PKGS-00LDP1-R [MURATA]
Analog Circuit,;
| 型号： | PKGS-00LDP1-R |
| 厂家： | 
muRata |
| 描述： | Analog Circuit, |
| 文件： | 总15页 (文件大小：144K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Reference only
P.1 /15
Product Specification for Reference Only
Issued Date:
Rev. :
Jun. 05, 2013
2
Part Description:
S H O C K S E N S O R
P K G S - 0 0 L D P 1 - R
MURATA Part No.:
The product specification in this sheet is for reference only.
The contents of this specification are subject to change.
You are requested to receive the latest specification and to return one
copy of the specification to us with your receipt signature before going
into mass production.
Product engineering section
Sensor Products Department
Sensor Products Division
Murata MFG. Co.,Ltd.
Approved by
Issued by
Issued Date
Drawing No.
H. Kita
T. Kawamoto
Nov. 1, 2010
Reference only
Reference only
P.2 /15
SPECIFICATION for TRANSDUCER
Part Number: PKGS-00LDP1-R
1. Scope
This product specification is applied to surface mountable acceleration sensors used for hard
disk drive in a personal computer. Please contact us before using any of the products in the
applications not described above.
2. Part Number
2-1 Murata Part Number
:PKGS-00LDP1-R
:
2-2 Customer Part Number
2-3 Customer Drawing Number :
3. Outline Drawing and Dimensions
3-1 Appearance
3-2 Dimensions
3-3 Construction
: As per paragraph 10.Appearance criteria.
: See Figure 2.
: A piezo ceramic element is stuck between two ceramic substrate.
4. Characteristics
(∗ Temperature 25±3°C, unless otherwise noted)
Parameter
Test Condition
Min.
Typ.
Max.
Units
Note
1,2,5
4-1 Electric Charge
Sensitivity
1kHz, 98.1m/s2(10G) applied
in the direction of D axis at Fig.1
-15%
85.7
{0.840}
+15%
fC/(m/s2)
{pC/G}
4-2 Insulation
Resistance
10V DC, after 1 min.
500
10000
MΩ
4-3 Non-Linearity
% of the Full-Scale output at 490
1%
5%
m/s2(50G). Range : ±50G
4-4 Resonance
Frequency
17
-3
20
0
kHz
3
4-5 Inclined Angle of
Sensitivity Axis
Maximum deviation
from initial value at +25°C.
Maximum deviation
from initial value at
+25°C
1Vrms,1kHz
1kHz, 98.1m/s2(10G) applied in the
direction of D axis at Fig.1
+3
Degree
4-6 Electric Charge
Sensitivity
Temperature Drift
4-7 Capacitance
Ref. <reference Only>
Voltage Sensitivity
Ta:70°C
Ta:0°C
0%
+4%
+10%
-5%
-2.5%
0%
-30%
770
+30%
pF
{1.10}
{mV/G}
1,2,4
Note:
1. As measured with an applied acceleration in the direction of D at figure 1. In this case, positive
voltage and electrical charge are generated at electrode B.
2. 1[G] = 9.80665 [m/s2]
3. Resonance frequency of inner bimorph element.
4. Input impedance of measurement circuit is 10 MΩ(Zi), and amplified gain is 0 dB.
5. f (femto)= 10-15
MURATA MANUFACTURING CO., LTD
Reference only
P.3 /15
Z
Y
D
0±1°
Electrode A
X
Polarity marking
Electrode B
Figure 1.
Axis D : This axis is an acceleration applied direction, when electric charge sensitivity is checked.
5. Standard land pattern
Land pattern
2.0
3.4
2.0
Unit : mm
6. Absolute Rating
Apply voltage between electrode A and B : 10 Vp-p within 60 sec. max.
