D1U54-D-1500-12-HC4C [MURATA]
民用设备,工业设备;
| 型号： | D1U54-D-1500-12-HC4C |
| 厂家： | 
muRata |
| 描述： | 民用设备,工业设备 |
| 文件： | 总9页 (文件大小：863K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
PRODUCT OVERVIEW
D1U54-D-1200-12-HxxC series are highly efficient 1500 watt, DC input front end power modules with a 12V main
output and a choice of 3.3V, 5V or 12VDC (30W max) standby rail.The power module is able to current share with up to
eight (8) other power modules of the same type operating in parallel or N+1 redundancy. The supplies may be hot
plugged, and include integral output isolation devices.
The power modules are fully protected from overload and overvoltage and are able to auto-recover from
overtemperature faults. A Status LED is provided on the front panel and additional control and status reporting is
provided by hardware logic signals and via a PMBus™ digital interface.
A low profile sub 1U height enclosure with power density of >35W/in3 make this an excellent choice for delivering
reliable, efficient power to servers, workstations, storage systems and other 12V distributed power systems
including direct operation from intermediate bus converters.
ORDERING GUIDE
Part Number
Internal MPN
M1900
Power Output
Main Output Standby Output
Airflow
D1U54-D-1500-12-HC4C
D1U54-D-1500-12-HA4C
D1U54-D-1500-12-HB4C
D1U54-D-1500-12-HC3C
D1U54-D-1500-12-HA3C
3.3V
5V
+1500W continuous output power (no
derating across full DC input range)
93% efficiency
M1897
M1903
M1901
M1898
Back to Front
1500W
-48 to -60Vdc
45°C
12V
12V
3.3V
5V
Front to Back
12V main output
3.3V; 5V or 12V Standby Output Options
1U height: 2.15" x 12.65" x 1.57"
> 35 Watts per cubic inch density
N+1 redundancy,hot plug/swap (up to 8
modules in parallel)
INPUT CHARACTERISTICS
Parameter
DC Input Voltage Operating Range
Turn-on Input Voltage
Turn-off Input Voltage
Maximum Current
Conditions
Min
-40
-39
-35
Max
-48/-60 -72
Units
Vdc
Typical
Ramp Up
Ramp Down
1500W, Vin = -48Vdc to -60Vdc
-40
-36
-41
-37
51
Active current sharing on 12V main
output; Integral ORing /isolation device
MOSFET
Internal cooling fan (variable speed)
Overvoltage, overcurrent,
overtemperature protection
PMBus™/I²C interface with LED status
indicators
Adc
Apk
Cold start between 0 to -48Vdc
200ms
50
100
DC Input Inrush Peak Current
-72Vdc
20% FL
50% FL
100% FL
Withstand Reversed input
cables; no internal/external fuse
failure
92
93
90
Efficiency (-48Vdc)
%
Reverse polarity protection
+40
+72
Vdc
RoHS compliant
Two Year Warranty
OUTPUT VOLTAGE CHARACTERISTICS
Output Voltage Parameter
Conditions
Min.
-1
Typical
12
Max. Units
Vdc
Voltage Set Point
Line & Load Regulation
Combined, measured at remote
20MHz Bandwidth
-40Vdc to -72Vdc DC input
+1.5
120
125A
30,000
%
mV P-P
A
Main 12V
Ripple & Noise1,2
Output Current
0
Load Capacitance
Voltage Set Point
Line & Load Regulation
μF
3.3
5.0
Vdc
Combined regulation
Ripple Voltage & Noise1,3 20MHz Bandwidth
3.14
0
3.46
3.3VSB
5VSB
120 mV P-P
Output Current
4
A
μF
Load Capacitance
Voltage Set Point
Line & Load Regulation
3,000
Vdc
4.76
0
5.24
w
/
/
/
Ripple Voltage & Noise1,3 20MHz Bandwidth
Output Current
120 mV P-P
4
A
μF
Load Capacitance
Voltage Set Point
3,000
12.0
Vdc
Line & Load Regulation
Ripple Voltage & Noise1,3 20MHz Bandwidth
Output Current
11.4
0
12.6
12VSB
120 mV P-P
2.5
1,000
A
μF
Available now at: www. murata-ps.com/en/3d/acdc.html
Load Capacitance
1 Ripple and noise are measured with 0.1 μF of ceramic capacitance and 10 μF of tantalum capacitance on each of the power
supply outputs. A short coaxial cable to the measurement ‘scope input, is used.
