RCER72E224K3M1H03A中文资料_数据手册_规格书

Reference only

䚷䚷䚷CAUTION

䚷䚷1. OPERATING VOLTAGE

When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p

value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the

voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated

for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage

containing these irregular voltage.

When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),

be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or

impulse withstand established for each equipment should be taken into considerations.

Voltage

DC Voltage

DC+AC Voltage

AC Voltage

Pulse Voltage(1)

Pulse Voltage(2)

Positional

Vo-p

Vp-p

Vo-p

Vp-p

Measurement

䚷䚷2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT

Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.

Be sure to take into account the heat generated by the capacitor itself.

When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-

generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),

applied voltage should be the load such as self-generated heat is within 20 °C on the condition of

atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1

capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal

capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other

components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s

characteristics and reliability.

䚷䚷3. FAIL-SAFE

Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that

may be caused by the abnormal function or the failure of our product.

䚷䚷4. OPERATING AND STORAGE ENVIRONMENT

The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store

capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the

like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify

that these processes do not affect product quality by testing the performance of a cleaned, bonded or

molded product in the intended equipment. Store the capacitors where the temperature and relative

humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.

䚷䚷5. VIBRATION AND IMPACT

Do not expose a capacitor or its leads to excessive shock or vibration during use.

䚷䚷6. SOLDERING

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the

capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may

result in thermal shocks that can crack the ceramic element.

䚷䚷7. BONDING AND RESIN MOLDING, RESIN COAT

In case of bonding, molding or coating this product, verify that these processes do not affect the quality

of capacitor by testing the performance of a bonded or molded product in the intended equipment.

In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins

containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer

coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short

circuit.

The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or

ceramic element cracking of a capacitor in a temperature cycling.

䚷䚷8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT

When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.

So please be careful not to give it mechanical stress.

EGLEDMNO03

1/18

Reference only

Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial

dispersion when the product is used.

䚷䚷9. LIMITATION OF APPLICATIONS

Please contact us before using our products for the applications listed below which require especially

high reliability for the prevention of defects which might directly cause damage to the third party’s life,

body or property.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

5. Medical equipment

7. Traffic signal equipment

4. Power plant control equipment

6. Transportation equipment (vehicles, trains, ships, etc.)

8. Disaster prevention / crime prevention equipment

9. Data-processing equipment exerting influence on public

10. Application of similar complexity and/or reliability requirements to the applications listed in the above.

NOTICE

䚷䚷1. CLEANING (ULTRASONIC CLEANING)

To perform ultrasonic cleaning, observe the following conditions.

Rinse bath capacity : Output of 20 watts per liter or less.

Rinsing time : 5 min maximum.

Do not vibrate the PCB/PWB directly.

Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.

䚷䚷2. SOLDERING AND MOUNTING

Insertion of the Lead Wire

• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.

• Insert the lead wire into the PCB with a distance appropriate to the lead space.

䚷䚷3. CAPACITANCE CHANGE OF CAPACITORS

• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)

䚷Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance

䚷slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on

䚷a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant

䚷circuit.

䚷Please contact us if you need a detail information.

䚷䚷䚷NOTE

1. Please make sure that your product has been evaluated in view of your specifications with our product

being mounted to your product.

2. You are requested not to use our product deviating from this specification.

EGLEDMNO03

2/18

Reference only

1. Application

This specification is applied to Leaded MLCC RCE series in accordance with

AEC-Q200 requirements used for Automotive Electronic equipment.

2. Rating

• Part Number Configuration

RCE

R7

2E

102

K

1

K1

Dimension Lead

(LxW) Style

H03

B

ex.)

Series

Temperature

Characteristics

Rated

Voltage

Capacitance

Tolerance

Individual

Package

Specification

• Temperature Characteristics

Standard

Temp.

Operating

Temp. Range

Code Temp. Char.

Temp. Range

Cap. Change

+/-15%

X7R

R7

-55到125°C

25°C

-55到125°C

(EIA code)

• Rated Voltage

Code

2E

2J

Rated voltage

DC250V

DC630V

DC1000V

3A

• Capacitance

The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.

ex.) In case of 102

10×10²= 1000pF

• Capacitance Tolerance

Code

K

Capacitance Tolerance

+/-10%

• Dimension (LxW)

Please refer to [ Part number list ].