Storage temperature range
Operating temperature range
: -40 to 85 °C
: -40 to 85 °C
MURATA MANUFACTURING CO., LTD
Reference only
P.4 /15
7. Physical Characteristics
Test Item
Condition of Test
Performance Requirements
7-1 Mechanical
Shock
The transducer shall be measured after being No visible damage and the
applied three impacts in plus and minus measured values shall meet
directions of three mutually perpendicular Table 2
planes.
The shock is specified as 14700m/s2(1500G)
half sine pulse of 0.5 ms duration.
7-2 Vibration
The transducer shall be measured after being
applied vibration of amplitude of 1.5 mm with 10
to 55 Hz band of vibration frequency to each of 3
perpendicular directions for 2 hours.
( 5 minutes × 24 cycles )
7-3 Bend Strength The transducer is soldered onto the center of No visible damage and the
PCB PCB (1.6 mm thickness) which is laid on the 2 measured values shall meet
small supporters spaced 90 mm.
Table 3
PCB is deflected to 1 mm below from horizontal
level by the pressing force with 20 × 10. R10
stick. The force is supplied for 1 second, 5 times
repeatably.
Stick
Load
20 10
PCB
Deflection
R10
Part
45
±1 Off-Center
45
φ 5 Supporter
Unit: mm
7-4 Resistance to The transducer shall be mounted on PCB, then No visible damage and the
Reflow
measured after being applied following reflow measured values shall meet
Soldering
conditions.
Table 2
<Test flow>
Pre-heating :
60 to 150 sec. at 150 to 180 °C
Heating :
Within 60 sec. at 200 °C (or more)
Within 30 sec. at 250 °C (or more)
Peak Temperature:
Within 10 sec. at 260 °C
Shock sensor should be tested 2 times of this
test flow.
PCB size : 115 × 80 × 0.8 mm
After being placed at ambient conditions for 8
hours, the transducer shall be measured.
7-5 Solderability
7-6 Washability
End terminals are immersed in rosin for
5 seconds then immersed in soldering bath of be wet with solder.
+230±5°C for 3±0.5 seconds.
75% min. end terminals shall
See Table 1
No visible damage and the
measured values shall meet
Table 2
MURATA MANUFACTURING CO., LTD
Reference only
P.5 /15
Table 1 Wash
Cleaning
Alcohol
Water
Cleaning Water
Solution
Silicon
(Techno care FRW)
Solvent (Iso-propanol) (Tap water,
Demineralized
water)
(Cleanthrough
750H, Pine alpha
100S )
Item
Temperature
Difference: ΔT *1
[ΔT = Component
- Solvent]
ΔT<100°C
Condition
(1) Ultrasonic
Wash
1 minute max. in above solvent at 60°C max.
( Frequency : 28 kHz, Output : 20 W/L )
(2) Immersion
Wash
5 minutes max. in above solvent at 60°C max.
(3) Shower or
Rinse Wash
(4) Drying
5 minutes max. in above solvent at 60°C max.
1 to 5 minutes. by air blow at 80°C max.
*1 ex. In case the component at 90°C immerses into cleaning solvent at 60°C,
then ΔT = 30°C.
Note(Wash)
1.Please insure the component is thoroughly evaluated in your application circuit.
2.The component may be damaged if it is washed with alkali cleaning solvent.
3.Flux should be washed out before use.
MURATA MANUFACTURING CO., LTD
Reference only
P.6 /15
8. Environmental Characteristics
Test Item
Performance Requirements
Condition of Test
8-1 High
After being placed in a thermal chamber with at The measured values shall
Temperature +85±2°C for 1000 hours and then being placed at meet Table 2
ambient conditions for 8 hours, the transducer shall be
measured.
8-2 Low
After being placed in a thermal chamber with at The measured values shall
Temperature -40±2°C for 1000 hours and then being placed at meet Table 2
ambient conditions for 8 hours, the transducer shall be
measured.
8-3 Humidity
After being placed in a humidity chamber with
90 to 95% R.H. at +60±2°C for 500 hours
and the being placed at ambient conditions for
8 hours, the transducer shall be measured.
