RPE5C1H5R0C2K1B03B [MURATA]
Ceramic Capacitor, Multilayer, Ceramic, 50V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.000005uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT;
| 型号： | RPE5C1H5R0C2K1B03B |
| 厂家： | 
muRata |
| 描述： | Ceramic Capacitor, Multilayer, Ceramic, 50V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.000005uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT 电容器 |
| 文件： | 总54页 (文件大小：1613K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Radial Lead Type
Monolithic Ceramic
Capacitors
Cat.No.C49E-21
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
EU RoHS Compliant
•
All the products in this catalog comply with EU RoHS.
•
EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment."
•
For more details, please refer to our website 'Murata's Approach for EU RoHS'
(http://www.murata.com/info/rohs.html).
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
1
CONTENTS
Part Numbering
2
4
2
3
4
5
1
RPE Series (DC25V-DC100V)
Marking
5
Temperature Compensating Type, C0G Characteristics
High Dielectric Constant Type, X7R Characteristics
High Dielectric Constant Type, Y5V Characteristics
Specifications and Test Methods
6
9
10
12
15
16
16
17
19
20
20
21
24
27
28
28
30
33
34
37
38
38
40
42
42
43
44
45
46
48
51
2
3
RPE Series Small Size, Large Capacitance (DC50V)
Marking
High Dielectric Constant Type, X7R Characteristics
Specifications and Test Methods
RH Series 150°C max. (for Automotive) (DC50V-DC100V)
Marking
Temperature Compensating Type, X8G Characteristics
High Dielectric Constant Type, X8L Characteristics
Specifications and Test Methods
4
RDE Series (For Commercial Use Only) (DC25V-DC630V)
Marking
Temperature Compensating Type, C0G Characteristics
High Dielectric Constant Type, X7R/ X7S Characteristics
High Dielectric Constant Type, F/ Y5V Characteristics
Specifications and Test Methods
5
RDE Series Large Capacitance and High Allowable Ripple Current (For Commercial Use Only) (DC250V-DC630V)
Marking
High Dielectric Constant Type, X7T Characteristics
Specifications and Test Methods
Reference Data (Typical Example)
RPE Series
RPE Series Small Size, Large Capacitance
RH Series
RDE Series
Packaging
!Caution
Notice
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
o Part Numbering
Radial Lead Type Monolithic Ceramic Capacitors
(Part Number)
RP
E
R7 1H 104
K
2
M1 A03
A
q
w
e
r
t
y
u
i
o
!
qProduct ID
wSeries/Terminal
Product ID
Series/Terminal
RP
RH
RD
E
E/D
E
Radial Lead Type Monolithic Ceramic Capacitors (DC25V-DC100V)
Radial Lead Type Monolithic Ceramic Capacitors 150°C max. (for Automotive) (DC50V-DC100V)
Radial Lead Type Monolithic Ceramic Capacitors (For Commercial Use Only) (DC25V-DC630V)
eTemperature Characteristics
Temperature
Code
Reference
Characteristics Temperature
Temperature
Range
Capacitance Change or
Temperature Coefficient
Operating
Temperature Range
5C
5G
C7
D7
F1
F5
C0G*
X8G*
X7S
X7T
F
25°C
25°C
25°C
25°C
20°C
25°C
25 to 125°C
25 to 150°C
-55 to 125°C
-55 to 125°C
-25 to 85°C
-30 to 85°C
-55 to 125°C
125 to 150°C
-55 to 125°C
0±30ppm/°C
0±30ppm/°C
±22%
-55 to 125°C
-55 to 150°C
-55 to 125°C
-55 to 125°C
-25 to 85°C
-30 to 85°C
+22, -33%
+30, -80%
+22, -82%
±15%
Y5V
L8
R7
X8L
X7R
25°C
25°C
-55 to 150°C
-55 to 125°C
+15, -40%
±15%
* Please refer to table for Capacitance change under reference temperature.
• Capacitance change from each temperature
Capacitance Change from 25˚C (% )
-30˚C
Char.
Nominal Values (ppm/˚C) *1
-55˚C
-10˚C
Max.
Min.
Max.
Min.
Max.
Min.
C0G
X8G
0±30
0.58
-0.24
0.40
-0.17
0.25
-0.11
*1: Nominal values denote the temperature coefficient within a range of 25 to 125˚C.
rRated Voltage
yCapacitance Tolerance
Code
1E
Rated Voltage
DC25V
Capacitance Temperature
Tolerance Characteristics
Capacitance
Step
Code
1H
DC50V
C
D
J
±0.25pF
C0G
V5pF : 1pF Step
6 to 9pF : 1pF Step
U10 : E12 Series
2A
DC100V
DC250V
DC450V
DC630V
±0.5pF
2E
±5%
C0G/X8G
2W
2J
X7S/X7T/X7R/
X8L
K
±10%
E6 Series
X7S/X7T/X7R/
X8L
M
Z
±20%
E3 Series
E3 Series
tCapacitance
Expressed by three-digit alphanumerics. The unit is pico-farad
(pF). The first and second figures are significant digits, and the
third figure expresses the number of zeros that follow the two
numbers.
+80% , -20%
F/Y5V
If there is a decimal point, it is expressed by the capital letter "R."
In this case, all figures are significant digits.
Continued on the following page.
2
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
uDimensions (LxW)
oIndividual Specification Code
Expressed by three-digit alphanumerics
Code
Dimensions (LxW)
0
1
4.0g3.5mm or 5.0g3.5mm (Depends on Part Number List)
4.0g3.5mm or 4.5g3.5mm or 5.0g3.5mm (Depends on Part Number List)
5.0g3.5mm or 5.5g4.0mm or 5.7g4.5mm (Depends on Part Number List)
5.0g4.5mm or 5.5g5.0mm or 6.0g5.5mm (Depends on Part Number List)
7.5g7.5mm*
!Packaging
2
Code
A
Packaging
3
Ammo Pack
Bulk
5
B
6
10.0g10.0mm
7
12.5g12.5mm
8
7.5g5.5mm
U
W
7.7g12.5mm*
5.5g7.5mm
* DC630V: W+0.5mm
iLead Style
Code
A2
Lead Style
Straight Long
Lead Spacing
2.5mm
B1
Straight Long
5.0mm
C1
Straight Long
10.0mm
2.5mm
DB
Straight Taping
Straight Taping
Inside Crimp
E1/E2
K1
5.0mm
5.0mm
M1/M2
P1
Inside Crimp Taping
Outside Crimp
5.0mm
2.5mm
S1/S2
Outside Crimp Taping
2.5mm
Lead distance between reference and bottom planes.
M1, S1: H0 = 16.0±0.5mm
M2, S2: H0 = 20.0±0.5mm
E1: H = 17.5±0.5mm
E2: H = 20.0±0.5mm
3
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
1
Radial Lead Type Monolithic Ceramic Capacitors
RPE Series (DC25V-DC100V)
L max.
T max.
■ Features
1. The RPE series capacitors have small dimensions,
large capacitance, and a capacity volume ratio of
10 micro F/cm cubed, close to that of electrolytic
capacitors. They do not have polarity.
2. Excellent frequency characteristics and due to
their small internal inductance are suitable for
high frequencies.
ød : 0.5±0.05
F±0.8
3. Not coated with wax so there is no change in
their exterior appearance due to the outflow of
wax during soldering or solvent during cleansing.
4. They are highly nonflammable, having characteristics
equivalent to the UL94V-0 standard.
Dimensions code: 2/3
Lead style code: P1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
(in mm)
Solder Coated CP Wire
L max.
T max.
ød : 0.5±0.05
F±0.8
Dimensions code: 2/3/8
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
(in mm)
Solder Coated CP Wire
L max.
T max.
■ Dimensions
Dimensions and
Lead Style Code
Dimensions (mm)
L
W
3.5
W1
5.0
5.0
6.3
6.3
-
T
F
d
2P1/2S1/2S2
2K1/2M1/2M2
3P1/3S1/3S2
3K1/3M1/3M2
5B1/5E1/5E2
6B1/6E1/6E2
7C1
5.0
5.0
5.0
5.0
7.5
10.0
12.5
7.5
2.5
5.0
2.5
5.0
5.0
5.0
10.0
5.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
3.5
4.5
See
the individual
product
ød : 0.5±0.05
4.5
7.5
F±0.8
specifications
10.0
12.5
5.5
-
Dimensions code: 5/6/7
Lead style code: B1/C1
-
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
8K1/8M1/8M2
8.0
(in mm)
Continued on the following page.
4
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
■ Marking
1
Type
Temperature Compensating Type
C0G
High Dielectric Constant Type
Temp. Char.
X7R
Y5V
Dimensions
Code
Individual
Specification
Code
102J
5A
222K
224Z
App
Bpp
Zpp
Marked on both sides
2
Individual
Specification
Code
682
224
474
M J5A
MK5C
M Z5F
Except
App
Bpp
Zpp
M
684
—
—
—
—
3, 8
K5C
M
225
5, 6, 7
K5C
Marked with code (C0G char.: A, X7R char.: C, Y5V char.: F)
A part is omitted (Please refer to the marking example.)
Temperature Characteristics
Under 100pF: Actual value 100pF and over: marked with 3 figures
Marked with code
Nominal Capacitance
Capacitance Tolerance
Marked with code (DC25V: 2, DC50V: 5, DC100V: 1)
A part is omitted (Please refer to the marking example.)
Rated Voltage
M
Marked with
Manufacturer's Identification
A part is omitted (Please refer to the marking example.)
