NMG0524SC [MURATA]
民用设备,工业设备;型号: | NMG0524SC |
厂家: | muRata |
描述: | 民用设备,工业设备 电源电路 |
文件: | 总4页 (文件大小:142K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NMG Series
Isolated 2W Single Output DC/DC Converters
SELECTION GUIDE
Order Code
V
5
V
5
mA
400
222
167
133
400
222
167
133
mA
470
455
450
450
200
190
190
185
%
mVp-p
28
%
81
84
85
85
81
83
85
85
%
83
pF
33
40
40
40
40
61
74
68
kHrs
3956
3682
3299
2833
2519
2405
2235
2011
NMG0505SC
NMG0509SC
NMG0512SC
NMG0515SC
NMG1205SC
NMG1209SC
NMG1212SC
NMG1215SC
5.7
4.2
3.8
3.4
4.2
2.6
2.4
2.0
7.3
5.9
5.1
4.5
4.9
3.1
2.9
2.4
35
25
25
25
35
25
25
25
5
9
20
18
16
22
16
13
12
86.5
87.5
87.5
83.5
87
5
12
15
5
5
FEATURES
ꢀRoHS compliant
12
12
12
12
9
ꢀEfficiency from 81%
12
15
88
88
ꢀWide temperature performance at full
2 Watt load, –40°C to 85°C
When operated with additional external load capacitance the rise time of the input voltage will determine the maximum external
capacitance value for guaranteed start up. The slower the rise time of the input voltage the greater the maximum value of the
additional external capacitance for reliable start up.
ꢀUL 94V-0 package material
ꢀIndustry standard pinout
ꢀ1kVDC isolation
INPUT CHARACTERISTICS
Parameter
Conditions
Min.
4.5
Typ.
5
Max.
5.5
Units
V
Continuous operation, 5V input types
Continuous operation, 12V input types
Voltage range
ꢀ5V & 12V input
10.8
12
13.2
15
Reflected ripple current
7.5
mA p-p
ꢀ5V, 9V, 12V, & 15V output
ꢀInternal SMD construction
ABSOLUTE MAXIMUM RATINGS
Lead temperature 1.5mm from case for 10 seconds
Internal power dissipation
300°C
ꢀFully encapsulated with toroidal
magnetics
550mW
7V
Input voltage VIN, NMG05 types
ꢀNo external components required
ꢀMTTF up to 3.9 million hours
Input voltage VIN, NMG12 types
15V
OUTPUT CHARACTERISTICS
ꢀPin compatible with NMR series
ꢀNo electrolytic or tantalum capacitors
Parameter
Conditions
Min.
Typ.
Max.
2
Units
W
Rated Power
TA=-40°C to 85°C
Voltage Set Point Accuracy See tolerance envelope
Line regulation High VIN to low VIN
1.05
Typ.
1.2
%/%
PRODUCT OVERVIEW
The NMG series of DC/DC Converters is
ISOLATION CHARACTERISTICS
Parameter
Conditions
Min.
1000
10
Max.
Units
VDC
GΩ
particularly suited to isolating and/or converting
DC power rails. The galvanic isolation allows the
device to be configured to provide an isolated
negative rail in systems where only positive rails
exist. The wide temperature range guarantees
startup from –40°C and full 2 watt output at 85°C.
Pin compatibility with the NMR series ensures
ease of upgradeability.
Isolation test voltage
Resistance
Flash tested for 1 second
Viso= 1000VDC
GENERAL CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
60
Max.
Units
kHz
Switching frequency
TEMPERATURE CHARACTERISTICS
Parameter
Specification
Storage
Conditions
All output types
Min.
-40
Typ.
Max.
85
Units
°C
-50
125
30
NMG0505
Case Temperature above
ambient
NMG1205
25
All other output types
Free air convection
20
Cooling
1. See Ripple & Noise characterisation method.
2. Calculated using MIL-HDBK-217F FN2 with nominal input voltage at full load.
For full details go to
www.murata-ps.com/rohs
All specifications typical at T =25°C, nominal input voltage and rated output current unless otherwise specified.
