GCG1550C1H6R5CA01#
更新时间：2024-10-30 05:41:50
品牌：MURATA
描述：汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]
概述
数据手册GCG1550C1H6R5CA01# 概述
汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]
GCG1550C1H6R5CA01# 数据手册
通过下载GCG1550C1H6R5CA01#数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Chip Monolithic Ceramic Capacitor for Automotive limited to Conductive Glue Mounting
GCG1550C1H6R5CA01_ (0402, CHA:, 6.5pF, DC50V)
_: packaging code
Reference Sheet
1.Scope
This product specification is applied to Chip Monolithic Ceramic Capacitor limited to Conductive Glue Mounting Type used for Automotive Electronic equipment with
conductive glue mounting.
ꢀꢀ
2.MURATA Part NO. System
(Ex.)
GCG
15
5
0C
1H
6R5
C
A01
D
(2)T
Dimensions
(1)L/W
Dimensions
(4)Rated
Voltage
(3)Temperature
Characteristics
(6)Capacitance
Tolerance
(7)Murata’s Control
(5)Nominal
Capacitance
(8)Packaging Code
Code
3. Type & Dimensions
(Unit:mm)
(1)-1 L
1.0±0.1
(1)-2 W
0.5±0.05
(2) T
0.5±0.05
e
g
0.15 to 0.35
0.3 min.
4.Rated value
Specifications and Test
Methods
(4)
Rated
Voltage
(6)
(3) Temperature Characteristics
Temp. coeff
orꢀCap. Change
(5) Nominal
Capacitance
Capacitance
Tolerance
(Operating
Temp. Range)
Temp. Range
(Ref.Temp.)
20 to 150 °C
(20 °C)
DC 50 V
6.5 pF
±0.25 pF
0±60 ppm/°C
-55 to 150 °C
5.Package
mark
(8) Packaging
Packaging Unit
f180mm Reel
PAPER W8P2
f180mm Reel
PAPER W8P1
f330mm Reel
PAPER W8P2
D
10000 pcs./Reel
20000 pcs./Reel
50000 pcs./Reel
W
J
Product specifications in this catalog are as of Apr.16,2016,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
GCG1550C1H6R5CA01-01
1
■AEC-Q200 Murata Standard Specification and Test Methods
Specification.
No
AEC-Q200 Test Item
AEC-Q200 Test Method
High Dielectric Type
Temperature
Compensating Type
Pre-and Post-Stress
Electrical Test
1
2
-
High Temperature
Exposure (Storage)
The measured and observed characteristics should satisfy the
specifications in the following table.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16.
Appearance No marking defects
Capacitance Within ±2.5% or ±0.25pF
Set the capacitor for 1000±12 hours at 150±3℃. Set for
24±2 hours at room temperature, then measure.
R7/L8/R9:Within ±12.5%
Change
Q/D.F.
(Whichever is larger)
30pFmin. : Q≧1000
R7/L8 : 0.05 max.
R9 : 0.075max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
I.R.
More than 10,000MΩ or 500Ω・ F
R9 : More than 3,000MΩ or 150 Ω・ F
(Whichever is smaller)
3
Temperature Cycling
The measured and observed characteristics should satisfy the
specifications in the following table.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16. Perform the 1000 cycles
according to the four heat treatments listed in the following table.
Set for 24±2 hours at room temperature, then measure
Appearance No marking defects
Capacitance Within ±2.5% or ±0.25pF
R7/L8/R9: Within ±10.0%
Change
Q/D.F.
(Whichever is larger)
Step
1
2
3
4
30pFmin.: Q ≧1000
R7/L8 W.V.: 25Vmin.: 0.03 max.
ꢀꢀꢀꢀꢀW.V.: 16V : 0.05 max
R9 : 0.075max.
125+3/-0
Temp.
Room
(for1C/2C/3C/4C/5C/R7)
150+3/-0
Room
30pFmax.: Q ≧ 400+20C
C: Nominal Capacitance (pF)
-55+0/-3
(℃)
Temp.
Temp.
(for 0C/5G/L8/R9)
I.R.
Time
More than 10,000MΩ or 500Ω ・F
15±3
1
15±3
1
(min.)
(Whichever is smaller)
・ Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10 ℃ for one hour and then set
for 24±2 hours at room temperature.
Perform the initial measurement.
4
5
Destructive
No defects or abnormalities
Per EIA-469.
Physical Analysis
Moisture Resistance
The measured and observed characteristics should satisfy the
specifications in the following table.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16.
Apply the 24-hour heat (25 to 65℃) and humidity (80 to 98%)
treatment shown below, 10 consecutive times.
Set for 24±2 hours at room temperature, then measure.
Appearance No marking defects
Capacitance Within ±3.0% or ±0.30pF
Humidity
80～98%
Humidity
80～98%
R7/L8/R9: Within ±12.5%
R7/L8 : 0.05 max.
