GJ831CR71H475MA12#

更新时间:2024-10-30 05:41:41
品牌:MURATA
描述:民用设备,工业设备,移动设备,植入式以外的医疗器械设备 [GHTF A/B/C],汽车[信息娱乐 / 舒适设备]

GJ831CR71H475MA12# 概述

民用设备,工业设备,移动设备,植入式以外的医疗器械设备 [GHTF A/B/C],汽车[信息娱乐 / 舒适设备]

GJ831CR71H475MA12# 数据手册

通过下载GJ831CR71H475MA12#数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
Low Acoustic Noise Chip Multilayer Ceramic Capacitors for General Purpose  
GJ831CR71H475MA12_ (1206, X7R:EIA, 4.7uF, DC50V)  
_: packaging code  
Reference Sheet  
1.Scope  
This product specification is applied to Low Acoustic Noise Chip Multilayer Ceramic Capacitors used for General Electronic equipment.  
ꢀꢀ  
2.MURATA Part NO. System  
(Ex.)  
GJ8  
31  
C
R7  
1H  
475  
M
A12  
L
(2)T  
Dimensions  
(1)L/W  
Dimensions  
(4)Rated  
Voltage  
(3)Temperature  
Characteristics  
(6)Capacitance  
Tolerance  
(7)Murata’s Control  
(5)Nominal  
Capacitance  
(8)Packaging Code  
Code  
3. Type & Dimensions  
(Unit:mm)  
(1)-1 L  
3.2±0.2  
(1)-2 W  
1.6±0.2  
(2) T  
1.6±0.2  
e
g
0.3 to 0.8  
1.5 min.  
4.Rated value  
(3) Temperature Characteristics  
(Public STD Code):X7R(EIA)  
Specifications and Test  
Methods  
(4)  
Rated  
Voltage  
(6)  
(5) Nominal  
Capacitance  
Capacitance  
Tolerance  
(Operating  
Temp. Range)  
Temp. coeff  
orCap. Change  
Temp. Range  
(Ref.Temp.)  
-55 to 125 °C  
(25 °C)  
DC 50 V  
4.7 uF  
±20 %  
-15 to 15 %  
-55 to 125 °C  
Soldering Method  
Flow/Reflow  
5.Package  
mark  
(8) Packaging  
Packaging Unit  
f180mm Reel  
EMBOSSED W8P4  
f330mm Reel  
L
2000 pcs./Reel  
6000 pcs./Reel  
K
EMBOSSED W8P4  
Product specifications in this catalog are as of Jun.5,2017,and are subject to change or obsolescence without notice.  
Please consult the approval sheet before ordering.  
Please read rating and !Cautions first.  
GJ831CR71H475MA12-01  
1
Specifications and Test Methods  
Test Method  
(Ref. Standard:JIS C 5101, IEC60384)  
No  
1
Item  
Rated Voltage  
Specification  
Shown in Rated value.  
The rated voltage is defined as the maximum voltage  
which may be applied continuously to the capacitor.  
When AC voltage is superimposed on DC voltage,  
VP-P or VO-P, whichever is larger, should be maintained  
within the rated voltage range.  
2
3
4
Appearance  
Dimension  
No defects or abnormalities.  
Visual inspection.  
Within the specified dimensions.  
No defects or abnormalities.  
Using Measuring instrument of dimension.  
Voltage proof  
Measurement Point  
Test Voltage  
:
Between the terminations  
250% of the rated voltage  
: 1s to 5 s  
:
Applied Time  
Charge/discharge current : 50mA max.  
5
Insulation Resistance(I.R.)  
C0.047µF:More than 10000MΩ  
C0.047µF:More than 500Ω·F  
C:Nominal Capacitance  
Measurement Point ꢀꢀ : Between the terminations  
Measurement Voltage : DC Rated Voltage  
Charging Time  
: 2 min  
Charge/discharge current : 50mA max.  
Measurement Temperature : Room Temperature  
6
7
8
Capacitance  
Shown in Rated value.  
0.025max.  
Measurement Temperature : Room Temperature  
Capacitance  
Frequency  
Voltage  
Dissipation Factor (D.F.)  
C10μF  
1.0+/-0.1kHz  
1.0+/-0.2Vrms  
Temperature  
No bias  
B3 : Within +/-10% (-25°C to +85°C)  
R7 : Within +/-15% (-55°C to +125°C)  
R6 : Within +/-15% (-55°C to +85°C)  
C8 : Within +/-22% (-55°C to +105°C)  
The capacitance change should be measured after 5 min  
at each specified temp. stage.  
Characteristics  
of Capacitance  
Capacitance value as a reference is the value in step 3.  
Applying Voltage(VDC)  
No bias  
Step  
Temperature(C)  
Reference Temp.+/-2  
Min.Operating Temp.+/-3  
Reference Temp.+/-2  
Max.Operating Temp.+/-3  
Reference Temp.+/-2  
1
2
3
4
5
· Initial measurement  
Perform a heat treatment at 150+0/-10°C for 1h and then  
let sit for 24+/-2h at room temperature,then measure.  
9
Adhesive Strength  
of Termination  
No removal of the terminations or other defect  
should occur.  
Solder the capacitor on the test substrate shown in Fig.3.  
Applied Forceꢀꢀꢀꢀ ꢀꢀ: 10N  
Holding Time  
: 10+/-1s  
Applied Direction : In parallel with the test substrate and vertical with  
the capacitor side.  
10 Vibration  
Appearance No defects or abnormalities.  
Capacitance Within the specified initial value.  
D.F. Within the specified initial value.  
Solder the capacitor on the test substrate shown in Fig.3.  
Kind of Vibration  
:
A simple harmonic motion  
10Hz to 55Hz to 10Hz (1min)  
: 1.5mm  
Total amplitude  
This motion should be applied for a period of 2h in each 3 mutually  
perpendicular directions(total of 6h).  
11 Substrate  
Bending test  
Appearance No defects or abnormalities.  
Solder the capacitor on the test substrate shown in Fig.1.  
Pressurization method : Shown in Fig.2  
Capacitance Within +/-10%  
Change  
Flexureꢀ  
ꢀꢀꢀ: 1mm  
Holding Time  
Soldering Method  
:
5+/-1s  
:
Reflow soldering  
JEMCGS-00303E  
2
Test Method  
(Ref. Standard:JIS C 5101, IEC60384)  
No  
Item  
Specification  
12 Solderability  
Test Method  
Flux  
:
Solder bath method  
Solution of rosin ethanol 25(mass)%  
80to 120for 10s to 30s  
: Sn-3.0Ag-0.5Cu  
75% of the terminations is to be soldered evenly and continuously.  
Preheat  
:
Solder  
Solder Temp.  
Immersion time  
: 245+/-5℃  
: 2+/-0.5s  
13 Resistance to  
Appearance No defects or abnormalities.  
Test Method  
Solder  
:
Solder bath method  
Sn-3.0Ag-0.5Cu  
270+/-5℃  
Soldering Heat  
:
:
Capacitance Within +/-7.5%  
Change  
Solder Temp.  
Immersion time  
Exposure Time  
Preheat  
: 10+/-0.5s  
D.F.  
Within the specified initial value.  
:
24+/-2h  
:
GJ831 size max.: 120to 150for 1 min  
GJ832 size ꢀꢀ : 100to 120for 1 min  
and 170to 200for 1 min  
I.R.  