5
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
1
Temperature Compensating Type, C0G Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RPE5C1H1R0C2ppB03p
RPE5C1H1R0C2ppB03p
RPE5C1H2R0C2ppB03p
RPE5C1H2R0C2ppB03p
RPE5C1H3R0C2ppB03p
RPE5C1H3R0C2ppB03p
RPE5C1H4R0C2ppB03p
RPE5C1H4R0C2ppB03p
RPE5C1H5R0C2ppB03p
RPE5C1H5R0C2ppB03p
RPE5C1H6R0D2ppB03p
RPE5C1H6R0D2ppB03p
RPE5C1H7R0D2ppZ03p
RPE5C1H7R0D2ppZ03p
RPE5C1H8R0D2ppZ03p
RPE5C1H8R0D2ppZ03p
RPE5C1H9R0D2ppZ03p
RPE5C1H9R0D2ppZ03p
RPE5C1H100J2ppZ03p
RPE5C1H100J2ppZ03p
RPE5C1H120J2ppZ03p
RPE5C1H120J2ppZ03p
RPE5C1H150J2ppZ03p
RPE5C1H150J2ppZ03p
RPE5C1H180J2ppZ03p
RPE5C1H180J2ppZ03p
RPE5C1H220J2ppZ03p
RPE5C1H220J2ppZ03p
RPE5C1H270J2ppZ03p
RPE5C1H270J2ppZ03p
RPE5C1H330J2ppZ03p
RPE5C1H330J2ppZ03p
RPE5C1H390J2ppZ03p
RPE5C1H390J2ppZ03p
RPE5C1H470J2ppZ03p
RPE5C1H470J2ppZ03p
RPE5C1H560J2ppZ03p
RPE5C1H560J2ppZ03p
RPE5C1H680J2ppZ03p
RPE5C1H680J2ppZ03p
RPE5C1H820J2ppZ03p
RPE5C1H820J2ppZ03p
RPE5C1H101J2ppA03p
RPE5C1H101J2ppA03p
RPE5C1H121J2ppA03p
RPE5C1H121J2ppA03p
RPE5C1H151J2ppA03p
RPE5C1H151J2ppA03p
RPE5C1H181J2ppA03p
RPE5C1H181J2ppA03p
RPE5C1H221J2ppA03p
RPE5C1H221J2ppA03p
RPE5C1H271J2ppA03p
RPE5C1H271J2ppA03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
1.0 ±0.25pF
1.0 ±0.25pF
2.0 ±0.25pF
2.0 ±0.25pF
3.0 ±0.25pF
3.0 ±0.25pF
4.0 ±0.25pF
4.0 ±0.25pF
5.0 ±0.25pF
5.0 ±0.25pF
6.0 ±0.5pF
6.0 ±0.5pF
7.0 ±0.5pF
7.0 ±0.5pF
8.0 ±0.5pF
8.0 ±0.5pF
9.0 ±0.5pF
9.0 ±0.5pF
10 ±5%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
10 ±5%
12 ±5%
12 ±5%
15 ±5%
15 ±5%
18 ±5%
18 ±5%
22 ±5%
22 ±5%
27 ±5%
27 ±5%
33 ±5%
33 ±5%
39 ±5%
39 ±5%
47 ±5%
47 ±5%
56 ±5%
56 ±5%
68 ±5%
68 ±5%
82 ±5%
82 ±5%
100 ±5%
100 ±5%
120 ±5%
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
Continued on the following page.
6
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
1
(mm)
(mm)
Taping (1)
RPE5C1H331J2ppA03p
RPE5C1H331J2ppA03p
RPE5C1H391J2ppA03p
RPE5C1H391J2ppA03p
RPE5C1H471J2ppA03p
RPE5C1H471J2ppA03p
RPE5C1H561J2ppA03p
RPE5C1H561J2ppA03p
RPE5C1H681J2ppA03p
RPE5C1H681J2ppA03p
RPE5C1H821J2ppA03p
RPE5C1H821J2ppA03p
RPE5C1H102J2ppA03p
RPE5C1H102J2ppA03p
RPE5C1H122J2ppA03p
RPE5C1H122J2ppA03p
RPE5C1H152J2ppA03p
RPE5C1H152J2ppA03p
RPE5C1H182J2ppC03p
RPE5C1H182J2ppA03p
RPE5C1H222J2ppC03p
RPE5C1H222J2ppA03p
RPE5C1H272J2ppC03p
RPE5C1H272J2ppA03p
RPE5C1H332J2ppC03p
RPE5C1H332J2ppA03p
RPE5C1H392J2ppC03p
RPE5C1H392J2ppA03p
RPE5C1H472J2ppC03p
RPE5C1H472J2ppA03p
RPE5C1H562J2ppC03p
RPE5C1H562J2ppA03p
RPE5C1H682J2ppC03p
RPE5C1H822J2ppC03p
RPE5C1H103J2ppC03p
RPE5C2A1R0C2ppB03p
RPE5C2A1R0C2ppB03p
RPE5C2A2R0C2ppB03p
RPE5C2A2R0C2ppB03p
RPE5C2A3R0C2ppB03p
RPE5C2A3R0C2ppB03p
RPE5C2A4R0C2ppB03p
RPE5C2A4R0C2ppB03p
RPE5C2A5R0C2ppB03p
RPE5C2A5R0C2ppB03p
RPE5C2A6R0D2ppB03p
RPE5C2A6R0D2ppB03p
RPE5C2A7R0D2ppZ03p
RPE5C2A7R0D2ppZ03p
RPE5C2A8R0D2ppZ03p
RPE5C2A8R0D2ppZ03p
RPE5C2A9R0D2ppZ03p
RPE5C2A9R0D2ppZ03p
RPE5C2A100J2ppZ03p
RPE5C2A100J2ppZ03p
RPE5C2A120J2ppZ03p
RPE5C2A120J2ppZ03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
50
50
330 ±5%
330 ±5%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
5.0
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
K1
K1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
S1
M1
S1
S2
M2
S2
50
390 ±5%
2.5
50
390 ±5%
2.5
M1
S1
M2
S2
50
470 ±5%
2.5
50
470 ±5%
2.5
M1
S1
M2
S2
50
560 ±5%
2.5
50
560 ±5%
2.5
M1
S1
M2
S2
50
680 ±5%
2.5
50
680 ±5%
2.5
M1
S1
M2
S2
50
820 ±5%
2.5
50
820 ±5%
2.5
M1
S1
M2
S2
50
1000 ±5%
1000 ±5%
1200 ±5%
1200 ±5%
1500 ±5%
1500 ±5%
1800 ±5%
1800 ±5%
2200 ±5%
2200 ±5%
2700 ±5%
2700 ±5%
3300 ±5%
3300 ±5%
3900 ±5%
3900 ±5%
4700 ±5%
4700 ±5%
5600 ±5%
5600 ±5%
6800 ±5%
8200 ±5%
10000 ±5%
1.0 ±0.25pF
1.0 ±0.25pF
2.0 ±0.25pF
2.0 ±0.25pF
3.0 ±0.25pF
3.0 ±0.25pF
4.0 ±0.25pF
4.0 ±0.25pF
5.0 ±0.25pF
5.0 ±0.25pF
6.0 ±0.5pF
6.0 ±0.5pF
7.0 ±0.5pF
7.0 ±0.5pF
8.0 ±0.5pF
8.0 ±0.5pF
9.0 ±0.5pF
9.0 ±0.5pF
10 ±5%
2.5
50
2.5
M1
S1
M2
S2
50
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
2.5
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
S1
M2
S2
50
50
M1
M1
M1
M1
S1
M2
M2
M2
M2
S2
50
50
50
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
10 ±5%
2.5
M1
S1
M2
S2
12 ±5%
2.5
12 ±5%
2.5
M1
M2
Continued on the following page.
7
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
1
(mm)
(mm)
Taping (1)
RPE5C2A150J2ppZ03p
RPE5C2A150J2ppZ03p
RPE5C2A180J2ppZ03p
RPE5C2A180J2ppZ03p
RPE5C2A220J2ppZ03p
RPE5C2A220J2ppZ03p
RPE5C2A270J2ppZ03p
RPE5C2A270J2ppZ03p
RPE5C2A330J2ppZ03p
RPE5C2A330J2ppZ03p
RPE5C2A390J2ppZ03p
RPE5C2A390J2ppZ03p
RPE5C2A470J2ppZ03p
RPE5C2A470J2ppZ03p
RPE5C2A560J2ppZ03p
RPE5C2A560J2ppZ03p
RPE5C2A680J2ppZ03p
RPE5C2A680J2ppZ03p
RPE5C2A820J2ppZ03p
RPE5C2A820J2ppZ03p
RPE5C2A101J2ppA03p
RPE5C2A101J2ppA03p
RPE5C2A121J2ppA03p
RPE5C2A121J2ppA03p
RPE5C2A151J2ppA03p
RPE5C2A151J2ppA03p
RPE5C2A181J2ppA03p
RPE5C2A181J2ppA03p
RPE5C2A221J2ppA03p
RPE5C2A221J2ppA03p
RPE5C2A271J2ppA03p
RPE5C2A271J2ppA03p
RPE5C2A331J2ppA03p
RPE5C2A331J2ppA03p
RPE5C2A391J2ppA03p
RPE5C2A391J2ppA03p
RPE5C2A471J2ppA03p
RPE5C2A471J2ppA03p
RPE5C2A561J2ppA03p
RPE5C2A561J2ppA03p
RPE5C2A681J2ppA03p
RPE5C2A681J2ppA03p
RPE5C2A821J2ppA03p
RPE5C2A821J2ppA03p
RPE5C2A102J2ppA03p
RPE5C2A102J2ppA03p
RPE5C2A122J2ppA03p
RPE5C2A122J2ppA03p
RPE5C2A152J2ppA03p
RPE5C2A152J2ppA03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
15 ±5%
15 ±5%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
18 ±5%
18 ±5%
22 ±5%
22 ±5%
27 ±5%
27 ±5%
33 ±5%
33 ±5%
39 ±5%
39 ±5%
47 ±5%
47 ±5%
56 ±5%
56 ±5%
68 ±5%
68 ±5%
82 ±5%
82 ±5%
100 ±5%
100 ±5%
120 ±5%
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
330 ±5%
330 ±5%
390 ±5%
390 ±5%
470 ±5%
470 ±5%
560 ±5%
560 ±5%
680 ±5%
680 ±5%
820 ±5%
820 ±5%
1000 ±5%
1000 ±5%
1200 ±5%
1200 ±5%
1500 ±5%
1500 ±5%
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
8
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
1
High Dielectric Constant Type, X7R Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RPER71E474K2ppA03p
RPER71E684K2ppC03p
RPER71E105K2ppC03p
RPER71E155K3ppC07p
RPER71E225K3ppC07p
RPER71H221K2ppA03p
RPER71H221K2ppA03p
RPER71H331K2ppA03p
RPER71H331K2ppA03p
RPER71H471K2ppA03p
RPER71H471K2ppA03p
RPER71H681K2ppA03p
RPER71H681K2ppA03p
RPER71H102K2ppA03p
RPER71H102K2ppA03p
RPER71H152K2ppA03p
RPER71H152K2ppA03p
RPER71H222K2ppA03p
RPER71H222K2ppA03p
RPER71H332K2ppA03p
RPER71H332K2ppA03p
RPER71H472K2ppA03p
RPER71H472K2ppA03p
RPER71H682K2ppA03p
RPER71H682K2ppA03p
RPER71H103K2ppA03p
RPER71H103K2ppA03p
RPER71H153K2ppA03p
RPER71H153K2ppA03p
RPER71H223K2ppA03p
RPER71H223K2ppA03p
RPER71H333K2ppA03p
RPER71H333K2ppA03p
RPER71H473K2ppA03p
RPER71H473K2ppA03p
RPER71H683K2ppA03p
RPER71H683K2ppA03p
RPER71H104K2ppA03p
RPER71H104K2ppA03p
RPER71H154K2ppC03p
RPER71H154K2ppC03p
RPER71H224K2ppC03p
RPER71H224K2ppC03p
RPER71H334K2ppC03p
RPER71H334K2ppC03p
RPER71H474K2ppC03p
RPER71H474K2ppC03p
RPER71H684K3ppC03p
RPER71H684K3ppC03p
RPER71H105K3ppC07p
RPER71H105K3ppC07p
RPER71H155K8ppC03p
RPER71H225K8ppC03p
RPER71H335K5ppC03p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
25
25
25
25
25
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
0.47µF ±10%
0.68µF ±10%
1.0µF ±10%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 4.5
5.0 x 4.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 4.5
5.0 x 4.5
5.0 x 4.5
5.0 x 4.5
7.5 x 5.5
7.5 x 5.5
7.5 x 7.5
3.15
3.15
3.15
3.15
3.15
2.5
5.0
5.0
5.0
5.0
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
5.0
5.0
K1
K1
K1
K1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
K1
K1
B1
M1
M1
M1
M1
M1
S1
M2
M2
M2
M2
M2
S2
1.5µF ±10%
2.2µF ±10%
220pF ±10%
220pF ±10%
330pF ±10%
330pF ±10%
470pF ±10%
470pF ±10%
680pF ±10%
680pF ±10%
1000pF ±10%
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4700pF ±10%
6800pF ±10%
6800pF ±10%
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
0.10µF ±10%
0.15µF ±10%
0.15µF ±10%
0.22µF ±10%
0.22µF ±10%
0.33µF ±10%
0.33µF ±10%
0.47µF ±10%
0.47µF ±10%
0.68µF ±10%
0.68µF ±10%
1.0µF ±10%
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
2.5
M1
S1
M2
S2
M1
S1
M2
S2
M1
S1
M2
S2
M1
S1
M2
S2
M1
S1
M2
S2
M1
S1
M2
S2
2.5
M1
S1
M2
S2
3.15
3.15
3.15
3.15
3.15
3.15
4.0
M1
S1
M2
S2
M1
S1
M2
S2
1.0µF ±10%
M1
M1
M1
E1
M2
M2
M2
E2
1.5µF ±10%
2.2µF ±10%
4.0
3.3µF ±10%
5.0
Continued on the following page.