R9 : 0.075max.
Temperature
Humidity
90～98%
Humidity
90～98%
Humidity
90～98%
(℃)
Change
Q/D.F.
(Whichever is larger)
70
65
60
55
50
45
40
35
30
25
20
15
10
5
30pFmin. : Q≧350
10pF and over, 30pF and below:
Q≧275+5C/2
10pFmax.: Q ≧200+10C
C: Nominal Capacitance(pF)
I.R.
More than 10,000MΩ or 500Ω ・F
+10
- 2 ℃
R9 : More than 3,000MΩ or 150 Ω・ F
Initial measuremt
0
-5
(Whichever is smaller)
-10
One cycle 24hours
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Hours
6
The measured and observed characteristics should satisfy the
specifications in the following table.
Biased Humidity
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16.
Apply the rated voltage and 1.3+0.2/-0vdc (add 6.8kΩ resister)
Appearance No marking defects
at 85±3℃ and 80 to 85% humidity for 1000±12 hours.
Remove and set for 24±2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
Capacitance Within ±3.0% or ±0.30pF
R7/L8/R9: Within ±12.5%
Change
(Whichever is larger)
Q/D.F.
I.R.
30pF and over: Q≧200
R7/L8 : 0.05 max.
R9 : 0.075max.
30pF and below: Q≧100+10C/3
C: Nominal Capacitance(pF)
More than 1,000MΩ or 50Ω ・F
(Whichever is smaller)
JEMCGS-03866
2
■AEC-Q200 Murata Standard Specification and Test Methods
Specification.
High Dielectric Type
No
7
AEC-Q200 Test Item
Operational Life
AEC-Q200 Test Method
Temperature
Compensating Type
The measured and observed characteristics should satisfy the
specifications in the following table.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16.
Appearance
Capacitance
Change
No marking defects
Apply 200% of the rated voltage for 1000±12 hours
at 125±3℃(for 1C/2C/3C/4C/5C//R7), 150±3℃(for 0C/5G/L8/R9).
Set for 24±2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
Within ±3.0% or ±0.30pF
(Whichever is larger)
30pFmin. : Q≧350
R7/L8/R9: Within ±12.5%
R7/L8 : 0.05 max.
Q/D.F.
10pF and over, 30pF and below: R9 : 0.075max.
Q≧275+5C/2
・ Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the maximum
operating temperature ±3℃. Remove and set for 24±2 hours at
room temperature. Perform initial measurement.
10pFmax.: Q ≧200+10C
C: Nominal Capacitance(pF)
More than 1,000MΩ or 50Ω ・F
(Whichever is smaller)
I.R.
8
9
External Visual
No defects or abnormalities
Visual inspection
Using calipers
Physical Dimension
Within the specified dimensions
10 Resistance to Appearance
No marking defects
Per MIL-STD-202 Method 215
Solvents
Capacitance
Within the specified tolerance
Solvent 1 : 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
Change
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V : 0.035 max.
R9 : 0.075max.
Solvent 2 : Terpene defluxer
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
Solvent 3 : 42 parts (by volume) of water
1part (by volume) of propylene glycol monomethyl ether
1 part (by volume) of monoethanolamine
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
11 Mechanical
Shock
Appearance
Capacitance
Change
No marking defects
Fix the capacitor to the test jig in the same manner and under the
same conditions as No.16.Three shocks in each direction should be
applied along 3 mutually perpendicular axes of the test specimen
(18 shocks).
Within the specified tolerance
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V : 0.035 max.
R9 : 0.075max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
The specified test pulse should be Half-sine and should have a
duration :0.5ms, peak value:1500g and velocity change: 4.7m/s.
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
12 Vibration
Appearance
Capacitance
Change
No defects or abnormalities
Within the specified tolerance
Fix the capacitor to the test jig in the same manner and under the
same conditions as No.16. The capacitor should be subjected to a
simple harmonic motion having a total amplitude of 1.5mm, the
frequency being varied uniformly between the approximate limits of
10 and 2000Hz. The frequency range, from 10 to 2000Hz and
return to 10Hz, should be traversed in approximately 20 minutes.
This motion should be applied for 12 cycle in each 3 mutually
perpendicular directions
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V : 0.035 max.
R9 : 0.075max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
13 Thermal Shock
The measured and observed characteristics should satisfy the
specifications in the following table.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as No.16. Perform the 300 cycles
according to the two heat treatments listed in the following
table(Maximum transfer time is 20 seconds). Set for 24±2 hours at
room temperature, then measure
Appearance
Capacitance
Change
No marking defects
Within ±2.5% or ±0.25pF
(Whichever is larger)
R7/L8/R9: Within ±10.0%
Step
1
2
125+3/-0
(for1C/2C/3C/4C/5C/R7)
150+3/-0
(for 0C/5G/L8/R9）
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
GCG21BL81H104K: 0.03 max.