Within the specified initial value.  
ꢀꢀꢀꢀ  
Voltage proof No defects.  
· Initial measurement  
Perform a heat treatment at 150+0/-10°C for 1h and then  
let sit for 24+/-2h at room temperature,then measure.  
14  
Appearance No defects or abnormalities.  
Solder the capacitor on the test substrate shown in Fig.3.  
Temperature  
Sudden Change  
Capacitance Within +/-7.5%  
Change  
Perform the 5 cycles according to the four heat treatments  
shown in the following table.  
D.F.  
Within the specified initial value.  
Step  
Temp.(C)  
Min.Operating Temp.+0/-3  
Room Temp.  
Time (min)  
30+/-3  
2 to 3  
1
2
3
4
I.R.  
Within the specified initial value.  
Voltage proof No defects.  
30+/-3  
2 to 3  
Max.Operating Temp.+3/-0  
Room Temp  
Exposure Time  
: 24+/-2h  
· Initial measurement  
Perform a heat treatment at 150+0/-10°C for 1h and then  
let sit for 24+/-2h at room temperature,then measure.  
15  
Appearance No defects or abnormalities.  
Solder the capacitor on the test substrate shown in Fig.3.  
High  
Temperature  
High Humidity  
(Steady)  
Capacitance Within +/-12.5%  
Change  
Test Temperature  
Test Humidity  
Test Time  
: 40+/-2℃  
: 90%RH to 95%RH  
: 500+/-12h  
D.F.  
0.05 max.  
Applied Voltage  
: DC Rated Voltage  
I.R.  
More than 500MΩ or 25Ω·F (Whichever is smaller)  
Charge/discharge current : 50mA max.  
Exposure Time : 24+/-2h  
16  
Appearance No defects or abnormalities.  
Solder the capacitor on the test substrate shown in Fig.3.  
Durability  
Capacitance Within +/-12.5%  
Change  
Test Temperature  
Test Time  
:
Max. Operating Temp. +/-3℃  
1000+/-12h  
:
D.F.  
0.05 max.  
Applied Voltage  
:
200%* of the rated voltage  
Charge/discharge current : 50mA max.  
I.R.  
More than 1,000MΩ or 50Ω·F (Whichever is smaller)  
Exposure Time  
: 24+/-2h  
Initial measurement  
Apply 200%* of the rated DC voltage at the max. operating  
temp. +/-3°C for 1h.  
Remove and set for 24+/-2h at room temperature.  
Perform initial measurement.  
* GJ821B B3/R7 1H 105 ,  
GJ831C B3/R7 1H 475 ,  
GJ832ER7YA106ꢀꢀꢀꢀꢀ only : 150%* of the rated voltage  
JEMCGS-00303E  
3
Substrate Bending test  
Test substrate  
Material  
: Copper-clad laminated sheets for PCBs (Glass fabric base, epoxy resin)  
Thickness : 1.6mm  
Copper foil thickness : 0.035mm  
ꢀꢀꢀꢀꢀꢀꢀ: Solder resist (Coat with heat resistant resin for solder)  
b
Land  
f4.5  
Dimension(mm)  
Type  
a
b
c
GJ821  
GJ831  
GJ832  
1.2  
2.2  
2.2  
4.0  
5.0  
5.0  
1.65  
2.0  
2.9  
a
100  
Fig.1  
Kind of Solder : Sn-3.0Ag-0.5Cu  
Pressurization method  
(in mm)  
20  
Pressurization  
speed  
1.0mm/s  
50 min.  
Pressurize  
R5  
Flexure  
Capacitance meter  
45 45  
Fig.2  
(in mm)  
Adhesive Strength of Termination, Vibration, Temperature Sudden Change, High Temperature High Humidity(Steady) , Durability  
Test substrate  
Material  
: Copper-clad laminated sheets for PCBs (Glass fabric base, epoxy resin)  
Thickness : 1.6mm  
Copper foil thickness : 0.035mm  
Kind of Solder : Sn-3.0Ag-0.5Cu  
Land Dimensions  
Chip Capacitor  
Land  
Dimension(mm)  
Type  
a
b
c
GJ821  
GJ831  
GJ832  
1.2  
2.2  
2.2  
4.0  
5.0  
5.0  
1.65  
2.0  
2.9  
a
Solder Resist  
b
Fig.3  
JEMCGS-00303E  
4
Package  
GJ8 Type  
1.Tape Carrier Packaging(Packaging Code:D/L/J/K)  
1.1 Minimum Quantity(pcs./reel)  
φ180mm reel  
φ330mm reel  
Type  
GJ818  
GJ821  
GJ831  
GJ832  
Paper Tape Plastic Tape Paper Tape Plastic Tape  
Code:D  
4000  
Code:L  
Code:J  
10000  
Code:K  
8
A/B  
9
C
E
3000  
10000  
4000  
10000  
2000  
1000  
6000  
4000  
1.2 Dimensions of Tape  
(1)GJ818/GJ831 <Paper Tape CODE:D/J>  
(in:mm)  
4.0±0.1  
4.0±0.1  
2.0±0.1  
+0.1  
-0  
φ1.5  
t
Dimensions(Chip)  
W
Type  
A
B
t
L
T
8
9
1.6±0.15  
3.2±0.2  
0.8±0.15  
1.6±0.2  
0.8±0.15  
0.85±0.1  
1.05±0.10  
2.00±0.20  
1.85±0.10  
3.60±0.20  
GJ818  
GJ831  
1.15 max.  
JEMCGP-00325J  
5
Package  
GJ8 Type  
(2)GJ821/GJ831/GJ832 <Plastic Tape CODE:L/K>  
(in:mm)  
4.0±0.1  
4.0±0.1  
2.0±0.1  
0.25±0.1(T2.0mm)  
0.3±0.1(T2.5mm)  
+0.1  
φ1.5  
-0  
t
Dimensions(Chip)  
W
Type  
A
B
t
L
T
A
B
2.0±0.2 1.25±0.2 1.0±0.2  
2.0±0.1 1.25±0.1 1.25±0.1  
2.0±0.2 1.25±0.2 1.25±0.2  
1.50±0.20  
1.45±0.20  
1.50±0.20  
1.90±0.20  
2.10±0.20  
2.80±0.20  
2.30±0.20  
2.25±0.20  
2.30±0.20  
3.50±0.20  
3.60±0.20  
3.50±0.20  
1.7 max.  
2.0 max.  
GJ821  
3.2±0.2  
1.6±0.2  
1.6±0.3  
2.5±0.2  
1.6±0.2  
1.6±0.3  
2.5±0.2  
GJ831 C  
GJ832 E  
2.5 max.  
3.7 max.  
3.2±0.3  
JEMCGP-00325J  
6
Package  
GJ8 Type  
Fig.1 Package Chips  
(in:mm)  
Chip  
Fig.2 Dimensions of Reel  
2.0±0.5  
φ21±0.8  
10±1.5  
16.5 max.  
Fig.3 Taping Diagram  
Top Tape : Thickness 0.06  
Feeding Hole :As specified in 1.2.  
Hole for Chip : As specified in 1.2.  
Bottom Tape :Thickness 0.05  
(Only a bottom tape existence )  
Base Tape : As specified in 1.2.  
JEMCGP-00325J  
7
Package  
GJ8 Type  
1.3 Tapes for capacitors are wound clockwise shown in Fig.3.  
(The sprocket holes are to the right as the tape is pulled toward the user.)  