• Lead Style

*Lead wire is "solder coated CP wire".

Code

B1

Lead Style

Straight type

Lead spacing (mm)

5.0+/-0.8

E1

K1

Straight taping type

Inside crimp type

5.0+0.6/-0.2

5.0+/-0.8

M1

Inside crimp taping type

5.0+0.6/-0.2

• Individual Specification

Murata’s control code.

Please refer to [ Part number list ].

• Package

Code

A

B

Package

Taping type of Ammo

Bulk type

7(,.$.8

3/18

Reference only

3. Marking

Temp. char.

:

Letter code : C (X7R char. Except dimension code : 1)

3 digit numbers

Code

Letter code : 4 (DC250V. Except dimension code : 1)

Letter code : 7 (DC630V)

Capacitance

Capacitance tolerance

Rated voltage

Letter code : A (DC1000V)

Company name code

:

Abbreviation :

(Except dimension code : 1)

(Ex.)

Rated voltage

DC250V

103K

DC630V

DC1000V

Dimension code

1

㸫

102

473

153

2

3,4

5

KAC

K4C

K7C

224

K4C

333

KAC

104

K7C

474

K4C

104

KAC

224

M7C

7(,.$.8

4/18

Reference only

4. Part number list

Unit : mm

DC

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RCER72E102K1K1H03B

RCER72E152K1K1H03B

RCER72E222K1K1H03B

RCER72E332K1K1H03B

RCER72E472K1K1H03B

RCER72E682K1K1H03B

RCER72E103K1K1H03B

RCER72E153K1K1H03B

RCER72E223K1K1H03B

RCER72E333K2K1H03B

RCER72E473K2K1H03B

RCER72E683K2K1H03B

RCER72E104K2K1H03B

RCER72E154K3K1H03B

RCER72E224K3K1H03B

RCER72E334K4K1H03B

RCER72E474K4K1H03B

RCER72E684K5B1H03B

RCER72E105K5B1H03B

X7R

250

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

4.0

3.5

5.0 3.15

1K1

2K1

3K1

4K1

5B1

500

4.0

5.5

7.5

3.5

4.0

5.0

5.5

7.5

5.0

6.0

7.5

8.0

-

250 10000pF

250 15000pF

250 22000pF

250 33000pF

250 47000pF

250 68000pF

250

0.10μF

0.15μF

0.22μF

0.33μF

0.47μF

0.68μF

1.0μF

5.0

4.0

-

PNLIST

5/18

Reference only

Unit : mm

DC

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RCER72J102K2K1H03B

RCER72J152K2K1H03B

RCER72J222K2K1H03B

RCER72J332K2K1H03B

RCER72J472K2K1H03B

RCER72J682K2K1H03B

RCER72J103K2K1H03B

RCER72J153K2K1H03B

RCER72J223K2K1H03B

RCER72J333K3K1H03B

RCER72J473K3K1H03B

RCER72J683K4K1H03B

RCER72J104K4K1H03B

RCER72J154K5B1H03B

RCER72J224K5B1H03B

X7R

630

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

5.5

4.0

5.0 3.15

2K1

3K1

4K1

5B1

500

5.5

7.5

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

630 10000pF

630 15000pF

630 22000pF

630 33000pF

630 47000pF

630 68000pF

5.0

4.0

630

0.10μF

0.15μF

0.22μF

-

PNLIST

6/18

Reference only

Unit : mm

DC

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RCER73A102K2K1H03B

RCER73A152K2K1H03B

RCER73A222K2K1H03B

RCER73A332K2K1H03B

RCER73A472K2K1H03B

RCER73A682K2K1H03B

RCER73A103K2K1H03B

RCER73A153K3K1H03B

RCER73A223K3K1H03B

RCER73A333K4K1H03B

RCER73A473K4K1H03B

RCER73A683K5B1H03B

RCER73A104K5B1H03B

X7R 1000

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

5.5

4.0

5.0 3.15

2K1

3K1

4K1

5B1

500

5.5

7.5

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

X7R 1000 10000pF

X7R 1000 15000pF

X7R 1000 22000pF

X7R 1000 33000pF

X7R 1000 47000pF

X7R 1000 68000pF

5.0

4.0

X7R 1000

0.10μF

-

PNLIST

7/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RCER72E102K1M1H03A X7R 250

