WRPPB-M7M5M7N-M2/Q
更新时间：2024-10-29 22:28:26
品牌：MSYSTEM
描述：Dual Output Plug-in Signal Conditioners W-UNIT
概述
数据手册WRPPB-M7M5M7N-M2/Q 概述
Dual Output Plug-in Signal Conditioners W-UNIT
WRPPB-M7M5M7N-M2/Q 数据手册
通过下载WRPPB-M7M5M7N-M2/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: WRPPB
Dual Output Plug-in Signal Conditioners W-UNIT
[2] OUTPUT 1
A: Open collector
K5: 3.3 V pulse, output impedance 50 Ω
K7: 3.3 V pulse, output impedance 75 Ω
M5: 5 V pulse, output impedance 50 Ω
M7: 5 V pulse, output impedance 75 Ω
Q7: 10 V pulse, output impedance 50 Ω
N: 12 V pulse, load resistance 600 Ω
J: RS-422 line driver pulse
ENCODER SIGNAL DISTRIBUTOR
(rotary encoder use, BNC connection)
Functions & Features
• Isolating two phase pulse input signals from a rotary
encoder and distributing them to two outputs (input
frequency = output frequency)
• Various outputs (open collector, voltage pulse, RS-422 line
driver pulse)
• Can be used as a pulse isolator of two different I/O specs
• Converting RS-422 line driver pulse into an open collector
pulse
[3] OUTPUT 2
Same range availability as Output 1
(Q7 not selectable)
• Maximum frequency of 1 MHz
• BNC connector
[4] OUTPUT LOGIC (both Input 1 & 2)
N: The same as the input
• Characteristic impedance 50Ω and 75Ω available
R: Inverted
(
)
50 1.97
[5] POWER INPUT
AC Power
(
)
80 3.15
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
DC Power
R: 24 V DC
(
)
123 4.84
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
P: 110 V DC
mm (inch)
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
MODEL: WRPPB–[1][2][3][4]-[5][6]
[6] OPTIONS
blank: none
ORDERING INFORMATION
• Code number: WRPPB-[1][2][3][4]-[5][6]
Specify a code from below for each of [1] through [6].
(e.g. WRPPB-A1K5K5N-M2/Q)
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• Specify the specification for option code /Q
(e.g. /C01/S01)
/C02: Polyurethane coating
/C03: Rubber coating
[1] INPUT
A1: Dry contact
TERMINAL SCREW MATERIAL
/S01: Stainless steel
K: 3.3 V pulse, input impedance approx. 8 kΩ 100 pF
K5: 3.3 V pulse, input impedance 50 Ω
K7: 3.3 V pulse, input impedance 75 Ω
C: 5 V pulse, input impedance approx. 14 kΩ 100 pF
C5: 5 V pulse, input impedance 50 Ω
C7: 5 V pulse, input impedance 75 Ω
D: 12 V/24 V pulse
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection
I/O: BNC connectors
(Recommended connector manufacturer: Hirose)
Power input: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
J: RS-422 line driver pulse
Housing material: Flame-resistant resin (black)
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 1/6
http://www.m-system.co.jp/
MODEL: WRPPB
Isolation: Input to output 1 to output 2 to power
Input pulse sensing: DC coupled
OUTPUT SPECIFICATIONS
■ Open collector
Max. frequency: 100 kHz
Rating: 50 V DC @ 100 mA
INPUT SPECIFICATIONS
■ Dry Contact
Saturation voltage: 0.12 V DC
■ Voltage Pulse (open voltage):
Rating (3.3, 5, 10 or 12 V) ±20 %
Max. frequency ; Load resistance (the lower value of either
this or the maximum frequency of the input signal)
3.3 V 1 MHz / Output code K5: 50 Ω, K7: 75Ω
5 V 500 kHz / Output code M5: 50 Ω, M7: 75Ω
10 V 200 kHz / 75Ω
Max. frequency: 100 kHz
Min. pulse width: ≥ 5 μs
Input requirements
Sensing: 5 V DC / 10 mA
Detecting level:
OFF: ≥ 3.0 V / ≥ 750 Ω
ON: ≤ 2.0 V / ≤ 333 Ω
12 V 100 kHz / 600 Ω
Sensing voltage/current shows the excitation supply to the
input terminal and the current value at the time of
shortcircuit.
(≥ 6 V @ 600 Ω load)
Low level: ≤ 0.5 V
■ RS-422 Line Driver Pulse: Conforms to RS-422
Max. frequency: 1 MHz
Detecting level shows the threshold used to determine ON
or OFF status of the pulses and the resistance values of the
dry contact of that time.
Output current: ±20 mA
■ Voltage Pulse
Waveform: Square or sine
INSTALLATION
Power Consumption
•3.3 V Pulse
Max. frequency: 1 MHz
•AC:
Min. pulse width: ≥ 0.5 μs
Approx. 4 VA at 100 V
Input impedance: Approx. 8 kΩ 100 pF
Max. voltage between terminals (pulse): -10 – +15 V
Max. voltage between terminals (DC): -5 – +10 V DC
Approx. 5 VA at 200 V
Approx. 6 VA at 240 V
•DC: Approx. 3 W
Detecting level: V
H
≥ 2.0 V, V ≤ 1.3 V
L
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 260 g (0.57 lb)
Input impedance: Approx. 50 Ω, 75 Ω
Max. voltage between terminals (pulse): -7 – +7.5 V
Max. voltage between terminals (DC): -5 – +10 V DC
Detecting level: V
H
≥ 1.5 V, V ≤ 0.75 V
L
•5 V Pulse
PERFORMANCE
Response time
Max. frequency: 500 kHz
Min. pulse width: ≥ 1 μs
•Lower value of I/O max. frequency is 1 MHz:
0.15 - 0.5 μsec.