1.4 Part of the leader and part of the vacant section are attached as follows.  
Tail vacant Section  
Chip-mounting Unit Leader vacant Section  
(in:mm)  
Leader Unit  
(Top Tape only)  
Direction  
of Feed  
160 min.  
190 min.  
210 min.  
1.5 Accumulate tolerance of sprocket holes pitch = ±0.3mm / 10 pitch  
1.6 Chip in the tape is enclosed by top tape and bottom tape as shown in Fig.1.  
1.7 The top tape and base tape are not attached at the end of the tape for a minimum of 5 pitches.  
1.8 There are no jointing for top tape and bottom tape.  
1.9 There are no fuzz in the cavity.  
1.10 Break down force of top tape : 5N min.  
Break down force of bottom tape : 5N min. (Only a bottom tape existence )  
1.11 Reel is made by resin and appeaser and dimension is shown in Fig 2.  
There are possibly to change the material and dimension due to some impairment.  
1.12 Peeling off force : 0.1N to 0.6N in the direction as shown below.  
Top tape  
165180°  
1.13 Label that show the customer parts number, our parts number, our company name, inspection  
number and quantity, will be put in outside of reel.  
JEMCGP-00325J  
8
!
Caution  
Limitation of Applications  
Please contact us before using our products for the applications listed below which require especially high reliability  
for the prevention of defects which might directly cause damage to the third party's life, body or property.  
ꢀꢀꢀ①Aircraft equipment Aerospace equipment Undersea equipment Power plant control equipment  
ꢀꢀꢀ⑤Medical equipment Transportation equipment(vehicles,trains,ships,etc.) Traffic signal equipment  
ꢀꢀꢀ⑧Disaster prevention / crime prevention equipment  
Data-processing equipment  
ꢀꢀꢀ⑩Application of similar complexity and/or reliability requirements to the applications listed in the above.  
Storage and Operation condition  
1. The performance of chip multilayer ceramic capacitors may be affected by the storage conditions.  
1-1. Store the capacitors in the following conditions:  
Room Temperature of +5to +40and a Relative Humidity of 20% to 70%.  
(1) High temperature and humidity conditions may accelerate the deterioration of solderability due to oxidation  
of the terminal electrodes and deterioration of taping/packaging performance.  
Therefore, maintain the appropriate storage temperature and humidity.  
(2) Prolonged storage may cause oxidation of the electrodes and deterioration of the packaging materials.  
If more than six months have elapsed since delivery, check the mounting before use.  
If more than one year has elapsed since delivery, also check the solderability before use.  
Even if the storage period is short, do not exceed the specified atmospheric conditions.  
(3) Store the capacitors in the original packaging without opening the smallest packing unit.  
Do not exceed the above atmospheric conditions for any length of time.  
1-2. Corrosive gas can react with the termination (external) electrodes or lead wires of capacitors, and result  
in poor solderability. Do not store the capacitors in an atmosphere consisting of corrosive gas (e.g.,hydrogen  
sulfide, sulfur dioxide, chlorine, ammonia gas etc.).  
1-3. Due to moisture condensation caused by rapid humidity changes, or the photochemical change caused  
by direct sunlight on the terminal electrodes and/or the resin/epoxy coatings, the solderability and electrical  
performance may deteriorate. Do not store capacitors under direct sunlight or in high huimidity conditions.  
Rating  
1.Temperature Dependent Characteristics  
1. The electrical characteristics of the capacitor can change with temperature.  
1-1. For capacitors having larger temperature dependency, the capacitance may change with temperature  
changes. The following actions are recommended in order to ensure suitable capacitance values.  
(1) Select a suitable capacitance for the operating temperature range.  
(2) The capacitance may change within the rated temperature.  
When you use a high dielectric constant type capacitor in a circuit that needs a tight (narrow) capacitance  
tolerance (e.g., a time-constant circuit), please carefully consider the temperature characteristics, and  
carefully confirm the various characteristics in actual use conditions and the actual system.  
[Example of Temperature Caracteristics X7R(R7)]  
[Example of Temperature Characteristics X5R(R6)]  
Sample: 0.1μF, Rated Voltage 50VDC  
Sample: 22μF, Rated Voltage 4VDC  
20  
1
1
20  
15  
10  
5
0
-
-5  
-1
-1
-2
-10  
-15  
-20  
-75  
-50  
-25  
0
25  
50  
75  
100  
-75  
-50  
-25  
0
25  
50  
75  
100 125 150  
Temperature (C)  
Temperature (C)  
JEMCGC-00326E  
9
! Caution  
2.Measurement of Capacitance  
1. Measure capacitance with the voltage and frequency specified in the product specifications.  
1-1. The output voltage of the measuring equipment may decrease occasionally when capacitance is high.  
Please confirm whether a prescribed measured voltage is impressed to the capacitor.  
1-2. The capacitance values of high dielectric constant type capacitors change depending on the AC voltage applied.  
Please consider the AC voltage characteristics when selecting a capacitor to be used in a AC circuit.  
3.Applied Voltage  
1. Do not apply a voltage to the capacitor that exceeds the rated voltage as called out in the specifications.  
1-1. Applied voltage between the terminals of a capacitor shall be less than or equal to the rated voltage.  
(1) When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated DC voltage.  
When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed the rated DC voltage.  
(2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC voltage.  
Typical Voltage Applied to the DC capacitor  
DC Voltage  
DC Voltage+AC  
AC Voltage  
Pulse Voltage  
0
E
E
E
E
0
0
0
(EMaximum possible applied voltage.)  
1-2. Influence of over voltage  
Over voltage that is applied to the capacitor may result in an electrical short circuit caused by the breakdown  
of the internal dielectric layers .  
The time duration until breakdown depends on the applied voltage and the ambient temperature.  
4.Type of Applied Voltage and Self-heating Temperature  
1.Confirm the operating conditions to make sure that no large current is flowing into the capacitor due to the  
continuous application of an AC voltage or pulse voltage.  
When a DC rated voltage product is used in an AC voltage circuit or a pulse voltage circuit, the AC current  
or pulse current will flow into the capacitor; therefore check the self-heating condition.  
Please confirm the surface temperature of the capacitor so that the temperature remains within the upper limits  
of the operating temperature, including the rise in temperature due to self-heating. When the capacitor is  
used with a high-frequency voltage or pulse voltage, heat may be generated by dielectric loss.  
<Applicable to Rated Voltage of less than 100VDC>  
The load should be contained so that the self-heating  
of the capacitor body remains below 20°C ,  
[Example of Temperature Rise (Heat Generation) in Chip  
Multilayer Ceramic Capacitors in Contrast to Ripple Current]  
Sample: R(R1) characteristics 10μF, Rated voltage: DC10V  
when measuring at an ambient temperature of 25°C.  
Ripple Current  
100  
10  
100kHz  
500kHz  
1MHz  
1
0
1
2
3
4
5
6
Current (Ar.m.s.)  
JEMCGC-00326E  
10  
! Caution  
5. DC Voltage and AC Voltage Characteristic  
1. The capacitance value of a high dielectric constant type  
capacitor changes depending on the DC voltage applied.  
Please consider the DC voltage characteristics when a  
capacitor is selected for use in a DC circuit.  
