LQM18PN2R2NC0L [MURATA]
General Purpose Inductor,;型号: | LQM18PN2R2NC0L |
厂家: | muRata |
描述: | General Purpose Inductor, 测试 射频感应器 电感器 |
文件: | 总9页 (文件大小:158K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Reference Only
Spec No. JELF243B-0030F-01
P.1/10
CHIP COIL (CHIP INDUCTORS) LQM18PN□□□□C0L REFERENCE SPECIFICATION
1. Scope
This reference specification applies to LQM18PN_C0 series, Chip coil (Chip Inductors).
2. Part Numbering
(ex)
LQ
Product ID Structure Dimension Applications Category Inductance Tolerance Dimension Other
(L×W) and (T)
Characteristics
M
18
P
N
1R8
N
C
0
L
Packaging
L:Taping
*B:BULK
*B:Bulk packing also available
3. Rating
・Operating Temperature Range
・Storage Temperature Range
– 55°C to + 125°C
– 55°C to + 125°C
Self
Inductance
DC
Resistance
( Ω)
Rated
Current
(mA)
Customer
Part Number
MURATA
Part Number
Resonant
Frequency
(MHz min.)
(μH)
Tolerance
LQM18PNR47NC0L 0.47
0.15±25%
0.20±25%
0.22±25%
850
750
720
LQM18PN1R0NC0L
LQM18PN1R5NC0L
LQM18PN1R8NC0L
LQM18PN2R2NC0L
1.0
1.5
1.8
2.2
±30%
50
0.24±25%
700
4. Testing Conditions
《Unless otherwise specified》
Temperature : Ordinary Temperature / 15°C to 35°C
《In case of doubt》
Temperature : 20°C ± 2°C
Humidity : 60%(RH) to 70%(RH)
Humidity
: Ordinary Humidity
/ 25%(RH) to 85%(RH)
Atmospheric Pressure : 86kPa to 106kPa
5. Appearance and Dimensions
Electrode
Ferrite
■Unit Mass (Typical value)
0.4±0.2
0.003g
0.5±0.05
1.6±0.15
0.8±0.15
(in mm)
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.2/10
6. Electrical Performance
No.
Item
Specification
Inductance shall meet item 3.
Test Method
Measuring Equipment:
KEYSIGHT 4294A or equivalent (1mA)
Measuring Frequency: 1MHz
6.1 Inductance
6.2 DC Resistance DC Resistance shall meet item 3.
Measuring Equipment: Digital multi meter
Digital multi meter
(TR6846 or equivalent)
a
terminal1
terminal2
SW
b
DC resistance shall be measured after
putting chip coil between the terminal 2
under the condition of opening between
a and b.
Every measurement the terminal 1 shall
be shorted between a and b when
changing chip coil.
6.3 Self Resonant
Frequency
S.R.F shall meet item 3.
Measuring Equipment:
KEYSIGHT 4294A or equivalent
(S.R.F)
6.4 Rated Current
Self temperature rise shall be The rated current is applied.
limited to 40°C max.
7. Mechanical Performance
No. Item
Specification
Chip coil shall not be damaged after
tested as follows.
Test Method
Applied Direction
Chip Coil
7.1 Shear Test
F
Substrate
Force: 10N
Hold Duration: 5s±1s
Applied Direction: Parallel to PCB
Appearance: No damage
Substrate: Glass-epoxy substrate
7.2 Bending Test
(100mm×40mm×1.0mm)
Solder: Reflow
Pressure jig
F
R230
Deflection
(in mm)
Product
45
45
Speed of Applying Force: 0.5mm / s
Deflection: 2mm
Hold Duration: 30 s
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.3/10
No.
Item
Specification
Appearance: No damage
Test Method
Oscillation Frequency:
7.3 Vibration
10Hz to 2000Hz to 10Hz for 20 min
Total amplitude 3.0 mm or Acceleration
amplitude 245m/s2 whichever is smaller.
Testing Time:
A period of 4h in each of 3 mutually
perpendicular directions.
7.4 Drop
It shall be dropped on concrete or steel
board.
Method : free fall
Height : 1m
Total of 10 cycles
7.5 Solderability
The wetting area of the electrode
shall be at least 90% covered with
new solder coating.
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 240°C±5°C
Immersion Time: 3s±1s
7.6 Resistance to
Soldering Heat
Appearance: No damage
Inductance Change: within ±30%
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 270°C±5°C
Immersion Time: 10s±1s
Then measured after exposure in the room
condition for 24h±2h.
8. Environmental Performance
It shall be soldered on the substrate.
No.