9
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
1
(mm)
(mm)
Taping (1)
RPER71H475K5ppC03p
RPER72A221K2ppB03p
RPER72A221K2ppB03p
RPER72A331K2ppB03p
RPER72A331K2ppB03p
RPER72A471K2ppB03p
RPER72A471K2ppB03p
RPER72A681K2ppB03p
RPER72A681K2ppB03p
RPER72A102K2ppA03p
RPER72A102K2ppA03p
RPER72A152K2ppA03p
RPER72A152K2ppA03p
RPER72A222K2ppA03p
RPER72A222K2ppA03p
RPER72A332K2ppA03p
RPER72A332K2ppA03p
RPER72A472K2ppA03p
RPER72A472K2ppA03p
RPER72A682K2ppA03p
RPER72A682K2ppA03p
RPER72A103K2ppA03p
RPER72A103K2ppA03p
RPER72A153K2ppA03p
RPER72A153K2ppA03p
RPER72A223K2ppA03p
RPER72A223K2ppA03p
RPER72A333K2ppC03p
RPER72A333K2ppC03p
RPER72A473K2ppC03p
RPER72A473K2ppC03p
RPER72A683K3ppC07p
RPER72A683K3ppC07p
RPER72A104K3ppC07p
RPER72A104K3ppC07p
RPER72A154K8ppC03p
RPER72A224K8ppC03p
RPER72A334K5ppC03p
RPER72A474K8ppC03p
RPER72A684K6ppF14p
RPER72A105K5ppC03p
RPER72A155K7ppF03p
RPER72A225K7ppF03p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
4.7µF ±10%
220pF ±10%
220pF ±10%
330pF ±10%
330pF ±10%
470pF ±10%
470pF ±10%
680pF ±10%
680pF ±10%
1000pF ±10%
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4700pF ±10%
6800pF ±10%
6800pF ±10%
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
0.33µF ±10%
0.47µF ±10%
0.68µF ±10%
1.0µF ±10%
7.5 x 7.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 4.5
5.0 x 4.5
5.0 x 4.5
5.0 x 4.5
7.5 x 5.5
7.5 x 5.5
7.5 x 7.5
7.5 x 5.5
10.0 x 10.0
7.5 x 7.5
12.5 x 12.5
12.5 x 12.5
4.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
10.0
10.0
B1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
K1
K1
B1
K1
B1
B1
C1
C1
E1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
M1
M1
E1
M1
E1
E1
-
E2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
S2
M2
M2
M2
E2
M2
E2
E2
-
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
4.0
4.0
4.0
4.0
4.0
4.0
1.5µF ±10%
5.0
2.2µF ±10%
5.0
-
-
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
High Dielectric Constant Type, Y5V Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RPEF51H102Z2ppA03p
RPEF51H102Z2ppA03p
RPEF51H222Z2ppA03p
RPEF51H222Z2ppA03p
RPEF51H472Z2ppA03p
RPEF51H472Z2ppA03p
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
50
50
50
50
50
50
1000pF +80/-20%
1000pF +80/-20%
2200pF +80/-20%
2200pF +80/-20%
4700pF +80/-20%
4700pF +80/-20%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
P1
K1
P1
K1
P1
K1
S1
M1
S1
S2
M2
S2
M1
S1
M2
S2
M1
M2
Continued on the following page.
10
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
1
(mm)
(mm)
Taping (1)
RPEF51H103Z2ppA03p
RPEF51H103Z2ppA03p
RPEF51H223Z2ppA03p
RPEF51H223Z2ppA03p
RPEF51H473Z2ppA03p
RPEF51H473Z2ppA03p
RPEF51H104Z2ppA03p
RPEF51H104Z2ppA03p
RPEF51H224Z2ppA03p
RPEF51H224Z2ppA03p
RPEF51H474Z2ppC03p
RPEF51H474Z2ppC03p
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
50
50
50
50
50
50
50
50
50
50
50
50
10000pF +80/-20% 5.0 x 3.5
10000pF +80/-20% 5.0 x 3.5
22000pF +80/-20% 5.0 x 3.5
22000pF +80/-20% 5.0 x 3.5
47000pF +80/-20% 5.0 x 3.5
47000pF +80/-20% 5.0 x 3.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
S1
M1
S1
S2
M2
S2
2.5
2.5
M1
S1
M2
S2
2.5
2.5
M1
S1
M2
S2
0.10µF +80/-20%
0.10µF +80/-20%
0.22µF +80/-20%
0.22µF +80/-20%
0.47µF +80/-20%
0.47µF +80/-20%
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
M1
S1
M2
S2
3.15
3.15
3.15
3.15
M1
S1
M2
S2
M1
M2
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
11
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
1
Specifications
No.
1
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
Operating Temperature
Range
Char. X7R : -55 to +125˚C
-55 to +125˚C
–
Char. Y5V : -30 to +85˚C
The rated voltage is defined as the maximum voltage
that may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, VP-P
or V0-P, whichever is larger, should be maintained
within the rated voltage range.
2
Rated Voltage
See previous pages
3
4
Appearance
No defects or abnormalities
See previous pages
Visual inspection
Dimension and Marking
Visual inspection, Vernier Caliper
The capacitors should not be damaged when DC
voltages of 300%* of the rated voltage are applied
between the terminals for 1 to 5 sec.
(Charge/Discharge current V 50mA)
*250% for char. X7R, Y5V
Between
Terminals
No defects or abnormalities
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuited, is kept
Dielectric
Strength
5
approximately 2mm from the balls
as shown in the figure, and 250%
of the rated DC voltage is
Body
Insulation
Approx. 2mm
No defects or abnormalities
impressed for 1 to 5 sec. between
capacitor terminals and metal
balls. (Charge/Discharge current
Metal balls
V 50mA)
The insulation resistance should be measured with a
DC voltage not exceeding the rated voltage at normal
temperature and humidity and within 2 min. of charging.
(Charge/Discharge current V 50mA)
C V 0.047µF : 10,000MΩ min.
C G 0.047µF : 500MΩ • µF min.
C : Nominal capacitance
Insulation
Resistance
Between
Terminals
6
7
Capacitance
Within the specified tolerance
The capacitance, Q/D.F. should be measured at 25˚C
at the frequency and voltage shown in the table.
Capacitance
1000pF and
below
more than
1000pF
30pF min. : Q U 1,000
Q/Dissipation Factor (D.F.) 30pF max. : Q U 400+20C
Char. X7R : 0.025 max.
Char. Y5V : 0.05 max.
Item
Frequency
Voltage
8
C : Nominal capacitance (pF)
1±0.1MHz
1±0.1kHz
AC0.5 to 5V
(r.m.s.)
AC1±0.2V
(r.m.s.)
The capacitance change should be measured after 5
min. at each specified temperature stage.
(1) Temperature Compensating Type
Capacitance Within the specified tolerance
Within the specified tolerance
(Table B on last column)
The temperature coefficient is determined using the
capacitance measured in step 3 as a reference. When
cycling the temperature sequentially from step 1
through 5 (-55 to +125˚C) the capacitance should be
within the specified tolerance for the temperature
coefficient and capacitance change as shown in Table
A. The capacitance drift is calculated by dividing the
differences between the maximum and minimum
measured values in step 1, 3 and 5 by the cap. value in
step 3.
Change
(Table A on last column)
Capacitance
Temperature Temperature Within the specified tolerance
Characteristics Coefficient (Table A on last column)
9
Step
Temperature (°C)
25±2
1
2
3
4
5
-55±3
25±2
125±3
25±2
Capacitance Within ±0.2% or ±0.05pF,
Drift whichever is larger
(2) High Dielectric Constant Type
The ranges of capacitance change compared with the
25˚C value over the temperature ranges as shown in
Table B should be within the specified ranges.
Continued on the following page.
12
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
1
Continued from the preceding page.
Specifications
No.
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10±1 sec.
Tensile
Strength
Termination not to be broken or loosened
Terminal
Strength
10
F
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
30pF min. : Q U 1,000
The capacitor is soldered securely to a supporting
terminal and a 10 to 55Hz vibration of 1.5mm peak-
peak amplitude is applied for 6 hrs. total, 2 hrs. in each
mutually perpendicular direction. Allow 1 min. to cycle
the frequency from 10Hz to 55Hz and the converse.
Vibration
Resistance
11
Char. X7R : 0.025 max.
Char. Y5V : 0.05 max.
Q/D.F.
30pF max. : Q U 400+20C
C : Nominal capacitance (pF)
The terminal of a capacitor is dipped into a 25% ethanol
(JIS-K-8101) solution of rosin (JIS-K-5902) and
then into molten solder for 2±0.5 sec. In both cases the
depth of dipping is up to about 1.5mm to 2mm from the
terminal body.