W.V.: 16V : 0.035 max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
Temp.(℃）
-55+0/-3
Time
(min.）
R9 : 0.075max
15±3
15±3
I.R.
More than 10,000MΩ or 500Ω・F
(Whichever is smaller)
・ Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10 ℃ꢀfor one hour and then set
for 24±2 hours at room temperature.
Perform the initial measurement.
JEMCGS-03866
3
■AEC-Q200 Murata Standard Specification and Test Methods
Specification.
No
AEC-Q200 Test Item
AEC-Q200 Test Method
High Dielectric Type
Temperature
Compensating Type
14 ESD
Appearance
Capacitance
Change
No marking defects
Per AEC-Q200-002
Within the specified tolerance
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V :0.035 max.
R9 : 0.075max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
I.R.
More than 10,000MΩ or 500Ω・F
(Whichever is smaller)
15 Electrical Appearance
Chatacteri- Capacitance
No defects or abnormalities
Within the specified tolerance
Visual inspection.
The capacitance/Q/D.F. should be measured at 20℃(for 0C/1C/2C/3C/4C),
25℃(for 5C/5G/R7/L8/R9) at the frequency and voltage shown in the table.
zation
Change
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V : 0.035 max.
R9 : 0.075max.
Char.
ΔC,5G
(more than 1000pF)
R7,R9,L8(C≦10μF)
ΔC,5G
(1000 pF and below)
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
Item
Frequency
Voltage
1±0.1MHz
1±0.1kHz
0.5 to 5Vrms
1±0.2Vrms
The insulation resistance should be measured with a DC voltage not
exceeding the rated voltage at 25℃ and 125℃(for 1C/2C/3C/4C/5C/R7)/
150℃(for 0C/5G/L8/R9）within 2 minutes of charging.
I.R.ꢀ25℃
More than 100,000MΩ or 1000Ω・F More than 10,000MΩ or 500Ω・F
(Whichever is smaller)
(Whichever is smaller)
I.R.ꢀ125℃
I.R.ꢀ150℃
More than 10,000MΩ or 100Ω・F
More than 1,000MΩ or 10Ω・F
(Whichever is smaller)
(Whichever is smaller)
More than 10,000MΩ or 100Ω・F
More than 1,000MΩ or 1Ω・F
(Whichever is smaller)
(Whichever is smaller)
No failure should be observed when 250% of the rated voltage is
applied between the terminations for 1 to 5 seconds, provided the
charge/ discharge current is less than 50mA.
Dielectric
Strength
No failure
16 Terminal
Strength
Appearance
No marking defects
Mount the capacitor on the test jig in Fig.1 using a conductive glue
(HEREAUS"PC3000").
Capacitance
Change
Within specified tolerance
The conductive glue is hardened at 140℃ for 30minites.
Then apply *shear tension in parallel with the test jig for 60sec.
Q/D.F.
30pFmin. : Q≧1000
R7/L8 : W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035max.
R9 : 0.075max.
30pFmax.: Q ≧400+20C
C: Nominal Capacitance(pF)
*Show in the table 1
Alumina
Ag Pd electrode
c
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
b
a
Type
GCG15
GCG18
GCG21
GCG31
GCG32
Share Tension
2.0N
2.7N
4.9N
6.9N
12.6N
Type
GCG15
GCG18
GCG21
GCG31
GCG32
a
b
c
0.4
1.0
1.2
2.2
2.2
1.5
3.0
4.0
5.0
5.0
0.5
1.2
1.65
Table.1
2.0
2.9
Fig.1
（in mm）
JEMCGS-03866
4
■AEC-Q200 Murata Standard Specification and Test Methods
Specification.
No
AEC-Q200 Test Item
AEC-Q200 Test Method
High Dielectric Type
Temperature
Compensating Type
17 Beam Load Test
Destruction value should be exceed following one.
< Chip L dimension : 2.5mm max. >
Place the capacitor in the beam load fixture as Fig 2.
Apply a force.
< Chip Length : 2.5mm max. >
Chip thickness > 0.5mm rank : 20N
Chip thickness ≦0.5mm rank : 8N
< Chip L dimension : 3.2mm mim. >
Iron Board
Chip thickness < 1.25mm rank : 15N
Chip thickness ≧1.25mm rank : 54.5N
< Chip Length : 3.2mm min. >
L
0.6L
Fig.2
Speed supplied the Stress Load : 0.5mm / sec.
18 Capacitance
Temperature
Capacitance
Change
Within the specified tolerance.