[Example of DC Voltage Characteristics]  
Sample: X7R(R7) Characteristics 0.1μF, Rated Voltage 50VDC  
2
0
-2
-4
-6
-8
1-1. The capacitance of ceramic capacitors may change  
sharply depending on the applied voltage. (See figure)  
Please confirm the following in order to secure the  
capacitance.  
(1) Determine whether the capacitance change caused  
by the applied voltage is within the allowed range .  
(2) In the DC voltage characteristics, the rate of  
capacitance change becomes larger as voltage  
increases, even if the applied voltage is below  
the rated voltage. When a high dielectric constant  
type capacitor is used in a circuit that requires a  
tight (narrow) capacitance tolerance (e.g., a time  
constant circuit), please carefully consider the  
voltage characteristics, and confirm the various  
characteristics in the actual operating conditions  
-10
0
10  
20  
30  
40  
50  
DC Voltage (V)  
[Example of AC Voltage Characteristics]  
Sample: X7R(R7) Characteristics 10μF, Rated Voltage 6.3VDC  
30  
20  
10  
0
of the system.  
-10  
-20  
2. The capacitance values of high dielectric  
constant type capacitors changes depending  
on the AC voltage applied.  
-30  
-40  
-50  
-60  
Please consider the AC voltage characteristics  
when selecting a capacitor to be used in a  
AC circuit.  
0
0.5  
1
1.5  
2
AC Voltage (Vr.m.s.)  
6. Capacitance Aging  
[Example of Change Over Time (Aging characteristics) ]  
1. The high dielectric constant type capacitors  
have an Aging characteristic in which the capacitance  
value decreases with the passage of time.  
20  
10  
0
When you use a high dielectric constant type  
capacitors in a circuit that needs a tight (narrow)  
capacitance tolerance (e.g., a time-constant circuit),  
please carefully consider the characteristics  
of these capacitors, such as their aging, voltage,  
and temperature characteristics. In addition,  
check capacitors using your actual appliances  
at the intended environment and operating conditions.  
-10  
C0G(5C)  
-20  
X7R(R7)  
-30  
X5R(R6)  
-40  
10  
100  
1000  
10000  
Time(h)  
7.Vibration and Shock  
1. Please confirm the kind of vibration and/or shock, its condition, and any generation of resonance.  
Please mount the capacitor so as not to generate resonance, and do not allow any impact on the terminals.  
2. Mechanical shock due to being dropped may cause damage or  
a crack in the dielectric material of the capacitor.  
Do not use a dropped capacitor because the quality and reliability  
Crack  
may be deteriorated.  
Floor  
3. When printed circuit boards are piled up or handled, the corner  
of another printed circuit board  
Mounting printed circuit board  
Crack  
should not be allowed to hit the capacitor in order to avoid  
a crack or other damage to the capacitor.  
JEMCGC-00326E  
11  
! Caution  
Soldering and Mounting  
1.Mounting Position  
1. Confirm the best mounting position and direction that minimizes the stress imposed on the capacitor during flexing  
or bending the printed circuit board.  
1-1.Choose a mounting position that minimizes the stress imposed on the chip during flexing or bending of the board.  
[Component Direction]  
Locate chip horizontal to the  
direction in which stress acts.  
(Bad Example)  
(Good Example)  
[Chip Mounting Close to Board Separation Point]  
It is effective to implement the following measures, to reduce stress in separating the board.  
It is best to implement all of the following three measures; however, implement as many measures as possible  
to reduce stress.  
Contents of Measures  
Stress Level  
A>D *1  
A>B  
(1) Turn the mounting direction of the component parallel to the board separation surface.  
(2) Add slits in the board separation part.  
(3) Keep the mounting position of the component away from the board separation surface.  
A>C  
C
Perforation  
B
D
A
Slit  
*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.  
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.  
[Mounting Capacitors Near Screw Holes]  
When a capacitor is mounted near a screw hole, it may be affected by the board deflection that occurs during  
the tightening of the screw. Mount the capacitor in a position as far away from the screw holes as possible.  
Recommended  
Screw Hole  
2.Information before Mounting  
1. Do not re-use capacitors that were removed from the equipment.  
2. Confirm capacitance characteristics under actual applied voltage.  
3. Confirm the mechanical stress under actual process and equipment use.  
4. Confirm the rated capacitance, rated voltage and other electrical characteristics before assembly.  
5. Prior to use, confirm the solderability of capacitors that were in long-term storage.  
6. Prior to measuring capacitance, carry out a heat treatment for capacitors that were in long-term storage.  
7.The use of Sn-Zn based solder will deteriorate the reliability of the MLCC.  
Please contact our sales representative or product engineers on the use of Sn-Zn based solder in advance.  
JEMCGC-00326E  
12  
!
Caution  
3.Maintenance of the Mounting (pick and place) Machine  
1. Make sure that the following excessive forces are not applied to the capacitors.  
Check the mounting in the actual device under actual use conditions ahead of time.  
1-1. In mounting the capacitors on the printed circuit board, any bending force against them shall be kept  
to a minimum to prevent them from any damage or cracking. Please take into account the following precautions  
and recommendations for use in your process.  
(1) Adjust the lowest position of the pickup nozzle so as not to bend the printed circuit board.  
[Incorrect]  
[Correct]  
Suction Nozzle  
Deflection  
Board  
Board Guide  
Support Pin  
2.Dirt particles and dust accumulated in the suction nozzle and suction mechanism prevent the nozzle from  
moving smoothly. This creates excessive force on the capacitor during mounting, causing cracked chips.  
Also, the locating claw, when worn out, imposes uneven forces on the chip when positioning, causing cracked chips.  
The suction nozzle and the locating claw must be maintained, checked and replaced periodically.  
JEMCGC-00326E  
13  
! Caution  
4-1.Reflow Soldering  
1. When sudden heat is applied to the components, the  
mechanical strength of the components will decrease  
because a sudden temperature change causes  
deformation inside the components. In order to prevent  
mechanical damage to the components, preheating is  
required for both the components and the PCB.  
Preheating conditions are shown in table 1. It is required to  
keep the temperature differential between the solder and  
the components surface (ΔT) as small as possible.  
[Standard Conditions for Reflow Soldering]  
Temperature()  
Soldering  
Peak Temperature  
Gradual  
Cooling  
220℃  
ΔT  
190℃  
170℃  
150℃  
Preheating  
Time  
2. When components are immersed in solvent after mounting,  
be sure to maintain the temperature difference (ΔT)  
between the component and the solvent within the range  
shown in the table 1.  
60-120 seconds 30-60 seconds  
[Allowable Reflow Soldering Temperature and Time]  
280  
270  
260  
Table 1  
ChipDimension(L/W)Code Temperature Differential  
Series  
250  
240  
230  
220  
18/21/31  
32  
ΔT190℃  
ΔT130℃  
GJ8  
GJ8  
0
30  
60  
90  
120  
Soldering Time(s)  
In the case of repeated soldering, the accumulated  
soldering time must be within the range shown above.  
Recommended Conditions  
Peak Temperature  
Lead Free Solder  
240 to 260℃  
Air or N2  
Atmosphere  
Lead Free Solder: Sn-3.0Ag-0.5Cu  
3. When a capacitor is mounted at a temperature lower than the peak reflow temperature recommended by the  
solder manufacturer, the following quality problems can occur. Consider factors such as the placement of  
peripheral components and the reflow temperature setting to prevent the capacitor’s reflow temperature from  
dropping below the peak temperature specified. Be sure to evaluate the mounting situation beforehand and  
verify that none of the following problems occur.  