Item
Specification
Test Method
Temperature: 125°C±2°C
Time:1000h (+48h, -0h)
Then measured after exposure in the room
condition for 24h±2h.
8.1 Heat Resistance
8.2 Cold Resistance
8.3 Humidity
Appearance: No damage
Inductance Change: within ±20%
Temperature: -55°C±2°C
Time: 1000h (+48h, -0h)
Then measured after exposure in the room
condition for 24h±2h.
Temperature: 70°C±2°C
Humidity: 90%(RH) to 95%(RH)
Time: 1000h (+48h, -0h)
Then measured after exposure in the room
condition for 24h±2h.
8.4 Temperature
Cycle
Appearance: No damage
Inductance Change: within ±30%
1 cycle:
1 step: -55°C±2°C / 30 min±3 min
2 step: Ordinary temp. / 10 min to 15 min
3 step: +125°C±2°C / 30 min to 3 min
4 step: Ordinary temp. / 10 min to15 min
Total of 100cycles
Then measured after exposure in the room
condition for 24h±2h.
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.4/10
9. Specification of Packaging
9.1 Appearance and Dimensions of plastic tape (8mm-wide)
2.0±0.05
0.60±0.05
0.1
0
4.0±0.1
4.0±0.1
φ1.5±
0.30±0.05
1.75±0.1
(in mm)
Direction of feed
1.0±0.1
・Dimension of the Cavity is measured at the bottom side.
9.2 Specification of Taping
(1) Packing quantity (standard quantity)
4,000 pcs / reel
(2) Packing Method
Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape.
(3) Sprocket hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
Plastic tape and Cover tape has no spliced point.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The Specified quantity per reel is kept.
9.3 Pull Strength
Plastic tape
Cover tape
10N min.
5N min.
9.4 Peeling off force of cover tape
165 to 180 degree
Speed of Peeling off
Peeling off force
300mm / min
F
Cover tape
Plastic tape
Plastic tape: 0.1N to 0.7N
(minimum value is typical)
9.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows.
Trailer
160 min.
Leader
2.0±0.5
190 min.
210 min.
Label
Empty tape Cover tape
13.0±0.2
60± 10
9± 10
13±1.4
21.0±0.8
Direction of feed
180±03
(in mm)
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.5/10
9.6 Marking for reel
Customer part number, MURATA part number, Inspection number (1), RoHS Marking (2),
Quantity etc ・・・
1) <Expression of Inspection No.>
□□ OOOO
(1)
(2)
(3)
(1) Factory Code
(2) Date
First digit
: Year / Last digit of year
Second digit
Third, Fourth digit : Day
: Month / Jan. to Sep. 1 to 9, Oct. to Dec. O, N, D
(3) Serial No.
2) <Expression of RoHS Marking >
ROHS – Y (△)
(1) (2)
(1) RoHS regulation conformity parts.
(2) MURATA classification number
9.7 Marking for Outside package (corrugated paper box)
Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS Marking (2), Quantity, etc ・・・
9.8 Specification of Outer Case
Outer Case Dimensions
Standard Reel Quantity
in Outer Case (Reel)
(mm)
D
Label
W
H
H
186
186
93
5
D
Above Outer Case size is typical. It depends on a quantity of an order
W
10. ! Caution
Limitation of Applications
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party's life,
body or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3) Undersea equipment
(6) Transportation equipment (vehicles, trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(4) Power plant control equipment (9) Data-processing equipment
(5) Medical equipment
(10) Applications of similar complexity and /or reliability
requirements to the applications listed in the above
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.6/10
11. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
11.1 Land pattern designing
Chip Coil
Land
Solder Resist
c
Soldering
Flow
Reflow
a
b
c
2.2 to 2.6
1.8 to 2.0
(in mm)
0.7
0.7
a
b
11.2 Flux, Solder
・Use rosin-based flux.
Don’t use highly acidic flux with halide content exceeding 0.2(wt) % (chlorine conversion value).
Don’t use water-soluble flux.
・Use Sn-3.0Ag-0.5Cu solder.
・Standard thickness of solder paste: 100μm to 150μm.
11.3 Flow soldering / Reflow soldering conditions
・Pre-heating should be in such a way that the temperature difference between solder and product
surface is limited to 150°C max. Cooling into solvent after soldering also should be in such a way that
the temperature difference is limited to 100°C max.
Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of products
quality.
・Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and/or resulting in the
deterioration of product quality.
Soldering profile
(1) Flow soldering profile
Temp.
(℃)
265℃±3℃
250℃
Limit Profile
150
Heating Time
Standard Profile
60s min.