(Table A)
R7 : Within ±15%
(-55℃ to +125℃)
L8 : Within ±15%
(-55℃ to +125℃)
ꢀꢀꢀWithin +15/-40%
(+125℃ to +150℃)
R9 : Within ±15%
(-55℃ to +150℃)
The capacitance change should be measured after 5 min. at
each specified temperature stage.
Characteristics
(1)Temperature Compensating Type
The temperature coefficient is determined using the capacitance
measured in step 3 as a reference. When cycling the temperature
sequentially from step1 through 5 (Δ C: +25℃ to +125℃,
5G:+25℃ to +150℃ other temp. coifficient.:+25℃ to +85℃) the
capacitance should be within the specified tolerance for the
temperature coefficient and capacitance change as Table A-1. The
capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in the step
1,3 and 5 by the cap value in step 3.
Temperature
Coefficient
Within the specified tolerance.
(Table A)
Step
1
Temp.(℃)
25±2
2
3
-55±3
25±2
125±3(for 1C/2C/3C/4C/5C/R7)
150±3(for 0C/5G/L8/R9)
4
5
Within ±0.2% or ±0.05 pF
Capacitance
Drift
25±2
(Whichever is larger.)
(2) High Dielectric Constant Type
The ranges of capacitance change compared with the above 25℃
value over the temperature ranges shown in the table should be
within the specified ranges.
Initial measurement for high dielectric constant type.
Perform a heat treatment at 150+0/-10℃ for one hour
and then set for 24±2 hours at room temperature.
Perform the initial measurement.
Table A
Capacitance Change from 20℃ (%)
Nominal Values
(ppm/℃)*1
Char.
-55
-25
-10
Max.
0.54
0.82
1.37
2.56
Min.
-0.23
-0.45
-0.90
-1.88
Max.
0.33
0.49
0.82
1.54
Min.
-0.14
-0.27
-0.54
-1.13
Max.
0.22
0.33
0.55
1.02
Min.
-0.09
-0.18
-0.36
-0.75
1C
0C/2C
3C
0±30
0±60
0±120
0±250
4C
*1 Nominal values denote the temperature coefficient with a range of 20℃ to 125℃.
(0C: temperature coefficient with a range of 20℃ to 150℃.)
Capacitance Change from 25C (%)
-30
Nominal Values
(ppm/C) *2
Char.
-55
-10
Max.
0.58
Min.
-0.24
Max.
0.40
Min.
-0.17
Max.
0.25
Min.
-0.11
5C/5G
0± 30
*2:Nominalvaluesdenotethetemperaturecoefficient withinarangeof25Cto125C(forC)/150C(for5G).
JEMCGS-03866
5
Package
GCG Type
1.Tape Carrier Packaging(Packaging Code:D/E/W/F/L/J/K)
1.1 Minimum Quantity(pcs./reel)
φ180mm reel
Paper Tape
φ330mm reel
Plastic Tape Paper Tape Plastic Tape
Type
Code:D/E
Code:W
20000
(W8P1)
Code:L
Code:J/ F
50000
(W8P2)
10000
Code:K
10000
(W8P2)
4000
GCG15 5
GCG18 8
6
4000
10000
GCG21
9
4000
10000
B
M
C
D
E
3000
3000
2000
1000
1000
10000
10000
6000
4000
4000
GCG31
GCG32
1.2 Dimensions of Tape
(in:mm)
(1)GCG15(W8P2 CODE:D/E/J/F)ꢀ<Paper Tape>
*1,2：2.0±0.05
4.0±0.1
+0.1
-0
*1
*2
φ1.5
Ａ
0.05 max.
Dimensions
t
Type
Tolerance(Chip)
A *3
0.65
B *3
1.15
ｔ
L
W
GCG15
5
±0.1
±0.05
0.8 max.
*3 Nominal value
(in:mm)
(2)GCG15(W8P1 CODE:W)ꢀ<Paper Tape>
4.0±0.1
1.0±0.05
+0.1
-0
φ1.5
Ａ
1.0±0.05
t
Dimensions
Type
A *3
0.65
B *3
1.15
ｔ
L
W
GCG15
5
±0.1
±0.05
0.8 max.
*3 Nominal value
JEMCGP-04125
6
Package
GCG Type
ꢀ(3)GCG18/21ꢀ<Paper Tape>
(in:mm)
4.0±0.1
4.0±0.1
2.0±0.1
+0.1
-0
φ1.5
Ａ
t
Dimensions
Tolerance(Chip)
TDimensions
(Chip)
Type
A
B
t
L
W
GCG18
±0.2
±0.1
0.8±0.1
0.6±0.1
0.85±0.1
1.05±0.10
1.55±0.15
1.85±0.10
2.30±0.15
8
6
9
1.1max.
