WRPP-JNM-R [MSYSTEM]
Dual Output Plug-in Signal Conditioners W-UNIT;
| 型号： | WRPP-JNM-R |
| 厂家： | 
M-SYSTEM |
| 描述： | Dual Output Plug-in Signal Conditioners W-UNIT |
| 文件： | 总4页 (文件大小：130K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: WRPP
Dual Output Plug-in Signal Conditioners W-UNIT
[3] OUTPUT 2
A: Open collector (max. frequency 100 kHz)
K: 3.3 V pulse (max. frequency 1 MHz)
ENCODER SIGNAL DISTRIBUTOR
(rotary encoder use)
M: 5 V pulse (max. frequency 500 kHz)
N: 12 V pulse (max. frequency 100 kHz)
J: RS-422 line driver pulse (max. frequency 1 MHz)
Functions & Features
• Isolating two phase pulse input signals from a rotary
encoder and distributing them to two outputs (input
frequency = output frequency)
[4] OUTPUT LOGIC (both Input 1 & 2)
N: The same as the input
• Various outputs (open collector, voltage pulse, RS-422 line
driver pulse)
R: Inverted
• Can be used as a pulse isolator of two different I/O specs
• Converting RS-422 line driver pulse into an open collector
pulse
[5] POWER INPUT
AC Power
• Isolation up to 2000 V AC
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
• Maximum frequency of 1 MHz
47 – 66 Hz)
DC Power
72
(2.83)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
R2: 11 – 27 V DC
80
(3.15)
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)
(CE not available)
P: 110 V DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
136
(5.35)
mm (inch)
[6] OPTIONS
blank: none
MODEL: WRPP–[1][2][3][4]-[5][6]
/Q: With options (specify the specification)
ORDERING INFORMATION
• Code number: WRPP-[1][2][3][4]-[5][6]
Specify a code from below for each of [1] through [6].
(e.g. WRPP-JJJN-R/Q)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
• Specify the specification for option code /Q
(e.g. /C01/S01)
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
[1] INPUT
A1: Dry contact
GENERAL SPECIFICATIONS
Construction: Plug-in
K: 3.3 V pulse
C: 5 V pulse
Connection: M3.5 screw terminals
D: 12 V/24 V pulse
J: RS-422 line driver pulse
Screw terminal: Chromated steel (standard) or stainless
steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Input monitor LED: Available to check input pulse existence
Input pulse sensing: DC coupled
[2] OUTPUT 1
A: Open collector (max. frequency 100 kHz)
K: 3.3 V pulse (max. frequency 1 MHz)
M: 5 V pulse (max. frequency 500 kHz)
N: 12 V pulse (max. frequency 100 kHz)
J: RS-422 line driver pulse (max. frequency 1 MHz)
WRPP SPECIFICATIONS
ES-2222 Rev.3 Page 1/4
http://www.m-system.co.jp/
MODEL: WRPP
Max. frequency: 1 MHz
Output current: ±20 mA
INPUT SPECIFICATIONS
■ Dry Contact
Max. frequency: 100 kHz
Input requirements
INSTALLATION
Power Consumption
•AC:
Sensing: 5 V DC / 10 mA
Detecting level:
OFF: ≥ 3.0 V / ≥ 750 Ω
Approx. 4 VA at 100 V
Approx. 5 VA at 200 V
Approx. 6 VA at 240 V
•DC: Approx. 3 W
ON: ≤ 2.0 V / ≤ 333 Ω
Sensing voltage/current shows the excitation supply to the
input terminal and the current value at the time of
shortcircuit.
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Detecting level shows the threshold used to determine ON
or OFF status of the pulses and the resistance values of the
dry contact of that time.
Weight: 250 g (0.55 lb)
■ Voltage Pulse
Waveform: Square or sine
PERFORMANCE
•3.3 V Pulse
Response time delay
Max. frequency: 1 MHz
•3.3 or 5 V voltage pulse or RS-422 line driver pulse:
Approx. 0.15 - 0.5 μsec.