Time.(s)
Standard Profile
150℃, 60s min.
Limit Profile
Pre-heating
Heating
250℃, 4s~6s
265℃±3℃, 5s
Cycle of flow
2 times
2 times
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
(2) Reflow soldering profile
P.7/10
Temp.
(℃)
260℃
245℃±3℃
230℃
220℃
Limit Profile
180
150
Standard Profile
30s~60s
60s max.
90s±30s
Time.(s)
Standard Profile
Limit Profile
Pre-heating
150°C~180°C, 90s±30s
Heating
Peak temperature
Cycle of reflow
above 220°C, 30s~60s
245°C±3°C
above 230°C, 60s max.
260°C,10s
2 times
2 times
11.4 Reworking with soldering iron
The following conditions must be strictly followed when using a soldering iron.
Pre-heating
150°C,1 min
350°C max.
80W max.
φ3mm max.
3(+1, -0)s
2 times
Tip temperature
Soldering iron output
Tip diameter
Soldering time
Time
Note : Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on
the products due to the thermal shock.
11.5 Solder Volume
・Solder shall be used not to be exceeded the upper limits as shown below.
・Accordingly increasing the solder volume, the mechanical stress to Chip is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
Upper Limit
Recommendable
1/3T≦t≦T
t
T: thickness of electrode
11.6 Product’s location
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board.
[Products direction]
a
b
Products shall be located in the sideways
direction (Length: a‹b) to the mechanical
stress.
Poor example
〈
〉
Good example
〈
〉
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.8/10
(2)Components location on P.C.B. separation.
It is effective to implement the following measures, to reduce stress in separating the board.
It is best to implement all of the following three measures; however, implement as many measures
as possible to reduce stress.
Contents of Measures
Stress Level
(1) Turn the mounting direction of the component parallel to the board separation surface.
(2) Add slits in the board separation part.
A
>
D *1
B
A
>
>
(3) Keep the mounting position of the component away from the board separation surface.
A
C
C
Perforation
B
D
A
Slit
*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs
during the tightening of the screw. Mount the component in a position as far away from the screw holes
as possible.
Recommended
Screw Hole
11.7 Cleaning Conditions
Products shall be cleaned on the following conditions.
(1) Cleaning temperature shall be limited to 60°C max. (40°C max for IPA.)
(2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance
phenomenon at the mounted products and P.C.B.
Power : 20 W / l max.
(3) Cleaner
Frequency : 28kHz to 40kHz
Time : 5 min max.
1. Alcohol type cleaner
Isopropyl alcohol (IPA)
2. Aqueous agent
PINE ALPHA ST-100S
(4) There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent,
products shall be dried completely after rinse with de-ionized water in order to remove the cleaner.
(5) Other cleaning Please contact us.
11.8 Resin coating
The inductance value may change and/or it may affect on the product's performance due to high
cure-stress of resin to be used for coating/molding products. So please pay your careful attention when
you select resin.
In prior to use, please make the reliability evaluation with the product mounted in your application set.
MURATA MFG.CO., LTD
Reference Only
Spec No. JELF243B-0030F-01
P.9/10
11.9 Caution for use
There is possibility that the inductance value change due to magnetism. Don‘t use a magnet or a pair of
tweezers with magnetism when chip coil are handled. (The tip of the tweezers should be molded with resin or
pottery.)
11.10 Magnetic Saturation
When the excessive current over rated current is applied, the inductance value may change due to
magnetism.
11.11 Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or
twisting to the substrate when cropping the substrate, inserting and removing a connector from the
substrate or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
11.12 Storage and Handing Requirements
(1) Storage period
Use the products within 6 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage conditions
・Products should be stored in the warehouse on the following conditions.
Temperature : -10°C to 40°C
Humidity
: 15% to 85% relative humidity No rapid change on temperature and humidity
Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization
of electrode, resulting in poor solderability.
・Products should be stored on the palette for the prevention of the influence from humidity, dust and so
on.
・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
・Products should be stored under the airtight packaged condition.
(3) Handling Condition
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical
shock.
12.! Note
(1) Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
(2) You are requested not to use our product deviating from the reference specifications.
(3) The contents of this reference specification are subject to change without advance notice.
Please approve our product specifications or transact the approval sheet for product specifications
before ordering.
MURATA MFG.CO., LTD
相关型号:
LQM18PN3R3MFRL
General Purpose Inductor, 3.3uH, 20%, 1 Element, Ferrite-Core, SMD, 0603, CHIP, 0603
MURATA
©2020 ICPDF网 联系我们和版权申明