GCG21
±0.3
±0.2
ꢀ(4)GCG21/31/32 <Plastic Tape>
4.0±0.1
4.0±0.1
2.0±0.1
0.25±0.1(T≦1.8mm)
0.3±0.1(T：2.5mm)
+0.1
φ1.5
-0
Ａ
t
Dimensions
Tolerance(Chip)
T Dimensions
(Chip)
Type
A
B
t
L
W
GCG21
GCG31
±0.3
±0.2
1.25±0.2
1.15±0.2
1.6±0.3
2.0±0.3
2.5±0.3
1.45±0.20 2.25±0.20
1.90±0.20 3.50±0.20
2.0 max.
1.7 max.
2.5 max.
3.0 max.
3.7 max.
B
M
C
D
E
±0.3
±0.4
±0.3
±0.3
GCG32
2.80±0.20 3.50±0.20
JEMCGP-04125
7
Package
GCG Type
Fig.1 Package Chips
(in:mm)
Chip
Fig.2 Dimensions of Reel
2.0±0.5
φ21±0.8
ｗ1
W
W
w1
10±1.5
Fig.3 Taping Diagram
GCG32 max.
16.5 max.
Top Tape : Thickness 0.06
Feeding Hole :As specified in 1.2.
Hole for Chip : As specified in 1.2.
Bottom Tape :Thickness 0.05
(Only a bottom tape existence )
Base Tape : As specified in 1.2.
JEMCGP-04125
8
Package
GCG Type
1.3 Tapes for capacitors are wound clockwise shown in Fig.3.
(The sprocket holes are to the right as the tape is pulled toward the user.)
1.4 Part of the leader and part of the vacant section are attached as follows.
Tail vacant Section
Chip-mounting Unit Leader vacant Section
(in:mm)
Leader Unit
(Top Tape only)
Direction
of Feed
160 min.
190 min.
210 min.
1.5 Accumulate pitch : 10 of sprocket holes pitch = 40±0.3mm
1.6 Chip in the tape is enclosed by top tape and bottom tape as shown in Fig.1.
1.7 The top tape and base tape are not attached at the end of the tape for a minimum of 5 pitches.
1.8 There are no jointing for top tape and bottom tape.
1.9 There are no fuzz in the cavity.
1.10 Break down force of top tape : 5N min.
Break down force of bottom tape : 5N min. (Only a bottom tape existence )
1.11 Reel is made by resin and appeaser and dimension is shown in Fig 2.
There are possibly to change the material and dimension due to some impairment.
1.12 Peeling off force : 0.1N to 0.6N in the direction as shown below.
Top tape
165～180°
1.13 Label that show the customer parts number, our parts number, our company name, inspection
number and quantity, will be put in outside of reel.
JEMCGP-04125
9
! Caution
■Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high reliability
ꢀ for the prevention of defects which might directly cause damage to the third party's life, body or property.
ꢀꢀꢀ①Aircraft equipment ②Aerospace equipment ③Undersea equipment ④Power plant control equipment
ꢀꢀꢀ⑤Medical equipment ⑥Transportation equipment(vehicles,trains,ships,etc.) ⑦Traffic signal equipment
ꢀꢀꢀ⑧Disaster prevention / crime prevention equipment
⑨Data-processing equipment
ꢀꢀꢀ⑩Application of similar complexity and/or reliability requirements to the applications listed in the above.
■Storage and Operation condition
1. If store the chip monolithic ceramic capacitors in an atmosphere consisting of high temperature or humidity,
sulfur or chlorine gases, contaminants attach to the surface of external electrode, and bondability with
conductive glue may deteriorate. Do not store the capacitors in an atmosphere consisting of corrosive gas
(e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammoria gas, etc.). Storage environment must be at room
temperature of +5°C to +40°C and a relative humidity of 20% to 70%, and use the product within six months.
In case of packaging, do not open the last wrappend, polyethylene bag, till just before using.
After unpacking, immediately reseal, or store in a desiccator containing a desiccant.
ꢀ
2. Due to moisture condensation caused by rapid humidity changes, or the photochemical change caused
by direct sunlight on the terminal electrodes and/or the resin/epoxy coatings, the bondability with conductive glue and
electrical performance may deteriorate. Do not store capacitors under direct sunlight or in high huimidity conditions.
3. This product is chip monolithic ceramic capacitor limited to conductive glue mounting. Do not apply mounting method
other than conductive glue. Flow or reflow soldering can result in a lack of adhesive strength on the outer electrode by
poor wettability, which may result in chips breaking loose from the PCB.
■Rating
1.Temperature Dependent Characteristics
1. The electrical characteristics of the capacitor can change with temperature.
1-1. For capacitors having larger temperature dependency, the capacitance may change with temperature
changes. The following actions are recommended in order to ensure suitable capacitance values.
(1) Select a suitable capacitance for the operating temperature range.