Input impedance: Approx. 14 kΩ 100 pF
Max. voltage between terminals (pulse): -10 – +15 V
Max. voltage between terminals (DC): -5 – +10 V DC
•Lower value of I/O max. frequency is 500 kHz:
0.2 - 1.2μs
Detecting level: V
H
≥ 3.0 V, V ≤ 2.0 V
L
•Lower value of I/O max. frequency is less than 500 kHz:
0.2 - 2 μsec.
Input impedance: Approx. 50 Ω, 75 Ω
Max. voltage between terminals (pulse): -7 – +10 V
Max. voltage between terminals (DC): -5 – +7.5 V DC
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute (input to output 1
to output 2)
Detecting level: V
H
≥ 2.4 V, V ≤ 1.2 V
L
•12 V, 24 V Pulse
2000 V AC @ 1 minute (input or output 1 or output 2 to
power to ground)
Max. frequency: 100 kHz
Min. pulse width: ≥ 5 μs
Input impedance: Approx. 20 kΩ
Max. voltage between terminals (pulse): -30 – +50 V
Max. voltage between terminals (DC): -30 – +50 V DC
STANDARDS & APPROVALS
EU conformity:
Detecting level: V
H
≥ 7.0 V, V ≤ 5.0 V
L
EMC Directive
■ RS-422 Line Driver Pulse
Maximum frequency: 1 MHz
EMI EN 61000-6-4
EMS EN 61000-6-2
Receiver: Conforms to RS-422
Low Voltage Directive
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 2/6
http://www.m-system.co.jp/
MODEL: WRPPB
EN 61010-1
Measurement Category II
Pollution Degree 2
Input or output 1 or output 2 to power input:
Reinforced insulation (300 V)
Input to output 1 to output 2: Basic insulation (300 V)
RoHS Directive
EN 50581
EXTERNAL VIEW
Input Phase A
Input Phase B
Input Monitor LED
Phase B (Red)
INPUT
IN A
IN B
MONITOR
Input Monitor LED
Phase A (Green)
B
A
Output 1 Phase B
Output 2 Phase B
Output 1 Phase A
Output 2 Phase A
OUT 1A
OUT 1B
OUT 2A
OUT 2B
OUTPUT LOGIC
Applicable for both Output 1 and 2.
Voltage pulse
Input
Dry contact
RS-422 line driver pulse
H
OFF
Output
L
ON
H
H
Voltage pulse
Non-inverted
L
L
or
RS-422 line
H
H
driver pulse
Inverted
L
L
OFF
OFF
Non-inverted
Inverted
ON
ON
Open collector
OFF
OFF
ON
ON
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 3/6
http://www.m-system.co.jp/
MODEL: WRPPB
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
(
7.8 0.31
)
(
20 0.79
)
DIN RAIL
35mm wide
6
5
4
3
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–M3.5
SCREW
16 (.63)
(
103 4.06
)
(
40 1.57
)
(
50 1.97
)
(
123 4.84
)
[
(
3.3 .13
)]
(
50 1.97
)
11
0.43
(
)
• When mounting, no extra space is needed between units.
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 4/6
http://www.m-system.co.jp/
MODEL: WRPPB
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Output Circuit
Phase A
+
Isolation
PHASE A
−
Input
Circuit
+
PHASE A
−
OUTPUT 1
+
Output Circuit
Phase B
PHASE B
−
INPUT
Input
Circuit
+
PHASE B
−
Output Circuit
Phase A
+
PHASE A
−
OUTPUT 2
+
1
2
3
4
5
6
Output Circuit
Phase B
PHASE B
−
7
8
U (+)
POWER
V (−)
Base Socket
Input Connection Examples
• Dry Contact Input
Output Connection Examples
• Open Collector Output
• Voltage Pulse Output
• RS-422 Line Driver Pulse Output
PHASE A
PHASE A
PHASE B
PHASE A
PHASE B
PHASE A
PHASE A
+
–
PHASE B
PHASE B
PHASE A
PHASE B
PHASE B
+
–
5V
PHASE A
500Ω
+
–
PHASE B
• Voltage Pulse Input
+
PHASE A
–
PHASE B
• RS-422 Line Driver Pulse Input
PHASE A
PHASE A
RS-422
Receiver
250Ω
PHASE A
PHASE B
PHASE B
PHASE B
RS-422
250Ω
Receiver
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 5/6
http://www.m-system.co.jp/
MODEL: WRPPB
Specifications are subject to change without notice.
WRPPB SPECIFICATIONS
ES-2223 Rev.3 Page 6/6
http://www.m-system.co.jp/
WRPPB-M7M5M7N-M2/Q 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| WRPPB-M7M5M7N-P | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7N-R | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7N-R/Q | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7R-M2 | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7R-M2/Q | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7R-P | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7R-R | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5M7R-R/Q | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5NN-M2 | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
| WRPPB-M7M5NN-M2/Q | MSYSTEM | Dual Output Plug-in Signal Conditioners W-UNIT | 获取价格 |
|
WRPPB-M7M5M7N-M2/Q 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