Drop in solder wettability  
Solder voids  
Possible occurrence of whiskering  
Drop in bonding strength  
Drop in self-alignment properties  
Possible occurrence of tombstones and/or shifting on the land patterns of the circuit board  
4. Optimum Solder Amount for Reflow Soldering  
4-1. Overly thick application of solder paste results in a excessive solder fillet height.  
This makes the chip more susceptible to mechanical and thermal stress on the board and may cause the chips to crack.  
4-2. Too little solder paste results in a lack of adhesive strength on the termination, which may result in chips breaking loose  
from the PCB.  
4-3. Please confirm that solder has been applied smoothly to the termination.  
Inverting the PCB  
Make sure not to impose any abnormal mechanical shocks to the PCB.  
JEMCGC-00326E  
14  
Caution  
!
4-2.Flow Soldering  
1. Do not apply flow soldering to chips not listed in Table 2.  
ꢀꢀꢀꢀꢀ[Standard Conditions for Flow Soldering]  
Temperature()  
Soldering  
Peak  
Temperature  
Table 2  
Soldering  
ChipDimension(L/W)Code Temperature Differential  
18/21/31  
ΔT150℃  
Series  
GJ8  
Gradual  
Cooling  
ΔT  
Preheating  
Peak  
Temperature  
(Except for GJ821BR61E106K,GJ831CC81E105K)  
Preheating  
Time  
5 seconds max.  
30-90 seconds  
2. When sudden heat is applied to the components, the  
mechanical strength of the components will decrease  
because a sudden temperature change causes  
deformation inside the components. In order to prevent  
mechanical damage to the components, preheating is  
required for both of the components and the PCB.  
Preheating conditions are shown in table 2. It is required to  
keep the temperature differential between the solder and  
the components surface (ΔT) as low as possible.  
[Allowable Flow Soldering Temperature and Time]  
280  
270  
260  
3. Excessively long soldering time or high soldering  
temperature can result in leaching of the terminations,  
causing poor adhesion or a reduction in capacitance value  
due to loss of contact between the inner electrodes and terminations.  
250  
240  
230  
220  
4. When components are immersed in solvent after mounting,  
be sure to maintain the temperature differential (ΔT)  
between the component and solvent within the range  
shown in the table 2.  
0
10  
20  
30  
40  
Soldering Time(s)  
In the case of repeated soldering, the accumulated  
soldering time must be within the range shown above.  
Recommended Conditions  
Lead Free Solder  
Preheating Peak Temperature  
Soldering Peak Temperature  
100 to 120℃  
250 to 260℃  
Air or N2  
Atmosphere  
Lead Free Solder: Sn-3.0Ag-0.5Cu  
5. Optimum Solder Amount for Flow Soldering  
Up to Chip Thickness  
5-1. The top of the solder fillet should be lower than the  
thickness of the components. If the solder amount is  
excessive, the risk of cracking is higher during  
board bending or any other stressful condition.  
in section  
Adhesive  
JEMCGC-00326E  
15  
Caution  
!
4-3.Correction of Soldered Portion  
When sudden heat is applied to the capacitor, distortion caused by the large temperature difference occurs internally,  
and can be the cause of cracks. Capacitors also tend to be affected by mechanical and thermal stress depending  
on the board preheating temperature or the soldering fillet shape, and can be the cause of cracks.  
Please refer to "1. PCB Design" or "3. Optimum solder amount" for the solder amount and the fillet shapes.  
1. Correction with a Soldering Iron  
1-1. In order to reduce damage to the capacitor, be sure to preheat the capacitor and the mounting board.  
Preheat to the temperature range shown in Table 3. A hot plate, hot air type preheater, etc. can be used for preheating.  
1-2. After soldering, do not allow the component/PCB to cool down rapidly.  
1-3. Perform the corrections with a soldering iron as quickly as possible. If the soldering iron is applied too long,  
there is a possibility of causing solder leaching on the terminal electrodes, which will cause deterioration of the  
adhesive strength and other problems.  
Table 3  
ChipDimension  
(L/W)Code  
Temperature of  
Soldering Iron Tip  
Preheating  
Temperature  
Temperature  
Differential(ΔT)  
Series  
Atmosphere  
GJ8  
18/21/31  
32  
350max.  
280max.  
150min.  
150min.  
ΔT190℃  
ΔT130℃  
Air  
Air  
GJ8  
Lead Free Solder: Sn-3.0Ag-0.5Cu  
* Please manage Δ T in the temperature of soldering iron and the preheating temperature.  
2. Correction with Spot Heater  
Compared to local heating with a soldering iron, hot air heating by a spot heater heats the overall component  
and board, therefore, it tends to lessen the thermal shock. In the case of a high density mounted board,  
a spot heater can also prevent concerns of the soldering iron making direct contact with the component.  
2-1. If the distance from the hot air outlet of the spot heater to the component is too close, cracks may occur due to  
thermal shock. To prevent this problem, follow the conditions shown in Table 4.  
2-2. In order to create an appropriate solder fillet shape, it is recommended that hot air be applied at the angle shown  
in Figure 1.  
Table 4  
Distance  
Hot Air Application angle  
5mm or more  
45° *Figure 1  
Hot Air Temperature Nozzle Outlet 400°C max.  
Less than 10 seconds  
Application Time  
(3216M / 1206 size or smaller)  
Less than 30 seconds  
(3225M / 1210 size)  
(3216M , 3225M : Metric size code)  
[Figure 1]  
One-hole Nozzle  
an Angle of 45ꢀ  
3. Optimum solder amount when re-working with a soldering iron  
3-1. If the solder amount is excessive, the risk of cracking is higher  
ꢀꢀꢀ during board bending or any other stressful condition.  
Too little solder amount results in a lack of adhesive strength  
on the termination, which may result in chips breaking  
loose from the PCB.  
SolderAmount  
in section  
Please confirm that solder has been applied smoothly is  
and rising to the end surface of the chip.  
3-2. A soldering iron with a tip of ø3mm or smaller should be used.  
It is also necessary to keep the soldering iron from touching  
the components during the re-work.  
3-3. Solder wire with ø0.5mm or smaller is required for soldering.  
JEMCGC-00326E  
16  
! Caution  
5.Washing  
Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips  
or broken solder joints. Before starting your production process, test your cleaning equipment / process to insure  
it does not degrade the capacitors.  
6.Electrical Test on Printed Circuit Board  
1. Confirm position of the support pin or specific jig, when inspecting the electrical performance of a  
capacitor after mounting on the printed circuit board.  
1-1. Avoid bending the printed circuit board by the pressure of a test-probe, etc.  
The thrusting force of the test probe can flex the PCB, resulting in cracked chips or open solder  
joints. Provide support pins on the back side of the PCB to prevent warping or flexing.  
Install support pins as close to the test-probe as possible.  
1-2. Avoid vibration of the board by shock when a test -probe contacts a printed circuit board.  
[Not Recommended]  
[Recommended]  
Support Pin  
Peeling  
Test-probe  
Test-probe  
7.Printed Circuit Board Cropping  
1. After mounting a capacitor on a printed circuit board, do not apply any stress to the capacitor that  
caused bending or twisting the board.  
1-1. In cropping the board, the stress as shown may cause the capacitor to crack.  
Cracked capacitors may cause deterioration of the insulation resistance, and result in a short.  