(2) The capacitance may change within the rated temperature.
When you use a high dielectric constant type capacitor in a circuit that needs a tight (narrow) capacitance
tolerance (e.g., a time-constant circuit), please carefully consider the temperature characteristics, and
carefully confirm the various characteristics in actual use conditions and the actual system.
[Example of Temperature Caracteristics X7R(R7)]
[Example of Temperature Characteristics X5R(R6)]
Sample: 0.1μF, Rated Voltage 50VDC
Sample: 22μF, Rated Voltage 4VDC
2
1
1
20
15
10
5
0
-
-5
-1
-1
-2
-10
-15
-20
-75
-50
-25
0
25
50
75
100
-75
-50
-25
0
25
50
75
100 125 150
Temperature (ꢀC)
Temperature (ꢀC)
JEMCGC-04887
10
Caution
!
2.Measurement of Capacitance
1. Measure capacitance with the voltage and frequency specified in the product specifications.
1-1. The output voltage of the measuring equipment may decrease occasionally when capacitance is high.
Please confirm whether a prescribed measured voltage is impressed to the capacitor.
1-2. The capacitance values of high dielectric constant type capacitors change depending on the AC voltage applied.
Please consider the AC voltage characteristics when selecting a capacitor to be used in a AC circuit.
3.Applied Voltage
1. Do not apply a voltage to the capacitor that exceeds the rated voltage as called out in the specifications.
1-1. Applied voltage between the terminals of a capacitor shall be less than or equal to the rated voltage.
(1) When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated DC voltage.
When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed the rated DC voltage.
(2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC voltage.
Typical Voltage Applied to the DC capacitor
DC Voltage
DC Voltage+AC
AC Voltage
Pulse Voltage
0
E
E
E
E
0
0
0
(E：Maximum possible applied voltage.)
1-2. Influence of over voltage
Over voltage that is applied to the capacitor may result in an electrical short circuit caused by the breakdown
of the internal dielectric layers .
The time duration until breakdown depends on the applied voltage and the ambient temperature.
4.Type of Applied Voltage and Self-heating Temperature
1.Confirm the operating conditions to make sure that no large current is flowing into the capacitor due to the
continuous application of an AC voltage or pulse voltage.
When a DC rated voltage product is used in an AC voltage circuit or a pulse voltage circuit, the AC current
or pulse current will flow into the capacitor; therefore check the self-heating condition.
Please confirm the surface temperature of the capacitor so that the temperature remains within the upper limits
of the operating temperature, including the rise in temperature due to self-heating. When the capacitor is
used with a high-frequency voltage or pulse voltage, heat may be generated by dielectric loss.
[Example of Temperature Rise (Heat Generation) in Chip
<Applicable to Rated Voltage of less than 100VDC>
Monolithic Ceramic Capacitors in Contrast to Ripple Current]
1-1. The load should be contained to the level
Sample: R(R1) characteristics 10μF, Rated voltage: DC10V
ꢀ
such that when measuring at atmospheric
ꢀ ꢀtemperature of 25°C, the product's self-heating
ꢀꢀ remains below 20°C and the surface
temperature of the capacitor in the actual circuit
remains within the maximum operating
temperature.
Ripple Current
100
10
100kHz
500kHz
1MHz
1
0
1
2
4
5
6
3
Current (Ar.m.s.)
JEMCGC-04887
11
Caution
!
5. DC Voltage and AC Voltage Characteristic
1. The capacitance value of a high dielectric constant type
capacitor changes depending on the DC voltage applied.
Please consider the DC voltage characteristics when a
capacitor is selected for use in a DC circuit.
[Example of DC Voltage Characteristics]
Sample: R(R1) Characteristics 0.1μF, Rated Voltage 50VDC
2
0
-2
-4
-6
-8
1-1. The capacitance of ceramic capacitors may change
sharply depending on the applied voltage. (See figure)
Please confirm the following in order to secure the
capacitance.
(1) Determine whether the capacitance change caused
by the applied voltage is within the allowed range .
(2) In the DC voltage characteristics, the rate of
capacitance change becomes larger as voltage
increases, even if the applied voltage is below
the rated voltage. When a high dielectric constant
type capacitor is used in a circuit that requires a
tight (narrow) capacitance tolerance (e.g., a time
constant circuit), please carefully consider the
voltage characteristics, and confirm the various
characteristics in the actual operating conditions
-10
0
10
20
30
40
50
DC Voltage (V)
[Example of AC Voltage Characteristics]
Sample: X7R(R7) Characteristics 10μF, Rated Voltage 6.3VDC
30
20
10
0
ꢀ
of the system.
-10
-20
2. The capacitance values of high dielectric
constant type capacitors changes depending
on the AC voltage applied.