RCER72E152K1M1H03A X7R 250

RCER72E222K1M1H03A X7R 250

RCER72E332K1M1H03A X7R 250

RCER72E472K1M1H03A X7R 250

RCER72E682K1M1H03A X7R 250

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

4.0

5.5

7.5

3.5

5.0 3.15 16.0

1M1

2M1

3M1

4M1

5E1

2000

1500

3.5

4.0

5.0

5.5

7.5

5.0

6.0

7.5

8.0

-

RCER72E103K1M1H03A X7R 250 10000pF

RCER72E153K1M1H03A X7R 250 15000pF

RCER72E223K1M1H03A X7R 250 22000pF

RCER72E333K2M1H03A X7R 250 33000pF

RCER72E473K2M1H03A X7R 250 47000pF

RCER72E683K2M1H03A X7R 250 68000pF

RCER72E104K2M1H03A X7R 250

RCER72E154K3M1H03A X7R 250

RCER72E224K3M1H03A X7R 250

RCER72E334K4M1H03A X7R 250

RCER72E474K4M1H03A X7R 250

RCER72E684K5E1H03A X7R 250

RCER72E105K5E1H03A X7R 250

0.10μF

0.15μF

0.22μF

0.33μF

0.47μF

0.68μF

1.0μF

5.0

4.0 16.0

4.0 17.5

-

PNLIST

8/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RCER72J102K2M1H03A X7R 630

RCER72J152K2M1H03A X7R 630

RCER72J222K2M1H03A X7R 630

RCER72J332K2M1H03A X7R 630

RCER72J472K2M1H03A X7R 630

RCER72J682K2M1H03A X7R 630

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

5.5

7.5

4.0

5.0 3.15 16.0

2M1

3M1

4M1

5E1

2000

1500

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

RCER72J103K2M1H03A X7R 630 10000pF

RCER72J153K2M1H03A X7R 630 15000pF

RCER72J223K2M1H03A X7R 630 22000pF

RCER72J333K3M1H03A X7R 630 33000pF

RCER72J473K3M1H03A X7R 630 47000pF

RCER72J683K4M1H03A X7R 630 68000pF

5.0

4.0 16.0

4.0 17.5

RCER72J104K4M1H03A X7R 630

RCER72J154K5E1H03A X7R 630

RCER72J224K5E1H03A X7R 630

0.10μF

0.15μF

0.22μF

-

PNLIST

9/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RCER73A102K2M1H03A X7R 1000

RCER73A152K2M1H03A X7R 1000

RCER73A222K2M1H03A X7R 1000

RCER73A332K2M1H03A X7R 1000

RCER73A472K2M1H03A X7R 1000

RCER73A682K2M1H03A X7R 1000

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

±10%

5.5

7.5

4.0

5.0 3.15 16.0

2M1

3M1

4M1

5E1

2000

1500

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

RCER73A103K2M1H03A X7R 1000 10000pF

RCER73A153K3M1H03A X7R 1000 15000pF

RCER73A223K3M1H03A X7R 1000 22000pF

RCER73A333K4M1H03A X7R 1000 33000pF

RCER73A473K4M1H03A X7R 1000 47000pF

RCER73A683K5E1H03A X7R 1000 68000pF

5.0

4.0 16.0

4.0 17.5

RCER73A104K5E1H03A X7R 1000

0.10μF

-

PNLIST

10/18

Reference only

5. AEC-Q200 Murata Standard Specifications and Test Methods

AEC-Q200

No.

Specification

AEC-Q200 Test Method

Test Item

Pre-and Post-Stress

Electrical Test

1

-

2

3

High

Appearance

No defects or abnormalities.

Sit the capacitor for 1000±12h at 150±3°C. Let sit for 24±2h at,

*room condition then measure.