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
12 Solderability of Leads
Temp. of solder: 245±5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235±5˚C H60A or H63A Eutectic Solder
Appearance No defects or abnormalities
Capacitance Within ±2.5% or ±0.25pF
The lead wire is immersed in the melted solder 1.5mm
to 2mm from the main body at 350±10˚C for 3.5±0.5
sec. The specified items are measured after 24±2 hrs.
(temperature compensating type) or 48±4 hrs. (high
dielectric type).
Char. X7R : Within ±7.5%
Char. Y5V : Within ±20%
Change
(whichever is larger)
Resistance
to
Soldering
Heat
13
Dielectric
Strength
(Between
Terminals)
• Initial measurement for high dielectric constant type
+ 0
No defects
The capacitors are heat treated for 1 hr. at 150
˚C,
–10
allowed to set at room temperature for 48±4 hrs., and
given an initial measurement.
Appearance No defects or abnormalities
Capacitance Within ±5% or ±0.5pF
First, repeat the following temperature/time cycle 5
times:
Char. X7R : Within ±12.5%
Char. Y5V : Within ±30%
lowest operating temperature ±3˚C/30±3 min.
ordinary temperature/3 min. max.
Change
(whichever is larger)
30pF min. : Q U 350
highest operating temperature ±3˚C/30±3 min.
ordinary temperature/3 min. max.
Next, repeat twice the successive cycles of immersion,
10pF to 30pF : Q U 275+5C/2
10pF max. : Q U 200+10C
C : Nominal capacitance (pF)
Char. X7R : 0.05 max.
Char. Y5V : 0.075 max.
Q/D.F.
each cycle consisting of immersion in a fresh water at
+5
Temperature
and
Immersion
Cycle
65 ˚C for 15 min. and immersion in a saturated
–0
Insulation
1,000MΩ or 50MΩ • µF min.
Resistance (whichever is smaller)
14
aqueous solution of salt at 0±3˚C for 15 min.
The capacitor is then promptly washed in running
water, dried with a drying cloth, and allowed to sit at
room temperature for 24±2 hrs. (temperature
compensating type) or 48±4 hrs. (high dielectric type).
Dielectric
Strength
(Between
No defects or abnormalities
• Initial measurement for high dielectric constant type
Terminals)
The capacitors are heat treated for 1 hr. at
+ 0
–10
150
˚C, allowed to sit at room temperature for 48
±4 hrs., and given an initial measurement.
Continued on the following page.
13
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
1
Continued from the preceding page.
Specifications
Temperature Compensating Type High Dielectric Constant Type
Appearance No defects or abnormalities
Capacitance Within ±5% or ±0.5pF
No.
Item
Test Method
Char. X7R : Within ±12.5%
Char. Y5V : Within ±30%
+24
– 0
Change
(whichever is larger)
Set the capacitor for 500
hrs. at 40±2˚C in 90 to
Humidity
15 (Steady
State)
95% humidity. Remove and set for 24±2 hrs.
(temperature compensating type) and 48±4 hrs. (high
dielectric constant type) at room temperature, then
measure.
30pF min. : Q U 350
10pF to 30pF : Q U 275+5C/2
10pF max. : Q U 200+10C
C : Nominal capacitance (pF)
Char. X7R : 0.05 max.
Char. Y5V : 0.075 max.
Q/D.F.
Insulation
1,000MΩ or 50MΩ • µF min.
Resistance (whichever is smaller)
Appearance No defects or abnormalities
Capacitance Within ±7.5% or ±0.75pF
+24
– 0
Char. X7R : Within ±12.5%
Char. Y5V : Within ±30%
Apply the rated voltage for 500
hrs. at 40±2˚C and
Change
(whichever is larger)
in 90 to 95% humidity. Remove and set for 24±2 hrs.
(temperature compensating type) and 48±4 hrs. (high
dielectric constant type) at room temperature, then
measure.
Humidity
Load
30pF min. : Q U 200
16
Char. X7R : 0.05 max.
Char. Y5V : 0.075 max.
Q/D.F.
30pF max. : Q U 100+10C/3
C : Nominal capacitance (pF)
(Charge/Discharge current V 50mA)
Insulation
500MΩ or 25MΩ • µF min.
Resistance (whichever is smaller)
Appearance No defects or abnormalities
Capacitance Within ±3% or ±0.3pF
+48
– 0
Apply 200% of the rated voltage for 1000
hrs. at
the maximum operating temperature. Remove and set
for 24±2 hrs. (temperature compensating type) and 48
±4 hrs. (high dielectric constant type) at room
temperature, then measure.
Char. X7R : Within ±12.5%
Char. Y5V : Within ±30%
Change
(whichever is larger)
30pF min. : Q U 350
High
17 Temperature
Load
10pF to 30pF : Q U 275+5C/2
10pF max. : Q U 200+10C
C : Nominal capacitance (pF)
Char. X7R : 0.04 max.
Char. Y5V : 0.075 max.
(Charge/Discharge current V 50mA)
Q/D.F.
• Initial measurement for high dielectric constant type
A voltage treatment should be given to the capacitor in
which a DC voltage of 200% of the rated voltage is
applied for 1 hr. at the maximum operating temperature
±3˚C. Then set for 48±4 hrs. at room temperature and
conduct initial measurement.
Insulation
1,000MΩ or 50MΩ • µF min.
Resistance (whichever is smaller)
Appearance No defects or abnormalities
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25˚C for 30±5 sec. and then removed
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent:
Solvent
18
Resistance
Marking
Legible
• Isopropyl alcohol
Table A
Table B
Capacitance Change from 25˚C (% )
Char.
X7R
Y5V
Temp. Range
-55 to +125˚C
-30 to + 85˚C
Reference Temp.
Cap. Change Rate
Nominal Values
(ppm/˚C) *1
Char.
-55˚C
-30˚C
-10˚C
Within ± 15%
25˚C
+22
Max.
0.58
Min.
-0.24
Max.
0.40
Min.
-0.17
Max.
0.25
Min.
Within –82
%
C0G
0±30
-0.11
*1: Nominal values denote the temperature coefficient within a range of
25 to 125˚C
14
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Radial Lead Type Monolithic Ceramic Capacitors
RPE Series Small Size, Large Capacitance (DC50V)
L max.
T max.
■ Features
2
1. The RPE series capacitors have small dimensions,
large capacitance, and a capacity volume ratio of
10 micro F/cm cubed, close to that of electrolytic
capacitors. They do not have polarity.
2. Excellent frequency characteristics and due to
their small internal inductance are suitable for
high frequencies.
ød : 0.5±0.05
F±0.8
3. They are not coated with wax so there is no change
in their exterior appearance due to the outflow of
wax during soldering or solvent during cleansing.
4. They are highly nonflammable, having characteristics
equivalent to the UL94V-0 standard.
Dimensions code: 2/3
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
(in mm)
Solder Coated CP Wire
L max.
T max.
5. We design capacitors in much more compact size than
current RPE Series, having reduced the diameter
by 70% max.
ød : 0.5±0.05
F±0.8
Dimensions code: W
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
(in mm)
Solder Coated CP Wire
■ Dimensions
Dimensions (mm)
Dimensions and
Lead Style Code
L
W
W1
6.0
T
F
d
2K1/2M1
3K1/3M1
WK1/WM1
5.5
5.5
5.5
4.0
5.0
7.5
5.0
5.0
5.0
0.5
0.5
0.5
Depends on
Part Number
List
7.5
10.0
Continued on the following page.
15
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
■ Marking
Rated Voltage
Temp. Char.
DC50V
X7R
Dimensions
Code
225
MK5C
2
3
2
M
475
K5C
M
106
W
M5C
Temperature Characteristics
Nominal Capacitance
Capacitance Tolerance
Rated Voltage
Marked with code (X7R char.: C)
Marked with 3 figures
Marked with code
Marked with code (DC50V: 5)
M
Marked with
Manufacturer's Identification
High Dielectric Constant Type, X7R Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
Part Number
LxW
T
Code
Bulk
Code
(µF)
(mm)
(mm)
Taping (1)
RPER71H105K2ppC60p
RPER71H155K2ppC60p
RPER71H225K2ppC60p
RPER71H335K3ppC60p
RPER71H475K3ppC60p
X7R
X7R
X7R
X7R
X7R
50
50
50
50
50
50
1.0 ±10%
1.5 ±10%
2.2 ±10%
3.3 ±10%
4.7 ±10%
10 ±20%
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
5.5 x 7.5
3.15
3.15
3.15
4.0
5.0
5.0
5.0
5.0
5.0
5.0
K1
K1
K1
K1
K1
K1
M1
M1
M1
M1
M1
M1
-
-
-
-
-
-
4.0
RPER71H106MWppC60p X7R
4.0
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
16
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
No.
1
Item
Specifications
Test Method
Operating Temperature
Range
-55 to +125˚C
–
2
3
Appearance
No defects or abnormalities
See previous pages
Visual inspection
2
Dimension and Marking
Visual inspection, Vernier Caliper
The capacitor should not be damaged when DC
voltage of 250% of the rated voltage is applied
between the terminations for 1 to 5 sec.
(Charge/Discharge current V 50mA)
Between
Terminals
No defects or abnormalities
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuit, is kept approximately
2mm from the balls as shown in
the figure, and 250% of the rated
DC voltage is impressed for 1 to 5
sec. between capacitor terminals
and metal balls.
Dielectric
Strength
4
Body
Insulation
Approx. 2mm
No defects or abnormalities
Metal balls
(Charge/Discharge current
V 50mA)
The insulation resistance should be measured with a
DC voltage not exceeding the rated voltage at normal
temperature and humidity and within 2 min. of
charging.
Insulation
Resistance
Between
Terminals
5
500MΩ · µF min.
(Charge/Discharge current V 50mA)
The capacitance/D.F. should be measured at the
frequency of 1T0.1kHz and a voltage of
AC1T0.2V(r.m.s.)
6
7
Capacitance
Within the specified tolerance
0.025 max.
Dissipation Factor (D.F.)
The capacitance change should be measured after
5 min. at each specified temperature stage.
Step
Temperature (˚C)
25T2
Capacitance
Temperature
Characteristics
1
2
3
4
5
8
Within T15%
-55T3
25T2
125T3
25T2
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10T1 sec.
Tensile
Strength
Termination not to be broken or loosened
Terminal
Strength
9
F
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
Appearance
No defects or abnormalities
Within the specified tolerance
The capacitor should be firmly soldered to the
supporting lead wire and vibrated at a frequency range
of 10 to 55Hz, 1.5mm in total amplitude, with about a 1
minute rate of vibration change from 10Hz to 55Hz and
back to 10Hz. Apply for a total of 6 hrs., 2 hrs. each in 3
mutually perpendicular directions.
Capacitance
Vibration
Resistance
D.F.
10
0.025 max.
Continued on the following page.
17
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Test Method
The terminal of a capacitor is dipped into a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin
in weight proportion) and then into molten solder (JIS-
Z-3282) for 2T0.5 sec. In both cases the depth of
dipping is up to about 1.5 to 2mm from the terminal
body.