2 Minimum load 5A
3 Minimum load 0.25A
For full details go to
www.murata-ps.com/rohs
Test Certificate
and Test Report
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 1 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
OUTPUT CHARACTERISTICS
Parameter
Remote Sense (Main Output)
Output Rise (Monotonic)
Conditions
Min.
Typ.
Max.
120
Units
mV
Overall compensation at full load; +VE & -VE connections
10% to 95% rise time
No positive voltage excursion above set point
DC Ramp Up
PS_ON activation
3
s
ms
Startup Time
200
12V, 10%-60% and 50-100% or 60%-10% and 100-50% step
3.3/5VSB 50-100% or 100-50% step load 1A/μs slew rate
600
165/ 250
Transient Response
mV
Current Sharing Accuracy (between sharing
modules; up to 8 in parallel)
Hot Swap Transients
At 100% load
10
5
%
%
ms
Hold Up Time2
FL (Full Load); 48VDC nominal input prior to hold up
1
2Assumes deployment within systems utilizing dual redundant “A”and “B” DC input feeds
ENVIRONMENTAL CHARACTERISTICS
Parameter
Storage Temperature Range
Conditions
Non-Condensing
Min.
-40
Typ.
Max.
70
Units
°C
Operating Temperature Range
1500W Output Power; See Derating Curves
Non-Condensing
-5
45
Operating Humidity
Storage Humidity
Altitude (no derating at 40°C)
Shock
5
5
90
95
%
3000
m
G
Non-Operating
30
Sinusoidal Vibration
MTBF (Target)
Non-operating, 0.5G; 5-500Hz
Telcordia SR-332 M1C1 @ 40°C
CAN/CSA C22.2 No 60950-1-07, Am.1:2011, Am 2:2014
ANSI/UL 60950-1-2014
K Hours
lbs/kg
452
Safety Approvals (Standards) –Pending
IEC60950-1:2005 (2nd Ed.), Am 1:2009 + Am 2:2013
Submission
Input Fusing
Weight
Internal 60A/170VDC fast blow fuse on the DC line input
2.314/1.05
PROTECTION CHARACTERISTICS
Output Voltage
Parameter
Conditions
Air inlet temperature; Auto re-start
Min.
60
13
Typ
Max.
70
14
Units
°C
V
N/A
Over-Temperature
Over-Voltage
Latching; toggle PS_ON or recycle DC input to reset
For slow overload events a constant current will be sustained for
1sec followed by a latch off that will auto reset in 5secs.
For hard (short circuit) events the output will shut down within
50ms and auto restart within 200ms.This cycle will be repeated
ten times at which point the output will permanently latch off.The
power module will require to be reset by recycling the incoming
DC source or by “toggling” PS_ON.
12V (Main)
Over-Current
140
160
A
Over-Voltage
Over-Current
Over-Voltage
Over-Current
Over-Voltage
Over-Current
Latching; toggle PS_ON or recycle DC input to reset
Shutdown followed by auto-recovery
Latching; toggle PS_ON or recycle DC input to reset
Shutdown followed by auto-recovery
Latching; toggle PS_ON or recycle DC input to reset
Shutdown followed by auto-recovery
3.4
4.5
5.4
4.5
13.0
2.75
4.0
6
6.0
6
14.5
3.75
V
A
V
A
V
A
3.3VSB
5VSB
12VSB
ISOLATION CHARACTERISTICS
Parameter
Insulation Safety Rating/Test Voltage
Isolation
Conditions
Input to Outputs
Output to Chassis (Ground)
Min.
Typ.
1500
500
Max.
Units
Vdc
Vdc
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 2 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
EMISSIONS AND IMMUNITY
Characteristic
Standard
Compliance
FCC 47 CFR Part 15
CSIPR 22/EN55022
IEC/EN 61000-4-2;
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
NEBS GR-1089-CORE Issue
Conducted Emissions
Class A with 6dB margin
ESD Immunity
Level 4; Criteria A
Level 2; Criteria B
Level 2; Criteria A
Level 2; Criteria A
Level 2; Criteria A
3A/m; Criteria B
Relevant sections and compliance levels TBD
Radiated Field Immunity
Electrical Fast Transients/Burst Immunity
Surge Immunity
RF Conducted Immunity
Magnetic Field Immunity
Voltage Dips & Interruptions
STATUS INDICATORS
Conditions
GREEN (Power) LED Status
LED not illuminated
Blinking
AMBER (Fault) LED Status
LED not illuminated
LED not illuminated
LED not illuminated
Solid Amber
No incoming DC supply present; power module i s completely off.