Temperature Capacitance within ±12.5%

Exposure

(Storage)

Change

D.F.

0.04 max.

•Pretreatment

I.R.

More than 1,000MΩ or 50MΩ䞉μF

(Whichever is smaller)

No defects or abnormalities.

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

Perform the 1000 cycles according to the four heat treatments

listed in the following table. Let sit for 24±2 h at *room condition,

then measure.

Temperature Appearance

Cycling

Capacitance within ±12.5%

Change

D.F.

0.05 max.

I.R.

1,000MΩ or 50MΩ䞉μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

4

Moisture

Appearance

No defects or abnormalities

Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)

treatment shown below, 10 consecutive times.

Let sit for 24±2 h at *room condition, then measure.

Resistance

Capacitance within ±12.5%

Change

D.F.

I.R.

0.05 max.

500MΩ or 25MΩ·μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

5

Biased

Appearance

No defects or abnormalities

Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)

at 85±3°C and 80 to 85% humidity for 1000±12h.

Remove and let sit for 24±2 h at *room condition, then measure.

The charge/discharge current is less than 50mA.

Humidity

Capacitance within ±12.5%

Change

D.F.

I.R.

0.05 max.

500MΩ or 25MΩ·μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

Apply voltage in Table for 1000±12h at 125±3°C.

Let sit for 24±2 h at *room condition, then measure.

The charge/discharge current is less than 50mA.

•Pretreatment

6

Operational

Life

Appearance

No defects or abnormalities

Capacitance within ±12.5%

Change

D.F.

I.R.

0.04 max.

1,000MΩ or 50MΩ·μF min.

(Whichever is smaller)

Apply test voltage for 60±5 min at test temperature.

Remove and let sit for 24±2 h at *room condition.

External Visual

7

8

9

No defects or abnormalities.

Within the specified dimensions.

To be easily legible.

Visual inspection.

Physical Dimension

Marking

Using calipers and micrometers.

Visual inspection.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE03C

11/18

Reference only

AEC-Q200

Test Item

No.

Specification

AEC-Q200 Test Method

10 Resistance

to Solvents

Appearance

No defects or abnormalities.

Per MIL-STD-202 Method 215

Capacitance Within the specified tolerance.

Solvent 1 : 1 part (by volume) of isopropyl alcohol

3 parts (by volume) of mineral spirits

D.F.

I.R.

0.025 max.

More than 10,000MΩ or 500 MΩ䞉μF

(Whichever is smaller)

Solvent 2 : Terpene defluxer

Solvent 3 : 42 parts (by volume) of water

1 part (by volume) of propylene glycol

monomethyl ether

1 part (by volume) of monoethanolamine

11 Mechanical

Shock

Appearance

No defects or abnormalities.

Three shocks in each direction should be applied along 3

mutually perpendicular axes of the test specimen (18 shocks).

The specified test pulse should be Half-sine and should have a

duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 2,000Hz.

The frequency range, from 10 to 2000Hz and return to 10Hz,

should be traversed in approximately 20 min. This motion

should be applied for 12 items in each 3 mutually perpendicular

directions (total of 36 times).

Capacitance Within the specified tolerance.

D.F.

0.025 max.

12 Vibration

Appearance

No defects or abnormalities.

Capacitance Within the specified tolerance.

D.F.

0.025 max.

13-1 Resistance

to Soldering

Heat

Appearance

No defects or abnormalities.

The lead wires should be immersed in the melted solder 1.5 to

2.0mm from the root of terminal at 260±5°C for 10±1 seconds.

Capacitance Within ±7.5%

Change

(Non-

Dielectric

Strength

No defects

• Pre-treatment

Preheat)

Capacitor should be stored at 150+0/-10°C for one

hour, then place at *room condition for 24±2 hours before initial

measurement.

(Between

terminals)

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.

Then, the lead wires should be immersed in the melted solder 1.5 to

2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.

13-2 Resistance

to Soldering

Heat

Appearance

No defects or abnormalities.