-30
-40
-50
-60
Please consider the AC voltage characteristics
when selecting a capacitor to be used in a
AC circuit.
0
0.5
1
1.5
2
AC Voltage (Vr.m.s.)
6. Capacitance Aging
[Example of Change Over Time (Aging characteristics) ]
1. The high dielectric constant type capacitors
have an Aging characteristic in which the capacitance
value decreases with the passage of time.
20
10
0
When you use a high dielectric constant type
capacitors in a circuit that needs a tight (narrow)
capacitance tolerance (e.g., a time-constant circuit),
please carefully consider the characteristics
of these capacitors, such as their aging, voltage,
and temperature characteristics. In addition,
check capacitors using your actual appliances
at the intended environment and operating conditions.
-10
C0G(5C)
X7R(R7)
-20
-30
-40
10
100
1000
10000
Time(h)
7.Vibration and Shock
1. Please confirm the kind of vibration and/or shock, its condition, and any generation of resonance.
Please mount the capacitor so as not to generate resonance, and do not allow any impact on the terminals.
2. Mechanical shock due to being dropped may cause damage or
a crack in the dielectric material of the capacitor.
Crack
Do not use a dropped capacitor because the quality and reliability
may be deteriorated.
Floor
3. When printed circuit boards are piled up or handled, the corner
ꢀof another printed circuit board
Mounting printed circuit board
Crack
should not be allowed to hit the capacitor in order to avoid
a crack or other damage to the capacitor.
JEMCGC-04887
12
Caution
!
■Mounting
1. Selection of Conductive Adhesive, Mounting Process, and Bonding Strength
1.The acuired bonding strength may change greatly depending on the conductive adhesive to be used.
ꢀ Be sure to confirming the desired performance can be acquired in the assumed monting process
ꢀ with the conductive adhesive to be used.
2.Maintenance of the Mounting (pick and place) Machine
1. Make sure that the following excessive forces are not applied to the capacitors.
1-1. In mounting the capacitors on the printed circuit board, any bending force against them shall be kept
to a minimum to prevent them from any damage or cracking. Please take into account the following precautions
and recommendations for use in your process.
(1) Adjust the lowest position of the pickup nozzle so as not to bend the printed circuit board.
(2) Adjust the nozzle pressure within a static load of 1N to 3N during mounting.
Suction Nozzle
ꢀ [Incorrect]
Deflection
Board
Board Guide
ꢀ [Correct]
Support Pin
2.Dirt particles and dust accumulated between the suction nozzle and the cylinder inner wall prevent
the nozzle from moving smoothly. This imposes greater force upon the chip during mounting,
causing cracked chips. Also, the locating claw, when worn out, imposes uneven forces on the chip
when positioning, causing cracked chips. The suction nozzle and the locating claw must be maintained,
checked and replaced periodically.
3.Moisture proof
1.To prevent the silver electrode migration, keep parts under low moisture condition with resin coating and the equivalent.
4.Coating
1. A crack may be caused in the capacitor due to the stress of the thermal contraction of the resin during curing process.
The stress is affected by the amount of resin and curing contraction. Select a resin with low curing contraction.
The difference in the thermal expansion coefficient between a coating resin or a molding resin and the capacitor
may cause the destruction and deterioration of the capacitor such as a crack or peeling, and lead to the deterioration
of insulation resistance or dielectric breakdown.
Select a resin for which the thermal expansion coefficient is as close to that of the capacitor as possible.
A silicone resin can be used as an under-coating to buffer against the stress.
2. Select a resin that is less hygroscopic.
Using hygroscopic resins under high humidity conditions may cause the deterioration of the insulation resistance
of a capacitor. An epoxy resin can be used as a less hygroscopic resin.
3．The halogen system substance and organic acid are included in coating material, and a chip corrodes
ꢀꢀby the kind of Coating material. Do not use strong acid type.
JEMCGC-04887
13
Caution
!
■ Others
1. Under Operation of Equipment
1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of an electric shock.
1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit).
Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.
1-3. Confirm the environment in which the equipment will operate is under the specified conditions.
Do not use the equipment under the following environments.
(1) Being spattered with water or oil.
(2) Being exposed to direct sunlight.
(3) Being exposed to ozone, ultraviolet rays, or radiation.
(4) Being exposed to toxic gas (e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.)
(5) Any vibrations or mechanical shocks exceeding the specified limits.
(6) Moisture condensing environments.
1-4. Use damp proof countermeasures if using under any conditions that can cause condensation.
2. Others
2-1. In an Emergency
(1) If the equipment should generate smoke, fire, or smell, immediately turn off or unplug the equipment.
If the equipment is not turned off or unplugged, the hazards may be worsened by supplying continuous power.
(2) In this type of situation, do not allow face and hands to come in contact with the capacitor or burns may be caused
by the capacitor's high temperature.