Standby Rail ON; Main Output OFF; DC input present & correct
Standby Rail ON; Main Output ON
Main Output overcurrent; undervoltage, overvoltage warning
FAN_FAULT; overtemperature; standby rail overcurrent, Main Output overcurrent or overvoltage
Power Module Warning Event
Solid Green
LED not illuminated
LED not illuminated
LED not illuminated
Solid Amber
Blinking
ADDR ADDRESS SELECTION
ADDR pin (A3) resistor to GND
Power Supply Main Controller
Power Supply External EEPROM
(K-ohm)*
(Serial Communications Slave Address)
(Serial Communications Slave Address)
0.82
2.7
5.6
8.2
15
27
56
180
0xB0
0xB2
0xB4
0xB6
0xB8
0xBA
0xBC
0xBE
0xA0
0xA2
0xA4
0xA6
0xA8
0xAA
0xAC
0xAE
* The resistor shall be +/-5% tolerance
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 3 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
STATUS AND CONTROL SIGNALS
Signal Name
I/O
Description
Interface Details
The signal output is driven high when the input source is available and within acceptable limits.
The output is driven low to indicate loss of input power.
Pulled up internally via 10K to VDD1.
A logic high >2.0Vdc
INPUT_OK (DC Source)
Output There is a minimum of 0.5ms pre-warning time before the signal is driven low prior to the PWR_OK
signal going low. The power supply must ensure that this interface signal provides accurate status
when input source is lost.
A logic low <0.8Vdc
Driven low by internal CMOS buffer
(open drain output).
Pulled up internally via 10K to VDD1.
The signal is asserted (driven high) by the power supply to indicate that all outputs are valid. If any of A logic high >2.0Vdc
PW_OK (Output OK)
Output the outputs fail then this output will be hi-Z or driven low. The output is driven low to indicate that
the Main output is outside of lower limit of regulation (11.4Vdc).
A logic low <0.8Vdc
Driven low by internal CMOS buffer
(open drain output).
The signal output is driven low to indicate that the power supply has detected a warning or fault and Pulled up internally via 10K to VDD1.
is intended to alert the system. This output must be driven high when the power is operating
Output correctly (within specified limits).
A logic high >2.0Vdc
A logic low <0.8Vdc
Driven low by internal CMOS buffer
(open drain output).
SMB_ALERT
(FAULT/WARNING)
The signal will revert to a high level when the warning/fault stimulus (that caused the alert) is
removed.
PRESENT_L
(Power Supply Absent)
The signal is used to detect the presence (installed) of a module by the host system. The signal is
Passive connection to +VSB_Return.
A logic low <0.8Vdc
Output
connected to PSU logic SGND within the power module.
This signal is pulled up internally to the internal housekeeping supply (within the power supply). The Pulled up internally via 10K to VDD1.
PS_ON
(Power Supply
Enable/Disable
power supply main 12Vdc output will be enabled when this signal is pulled low to +VSB_Return.
In the low state the signal input shall not source more than 1mA of current. The 12Vdc output will be A logic low <0.8Vdc
disabled when the input is driven higher than 2.4V, or open circuited. Cycling (toggling) this signal
shall clear latched fault conditions.
A logic high >2.0Vdc
Input
Input is via CMOS Schmitt trigger
buffer.
Pulled up internally via 10K to VDD1.
This signal is used during hot swap to disable the main output during hot swap extraction. The input A logic high >2.0Vdc
PS_KILL
Input
Input
Both
Both
is pulled up internally to the internal housekeeping supply (within the power supply).
The signal is provided on a short (lagging pin) and should be connected to +VSB_Return.
A logic low <0.8Vdc
Input is via CMOS Schmitt trigger
buffer.
An analog input that is used to set the address of the internal slave devices (EEPROM and
microprocessor) used for digital communications.
DC voltage between the limits of 0 and
+3.3Vdc.
ADDR (Address Select)
SCL (Serial Clock)
SDA (Serial Data)
Connection of a suitable resistor to +VSB_Return, in conjunction with an internal resistor divider
chain, will configure the required address.
A serial clock line compatible with PMBusTM Power Systems Management Protocol Part 1 – General
Requirements Rev 1.1.
VIL is 0.8V maximum
VOL is 0.4V maximum when sinking
3mA
No additional internal capacitance is added that would affect the speed of the bus.
The signal is provided with a series isolator device to disconnect the internal power supply bus in the VIH is 2.1V minimum
event that the power module is unpowered.
A serial data line compatible with PMBusTM Power Systems Management Protocol Part 1 – General
Requirements Rev 1.1.