Avoid this type of stress to a capacitor.  
[Bending]  
[Twisting]  
2. Check the cropping method for the printed circuit board in advance.  
2-1. Printed circuit board cropping shall be carried out by using a jig or an apparatus (Disc separator, router  
type separator, etc.) to prevent the mechanical stress that can occur to the board.  
Board Separation Apparatus  
Hand Separation  
Nipper Separation  
Board Separation Method  
(1) Board Separation Jig  
2) Disc Separator  
3) Router Type Separator  
Level of stress on board  
Recommended  
High  
×
Medium  
*  
Medium  
*  
Low  
· Board handling  
· Layout of slits  
· Board bending direction · Design of V groove  
Hand and nipper  
separation apply a high  
level of stress.  
· Board handling  
Notes  
Board handling  
· Layout of capacitors  
· Arrangement of blades  
· Controlling blade life  
Use another method.  
* When a board separation jig or disc separator is used, if the following precautions are not observed,  
a large board deflection stress will occur and the capacitors may crack.  
Use router type separator if at all possible.  
JEMCGC-00326E  
17  
! Caution  
(1) Example of a suitable jig  
[In the case of Single-side Mounting]  
An outline of the board separation jig is shown as follows.  
Recommended example: Stress on the component mounting position can be minimized by holding the  
portion close to the jig, and bend in the direction towards the side where the capacitors are mounted.  
Not recommended example: The risk of cracks occurring in the capacitors increases due to large stress  
being applied to the component mounting position, if the portion away from the jig is held and bent in the  
direction opposite the side where the capacitors are mounted.  
[Outline of jig]  
[Hand Separation]  
Recommended  
Not recommended  
Direction of  
load  
Direction of load  
Load point  
Printed Circuit Board  
Printed circuit  
board  
V-groove  
Component  
Components  
Printed circuit  
board  
Load point  
Board Cropping Jig  
[In the case of Double-sided Mounting]  
Since components are mounted on both sides of the board, the risk of cracks occurring can not be avoided with the  
above method. Therefore, implement the following measures to prevent stress from being applied to the components.  
(Measures)  
(1) Consider introducing a router type separator.  
If it is difficult to introduce a router type separator, implement the following measures.  
(Refer to item 1. Mounting Position)  
(2) Mount the components parallel to the board separation surface.  
(3) When mounting components near the board separation point, add slits in the separation position  
near the component.  
(4) Keep the mounting position of the components away from the board separation point.  
(2) Example of a Disc Separator  
An outline of a disc separator is shown as follows. As shown in the Principle of Operation, the top  
blade and bottom blade are aligned with the V-grooves on the printed circuit board to separate the board.  
In the following case, board deflection stress will be applied and cause cracks in the capacitors.  
(1) When the adjustment of the top and bottom blades are misaligned, such as deviating in the top-bottom,  
left-right or front-rear directions  
(2) The angle of the V groove is too low, depth of the V groove is too shallow, or the V groove is misaligned  
top-bottom  
IF V groove is too deep, it is possible to brake when you handle and carry it. Carefully design depth of the  
V groove with consideration about strength of material of the printed circuit board.  
[ Outline of Machine ]  
Top Blade  
[ Principle of Operation ]  
Top Blade  
[ Cross-section Diagram ]  
Printed Circuit Board  
V-groove  
Bottom Blade  
Printed Circuit Board  
[Disc Separator]  
Recommended  
Top Blade  
V-groove  
Not recommended  
Top-bottom Misalignment Left-right Misalignment  
Front-rear Misalignment  
Top Blade  
Top Blade  
Top Blade  
Bottom Blade  
Bottom Blade  
Bottom Blade  
Bottom Blade  
[V-groove Design]  
Example of Recommended  
Not Recommended  
Low-Angle  
Depth too Shallow  
V-groove Design  
Left-right Misalignment  
Depth too Deep  
JEMCGC-00326E  
18  
!
Caution  
(3) Example of Router Type Separator  
[ Outline Drawing ]  
Router  
The router type separator performs cutting by a router  
rotating at a high speed. Since the board does not  
bend in the cutting process, stress on the board can  
be suppressed during board separation.  
When attaching or removing boards to/from the router type  
separator, carefully handle the boards to prevent bending.  
8. Assembly  
1. Handling  
If a board mounted with capacitors is held with one hand, the board may bend.  
Firmly hold the edges of the board with both hands when handling.  
If a board mounted with capacitors is dropped, cracks may occur in the capacitors.  
Do not use dropped boards, as there is a possibility that the quality of the capacitors may be impaired.  
2. Attachment of Other Components  
2-1. Mounting of Other Components  
Pay attention to the following items, when mounting other components on the back side of the board after  
capacitors have been mounted on the opposite side.  
When the bottom dead point of the suction nozzle is set too low, board deflection stress may be applied  
to the capacitors on the back side (bottom side), and cracks may occur in the capacitors.  
· After the board is straightened, set the bottom dead point of the nozzle on the upper surface of the board.  
· Periodically check and adjust the bottom dead point.  
Suction Nozzle  
2-2. Inserting Components with Leads into Boards  
When inserting components (transformers, IC, etc.) into boards, bending the board may cause cracks in the  
capacitors or cracks in the solder. Pay attention to the following.  
· Increase the size of the holes to insert the leads, to reduce the stress on the board during insertion.  
· Fix the board with support pins or a dedicated jig before insertion.  
· Support below the board so that the board does not bend. When using support pins on the board,  
periodically confirm that there is no difference in the height of each support pin.  
Component with Leads  
2-3. Attaching/Removing Sockets and/or connectors  
The board may bend when a socket and/or connector are attached or removed.  
Plan the work so that the board does not bend when a socket and/or connector are attached or removed.  
Socket  
2-4. Tightening Screws  
The board may be bent, when tightening screws, etc. during the attachment of the board to a shield or  
chassis. Pay attention to the following items before performing the work.  
· Plan the work to prevent the board from bending.  
· Use a torque screwdriver, to prevent over-tightening of the screws.  
· The board may bend after mounting by reflow soldering, etc. Please note, as stress may be applied  
to the chips by forcibly flattening the board when tightening the screws.  
Screwdriver  
JEMCGC-00326E  
19  
! Caution  
Others  
1. Under Operation of Equipment  
1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of an electric shock.  
1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit).  
Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.  
1-3. Confirm the environment in which the equipment will operate is under the specified conditions.  
Do not use the equipment under the following environments.  
(1) Being spattered with water or oil.  
(2) Being exposed to direct sunlight.  
(3) Being exposed to ozone, ultraviolet rays, or radiation.  
(4) Being exposed to toxic gas (e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.)  
(5) Any vibrations or mechanical shocks exceeding the specified limits.  
(6) Moisture condensing environments.  
1-4. Use damp proof countermeasures if using under any conditions that can cause condensation.  
2. Others  
2-1. In an Emergency  
(1) If the equipment should generate smoke, fire, or smell, immediately turn off or unplug the equipment.  
If the equipment is not turned off or unplugged, the hazards may be worsened by supplying continuous power.  
(2) In this type of situation, do not allow face and hands to come in contact with the capacitor or burns may be caused  
by the capacitor's high temperature.  
2-2. Disposal of waste  
When capacitors are disposed of, they must be burned or buried by an industrial waste vendor with the appropriate  
licenses.  