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
11 Solderability of Leads
2
Temp. of solder: 245T5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5˚C H60A or H63A Eutectic Solder
Appearance
No defects or abnormalities
The lead wire is immersed in the melted solder 1.5 to
2mm from the main body at 350T10˚C for 3.5T0.5 sec.
The specified items are measured after 48T4 hrs.
Capacitance
Change
Resistance
to
Soldering
Heat
Within T7.5%
12
Dielectric
Strength
(Between
Terminals)
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 48T4 hrs.
No defects
Appearance
No defects or abnormalities
Within T12.5%
Capacitance
Change
The capacitor should be subjected to 200 temperature
cycles. (5 temperature cycles for dimensions code W)
D.F.
0.05 max.
Step
Temperature (˚C)
-55T3
Room Temp.
125T3
Time (min)
30T3
3 max.
30T3
Temperature
Cycle
13
Insulation
Resistance
1
2
3
4
50MΩ · µF min.
Dielectric
Strength
(Between
Terminals)
Room Temp.
3 max.
No defects or abnormalities
Appearance
No defects or abnormalities
Within T12.5%
Capacitance
Change
Humidity
14 (Steady
State)
Set the capacitor at 40T2˚C and relative humidity of 90
W24
Y 0
to 95% for 500
hrs. Remove and set for 48T4 hrs.
D.F.
0.05 max.
at room temperature, then measure.
Insulation
Resistance
50MΩ · µF min.
No defects or abnormalities
Within T12.5%
Appearance
Capacitance
Change
Apply the rated voltage at 40T2˚C and relative humidity
W24
Y 0
Humidity
Load
of 90 to 95% for 500
hrs. Remove and set for
15
48T4 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
D.F.
0.05 max.
Insulation
Resistance
50MΩ · µF min.
No defects or abnormalities
Within T12.5%
Appearance
Apply a DC voltage of 150% of the rated voltage for
W48
Y 0
1000
hrs. at the maximum operating temperature.
Capacitance
Change
Remove and set for 48T4 hrs. at room temperature,
then measure.
High
16 Temperature D.F.
Load
0.04 max.
(Charge/Discharge current V 50mA)
• Pretreatment
Apply test voltage for 1 hr., at test temperature. Remove
and set for 48T4 hrs. at room temperature.
Insulation
Resistance
50MΩ · µF min.
Appearance
No defects or abnormalities
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25 ˚C for 30T5 sec. and then removed
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent :
Solvent
Resistance
17
Marking
Legible
• Isopropyl alcohol
18
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Radial Lead Type Monolithic Ceramic Capacitors
RH Series 150°C max. (for Automotive) (DC50V-DC100V)
L max.
T max.
■ Features
1. Small size and large capacitance
2. Low ESR and ESL suitable for high frequency
3. Applied maximum temperature up to 150 deg. C
Note: Maximum accumulative time to 150 deg. C
is within 2000 hours.
ød : 0.5±0.05
4. Coated with epoxy (LxW=4.0x3.5mm) or
silicone (LxW=4.0x3.5mm over) resin which is
suitable for heat cycle.
3
F±0.8
Dimensions code: 1
Lead style code: A2
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
5. The RH series meet AEC-Q200 requirements.
(in mm)
L max.
L max.
T max.
T max.
ød : 0.5±0.05
ød : 0.5±0.05
F±0.8
F±0.8
Dimensions code: 2
Lead style code: A2
Dimensions code: 3
Lead style code: A2
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
(in mm)
(in mm)
L max.
T max.
L max.
T max.
ød : 0.5±0.05
ød : 0.5±0.05
F±0.8
F±0.8
Dimensions code: 1
Lead style code: K1
Dimensions code: 2
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
Coating extension does not exceed the end of the lead bend.
· Lead Wire : Solder Coated Copper Wire or
·
(in mm)
(in mm)
Solder Coated CP Wire
Solder Coated CP Wire
L max.
T max.
L max.
T max.
ød : 0.5±0.05
ød : 0.5±0.05
F±0.8
F±0.8
Dimensions code: 3
Lead style code: K1
Dimensions code: W
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
·
(in mm)
(in mm)
Solder Coated CP Wire
Solder Coated CP Wire
Continued on the following page.
19
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
■ Dimensions
Dimensions (mm)
Dimensions and
Lead Style Code
L
W
W1
-
T
F
d
1A2/1DB
1K1/1M1
2A2/2DB
2K1/2M1
3A2/3DB
3K1/3M1
WK1/WM1
4.0
4.0
5.7
5.7
6.0
6.0
6.0
3.5
3.5
4.5
4.5
5.5
5.5
8.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
0.5
0.5
0.5
0.5
0.5
0.5
0.5
5.0
-
See
the individual
product
7.0
-
specifications
7.5
10.0
3
■ Marking
Type
Temperature Compensating Type
DC50V, DC100V
X8G
High Dielectric Constant Type
DC50V DC100V
Rated Voltage
Temp. Char.
Dimensions
Code
X8L
8
102J
8
8
1
2
104K
103K
105
104
M K58
M K18
—
—
M
335
K58
3, W
—
Temperature Characteristics
Nominal Capacitance
Marked with code (X8G, X8L char.: 8)
Marked with 3 figures
Marked with code
Capacitance Tolerance
Marked with code (DC50V: 5, DC100V: 1)
A part is omitted (Please refer to the marking example.)
Rated Voltage
M
Marked with
Manufacturer's Identification
A part is omitted (Please refer to the marking example.)
Temperature Compensating Type, X8G Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RHE5G1H101J1ppA03p
RHE5G1H101J1ppA03p
RHE5G1H121J1ppA03p
RHE5G1H121J1ppA03p
RHE5G1H151J1ppA03p
RHE5G1H151J1ppA03p
RHE5G1H181J1ppA03p
RHE5G1H181J1ppA03p
RHE5G1H221J1ppA03p
RHE5G1H221J1ppA03p
RHE5G1H271J1ppA03p
RHE5G1H271J1ppA03p
RHE5G1H331J1ppA03p
RHE5G1H331J1ppA03p
RHE5G1H391J1ppA03p
RHE5G1H391J1ppA03p
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
100 ±5%
100 ±5%
120 ±5%
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
330 ±5%
330 ±5%
390 ±5%
390 ±5%
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Continued on the following page.
20
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RHE5G1H471J1ppA03p
RHE5G1H471J1ppA03p
RHE5G1H561J1ppA03p
RHE5G1H561J1ppA03p
RHE5G1H681J1ppA03p
RHE5G1H681J1ppA03p
RHE5G1H821J1ppA03p
RHE5G1H821J1ppA03p
RHE5G1H102J1ppA03p
RHE5G1H102J1ppA03p
RHE5G1H122J1ppA03p
RHE5G1H122J1ppA03p
RHE5G1H152J1ppA03p
RHE5G1H152J1ppA03p
RHE5G2A101J1ppA03p
RHE5G2A101J1ppA03p
RHE5G2A121J1ppA03p
RHE5G2A121J1ppA03p
RHE5G2A151J1ppA03p
RHE5G2A151J1ppA03p
RHE5G2A181J1ppA03p
RHE5G2A181J1ppA03p
RHE5G2A221J1ppA03p
RHE5G2A221J1ppA03p
RHE5G2A271J1ppA03p
RHE5G2A271J1ppA03p
RHE5G2A331J1ppA03p
RHE5G2A331J1ppA03p
RHE5G2A391J1ppA03p
RHE5G2A391J1ppA03p
RHE5G2A471J1ppA03p
RHE5G2A471J1ppA03p
RHE5G2A561J1ppA03p
RHE5G2A561J1ppA03p
RHE5G2A681J1ppA03p
RHE5G2A681J1ppA03p
RHE5G2A821J1ppA03p
RHE5G2A821J1ppA03p
RHE5G2A102J1ppA03p
RHE5G2A102J1ppA03p
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
X8G
50
50
470 ±5%
470 ±5%
560 ±5%
560 ±5%
680 ±5%
680 ±5%
820 ±5%
820 ±5%
1000 ±5%
1000 ±5%
1200 ±5%
1200 ±5%
1500 ±5%
1500 ±5%
100 ±5%
100 ±5%
120 ±5%
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
330 ±5%
330 ±5%
390 ±5%
390 ±5%
470 ±5%
470 ±5%
560 ±5%
560 ±5%
680 ±5%
680 ±5%
820 ±5%
820 ±5%
1000 ±5%
1000 ±5%
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50
50
50
50
50
50
50
50
50
50
3
50
50
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
High Dielectric Constant Type, X8L Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RHEL81H102K1ppA03p
RHEL81H102K1ppA03p
RHEL81H152K1ppA03p
RHEL81H152K1ppA03p
RHEL81H222K1ppA03p
RHEL81H222K1ppA03p
RHEL81H332K1ppA03p
RHEL81H332K1ppA03p
RHEL81H472K1ppA03p
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
50
50
50
50
50
50
50
50
50
1000pF ±10%
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
A2
K1
A2
K1
A2
K1
A2
K1
A2
DB
M1
DB
M1
DB
M1
DB
M1
DB
-
-
-
-
-
-
-
-
-
Continued on the following page.