VIL is 0.8V maximum
VOL is 0.4V maximum when sinking
The signal is provided with a series isolator device to disconnect the internal power supply bus in the 3mA
event that the power module is unpowered,
VIH is 2.1V minimum
Remote sense connections intended to be connected at and sense the voltage at the point of load.
The voltage sense will interact with the internal module regulation loop to compensate for voltage
drops due to connection resistance between the output connector and the load.
If remote sense compensation is not required then the voltage can be configured for local sense by:
1. V1_SENSE directly connected to power blades 6 to 10 (inclusive)
Compensation for up to 0.12Vdc total
connection drop (output and return
connections).
V1_SENSE
V1SENSE_RTN
Input
2. V1_SENSE_RTN directly connected to power blades 1 to 5 (inclusive)
The current sharing signal is connected between sharing units (forming an ISHARE bus). It is an input
and/or an output (bi-directional bus) as the voltage on the line controls the current share between
sharing units. A power supply will respond to a change in this voltage; however a power supply can
Bi-
Analogue voltage:
ISHARE
Directional also change the voltage depending on the load drawn from it. On a single unit the voltage on the pin +8V maximum; 10K to +12V_RTN
Bus
(and the common ISHARE bus would read 8VDC at 100% load (module capability). For two identical
units sharing the same 100% load this would read 4VDC for perfect current sharing (i.e. 50% module
load capability per unit).
1.
VDD is an internal voltage rail derived from VSB and an internal housekeeping rail (“diode ORed”); this rail is compatible with the voltage levels of TTL and CMOS logic families.
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 4 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
TIMING SPECIFICATIONS
Turn-On Delay & Output Rise Time:
1. The turn-on delay after application of DC input within the operating range shall as defined in the following tables.
2. The output rise times shall be measured from 10% of the nominal output to the lower limit of the regulation band as defined in the following tables.
Time
Min
Max
Vsb Rise time
V1 Rise time
Vsb Power-on-delay
V1 Power-on-delay
V1 PS_ON delay
20ms
150ms
220ms
1200ms
1500ms
300ms
450ms
1500ms
120ms
400ms
500ms
100ms
300ms
500ms
V1 PWOK delay
DC_OK (Input) detect
TIMING SPECIFICATIONS
Turn-Off (Shutdown by PS_ON)
Turn-Off Timing
V1 Fall time
V1 PS_OFF delay
PW_OK delay off
Min
-
0ms
1.0ms
Max
-
6ms
Notes
Must be monotonic
Vsb
V1
V1 PS_OFF delay
V1 Falltime
PS_ON
Input_OK
PW_OK delayoff
PWOK
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 5 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
TIMING SPECIFICATIONS
Power Removal Holdup
Power Removal Timing
Vsb holdup
V1 holdup (Total Effective)
DC (Input) fail detect
PWOK delay off
Min
3ms
1ms
400µs
-
Max
25ms
-
1000µs
0.8ms
2.2ms
Notes
+VSB Full Load
100% load
100% load
PWOK Hold Up
-
DERATING CURVES
D1U54-D-1500-12-HxxPC Derating With Temperature
140
120
100
80
60
40
20
0
-5
5
15
25
35
45
55
Operating Temperature (°C)
NOTE: The D1U54-D-1500-12-HxxPC power supply has an integral fan; the fan speed is adjusted to achieve the required cooling airflow based on prevailing operating temperature/conditions and output
loading.
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 6 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
OUTPUT CONNECTOR AND SIGNAL INTERFACE; FCI 10122460-005LF or Equivalent
1) With respect to signals columns 5, “3” refers to the shortest level signal pin; the “shortest” pins are the “last to make, first to break” in the mating sequence.