2-3. Circuit Design  
(1) Addition of Fail Safe Function  
Capacitors that are cracked by dropping or bending of the board may cause deterioration of the  
insulation resistance, and result in a short. If the circuit being used may cause an electrical shock,  
smoke or fire when a capacitor is shorted, be sure to install fail-safe functions, such as a fuse,  
to prevent secondary accidents.  
(2) This series are not safety standard certified products.  
2-4. Remarks  
Failure to follow the cautions may result, worst case, in a short circuit and smoking when the product is used.  
The above notices are for standard applications and conditions. Contact us when the products are used in special  
mounting conditions.  
Select optimum conditions for operation as they determine the reliability of the product after assembly.  
The data herein are given in typical values, not guaranteed ratings.  
JEMCGC-00326E  
20  
Notice  
Rating  
1.Operating Temperature  
1. The operating temperature limit depends on the capacitor.  
1-1. Do not apply temperatures exceeding the maximum operating temperature.  
It is necessary to select a capacitor with a suitable rated temperature that will cover the operating temperature range.  
It is also necessary to consider the temperature distribution in equipment and the seasonal temperature variable  
factor.  
1-2. Consider the self-heating factor of the capacitor  
The surface temperature of the capacitor shall not exceed the maximum operating temperature including self-heating.  
2.Atmosphere Surroundings (gaseous and liquid)  
1. Restriction on the operating environment of capacitors.  
1-1. Capacitors, when used in the above, unsuitable, operating environments may deteriorate due to the corrosion  
of the terminations and the penetration of moisture into the capacitor.  
1-2. The same phenomenon as the above may occur when the electrodes or terminals of the capacitor are subject  
to moisture condensation.  
1-3. The deterioration of characteristics and insulation resistance due to the oxidization or corrosion of terminal  
ꢀꢀelectrodes may result in breakdown when the capacitor is exposed to corrosive or volatile gases or solvents  
for long periods of time.  
3.Piezo-electric Phenomenon  
1. When using high dielectric constant type capacitors in AC or pulse circuits, the capacitor itself vibrates  
at specific frequencies and noise may be generated.  
Moreover, when the mechanical vibration or shock is added to capacitor, noise may occur.  
JEMCGC-00326E  
21  
Notice  
Soldering and Mounting  
1.PCB Design  
1. Notice for Pattern Forms  
1-1. Unlike leaded components, chip components are susceptible to flexing stresses since they are mounted  
directly on the substrate.  
They are also more sensitive to mechanical and thermal stresses than leaded components.  
Excess solder fillet height can multiply these stresses and cause chip cracking.  
When designing substrates, take land patterns and dimensions into consideration to eliminate the possibility  
of excess solder fillet height.  
1-2. There is a possibility of chip cracking caused by PCB expansion/contraction with heat, because stress  
on a chip is different depending on PCB material and structure.When the thermal expansion coefficient  
greatly differs between the board used for mounting and the chip,it will cause cracking of the chip due to  
the thermal expansion and contraction. When capacitors are mounted on a fluorine resin printed circuit  
board or on a single-layered glass epoxy board, it may also cause cracking of the chip for the same reason.  
Pattern Forms  
Prohibited  
Correct  
Chassis  
Solder Resist  
Solder (ground)  
Placing Close to Chassis  
Electrode Pattern  
Lead Wire  
in section  
in section  
in section  
in section  
Solder Resist  
Placing of Chip  
Components  
and Leaded  
Components  
in section  
Soldering Iron  
Lead Wire  
Placing of Leaded  
Components  
after Chip Component  
Solder Resist  
in section  
Solder Resist  
Lateral Mounting  
JEMCGC-00326E  
22  
Notice  
2. Land Dimensions  
Chip Capacitor  
Please confirm the suitable land dimension by  
evaluating of the actual SET / PCB.  
Land  
b
a
Solder Resist  
Table 1 Flow Soldering Method  
ChipDimension  
(L/W)Code  
Series  
Chip(L×W)  
1.6×0.8  
a
b
c
GJ8  
GJ8  
GJ8  
18  
21  
31  
0.6 to 1.0  
1.0 to 1.2  
2.2 to 2.6  
0.8 to 0.9  
0.6 to 0.8  
0.8 to 1.1  
1.0 to 1.4  
2.0×1.25  
3.2×1.6  
0.9 to 1.0  
1.0 to 1.1  
Resistance to PCB bending stress may be improved by designing the “a” dimension with solder resist.ꢀꢀꢀ (in mm)  
Table 2 Reflow Soldering Method  
Chip(L×W)  
ChipDimension  
(L/W)Code  
Series  
GJ8  
(Dimensions  
Tolerance)  
1.6×0.8  
a
b
c
18  
0.7 to 0.9  
1.2  
0.7 to 0.8  
0.6  
0.8 to 1.0  
1.25  
(±0.15)  
2.0×1.25  
(±0.10)  
2.0×1.25  
(±0.20)  
GJ8  
21  
1.0 to 1.4  
0.6 to 0.8  
1.2 to 1.4  
3.2×1.6  
(±0.20)  
GJ8  
GJ8  
31  
32  
1.8 to 2.0  
2.0 to 2.4  
0.9 to 1.2  
1.0 to 1.2  
1.5 to 1.7  
1.8 to 2.3  
3.2×2.5  
(in mm)  
JEMCGC-00326E  
23  
Notice  
3. Board Design  
Relationship with amount of strain to the board thickness, length, width, etc.]  
3PL  
When designing the board, keep in mind that  
the amount of strain which occurs will increase  
depending on the sizeand material of the board.  
Relationshipbetweenloadandstrain  
ε=  
2Ewh2  
εStrain on center of board (μst)  
LDistance between supporting points (mm)  
P
Y
w
h
E
Y
P
Board width (mm)  
Board thickness (mm)  
Elastic modulus of board (N/m2=Pa)  
Deflection (mm)  
h
Load (N)  
w
L
When the load is constant, the following relationship can be established.  
· As the distance between the supporting points (L) increases,the amount of strain also increases.  
→Reduce the distance between the supporting points.  
2.Item to be confirmed for Flow sordering  
· As the elastic modulus (E) decreases, the amount of strain increases.  
→Increase the elastic modulus.  
If you want to temporarily attach the capacitor  
to the board using an adhesive agent before  
soldering the capacitor, first be sure that the  
conditions are appropriate for affixing the  
·
As the board width (w) decreases, the amount of strain increases.  
→Increase the width of the board.  
As the board thickness (h) decreases, the amount of strain increases.  
·
→Increase the thickness of the board.  
Since the board thickness is squared, the effect on the amount of strain becomes even greater.  
capacitor. If the dimensions of the land, the type of adhesive,the amount of coating, the contact surface area,  
the curing temperature, or other conditions are inappropriate, the characteristics of the capacitor may deteriorate.  
1. Selection of Adhesive  
1-1. Depending on the type of adhesive, there may be a decrease in insulation resistance. In addition, there is a chance  
that the capacitor might crack from contractile stress due to the difference in the contraction rate of the capacitor  
and the adhesive.  
1-2. If there is not enough adhesive, the contact surface area is too small, or the curing temperature or curing time  
are inadequate, the adhesive strength will be insufficient and the capacitor may loosen or become disconnected  
during transportation or soldering. If there is too much adhesive, for example if it overflows onto the land, the result  
could be soldering defects, loss of electrical connection, insufficient curing, or slippage after the capacitor is mounted.  
