna (Model: MH920-ANT-F (S))
Indoor use
Non-waterproof
Non-directional
Gain: 3.0dBi max.
•Rooftop antenna (Model: MH920-ANT-F (R))
Outdoor/indoor use
Cable length: 2.5 m
Waterproof performance: IPx6 (except connector)
Non-directional
Gain: 2.0dBi max.
INSTALLATION
Current consumption:
24 V DC: ≤ 90 mA
12 V DC: ≤ 170 mA
Operating temperature: -20 to +60°C (-4 to +140°F)
Operating humidity: 10 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: DIN rail
Weight
Unit: Approx. 270 g (0.60 lb)
Sleeve antenna (standard): 27 g (0.95 oz)
Rooftop antenna: 52 g (1.83 oz)
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(power input to Ethernet or FE1 to antenna connector)
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 2/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
WEB BROWSER SETTING
With Web browser, settings shown below are available.
Refer to the operating manual (EM-9080-B) for detailed settings.
■ TCP / IP SETTING
ITEM
SETTING RANGE
DEFAULT
192.168.0.1
255.255.255.0
0.0.0.0
IP address
Subnet mask
Default gateway
1.0.0.0 – 223.255.255.255
224.0.0.0 – 255.255.255.255
0.0.0.0 – 255.255.255.255
■ MODBUS / TCP SETTING
ITEM
SETTING RANGE
1 – 65535
DEFAULT
Port
502
Modbus exception response
Not return 06 (BUSY), 0B (ERROR) /
Return 06 (BUSY), 0B (ERROR)
Return 06 (BUSY), 0B (ERROR)
Communication timeout
1 – 60 (min.)
1 (min.)
■ WIRELESS SETTING
ITEM
SETTING RANGE
DEFAULT
0000
PAN ID (group number)
Radio channel number
Network name
0000 – FFFE (hexadecimal, 4 digits)
1 – 43ch
1ch
English one-byte characters within 16 characters
(one-byte space, “-”, “_”, “.”, “@” are usable.)
MH920
Encryption key
0000...0 – FFFF...F
(hexadecimal, 32 digits)
0000...0
Pre!x
2000:0000:0000:0000 – 3FFF:FFFF:FFFF:FFFF
0.16mW / 1mW / 20mW
2000:0000:0000:0000
20mW
Transmitter power output
Device type in a network,
Number of devices in a network
Child (!xed), 1 to 30 devices /
Child (!xed), 31 to 60 devices /
Child (!xed), 61 to 100 devices /
Child (!xed) + child (moving)
Child (!xed), 1 to 30 devices
Set network quality
Standard (recommended) /
Frequency of route switching and delay (higher) /
Frequency of route switching and delay (highest)
Standard (recommended)
Network join mode
V3-compatible mode / Fast join mode
None / Yes (polling type)
1.0 – 60.0 (sec.)
V3-compatible mode
Yes (polling type)
4.0 (sec.)
Packet !ltering
Filter timeout on polling
Setting mode of short address
Range mode: 1 device (max. multi drop number)
Range mode: 1 to 4 devices (max. multi drop number)
Range mode: 1 to 8 devices (max. multi drop number)
Range mode: 1 to 16 devices (max. multi drop number)
Range mode: 1 to 31 devices (max. multi drop number)
List mode
List mode
920Run timeout
0.0 – 3200.0 (sec.)
Once / Twice / Three times
Short address
5.0 (sec.)
Retry times before route switching
Short address list setting
MAC address list setting
Connection refusal list setting
Three times
—
—
—
MAC address
MAC address
* For version confirmation of communication module, refer to the operating manual (EM-9080-B).
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 3/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
EXTERNAL VIEW
■ FRONT VIEW
Status Indicator LED
Antenna Connector
Power
Link
Link100
920Link
920Run
Network Status Indicator LED
Maintenance Connector
CFG
Ethernet
RJ-45 Modular jack
Reset Switch
24V
0V
NC
NC
FE1
IP Reset
Connector for Power Input *
* Power input defers depending on the power input code you select.
TERMINAL ASSIGNMENTS
■ CONNECTORS FOR POWER INPUT
Unit side connector: MSTBV2,5/5-GF-5,08AU (Phoenix Contact)
Cable side connector: TFKC2,5/5-STF-5,08AU (Phoenix Contact)
• Power input code: R (24 V DC)
• Power input code: S (12 V DC)
ID FUNCTION
ID
24V
0V
FUNCTION
Power input 24 V
Power input 0 V
Not used
12V
0V
Power input 12 V
Power input 0 V
Not used
24V
0V
12V
0V
NC
NC
FE1
NC
NC
FE1
NC
NC
FE1
NC
NC
FE1
Not used
Not used
Power input earth
Power input earth
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 4/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
MODBUS FUNCTION CODES & SUPPORTED CODES
Modbus function codes are shown below.
■ DATA AND CONTROL FUNCTIONS
CODE
01
NAME
Read Coil Status
Digital output from the slave (read/write)
02
Read Input Status
Read Holding Registers
Read Input Registers
Force Single Coil
Status of digital inputs to the slave (read only)
General purpose register within the slave (read/write)
Collected data from the !eld by the slave (read only)
Digital output from the slave (read/write)
03
04
05
06
Preset Single Registers
Force Multiple Coils
Preset Multiple Registers
General purpose register within the slave (read/write)
Digital output from the slave (read/write)
15
16
General purpose register within the slave (read/write)
■ EXCEPTION CODES
CODE
06
NAME
Slave Device Busy
Device’s Modbus/TCP request queue is full.
11
Gateway Target Device Failed To Respond
Response from 900MHz band wireless device (child) is error, or response
timeout occurred.
Note: When 900 MHz band wireless device (child) returns an exception code other than the above, the exception code is directly transmit-
ted to upper devices.
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 5/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
EXTERNAL DIMENSIONS unit: mm (inch)
• With sleeve antenna
DIN RAIL
35mm wide
60 (2.36)
45 (1.77)
107 (4.21)
3 (.12)
[200 (7.87)]
• With rooftop antenna
ø3 (.12)
ø1.2 (.05)
8 (.31) Hex.
DIN RAIL
35mm wide
ø27
approx. 2500 (98.4)
(1.06)
107 (4.21)
20
(.79)
3 (.12)
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 6/7
http://www.m-system.co.jp/
MODEL: WL40EW2F
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
LED
Isolation
Two-way
wireless circuit
Communication
Circuit
To Other
Ethernet Devices
Antenna Connector
USB Connector
RJ-45 Modular Jack
24V
0V
*
Maintenance
Connector
Power Input
Control
Circuit
NC
NC
FE1
Reset Switch
* Power input defers depending on the power input code you select.
SYSTEM CONFIGURATION EXAMPLES
PC side as Modbus/Master communicates with child devices via wireless module using Modbus/TCP and RTU protocol,
and also communicates with slave devices in multi drop connection (RS-485).
LAN cable
(STP cable)
RS-485
Slave Device
Slave Device
MAX. 31
Slave Device
Wireless gateway
(model: WL40MW1F)
PC
Modbus/Master
Wireless gateway
(model: WL40EW2F)
Specifications are subject to change without notice.
WL40EW2F SPECIFICATIONS
ES-9080 Rev.0 Page 7/7
http://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明