2) Actual connector may not appear exactly as shown above. Refer to the manufacturer’s datasheet for details
PIN ASSIGNMENTS: D1U54-D-1500-12-HxxC
or Equivalent (Power Supply)
FCI 10122460-005LF
Pin
Function
Description
6, 7, 8, 9, 10
V1 (+12VOUT) +12V Main Output
1, 2, 3, 4, 5
A1
+12V RTN/PGND +12V Main Output Return
+VSB
+VSB
Standby Output
Standby Output
B1
C1
+VSB
Standby Output
D1
E1
+VSB
+VSB
Standby Output
Standby Output
A2
B2
C2
D2
E2
A3
B3
C3
+VSB_Return
+VSB_Return
Unused
Unused
Unused
ADDR
Unused
SDA
Standby Output Return
Standby Output Return
No End User Connection
No End User Connection
No End User Connection
I2C Address Protocol Selection (Select by appropriate pull down resistor
No End User Connection
I2C Serial Data Line
D3
E3
A4
V1_SENSE_R
V1_SENSE
SCL
Remote Sense Return (-VE)
Remote Sense (+VE)
I2C Serial Clock Line
B4
C4
D4
E4
A5
PS_ON_L
SMB_ALERT
Unused
DC_OK
PS_KILL
ISHARE
Remote On/Off (Enable/Disable)
Alert signal to host system
No End User Connection
DC Input Source Present & “OK”
Power Supply “kill”; short pin
Current Share bus; short pin
Power “OK”; short pin
B5
C5
PW_OK
D5
E5
Unused
PRESENT_L
No End User Connection
Power Module Present; short pin
POWER SUPPLY INPUT TERMINAL BLOCK
Supplier
P/N
Dinkle Enterprise (Input Terminal Block)
DT-7C-B14W-02
MATING CONNECTORS
Supplier
TE Connectivity (Tyco)
FCI Connect
Solder Right Angle
2-1926739-5
10108888-R10253SLF
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 7 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
WIRING DIAGRAM
Dotted lines show optional remote sense connections.
Optional remote sense lines can be attached to a load that is a distance
away from the power supply to improve regulation at the load.
V1_SENSE
(Main Output Remote Sense)
V1_SENSE
(Main Output Remote Sense)
E3
E3
D1U54x
D1U54x
+12V Main Output
+12V Main Output
6-10
6 -10
+12V
Load
1 - 5
1 - 5
+12V Main Output Return
V1_SENSE_R
ISHARE
+12V Main Output Return
V1_SENSE_R
D3
B5
D3
B5
ISHARE
VSB
VSB
A1, B1, C1,
D1, E1
A1, B1, C1,
D1, E1
PS_ON
PS_ON
VSB
Load
B4
B4
FET, BJT, wire or
switch (debounced)
to turn on +12V
Main Output
A2, B2
A5
VSB_Return
PS_KILL
A2, B2
A5
VSB_Return
PS_KILL
1. Main 12VDC Output: Active share bus.The ISHARE bus (Pin B5 or D4) must be connected on all sharing modules. It is not required that the SENSE signals are
connected to the remote load for current share to operate correctly.
2. Up to eight (8) power modules can be connected in parallel (non-redundant) or N+1 configuration. The current share bus is bi-directional (can source or sink
current from the ISHARE bus).
The voltage of the bus would measure 8VDC for a single power module at 100% load; for two (2) modules sharing a common load the ISHARE bus voltage would
be 4V for a perfect 50/50 current share scenario.
3. The VSB (Standby Output) output of the power module can also be connected in parallel; internal output isolation devices are provided however the
combined available power is limited to that available from a single power module (3.3V @ 13.2W or 5V @ 20W; 12V @ 30W) irrespective of the number of modules
connected in parallel.
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 8 of 9
D1U54-D-1500-12-HxxC Series
54mm 1U Front End DC-DC Power Converter
MECHANICAL DIMENSIONS
1. Input Terminal Block is a Dinkle Enterprise DT-7C-B14W-02
2. Dimensions: 1.57" x 12.66" x 2.15" (40.0 x 321.5mm x 54.5mm)
3.
Safety earth/ground connection via separate dedicated M4 pan head screw connection (located above terminal block)
4. This drawing is a graphical representation of the product and may not show all fine details.
5. Reference File: D1U54-D-1500-12-HxxC -1897_Drawing for Product Datasheet _20160411.pdf
OPTIONAL ACCESSORIES
Description
Part Number
D1U54P-12-CONC Output Interface Connector Card
D1U54P-12-CONC
APPLICATION NOTES
Document Number
Description
Link
http://power.murata.com/datasheet?/data/apnotes/acan-64.pdf
ACAN-64
D1U54P-12-CONC Output Interface Connector Card
D1U54-D-12 Communications Protocol
ACAN-67
http://power.murata.com/datasheet?/data/apnotes/acan-67.pdf
This product is subject to the following operating requirements and the Life and
Safety Critical Application Sales Policy:
Murata Power Solutions, Inc.
Refer to: http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained
herein, will not infringe upon existing or future patent rights.The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
constructed in accordance therewith. Specifications are subject to change without notice.
© 2016 Murata Power Solutions, Inc.
www.murata-ps.com/suppor
t
D1U54-D-1500-12-HxxC.A02 Page 9 of 9
相关型号：
©2020 ICPDF网 联系我们和版权申明