Capacitance Within ±7.5%

Change

(On-

Dielectric

Strength

No defects

Preheat)

• Pre-treatment

(Between

terminals)

Capacitor should be stored at 150+0/-10°C for one hour, then place at

*room condition for 24±2 hours before initial measurement.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Test condition

13-3 Resistance

to Soldering

Heat

Appearance

No defects or abnormalities.

Capacitance Within ±7.5%

Change

Termperature of iron-tip : 350±10°C

Soldering time

: 3.5±0.5 seconds

(soldering

Dielectric

Strength

No defects

Soldering position

iron method)

Straight Lead : 1.5 to 2.0mm from the root of terminal.

Crimp Lead : 1.5 to 2.0mm from the end of lead bend.

(Between

terminals)

• Pre-treatment

Capacitor should be stored at 150+0/-10°C for one hour, then place at

*room condition for 24±2 hours before initial measurement.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Perform the 300 cycles according to the two heat treatments listed in

14 Thermal

Shock

Appearance

No defects or abnormalities.

Capacitance within ±12.5%

Change

the following table (Maximum transfer time is 20s.). Let sit for 24±2 h at

*room condition, then measure.

D.F.

I.R.

0.05 max.

1,000MΩ or 50MΩ䞉μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

Per AEC-Q200-002

15 ESD

Appearance

No defects or abnormalities

Capacitance Within the specified tolerance

D.F.

I.R.

0.025 max.

More than 10,000MΩ or 100 MΩ䞉μF

(Whichever is smaller)

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE03C

12/18

Reference only

AEC-Q200

Test Item

No.

Specifications

AEC-Q200 Test Method

Lead wire should be soldered with uniform

coating on the axial direction over 95% of

the circumferential direction.

16 Solderability

Should be placed into steam aging for 8h±15 min.

The terminal of capacitor is dipped into a solution of ethanol

(JIS K 8101) and rosin (JIS K 5902) (25% rosin in weight

propotion).Immerse in solder solution for 2±0.5 seconds.

In both cases the depth of dipping is up to about 1.5 to 2mm from

the terminal body.

Temp. of solder :

245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)

235±5°C H60A or H63A Eutectic Solder

Visual inspection.

No defects or abnormalities.

Within the specified tolerance.

0.025 max.

17 Electrical

Characte-

rization

Apperance

Capacitance

D.F.

The capacitance/D.F. should be measured at 25°C at the frequency

and voltage shown in the table.

I.R.

Between 10,000MΩ or 100MΩ䞉μF min.

The insulation resistance should be measured with DC500V

(DC250V in case of rated voltage : DC250V) at 25 °C within 2 min.

of charging.

Terminals (Whichever is smaller)

Dielectric

Strength

Between No defects or abnormalities

Terminals

The capacitor should not be damaged when voltage inTable is

applied between the terminations for 1 to 5 seconds.

(Charge/Discharge current 䍺 50mA.)

Body

No defects or abnormalities

The capacitor is placed in a container with metal balls of 1mm

diameter so that each terminal, short-circuit is kept approximately

2mm from the balls, and 200% of the rated DC voltage(DC1300V

in case of rated voltage : DC630V,DC1000V) is impressed for 1 to

5 seconds between capacitor terminals and metal balls.

(Charge/Discharge current ӌ 50mA.)

Insulation

Termination not to be broken or loosened.

18 Terminal

Strength

Tensile

As in the figure, fix the capacitor body, apply the force gradually

to each lead in the radial direction of the capacitor until reaching

10N and then keep the force applied for 10±1 seconds.

Strength

F

Termination not to be broken or loosened.

Bending

Strength

Each lead wire should be subjected to a force of 2.5N and then

be bent 90° at the point of egress in one direction. Each wire is

then returned to the original position and bent 90° in the opposite

direction at the rate of one bend per 2 to 3 seconds.

The capacitance change should be measured after 5min. at

each specified temperature step.

Capacitance

Temperature

Characteristics

Within ±15%

19

The ranges of capacitance change compared with the above

25°C value over the temperature ranges shown in the table

should be within the specified ranges.

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 h at *room condition.