A
www.murata-ps.com
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
KDC_NMGC.A03 Page 1 of 4
NMG Series
Isolated 2W Single Output DC/DC Converters
TEMPERATURE DERATING GRAPH
TOLERANCE ENVELOPE
5%
3
85°C
2%
0%
2
VNOM
1
0
Safe Operating Area
-4%
100
75
Output Load Current (%)
10 25
50
-40
100
Ambient Temperature (°C)
150
0
50
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMG series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 minute.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specific agency approvals, such as the NMG series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMG series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
300°C for 10 seconds. The pin termination finish is Tin Plate, Hot Dipped over Matte Tin with Nickel
Preplate. This series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
www.murata-ps.com
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
KDC_NMGC.A03 Page 2 of 4
NMG Series
Isolated 2W Single Output DC/DC Converters
RIPPLE & NOISE CHARACTERISATION METHOD
All measurement to be taken with the following components connected to the UUT as detailed below.
50 Ohm coax cable, solder connections one end, BNC plug at the other end.
C1
C2
– 1μF X7R multilayer ceramic capacitor rated at minimum 3 x the output voltage of the UUT
– 10μF tantalum capacitor rated at minimum 1.5 x the output voltage of the UUT with ESR of less
than 100 milliohms at 100 kHz e.g. AVX TPS series.
C3
R1
R2
T1
– 100nF multilayer ceramic capacitor, general purpose
– 450 Ohm resistor, carbon film, 1%
– 50 Ohm BNC termination
– 3T of the coax cable through a ferrite toroid eg Ferroxcube TN32/19/13-3E25
RLOAD – Resistive load at the UUT maximum rating. Connections via twisted wires.
Differential Mode Noise Test Schematic
DC/DC Converter
OSCILLOSCOPE
R2
C1 C2 C3
R1
T1
Y INPUT
+
+
Input
Output
SUPPLY
-
-
R LOAD
EFFICIENCY VS LOAD
NMG 5V Input Voltage
NMG 12V Input Voltage
90
90
80
70
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
15V
12V
9V
15V
12V
9V
5V
5V
0
10
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
Load (%)
60
70
80
90
100
Load (%)
www.murata-ps.com
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
KDC_NMGC.A03 Page 3 of 4
NMG Series
Isolated 2W Single Output DC/DC Converters
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
PIN CONNECTIONS - 4 PIN SIP
0.77
(19.50)
Pin
1
Function
+VIN
2
-VIN
4
-VOUT
0.295
(7.50)
6
+VOUT
TUBE OUTLINE DIMENSIONS
ꢀꢁꢋꢍꢍꢄꢅꢃꢁꢋꢀꢈꢄ
0.394
(10.00)
NMG0505SC
0.022 (0.55)
0.0178 (0.45)
XYYWWi
6
1
2
4
0.181 (4.60)
0.141 (3.60)
0.1 (2.54)
0.22 (0.55)
0.0178 (0.45)
0.079
(2.00)
0.0118 (0.30)
0.0079 (0.20)
0.05
(1.25)
0.5 (12.70)
ꢀꢁꢊꢄꢅꢌꢁꢀꢀꢈꢄ
All dimensions in inches 0.01 (mm 0.25mm). All pins on a 0.1 (2.54)
pitch and within 0.01 (0.25) of true position.
Unless otherwise stated all dimensions in inches (mm) 0.5mm.
Tube length : 20.47 (520mm 2mm).
Tube Quantity : 25
Weight: 2.8g
RECOMMENDED FOOTPRINT DETAILS
0.045 (1.15)
0.039 (1.00)
4 HOLES
Ø
0.00394 (0.1)
0.1 (2.54)
0.1 (2.54)
Unless otherwise stated all dimensions in inches (mm) 0.5mm.
USA:
Canada: Toronto, Tel: (866) 740 1232, email: toronto@murata-ps.com
UK: Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com
Tucson (Az), Tel: (800) 547 2537, email: sales@murata-ps.com
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com
Germany: München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com
Japan: Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com
Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com
Website: www.murata-ps.jp
www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
China:
Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com
Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com
notice.
© 2008 Murata Power Solutions, Inc.
www.murata-ps.com
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
KDC_NMGC.A03 Page 4 of 4
相关型号:
©2020 ICPDF网 联系我们和版权申明