The measured values shall
meet Table 2
8-4 Heat Shock
After being kept at room temperature, the transducer The measured values shall
shall be placed in a thermal chamber at temperature of meet Table 2
-40°C.
After 30 minutes at this temperature, the transducer
shall be immediately placed in
a
chamber at
temperature of +85°C.
After 30 minutes at this temperature, the transducer
shall be returned to -40°C again.
After 10 of the above cycles, the transducer shall be
returned to ambient conditions where it shall remain for
8 hours prior to being measured.
Table 2
Electric Charge Sensitivity
±10% ( from initial value )
±10% ( from initial value )
Table 3
Capacitance
MURATA MANUFACTURING CO., LTD
Reference only
P.7 /15
9. Dimensions and Indication
Polarity marking
6.4 ±0.2
1.5 ±0.3
1.2 +0.1/-0.2
1.5 ±0.3
Indication: Indication may lap
over on the electrodes.
Top
Bottom
Electrode A
Electrode B
Unit: mm
1.5 ±0.3
1.5 ±0.3
Figure 2. Dimensions
Indication contents
Part number code⋅⋅⋅⋅⋅⋅⋅⋅ A
M
Manufacturing company mark⋅⋅⋅⋅⋅⋅⋅⋅ C
Monthly code⋅⋅⋅⋅⋅⋅⋅⋅Monthly code based on EIAJ-0901
Part number code
Dot
Monthly code
Manufacturing
company mark
MURATA MANUFACTURING CO., LTD
Reference only
P.8 /15
10. Appearance criteria
10-1. Crack, Chip and Partial lack of electrode
B-part
(Along with short edge)
A-part
(Along with long edge)
Electrode
Electrode for
Polarity marking
c
d
a
b
Corner
(*1) Any chips which is covered by electrode are judged as good.
• If crack or chip exist at corners, apply the above B-part standard.
• In case crack or chip reaches internal cavity, it is judged as failure even if length [b], [d] and width
[a], [c] are met this specification.
• If there are two or more chips on B part, total length of [d] should be < 1.2mm
Criteria table for A part
Unit [mm]
0 < b < 0.4
0.4 < b
G
0 < a < 1.2
1.2 < a
G
G
NG
Criteria table for B part
Unit [mm]
0 < d < 0.4
0.4 < d < 1.2
1.2 < d
G
0 < c < 0.4
G
G
G
G
G
0.4 < c < 1.2
1.2 < c
NG
NG
NG
MURATA MANUFACTURING CO., LTD
Reference only
P.9 /15
10-2. Electrode peeling and delamination
• Apply A-part standard to top and bottom electrode including polarity marking.
• Apply B-part standard to two-end electrode.
A-part
(Top, bottom,
d
b
polarity marking)
c
a
B-part
(Two-end)
Criteria table for A part
Unit [mm]
1.0 < b
0 < b < 0.4
0.4 < b < 1.0
0 < a < 0.4
G
G
G
G
G
G
0.4 < a < 1.0
1.0 < a
NG
NG
NG
Criteria table for B part
Unit [mm]
0 < d < 0.4
0.4 < d
G
0 < c < 1.0
1.0 < c
G
G
NG
MURATA MANUFACTURING CO., LTD
Reference only
P.10 /15
10-3. Electrode protrusion and bridge
Top view
Electrode for
polarity marking
B-part
A-part
c
h
b
a
Side view
C-part
d
M
[A-part]
• If electrode protrusion reaches opposite electrode, it should be failure.
• The same criteria are applied on the bottom electrode.
Criteria table for A part
Unit [mm]
0 < b < 0.4
0.4 < b
G
0 < a < 1.2
1.2 < a
G
G
NG
[B-part]
Criteria table for B part
Unit [mm]
c < h
h < c
NG
G (*1)
(*1) In case electrode protrude reaches to polarity marking, it should be good.