21
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RHEL81H472K1ppA03p
RHEL81H682K1ppA03p
RHEL81H682K1ppA03p
RHEL81H103K1ppA03p
RHEL81H103K1ppA03p
RHEL81H153K1ppA03p
RHEL81H153K1ppA03p
RHEL81H223K1ppA03p
RHEL81H223K1ppA03p
RHEL81H333K1ppA03p
RHEL81H333K1ppA03p
RHEL81H473K1ppA03p
RHEL81H473K1ppA03p
RHEL81H683K1ppA03p
RHEL81H683K1ppA03p
RHEL81H104K1ppA03p
RHEL81H104K1ppA03p
RHDL81H154K2ppC03p
RHDL81H154K2ppC03p
RHDL81H224K2ppC03p
RHDL81H224K2ppC03p
RHDL81H334K2ppC03p
RHDL81H334K2ppC03p
RHDL81H474K2ppC03p
RHDL81H474K2ppC03p
RHDL81H684K2ppC03p
RHDL81H684K2ppC03p
RHDL81H105K2ppC03p
RHDL81H105K2ppC03p
RHDL81H155K2ppC03p
RHDL81H155K2ppC03p
RHDL81H225K3ppC03p
RHDL81H225K3ppC03p
RHDL81H335K3ppC03p
RHDL81H335K3ppC03p
RHDL81H475K3ppC03p
RHDL81H475K3ppC03p
RHDL81H106MWppC03p
RHEL82A102K1ppA03p
RHEL82A102K1ppA03p
RHEL82A152K1ppA03p
RHEL82A152K1ppA03p
RHEL82A222K1ppA03p
RHEL82A222K1ppA03p
RHEL82A332K1ppA03p
RHEL82A332K1ppA03p
RHEL82A472K1ppA03p
RHEL82A472K1ppA03p
RHEL82A682K1ppA03p
RHEL82A682K1ppA03p
RHEL82A103K1ppA03p
RHEL82A103K1ppA03p
RHEL82A153K1ppA03p
RHEL82A153K1ppA03p
RHEL82A223K1ppA03p
RHEL82A223K1ppA03p
RHDL82A333K2ppC03p
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
X8L
50
50
4700pF ±10%
6800pF ±10%
6800pF ±10%
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
0.10µF ±10%
0.15µF ±10%
0.15µF ±10%
0.22µF ±10%
0.22µF ±10%
0.33µF ±10%
0.33µF ±10%
0.47µF ±10%
0.47µF ±10%
0.68µF ±10%
0.68µF ±10%
1.0µF ±10%
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
6.0 x 5.5
6.0 x 5.5
6.0 x 5.5
6.0 x 5.5
6.0 x 5.5
6.0 x 5.5
6.0 x 8.0
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
4.0 x 3.5
5.7 x 4.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
K1
A2
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
M1
DB
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
4.5
50
50
3
50
50
50
50
50
50
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
4.5
50
1.0µF ±10%
4.5
50
1.5µF ±10%
4.5
50
1.5µF ±10%
4.5
50
2.2µF ±10%
5.0
50
2.2µF ±10%
5.0
50
3.3µF ±10%
5.0
50
3.3µF ±10%
5.0
50
4.7µF ±10%
5.0
50
4.7µF ±10%
5.0
50
10µF ±20%
5.0
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
1000pF ±10%
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4700pF ±10%
6800pF ±10%
6800pF ±10%
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.15
3.15
3.15
3.15
3.15
3.15
4.5
Continued on the following page.
22
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RHDL82A333K2ppC03p
RHDL82A473K2ppC03p
RHDL82A473K2ppC03p
RHDL82A683K2ppC03p
RHDL82A683K2ppC03p
RHDL82A104K2ppC03p
RHDL82A104K2ppC03p
X8L
X8L
X8L
X8L
X8L
X8L
X8L
100
100
100
100
100
100
100
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
5.7 x 4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
K1
A2
K1
A2
K1
A2
K1
M1
DB
M1
DB
M1
DB
M1
-
-
-
-
-
-
-
0.10µF ±10%
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
3
23
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Specifications
No.
1
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
(Char. X8G) (Char. X8L)
Operating Temperature
Range
-55 to +150˚C
–
2
3
Appearance
No defects or abnormalities
See previous pages
Visual inspection
Dimension and Marking
Visual inspection, Vernier Caliper
The capacitor should not be damaged when DC
voltage of 300% of the rated voltage (Temperature
Compensating Type) or 250% of the rated voltage
(High Dielectric Constant Type) is applied between
the terminations for 1 to 5 sec.
Between
Terminals
No defects or abnormalities
3
(Charge/Discharge current V 50mA)
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuit, is kept approximately
2mm from the balls as shown in
the figure, and 250% of the rated
DC voltage is impressed for 1 to 5
sec. between capacitor terminals
and metal balls.
Dielectric
Strength
4
Body
Insulation
Approx. 2mm
No defects or abnormalities
Metal balls
(Charge/Discharge current
V 50mA)
The insulation resistance should be measured at
25±3°C with a DC voltage not exceeding the rated
voltage at normal temperature and humidity and within
2 min. of charging.
Room
Temperature
10,000MΩ or 500MΩ· µF min. (whichever is smaller)
(Charge/Discharge current V 50mA)
Insulation
Resistance
5
The insulation resistance should be measured at
150±3°C with a DC voltage not exceeding the rated
voltage at normal temperature and humidity and within
2 min. of charging.
High
Temperature
100MΩ or 5MΩ· µF min. (whichever is smaller)
(Charge/Discharge current V 50mA)
6
7
Capacitance
Within the specified tolerance
The capacitance, Q/D.F. should be measured at 25˚C
at the frequency and voltage shown in the table.
Char.
X8G (1000pF X8G (more than
and below)
1000pF ), X8L
Q/Dissipation Factor (D.F.) QU1,000
0.025 max.
Item
Frequency
Voltage
1±0.1MHz
1±0.1kHz
AC0.5 to 5V
(r.m.s.)
AC1±0.2V
(r.m.s.)
The capacitance change should be measured after
5 min. at each specified temperature stage.
Within T15%
(Temp. Range: -55 to +125°C)
Within +15/-40%
Capacitance
Change
Within the specified tolerance
(Table A on last column)
Step
Temperature (˚C)
25T2
(Temp. Range: +125 to +150°C)
1
2
3
4
5
Temperature Within the specified tolerance
Coefficient
Capacitance
Temperature
Characteristics
-55T3
25T2
150T3
25T2
(Table A on last column)
8
Capacitance
Drift
Within T0.2% or T0.05pF
(whichever is larger)
• Pretreatment for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Continued on the following page.
24
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
Specifications
Temperature Compensating Type High Dielectric Constant Type
No.
Item
Test Method
(Char. X8G)
(Char. X8L)
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10T1 sec.
Tensile
Strength
Termination not to be broken or loosened
Terminal
Strength
9
3
F
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
The capacitor should be firmly soldered to the
supporting lead wire and vibrated at a frequency range
of 10 to 2000Hz, 1.5mm in total amplitude, with about
a 20 min. rate of vibration change from 10Hz to
2000Hz and back to 10Hz. Apply for a total of 6 hrs.,
2 hrs. each in 3 mutually perpendicular directions.
Vibration
Resistance
10
Q/D.F.
QU1,000
0.025 max.
The terminal of a capacitor is dipped into a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin
in weight proportion) and then into molten solder (JIS-
Z-3282) for 2T0.5 sec. In both cases the depth of
dipping is up to about 1.5 to 2mm from the terminal
body.
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
11 Solderability of Leads
Temp. of solder: 245T5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5˚C H60A or H63A Eutectic Solder
Appearance No defects or abnormalities
Capacitance Within T2.5% or T0.25pF
The lead wire is immersed in the melted solder 1.5 to
2mm from the main body at 270T5˚C for 3T0.5 sec.
The specified items are measured after 24T2 hrs.
Resistance
to
Within T7.5%
Change
(whichever is larger)
12
Soldering
Heat
Dielectric
Strength
• Pretreatment for high dielectric constant type
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
No defects
(Between
Terminals)
Appearance No defects or abnormalities except color change of outer coating Repeat 1000 cycles according to 4 heat treatments
listed in the following table. Remove and set for
24±2 hrs. at room temperature, then measure.
Capacitance Within T5% or T0.5pF
Within T12.5%
Change
(whichever is larger)
Step
Temperature (˚C)
-55T3
Room Temp.
150T3
Time (min)
30T3
3 max.
30T3
Q/D.F.
QU350
0.05 max.
1
2
3
4
Temperature
Cycle
13
Insulation
Resistance
1,000MΩ or 50MΩ · µF min. (whichever is smaller)
Room Temp.
3 max.
Dielectric
Strength
(Between
Terminals)
• Pretreatment for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
No defects or abnormalities
Appearance No defects or abnormalities
Capacitance Within T5% or T0.5pF
Set the capacitor at 85T2˚C and relative humidity of 85
W24
Y 0
±2% for 500
hrs. Remove and set for 24T2 hrs. at
Within T12.5%
Humidity
14 (Steady
State)
Change
(whichever is larger)
room temperature, then measure.
• Pretreatment for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Q/D.F.
QU350
0.05 max.
Insulation
Resistance
1,000MΩ or 50MΩ · µF min. (whichever is smaller)
Appearance No defects or abnormalities
Capacitance Within T5% or T0.5pF
Apply the rated voltage at 85T2˚C and relative humidity
W24
Y 0
of 85±2% for 500
hrs. Remove and set for 24T2
Within T12.5%
hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
• Pretreatment for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Change
(whichever is larger)
Humidity
Load
15
Q/D.F.
QU200
0.05 max.
Insulation
Resistance
500MΩ or 25MΩ · µF min. (whichever is smaller)
Continued on the following page.
25
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
Specifications
No.
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
(Char. X8G) (Char. X8L)
Appearance No defects or abnormalities except color change of outer coating Apply a DC voltage of 150% of the rated voltage for
W48
1000
hrs. at the maximum operating temperature.
Y 0
Capacitance Within T3% or T0.3pF
Within T12.5%
Remove and set for 24T2 hrs. at room temperature,
then measure.
Change
(whichever is larger)
High
16 Temperature Q/D.F.
Load
QU350
0.04 max.
(Charge/Discharge current V 50mA)
• Pretreatment for high dielectric constant type
Apply test voltage for 1 hr., at test temperature. Remove
and set for 24T2 hrs. at room temperature.
Insulation
Resistance
1,000MΩ or 50MΩ · µF min. (whichever is smaller)
Appearance No defects or abnormalities
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25 ˚C for 30T5 sec. and then removed
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent :
3
Solvent
Resistance
17
Marking
Legible
• Isopropyl alcohol
Table A
Capacitance Change from 25°C (% )
Nominal Values
(ppm/°C) *1
Char.
–55°C
Max. Min.
0.58 –0.24 0.40 –0.17 0.25 –0.11
–30°C
–10°C
Max. Min.
Max. Min.
X8G
0±30
*1: Nominal values denote the temperature coefficient within a range of
25 to 150°C
26
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Radial Lead Type Monolithic Ceramic Capacitors
RDE Series (For Commercial Use Only) (DC25V-DC630V)
L max.
T max.
■ Features
1. Small size and large capacitance
2. Low ESR characteristics for high frequency
3. Coated with epoxy resin whose flammability is
equivalent to UL94V-0
ød : 0.5±0.05
■ Applications
General electronic equipment
(Do not use for automotive-related power train and
safety equipment.)
F±0.8
Dimensions code: 0/1/2/3
Lead style code: P1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
·
(in mm)
Solder Coated CP Wire
L max.
T max.
L max.
T max.
4
ød : 0.5±0.05
ød : 0.5±0.05
F±0.8
F±0.8
Dimensions code: 0/1
Lead style code: K1
Dimensions code: 2/3/8
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
Coating extension does not exceed the end of the lead bend.
· Lead Wire : Solder Coated Copper Wire or
·
(in mm)
(in mm)
Solder Coated CP Wire
Solder Coated CP Wire
L max.
T max.
T max.
L max.
ød : 0.5±0.05
ød : 0.5±0.05
F±0.8
F±0.8
Dimensions code: 5
Lead style code: B1
Dimensions code: U
Lead style code: B1
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
(in mm)
(in mm)
L max.
T max.