Perform the initial measurement.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE03C

13/18

Reference only

6. Packing specification

䞉Bulk type (Packing style code : B)

The size of packing case and packing way

Polyethylene bag

Partition

270 max.

125 max.

Unit : mm

340 max.

The number of packing = ^*1Packing quantity 㽢 ^*2n

*1 : Please refer to [Part number list].

*2 : Standard n = 20 (bag)

Note)

The outer package and the number of outer packing be changed by the order getting amount.

JKBCRPE02

14/18

Reference only

䞉Ammo pack taping type (Packing style code : A)

䚷䚷䚷䚷䚷䚷A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.

䚷䚷䚷䚷䚷䚷When body of the capacitor is piled on other body under it.

The size of packing case and packing way

240 max.

Position of label

340 max.

Unit : mm

51 max.

Hold down tape

Capacitor

Base tape

Hold down

tape upper

EKTRPE01

15/18

Reference only

7. Taping specification

7-1. Dimension of capacitors on tape

Straight taping type < Lead Style : E1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

ڹ

h2

ڹ

h1

Marking

ڹ

S

e

P1

F

Id

ID0

P0

Unit : mm

Item

Code

Dimensions

Remarks

Pitch of component

P

P0

F

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Pitch of sprocket hole

Lead spacing

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

'S

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

17.5+/-0.5

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Position of sprocket hole

For straight lead type

W1

H

Protrusion length

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness.

Total thickness of tape and lead wire

t2

2.0 max.㸦Dimension code㸸U㸧

1.0 max.㸦except as above㸧

11.0+0/-1.0

'h1

'h2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

9.5 min.

Hold down tape position

1.5+/-1.5

2.0 max.㸦Dimension code㸸U㸧

1.5 max.㸦except as above㸧

Coating extension on lead

e

ETP1E101B

16/18

Reference only

Inside crimp taping type < Lead Style : M1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

Δh1

Marking

Δh2

ΔS

e

P1

F

Φd

ΦD0

P0

Unit : mm

Item

Code

P

Dimensions

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

P0

F

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

ΔS

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

Position of sprocket hole

W1

Lead distance between reference and

bottom plane

H0

16.0+/-0.5

Protrusion length

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness

Total thickness of tape and lead wire

t2

䚷䚷䚷2.0 max. (Dimension code : W)

䚷䚷䚷1.0 max. (except as above)

11.0+0/-1.0

䂴h1

䂴h2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

e

9.5 min.

Hold down tape position

Coating extension on lead

1.5+/-1.5

Up to the end of crimp

ETP1M101A

17/18

Reference only

ࠉ

7-2. Splicing way of tape

1) Adhesive force of tape is over 3N at test condition as below.

W

Hold down tape

Base tape

2) Splicing of tape

ࠉ

ࠉࠉ

a) When base tape is spliced

•Base tape shall be spliced by cellophane tape.

(Total tape thickness shall be less than 1.05mm.)

Progress direction

in production line

Hold down tape

Base tape

About 30 to 50

No lifting for the

Cellophane tape

direction of

progressing

Unit : mm

ࠉ

ࠉࠉ

b) When hold down tape is spliced

ࠉ

ࠉࠉ

•Hold down tape shall be spliced with overlapping.

ꢀꢀꢀꢀꢀꢀꢀꢀ(Total tape thickness shall be less than 1.05mm.)

20 to 30

Hold down tape

Base tape

Unit : mm

Progress direction

in production line

ࠉ

ࠉࠉ

c) When both tape are spliced

•Base tape and hold down tape shall be spliced with splicing tape.

ETP2R01

18/18

型号	制造商	描述	价格	文档
RCER72E332K1K1H03B	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E332K1M1H03A	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E333K2K1H03B	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E333K2M1H03A	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E334K4K1H03B	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E334K4M1H03A	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E472K1K1H03B	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E472K1M1H03A	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E473K2K1H03B	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格
RCER72E473K2M1H03A	MURATA	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]	获取价格

RCER72E224K3M1H03A

RCER72E224K3M1H03A 概述

RCER72E224K3M1H03A 数据手册

RCER72E224K3M1H03A 相关器件

RCER72E224K3M1H03A 相关文章

热门型号