[C-part]
Criteria table for C part
Unit [mm]
M+ 1.2 < d
NG
d < M+ 1.2
G
MURATA MANUFACTURING CO., LTD
Reference only
P.11 /15
10-4. Position of connection electrode
Top view
Connection electrode
a > 0
a
• It is judged as good regardless of the position of connection electrode
Unit [mm]
a > 0
G
MURATA MANUFACTURING CO., LTD
Reference only
P.12 /15
11. Taping Method
11-1 The tape for transducer shall be would clockwise. The feeding holes shall be to the right side
as the tape is pulled toward the user.
11-2 A reel shall contain 2,000 pcs of transducers and be clearly marked with part number,
quantity, inspection number.
4.0 ±0.1
+0.1
φ 1.5 -0.0
2.0 ±0.1
+0.3
4.0 ±0.1
196 to 686mN (20 to 70gf)
φ 1.5 -0.0
3.2 ±0.1
300mm/min.
Cover Tape
(3° )
10°
Unit: mm
Direction of Feed
Figure.3 Dimension of Plastic Tape
Trailer
110 to 190
100 Min. weld
Leader
Cover Tape
160 Min.
400 to 560
+0.5
2 –0.2
φ13 ±0.5
Unit : mm
+1.0
12.5 –0.0
19.5 Max
Figure.4 Dimension of Plastic Reel
MURATA MANUFACTURING CO., LTD
Reference only
P.13 /15
12.
Caution (Application, Fail-safe)
12-1.Application Limitations
This product, the PKGS type shock sensor, has been designed for hard-disk drive applications,
used in personal computers and consumer audio-visual equipments.
Please contact Murata before using this product in the applications listed below, which require
especially high reliability for the prevention of defects which might directly cause damage to the
third party's life, body or property, or when this product is intended for use in applications other
than those specified in this data sheet. We shall not be liable for any claims on the product in
case it is used in the listed applications below, without contacting us.
(1) Cellular phone
(2) Automotive equipment other than the above mentioned
(3) Outside use equipment
(6) Under sea equipment
(9) Transportation equipment (vehicles, trains, ships, etc.)
(4) Aircraft, Avionics equipment
(7) Power plant control equipment
(5) Aerospace equipment
(8) Medical equipment
(10) Industrial equipment
(11) Traffic signal equipment (12) Disaster prevention / crime prevention equipment
(13) Safety device / system (14) Military equipment (regardless of direct/indirect use)
(15) Applications of similar complexity and/or reliability requirements to the applications listed
in the above.
12-2.Fail-safe
Be sure to provide an appropriate fail-safe function on your product to prevent damage that may
be caused by the abnormal function or the failure of our product.
13.
Caution (Handling)
1) This product may be degraded by electrostatic discharge. We would suggest countermeasures
against electrostatic discharge, before handling this product.
2) Please evaluate this product in your product; with it mounted to a Printed Circuit Board (PCB) or
similar. We recommend that this product not be repeatedly mounted on or removed from a PCB
by soldering, because of the possibility of degradation due to excessive heating to this product or
electrostatic discharge (in case electrostatic discharge is not guarded against).
14.
Caution (Storage condition and usage environment)
1) Maximum storage period is for 6 months under the condition of 30°C and 70%RH before PCB
mounting. If this product is kept in an especially high humidity environment, the product may
degrade because of decreased insulation resistance value due to such conditions.
2) Please do not store and do not use this product in conditions that differ greatly from atmospheric
pressure, such as a vacuum space, a high mountain, water, and so on. A pressure cooker test is
not applicable for this product.
3) Please do not expose this product to dust, oil, corrosive gas, acid, or alkali. This product may be
degraded if exposed.
15.
Caution (Design)
1)Please use a charge amplifier circuit. This specification is only valid for use with charge amplifiers.
For instance, if you use a voltage amplifier circuit that is used with this product, we shall not be
liable for any claims.
2)Please do not apply DC bias voltage to this product, because it causes degradation of insulation
resistance value. Please try to keep minimizing the input bias current at front-end of amplifier
circuit as well.