■ Dimensions
Dimensions (mm)
Dimensions and
Lead Style Code
DC Rated
Voltage
L
W
W1
T
F
d
0P1/0S1
0K1/0M1
1P1/1S1
1K1/1M1
2P1/2S1
5.0 3.5 6.0
4.0 3.5 6.0
5.0 3.5 5.0
4.5 3.5 5.0
5.5 4.0 6.0
2.5 0.5
5.0 0.5
2.5 0.5
5.0 0.5
2.5 0.5
5.0 0.5
5.0 0.5
2.5 0.5
5.0 0.5
5.0 0.5
5.0 0.5
25V/50V/100V
25V/50V/100V
25V/50V/100V
25V/50V/100V
25V/50V/100V
ød : 0.5±0.05
See
the individual
product
25V/50V/100V 5.5 4.0 6.0
250V/630V 5.0 3.5 5.0
5.5 5.0 7.5
25V/50V/100V 5.5 5.0 7.5
250V/630V 5.0 4.5 6.3
2K1/2M1
3P1/3S1
3K1/3M1
25V/50V/100V
specifications
F±0.8
Dimensions code: W
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
5B1/5E1
8K1/8M1
7.5 7.5*
250V/630V 7.5 5.5 8.0
-
250V/630V
·
(in mm)
Solder Coated CP Wire
5.0
0.5
UB1/UE1
WK1/WM1
*DC630V: W+0.5mm
7.7 12.5*
-
5.0 0.5
5.0 0.5
250V/630V
25V/100V
5.5 7.5 10.0
Continued on the following page.
27
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
■ Marking
Temperature
Compensating
Type
Type
High Dielectric Constant Type
DC50V
DC50V,
DC100V
Rated Voltage
Temp. Char.
DC25V
X7R
DC100V
DC250V DC630V
X7R
Dimensions
Code
C0G
X7S
X7S
X7R
F
Y5V
X7S
X7R
A
102J
104K
473
103Z
0
1
–
–
–
–
–
–
–
224K
224K
224K
–
–
–
–
–
–
–
–
–
Individual
Specification
Code
103K
475
475
105
105
App
MK2C
MK5C
MK5C
MK1C
2
–
–
Individual
Specification
Code
153
153
MK4C
MK7C
Cpp
M
M
M
M
M
226
335
225
104
104
3, 8, W
5, U
–
–
–
–
–
–
–
–
–
–
–
–
K2C
K5C
K1C
K4C
K7C
4
M
M
474
474
–
–
–
K4C
M7C
Marked with code (C0G char.: A, X7S/X7R char.: C, F/Y5V char.: F)
A part is omitted (Please refer to the marking example.)
Temperature Characteristics
Nominal Capacitance
Under 100pF: Actual value 100pF and over: Marked with 3 figures
Marked with code
A part is omitted (Please refer to the marking example.)
Capacitance Tolerance
Marked with code (DC25V: 2, DC50V: 5, DC100V: 1, DC250V: 4, DC630V: 7)
Lower horizontal line for F char.
Rated Voltage
A part is omitted (Please refer to the marking example.)
M
Marked with
Manufacturer's Identification
A part is omitted (Please refer to the marking example.)
Temperature Compensating Type, C0G Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDE5C1H100J0ppC03p
RDE5C1H100J0ppC03p
RDE5C1H120J0ppC03p
RDE5C1H120J0ppC03p
RDE5C1H150J0ppC03p
RDE5C1H150J0ppC03p
RDE5C1H180J0ppC03p
RDE5C1H180J0ppC03p
RDE5C1H220J0ppC03p
RDE5C1H220J0ppC03p
RDE5C1H270J0ppC03p
RDE5C1H270J0ppC03p
RDE5C1H330J0ppC03p
RDE5C1H330J0ppC03p
RDE5C1H390J0ppC03p
RDE5C1H390J0ppC03p
RDE5C1H470J0ppC03p
RDE5C1H470J0ppC03p
RDE5C1H560J0ppC03p
RDE5C1H560J0ppC03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
10 ±5%
10 ±5%
12 ±5%
12 ±5%
15 ±5%
15 ±5%
18 ±5%
18 ±5%
22 ±5%
22 ±5%
27 ±5%
27 ±5%
33 ±5%
33 ±5%
39 ±5%
39 ±5%
47 ±5%
47 ±5%
56 ±5%
56 ±5%
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Continued on the following page.
28
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDE5C1H680J0ppC03p
RDE5C1H680J0ppC03p
RDE5C1H820J0ppC03p
RDE5C1H820J0ppC03p
RDE5C1H101J0ppC03p
RDE5C1H101J0ppC03p
RDE5C1H121J0ppC03p
RDE5C1H121J0ppC03p
RDE5C1H151J0ppC03p
RDE5C1H151J0ppC03p
RDE5C1H181J0ppC03p
RDE5C1H181J0ppC03p
RDE5C1H221J0ppC03p
RDE5C1H221J0ppC03p
RDE5C1H271J0ppC03p
RDE5C1H271J0ppC03p
RDE5C1H331J0ppC03p
RDE5C1H331J0ppC03p
RDE5C1H391J0ppC03p
RDE5C1H391J0ppC03p
RDE5C1H471J0ppC03p
RDE5C1H471J0ppC03p
RDE5C1H561J0ppC03p
RDE5C1H561J0ppC03p
RDE5C1H681J0ppC03p
RDE5C1H681J0ppC03p
RDE5C1H821J0ppC03p
RDE5C1H821J0ppC03p
RDE5C1H102J0ppC03p
RDE5C1H102J0ppC03p
RDE5C2A100J0ppC03p
RDE5C2A100J0ppC03p
RDE5C2A120J0ppC03p
RDE5C2A120J0ppC03p
RDE5C2A150J0ppC03p
RDE5C2A150J0ppC03p
RDE5C2A180J0ppC03p
RDE5C2A180J0ppC03p
RDE5C2A220J0ppC03p
RDE5C2A220J0ppC03p
RDE5C2A270J0ppC03p
RDE5C2A270J0ppC03p
RDE5C2A330J0ppC03p
RDE5C2A330J0ppC03p
RDE5C2A390J0ppC03p
RDE5C2A390J0ppC03p
RDE5C2A470J0ppC03p
RDE5C2A470J0ppC03p
RDE5C2A560J0ppC03p
RDE5C2A560J0ppC03p
RDE5C2A680J0ppC03p
RDE5C2A680J0ppC03p
RDE5C2A820J0ppC03p
RDE5C2A820J0ppC03p
RDE5C2A101J0ppC03p
RDE5C2A101J0ppC03p
RDE5C2A121J0ppC03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
50
50
68 ±5%
68 ±5%
82 ±5%
82 ±5%
100 ±5%
100 ±5%
120 ±5%
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
330 ±5%
330 ±5%
390 ±5%
390 ±5%
470 ±5%
470 ±5%
560 ±5%
560 ±5%
680 ±5%
680 ±5%
820 ±5%
820 ±5%
1000 ±5%
1000 ±5%
10 ±5%
10 ±5%
12 ±5%
12 ±5%
15 ±5%
15 ±5%
18 ±5%
18 ±5%
22 ±5%
22 ±5%
27 ±5%
27 ±5%
33 ±5%
33 ±5%
39 ±5%
39 ±5%
47 ±5%
47 ±5%
56 ±5%
56 ±5%
68 ±5%
68 ±5%
82 ±5%
82 ±5%
100 ±5%
100 ±5%
120 ±5%
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
50
50
50
50
50
50
50
50
50
50
50
50
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Continued on the following page.
29
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Capacitance
(pF)
Part Number
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDE5C2A121J0ppC03p
RDE5C2A151J0ppC03p
RDE5C2A151J0ppC03p
RDE5C2A181J0ppC03p
RDE5C2A181J0ppC03p
RDE5C2A221J0ppC03p
RDE5C2A221J0ppC03p
RDE5C2A271J0ppC03p
RDE5C2A271J0ppC03p
RDE5C2A331J0ppC03p
RDE5C2A331J0ppC03p
RDE5C2A391J0ppC03p
RDE5C2A391J0ppC03p
RDE5C2A471J0ppC03p
RDE5C2A471J0ppC03p
RDE5C2A561J0ppC03p
RDE5C2A561J0ppC03p
RDE5C2A681J0ppC03p
RDE5C2A681J0ppC03p
RDE5C2A821J0ppC03p
RDE5C2A821J0ppC03p
RDE5C2A102J0ppC03p
RDE5C2A102J0ppC03p
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
C0G
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
120 ±5%
150 ±5%
150 ±5%
180 ±5%
180 ±5%
220 ±5%
220 ±5%
270 ±5%
270 ±5%
330 ±5%
330 ±5%
390 ±5%
390 ±5%
470 ±5%
470 ±5%
560 ±5%
560 ±5%
680 ±5%
680 ±5%
820 ±5%
820 ±5%
1000 ±5%
1000 ±5%
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
High Dielectric Constant Type, X7R/X7S Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDER71E104K0ppC03p
RDER71E104K0ppC03p
RDEC71E224K0ppC03p
RDEC71E224K0ppC03p
RDEC71E474K0ppC03p
RDEC71E474K0ppC03p
RDEC71E105K0ppC03p
RDEC71E105K0ppC03p
RDEC71E225K1ppC03p
RDEC71E225K1ppC03p
RDEC71E475K2ppC03p
RDEC71E475K2ppC03p
RDEC71E106K2ppC03p
RDEC71E106K2ppC03p
RDEC71E226K3ppC03p
RDEC71E226K3ppC03p
RDEC71E476MWppC03p
RDER71H221K0ppC03p
RDER71H221K0ppC03p
RDER71H331K0ppC03p
RDER71H331K0ppC03p
RDER71H471K0ppC03p
RDER71H471K0ppC03p
RDER71H681K0ppC03p
RDER71H681K0ppC03p
RDER71H102K0ppC03p
X7R
X7R
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7S
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
50
50
50
50
50
50
50
50
50
0.10µF ±10%
0.10µF ±10%
0.22µF ±10%
0.22µF ±10%
0.47µF ±10%
0.47µF ±10%
1.0µF ±10%
1.0µF ±10%
2.2µF ±10%
2.2µF ±10%
4.7µF ±10%
4.7µF ±10%
10.0µF ±10%
10.0µF ±10%
22.0µF ±10%
22.0µF ±10%
47.0µF ±20%
220pF ±10%
220pF ±10%
330pF ±10%
330pF ±10%
470pF ±10%
470pF ±10%
680pF ±10%
680pF ±10%
1000pF ±10%
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
5.5 x 7.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
2.5
5.0
2.5
5.0
2.5
5.0
5.0
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
P1
K1
P1
K1
P1
K1
K1
K1
P1
K1
P1
K1
P1
K1
P1
K1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
M1
S1
2.5
2.5
M1
S1
2.5
2.5
M1
S1
2.5
3.15
3.15
3.15
3.15
3.15
3.15
4.0
M1
S1
S1
M1
S1
M1
S1
4.0
M1
M1
M1
S1
4.0
2.5
2.5
2.5
M1
S1
2.5
2.5
M1
S1
2.5
2.5
M1
S1
2.5
2.5
M1
Continued on the following page.