Input impedance: Approx. 8 kΩ 100 pF
Max. voltage between terminals (pulse): -10 – +15 V
Max. voltage between terminals (DC): -5 – +10 V DC
•12 V voltage pulse or open collector: 0.2 - 2 μsec.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
1 to output 2 to power to ground)
Detecting level: V
H
≥ 2.0 V, V ≤ 1.3 V
L
•5 V Pulse
Max. frequency: 500 kHz
Input impedance: Approx. 14 kΩ 100 pF
Max. voltage between terminals (pulse): -10 – +15 V
Max. voltage between terminals (DC): -5 – +10 V DC
STANDARDS & APPROVALS
EU conformity:
Detecting level: V
H
≥ 3.0 V, V ≤ 2.0 V
L
EMC Directive
•12 V, 24 V Pulse
EMI EN 61000-6-4
Max. frequency: 100 kHz
EMS EN 61000-6-2
Input impedance: Approx. 20 kΩ
Low Voltage Directive
EN 61010-1
Max. voltage between terminals (pulse): -30 – +50 V
Max. voltage between terminals (DC): -30 – +50 V DC
Installation Category II
Pollution Degree 2
Detecting level: V
H
≥ 7.0 V, V ≤ 5.0 V
L
■ RS-422 Line Driver Pulse
Maximum frequency: 1 MHz
Input or output 1 or output 2 to power input:
Reinforced insulation (300 V)
Input to output 1 to output 2: Basic insulation (300 V)
RoHS Directive
Receiver: Conforms to RS-422
(No receiving resistor incorporated)
EN 50581
OUTPUT SPECIFICATIONS
■ Open collector
Max. frequency: 100 kHz
Rating: 50 V DC @ 100 mA
Saturation voltage: 0.12 V DC
■ Voltage Pulse: Rating (3.3, 5 or 12 V) ±20 %
Max. frequency ; Load resistance (the lower value of either
this or the maximum frequency of the input signal)
3.3 V 1 MHz ; 660 Ω
5 V 500 kHz ; 1 kΩ
12 V 100kHz ; 2.4 kΩ
Low level: ≤ 0.5 V
■ RS-422 Line Driver Pulse: Conforms to RS-422
WRPP SPECIFICATIONS
ES-2222 Rev.3 Page 2/4
http://www.m-system.co.jp/
MODEL: WRPP
EXTERNAL VIEW
Input Monitor LED Phase B (Red)
Input Monitor LED Phase A (Green)
OUTPUT LOGIC
Applicable for both Output 1 and 2.
Voltage pulse
Input
Dry contact
RS-422 line driver pulse
H
OFF
Output
L
ON
H
H
Voltage pulse
Non-inverted
L
L
or
RS-422 line
H
H
driver pulse
Inverted
L
L
OFF
OFF
Non-inverted
Inverted
ON
ON
Open collector
OFF
OFF
ON
ON
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
7
14
6
5
12
4
3
2–4.5 (.18) dia.
MTG HOLE
25 (.98) deep
8
9
15 10
1
11
2
14–M3.5
SCREW
50 (1.97)
72 (2.83)
107 (4.21)
136 (5.35)
60 (2.36)
72 (2.83)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
WRPP SPECIFICATIONS
ES-2222 Rev.3 Page 3/4
http://www.m-system.co.jp/
MODEL: WRPP
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Output Circuit
Phase A
+
−
+
−
+
−
+
−
4
12
5
Isolation
PHASE A
OUTPUT 1
Input
Circuit
8
9
+
Output Circuit
Phase B
PHASE A
−
PHASE B
6
INPUT
Output Circuit
Phase A
1
Input
Circuit
PHASE A
10
15
+
11
2
PHASE B
OUTPUT 2
PHASE B
−
Output Circuit
Phase B
3
7
U(+)
POWER
14 V(−)
Base Socket
Input Connection Examples
Output Connection Examples
■ Dry Contact Input
■■ Open Collector Output
■ Voltage Pulse Output
■ RS-422 Line Driver Pulse Output
+
8
+
+
+
–
+
–
4
12
5
+
−
+
−
+
−
+
−
4
12
5
+
−
+
−
+
−
+
−
4
+
−
–
–
+
–
+
–
+
–
–
+
–
+
–
+
–
9
12
+
–
10
15
+
–
+
–
5
6
+
−
6
6
5V
1
1
+
–
+
–
500Ω
1
+
−
11
2
11
2
11
■ Voltage Pulse Input
+
–
+
–
2
3
+
−
3
3
+
–
8
9
+
–
10
15
■ RS-422 Line Driver Pulse Input
+
8
Phase A
Phase A
RS-422
Receiver
−
+
−
9
10
15
Phase B
Phase B
RS-422
Receiver
Specifications are subject to change without notice.
WRPP SPECIFICATIONS
ES-2222 Rev.3 Page 4/4
http://www.m-system.co.jp/
相关型号：
WRPP-JNM-R/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNM-R2
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNM-R2/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-M2
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-M2/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-P
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-P/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-R
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-R/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-R2
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-JNN-R2/Q
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
WRPP-KAA-M2
Dual Output Plug-in Signal Conditioners W-UNITWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MSYSTEM
©2020 ICPDF网 联系我们和版权申明