3)Please thoroughly evaluate this product for noise immunity. Noise, coming from the product (EMI)
and/or generated by signal lines on PCB or other mechanical device (like a spindle motor), may
result in the miss-operation or the non-operation of this product.
4)Please thoroughly evaluate this product in terms of mechanically accelerated transmission system,
because this product may detect unexpected acceleration that is transmitted through PCB and/or
through the frame of your product. Mechanical resonance on your product or individual vibration
frequency of installed components/devices may create mutual interference, and it may result in
incorrect measurement by the sensor.
MURATA MANUFACTURING CO., LTD
Reference only
P.14 /15
5)Please do not apply excessive strain force or shock to this product that deviates from the
conditions in this specification, because mechanical failure or damage could occur.
6)Please thoroughly evaluate this product in your manufacturing if you will use any conformal coating
or potting process. These processes (for instance, in case resin type of material is used) could
result in package breaks, due to heat shrink. Also, humidity that remains inside of the case, may
affect circuit operation due to decreased insulation resistance value.
7)Physical and environmental characteristics for this product are described in this specification.
Please consider these characteristics in evaluating this part in your product.
8)Please carefully design the application’s housing to minimize dew and humidity. An amplifier circuit
would have high impedance, 50M ohm for instance, but this value may decrease under a high
humid environment. Due to this; you may not be able to see the intended performance from your
circuit design, unless you consider theses factors in your product design.
9)Please do not use this product in the presence of radiation rays or cosmic rays.
10)Please do not use this product in the presence of high electromagnetic fields.
11)Please consider the possibility of unexpected output signal-level generated by sharp temperature
change. Please evaluate this product under all expected environmental conditions.
recommend a fail-safe function to compensate for any unexpected signal levels.
We
12)Pyroelectric noise may be seen on the output signal of this product, where there is a temperature
variation (delta-t) around the product. Delta-t may likely occur by airflow that is generated by a
cooling fan that is often used in a computer. If your application requires a very small acceleration
resolution, less than 0.1G with 50Hz or less for instance, we would suggest shutting off the airflow
for increased accuracy in sensor detection.
13)This product is very sensitive to bending stress occurring on PCB, therefore please locate the
sensor in an area on the PCB that is unaffected by bending stresses.
16.
Caution (Mounting)
16-1. Reflow soldering
1)Please use the standard footprint as shown in the specification. If you use a different one, we shall
not be liable for any claims.
2)Please follow soldering conditions described in the specification. This product can permanently
stop operating if the piezoelectric characteristic is decreased due to excessive heating.
3)Please follow the recommended washing conditions, as described in the specification.
4)Please make sure to evaluate the soldering condition with this product mounted on your PCB.
<Reflow temperature profile (reference only)>
Peak Temp.
245 °C max.
230
Gradual cooling
in air
Pre-heating
in air
180
150
100
60 to 120 sec.
Within 30 sec.
16-2. Soldering Iron
Use iron (3mm diameter or less, 45W max.) and iron temp should be 300°C max.
within 3 sec. at only one point. Please take care to avoid soldering iron from touching the
product directly.
MURATA MANUFACTURING CO., LTD
Reference only
P.15 /15
17.
Note
1)Please make sure that the final product has been evaluated to all your product’s specifications,
with this product mounted inside.
2)All the items and parameters in this product specification have been prescribed on the premise that
our product is used for the purpose, under the conditions, and in the environment agreed upon
between us. You are requested not to use our product deviating from this product specification.
3)We consider it inappropriate to include any terms or conditions with regard to the business
transactions in the product’s specification, drawing, or other technical document. Therefore, if your
technical document includes any of the above items, such as warranty clause, product liability
clause, or intellectual property infringement liability clause, they will be deemed to be invalid.
MURATA MANUFACTURING CO., LTD
相关型号：
©2020 ICPDF网 联系我们和版权申明