2-2. Disposal of waste
When capacitors are disposed of, they must be burned or buried by an industrial waste vendor with the appropriate
licenses.
2-3. Circuit Design
(1) Addition of Fail Safe Function
Capacitors that are cracked by dropping or bending of the board may cause deterioration of the
insulation resistance, and result in a short. If the circuit being used may cause an electrical shock,
smoke or fire when a capacitor is shorted, be sure to install fail-safe functions, such as a fuse,
to prevent secondary accidents.
(2) This series are not safety standard certified products.
2-4. Remarks
Failure to follow the cautions may result, worst case, in a short circuit and smoking when the product is used.
The above notices are for standard applications and conditions. Contact us when the products are used in special
mounting conditions.
Select optimum conditions for operation as they determine the reliability of the product after assembly.
The data herein are given in typical values, not guaranteed ratings.
JEMCGC-04887
14
Notice
■ Rating
1.Operating Temperature
1. The operating temperature limit depends on the capacitor.
1-1. Do not apply temperatures exceeding the maximum operating temperature.
It is necessary to select a capacitor with a suitable rated temperature that will cover the operating temperature range.
It is also necessary to consider the temperature distribution in equipment and the seasonal temperature variable
factor.
1-2. Consider the self-heating factor of the capacitor
The surface temperature of the capacitor shall not exceed the maximum operating temperature including self-heating.
2.Atmosphere Surroundings (gaseous and liquid)
1. Restriction on the operating environment of capacitors.
1-1. Capacitors, when used in the above, unsuitable, operating environments may deteriorate due to the corrosion
of the terminations and the penetration of moisture into the capacitor.
1-2. The same phenomenon as the above may occur when the electrodes or terminals of the capacitor are subject
to moisture condensation.
1-3. The deterioration of characteristics and insulation resistance due to the oxidization or corrosion of terminal
ꢀꢀelectrodes may result in breakdown when the capacitor is exposed to corrosive or volatile gases or solvents
for long periods of time.
3.Piezo-electric Phenomenon
1. When using high dielectric constant type capacitors in AC or pulse circuits, the capacitor itself vibrates
at specific frequencies and noise may be generated.
Moreover, when the mechanical vibration or shock is added to capacitor, noise may occur.
JEMCGC-04887
15
Notice
■ Others
1.Transportation
1. The performance of a capacitor may be affected by the conditions during transportation.
1-1. The capacitors shall be protected against excessive temperature, humidity and mechanical force during transportation.
(1) Climatic condition
ꢀ･ low air temperature : -40℃
･ change of temperature air/air : -25℃/+25℃
･ low air pressure : 30 kPa
･ change of air pressure : 6 kPa/min.
(2) Mechanical condition
Transportation shall be done in such a way that the boxes are not deformed and forces are not directly passed
on to the inner packaging.
1-2. Do not apply excessive vibration, shock, or pressure to the capacitor.
(1) When excessive mechanical shock or pressure is applied to a capacitor, chipping or cracking may occur
in the ceramic body of the capacitor.
(2) When the sharp edge of an air driver, tweezers, a chassis, etc. impacts strongly on the surface
of the capacitor, the capacitor may crack and short-circuit.
1-3. Do not use a capacitor to which excessive shock was applied by dropping etc.
A capacitor dropped accidentally during processing may be damaged.
2.Characteristics Evaluation in the Actual System
1. Evaluate the capacitor in the actual system,to confirm that there is no problem with the performance and specification
values in a finished product before using.
2. Since a voltage dependency and temperature dependency exists in the capacitance of high dielectric type ceramic
capacitors, the capacitance may change depending on the operating conditions in the actual system.
Therefore,be sure to evaluate the various characteristics, such as the leakage current and noise absorptivity,
which will affect the capacitance value of the capacitor.
3. In addition,voltages exceeding the predetermined surge may be applied to the capacitor by the inductance in
the actual system. Evaluate the surge resistance in the actual system as required.
JEMCGC-04887
16
NOTE
!
1.Please make sure that your product has been evaluated in view of your specifications with our
product being mounted to your product.
2.Your are requested not to use our product deviating from this product specification.
3.We consider it not appropriate to include any terms and conditions with regard to the business
transaction in the product specifications, drawings or other technical documents. Therefore,
if your technical documents as above include such terms and conditions such as warranty clause,
product liability clause, or intellectual property infringement liability clause, they will be deemed to
be invalid.
JEMCGC-04887
17
GCG1550C1H6R5CA01# 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| GCG1550C1H6R5DA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R6BA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R6CA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R6DA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R7BA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R7CA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R7DA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R8BA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R8CA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
| GCG1550C1H6R8DA01# | MURATA | 汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] | 获取价格 |
|
GCG1550C1H6R5CA01# 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