Furthermore, if the curing temperature is too high or the curing time is too long, not only will the adhesive strength  
be reduced, but solderability may also suffer due to the effects of oxidation on the terminations (outer electrodes)  
of the capacitor and the land surface on the board.  
(1) Selection of Adhesive  
Epoxy resins are a typical class of adhesive. To select the proper adhesive, consider the following points.  
1) There must be enough adhesive strength to prevent the component from loosening or slipping during the  
ꢀꢀꢀꢀmounting process.  
2) The adhesive strength must not decrease when exposed to moisture during soldering.  
3) The adhesive must have good coatability and shape retention properties.  
4) The adhesive must have a long pot life.  
5) The curing time must be short.  
6) The adhesive must not be corrosive to the exterior of the capacitor or the board.  
7) The adhesive must have good insulation properties.  
8) The adhesive must not emit toxic gases or otherwise be harmful to health.  
9) The adhesive must be free of halogenated compounds.  
(2) Use the following illustration as a guide to the amount of adhesive to apply.  
ꢀꢀChipDimension (L/W)Code:18/21/31  
Adhesive  
Land  
Resist  
Resist  
Cross Sectional View  
Side View  
JEMCGC-00326E  
24  
Notice  
2.Flux  
2-1. An excessive amount of flux generates a large quantity of flux gas, which can cause a deterioration of solderability,  
so apply flux thinly and evenly throughout. (A foaming system is generally used for flow solderring.)  
2-2. Flux containing too high a percentage of halide may cause corrosion of the terminations unless there is  
sufficient cleaning. Use flux with a halide content of 0.1% max.  
2-3. Do not use strong acidic flux.  
2-4. Do not use water-soluble flux.*  
(*Water-soluble flux can be defined as non-rosin type flux including wash-type flux and non-wash-type flux.)  
3.Leaching of the terminations  
Set temperature and time to ensure that leaching of the  
terminations does not exceed 25% of the chip end  
area as a single chip (full length of the edge A-B-C-D  
As a Single Chip]  
A
B
shown at right) and 25% of the length A-B shown as  
mounted on substrate.  
D
Termination  
C
As Mounted on Substrate]  
B
A
3.Reflow soldering  
The halogen system substance and organic acid are included in solder paste, and a chip corrodes  
by this kind of solder paste. Do not use strong acid flux. Do not use water-soluble flux.*  
(*Water-soluble flux can be defined as non-rosin type flux including wash-type flux and non-wash-type flux.)  
4.Washing  
1. Please evaluate the capacitor using actual cleaning equipment and conditions to confirm the quality,  
and select the solvent for cleaning.  
2. Unsuitable cleaning solvent may leave residual flux or other foreign substances, causing deterioration of  
electrical characteristics and the reliability of the capacitors.  
3. Select the proper cleaning conditions.  
3-1. Improper cleaning conditions (excessive or insufficient) may result in the deterioration of the performance  
of the capacitors.  
5.Coating  
1. A crack may be caused in the capacitor due to the stress of the thermal contraction of the resin during curing process.  
The stress is affected by the amount of resin and curing contraction. Select a resin with low curing contraction.  
The difference in the thermal expansion coefficient between a coating resin or a molding resin and the capacitor  
may cause the destruction and deterioration of the capacitor such as a crack or peeling, and lead to the deterioration  
of insulation resistance or dielectric breakdown.  
Select a resin for which the thermal expansion coefficient is as close to that of the capacitor as possible.  
A silicone resin can be used as an under-coating to buffer against the stress.  
2. Select a resin that is less hygroscopic.  
Using hygroscopic resins under high humidity conditions may cause the deterioration of the insulation resistance  
of a capacitor. An epoxy resin can be used as a less hygroscopic resin.  
3The halogen system substance and organic acid are included in coating material, and a chip corrodes  
ꢀꢀby the kind of Coating material. Do not use strong acid type.  
JEMCGC-00326E  
25  
Notice  
Others  
1.Transportation  
1. The performance of a capacitor may be affected by the conditions during transportation.  
1-1. The capacitors shall be protected against excessive temperature, humidity and mechanical force during transportation.  
(1) Climatic condition  
ꢀ・ low air temperature : -40℃  
change of temperature air/air : -25/+25℃  
low air pressure : 30 kPa  
change of air pressure : 6 kPa/min.  
(2) Mechanical condition  
Transportation shall be done in such a way that the boxes are not deformed and forces are not directly passed  
on to the inner packaging.  
1-2. Do not apply excessive vibration, shock, or pressure to the capacitor.  
(1) When excessive mechanical shock or pressure is applied to a capacitor, chipping or cracking may occur  
in the ceramic body of the capacitor.  
(2) When the sharp edge of an air driver, a soldering iron, tweezers, a chassis, etc. impacts strongly on the surface  
of the capacitor, the capacitor may crack and short-circuit.  
1-3. Do not use a capacitor to which excessive shock was applied by dropping etc.  
A capacitor dropped accidentally during processing may be damaged.  
2.Characteristics Evaluation in the Actual System  
1. Evaluate the capacitor in the actual system,to confirm that there is no problem with the performance and specification  
values in a finished product before using.  
2. Since a voltage dependency and temperature dependency exists in the capacitance of high dielectric type ceramic  
capacitors, the capacitance may change depending on the operating conditions in the actual system.  
Therefore,be sure to evaluate the various characteristics, such as the leakage current and noise absorptivity,  
which will affect the capacitance value of the capacitor.  
3. In addition,voltages exceeding the predetermined surge may be applied to the capacitor by the inductance in  
the actual system. Evaluate the surge resistance in the actual system as required.  
JEMCGC-00326E  
26  
NOTE  
!
1.Please make sure that your product has been evaluated in view of your specifications with our  
product being mounted to your product.  
2.Your are requested not to use our product deviating from this product specification.  
3.We consider it not appropriate to include any terms and conditions with regard to the business  
transaction in the product specifications, drawings or other technical documents. Therefore,  
if your technical documents as above include such terms and conditions such as warranty clause,  
product liability clause, or intellectual property infringement liability clause, they will be deemed to  
be invalid.  
JEMCGC-00326E  
27  

GJ831CR71H475MA12# 相关器件

型号 制造商 描述 价格 文档
GJ832ER7YA106KA12 MURATA capacitor data sheet 获取价格
GJ832ER7YA106KA12# MURATA 民用设备,工业设备,移动设备,植入式以外的医疗器械设备 [GHTF A/B/C],汽车[信息娱乐 / 舒适设备] 获取价格
GJ8550 GTM PNP EPITAXIAL TRANSISTOR 获取价格
GJ85L02 GTM N-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格
GJ85T03 GTM N-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格
GJ882 GTM NPN EPITAXIAL PLANAR TRANSISTOR 获取价格
GJ88L02 GTM N-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格
GJ88LS02 GTM N-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格
GJ90T03 GTM N-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格
GJ9435 GTM P-CHANNEL ENHANCEMENT MODE POWER MOSFET 获取价格

GJ831CR71H475MA12# 相关文章

  • HARTING(浩亭)圆形连接器产品选型手册
    2024-10-31
    6
  • HYCON(宏康科技)产品选型手册
    2024-10-31
    6
  • GREEGOO整流二极管和晶闸管产品选型手册
    2024-10-31
    7
  • 西门子豪掷106亿美元,战略收购工程软件巨头Altair
    2024-10-31
    8