30
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDER71H102K0ppC03p
RDER71H152K0ppC03p
RDER71H152K0ppC03p
RDER71H222K0ppC03p
RDER71H222K0ppC03p
RDER71H332K0ppC03p
RDER71H332K0ppC03p
RDER71H472K0ppC03p
RDER71H472K0ppC03p
RDER71H682K0ppC03p
RDER71H682K0ppC03p
RDER71H103K0ppC03p
RDER71H103K0ppC03p
RDER71H153K0ppC03p
RDER71H153K0ppC03p
RDER71H223K0ppC03p
RDER71H223K0ppC03p
RDER71H333K0ppC03p
RDER71H333K0ppC03p
RDER71H473K0ppC03p
RDER71H473K0ppC03p
RDER71H683K0ppC03p
RDER71H683K0ppC03p
RDER71H104K0ppC03p
RDER71H104K0ppC03p
RDER71H154K1ppC03p
RDER71H154K1ppC03p
RDER71H224K1ppC03p
RDER71H224K1ppC03p
RDER71H334K1ppC03p
RDER71H334K1ppC03p
RDER71H474K1ppC03p
RDER71H474K1ppC03p
RDER71H684K2ppC03p
RDER71H684K2ppC03p
RDER71H105K2ppC03p
RDER71H105K2ppC03p
RDER71H155K2ppC03p
RDER71H155K2ppC03p
RDER71H225K2ppC03p
RDER71H225K2ppC03p
RDER71H335K3ppC03p
RDER71H335K3ppC03p
RDEC71H475K2ppC03p
RDEC71H475K2ppC03p
RDER72A102K0ppC03p
RDER72A102K0ppC03p
RDER72A152K0ppC03p
RDER72A152K0ppC03p
RDER72A222K0ppC03p
RDER72A222K0ppC03p
RDER72A332K0ppC03p
RDER72A332K0ppC03p
RDER72A472K0ppC03p
RDER72A472K0ppC03p
RDER72A682K0ppC03p
RDER72A682K0ppC03p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7S
X7S
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
50
50
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4700pF ±10%
6800pF ±10%
6800pF ±10%
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
0.10µF ±10%
0.15µF ±10%
0.15µF ±10%
0.22µF ±10%
0.22µF ±10%
0.33µF ±10%
0.33µF ±10%
0.47µF ±10%
0.47µF ±10%
0.68µF ±10%
0.68µF ±10%
1.0µF ±10%
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
5.5 x 4.0
5.5 x 4.0
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
4
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
2.5
50
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
4.0
50
50
50
50
50
50
50
50
50
50
50
1.0µF ±10%
50
1.5µF ±10%
50
1.5µF ±10%
50
2.2µF ±10%
50
2.2µF ±10%
50
3.3µF ±10%
50
3.3µF ±10%
4.0
50
4.7µF ±10%
3.15
3.15
2.5
50
4.7µF ±10%
100
100
100
100
100
100
100
100
100
100
100
100
1000pF ±10%
1000pF ±10%
1500pF ±10%
1500pF ±10%
2200pF ±10%
2200pF ±10%
3300pF ±10%
3300pF ±10%
4700pF ±10%
4700pF ±10%
6800pF ±10%
6800pF ±10%
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Continued on the following page.
31
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDER72A103K0ppC03p
RDER72A103K0ppC03p
RDER72A153K0ppC03p
RDER72A153K0ppC03p
RDER72A223K0ppC03p
RDER72A223K0ppC03p
RDER72A333K1ppC03p
RDER72A333K1ppC03p
RDER72A473K1ppC03p
RDER72A473K1ppC03p
RDER72A683K1ppC03p
RDER72A683K1ppC03p
RDER72A104K1ppC03p
RDER72A104K1ppC03p
RDER72A154K2ppC03p
RDER72A154K2ppC03p
RDER72A224K1ppC03p
RDER72A224K1ppC03p
RDER72A334K1ppC03p
RDER72A334K1ppC03p
RDER72A474K1ppC03p
RDER72A474K1ppC03p
RDER72A684K2ppC03p
RDER72A684K2ppC03p
RDER72A105K2ppC03p
RDER72A105K2ppC03p
RDEC72A155K3ppC03p
RDEC72A155K3ppC03p
RDEC72A225K3ppC03p
RDEC72A225K3ppC03p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7S
X7S
X7S
X7S
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
630
630
630
630
630
630
630
630
10000pF ±10%
10000pF ±10%
15000pF ±10%
15000pF ±10%
22000pF ±10%
22000pF ±10%
33000pF ±10%
33000pF ±10%
47000pF ±10%
47000pF ±10%
68000pF ±10%
68000pF ±10%
0.10µF ±10%
0.10µF ±10%
0.15µF ±10%
0.15µF ±10%
0.22µF ±10%
0.22µF ±10%
0.33µF ±10%
0.33µF ±10%
0.47µF ±10%
0.47µF ±10%
0.68µF ±10%
0.68µF ±10%
1.0µF ±10%
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
5.5 x 4.0
5.5 x 4.0
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
4.5 x 3.5
5.0 x 3.5
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
5.5 x 5.0
5.5 x 5.0
5.5 x 7.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 4.5
5.0 x 4.5
7.5 x 5.5
7.5 x 5.5
7.5 x 7.5
7.5 x 7.5
7.7 x 12.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
5.0 x 3.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
2.5
5.0
5.0
2.5
5.0
2.5
5.0
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
P1
K1
K1
P1
K1
P1
K1
P1
P1
K1
P1
K1
P1
K1
P1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
K1
B1
B1
B1
K1
K1
K1
K1
K1
K1
K1
K1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
M1
S1
2.5
2.5
M1
S1
2.5
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
4.0
M1
S1
M1
S1
M1
S1
M1
S1
S1
M1
M1
S1
4
M1
S1
M1
S1
S1
M1
S1
1.0µF ±10%
M1
S1
1.5µF ±10%
1.5µF ±10%
4.0
M1
S1
2.2µF ±10%
4.0
2.2µF ±10%
4.0
M1
M1
M1
M1
M1
M1
M1
M1
M1
M1
M1
M1
M1
M1
B1
M1
M1
E1
RDEC72A475MWppC03p X7S
4.7µF ±20%
4.0
RDER72E102K2ppA11p
RDER72E152K2ppA11p
RDER72E222K2ppA11p
RDER72E332K2ppA11p
RDER72E472K2ppA11p
RDER72E682K2ppA11p
RDER72E103K2ppA11p
RDER72E153K2ppC11p
RDER72E223K2ppC11p
RDER72E333K2ppC11p
RDER72E473K2ppC11p
RDER72E683K3ppC11p
RDER72E104K3ppC11p
RDER72E154K8ppC11p
RDER72E224K8ppC11p
RDER72E334K5ppC13p
RDER72E474K5ppC13p
RDER72E105MUppC13p
RDER72J102K2ppC11p
RDER72J152K2ppC11p
RDER72J222K2ppC11p
RDER72J332K2ppC11p
RDER72J472K2ppC11p
RDER72J682K2ppC11p
RDER72J103K2ppC11p
RDER72J153K2ppC11p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
1000pF ±10%
1500pF ±10%
2200pF ±10%
3300pF ±10%
4700pF ±10%
6800pF ±10%
10000pF ±10%
15000pF ±10%
22000pF ±10%
33000pF ±10%
47000pF ±10%
68000pF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
0.33µF ±10%
0.47µF ±10%
1.0µF ±20%
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
4.0
4.0
E1
4.0
E1
1000pF ±10%
1500pF ±10%
2200pF ±10%
3300pF ±10%
4700pF ±10%
6800pF ±10%
10000pF ±10%
15000pF ±10%
3.15
3.15
3.15
3.15
3.15
3.15
3.15
3.15
M1
M1
M1
M1
M1
M1
M1
M1
Continued on the following page.
32
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDER72J223K3ppC11p
RDER72J333K3ppC11p
RDER72J473K3ppC11p
RDER72J683K8ppC11p
RDER72J104K8ppC11p
RDER72J154K5ppC13p
RDER72J224K5ppC13p
RDER72J474MUppC13p
X7R
X7R
X7R
X7R
X7R
X7R
X7R
X7R
630
630
630
630
630
630
630
630
22000pF ±10%
33000pF ±10%
47000pF ±10%
68000pF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
0.47µF ±20%
5.0 x 4.5
5.0 x 4.5
5.0 x 4.5
7.5 x 5.5
7.5 x 5.5
7.5 x 8.0
7.5 x 8.0
7.7 x 13.0
3.15
3.15
3.15
3.15
3.15
4.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
K1
K1
K1
K1
K1
B1
B1
B1
M1
M1
M1
M1
M1
E1
-
-
-
-
-
-
-
-
4.0
E1
4.0
E1
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
High Dielectric Constant Type, F/Y5V Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDEF11H103Z0ppC01p
RDEF11H103Z0ppC01p
RDEF51H103Z0ppC03p
RDEF51H103Z0ppC03p
RDEF11H223Z0ppC01p
RDEF11H223Z0ppC01p
RDEF51H223Z0ppC03p
RDEF51H223Z0ppC03p
RDEF11H473Z0ppC01p
RDEF11H473Z0ppC01p
RDEF51H473Z0ppC03p
RDEF51H473Z0ppC03p
RDEF11H104Z0ppC01p
RDEF11H104Z0ppC01p
RDEF51H104Z0ppC03p
RDEF51H104Z0ppC03p
F
F
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
10000pF +80/-20% 4.0 x 3.5
10000pF +80/-20% 5.0 x 3.5
10000pF +80/-20% 4.0 x 3.5
10000pF +80/-20% 5.0 x 3.5
22000pF +80/-20% 4.0 x 3.5
22000pF +80/-20% 5.0 x 3.5
22000pF +80/-20% 4.0 x 3.5
22000pF +80/-20% 5.0 x 3.5
47000pF +80/-20% 4.0 x 3.5
47000pF +80/-20% 5.0 x 3.5
47000pF +80/-20% 4.0 x 3.5
47000pF +80/-20% 5.0 x 3.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
5.0
2.5
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
K1
P1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
M1
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4
Y5V
Y5V
F
F
Y5V
Y5V
F
F
Y5V
Y5V
F
0.10µF +80/-20%
0.10µF +80/-20%
0.10µF +80/-20%
0.10µF +80/-20%
4.0 x 3.5
5.0 x 3.5
4.0 x 3.5
5.0 x 3.5
F
Y5V
Y5V
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
33
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Specifications
No.
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
Char. X7R, X7S: -55 to +125˚C
Char. F: -25 to +85˚C
Char. Y5V: -30 to +85˚C
Operating Temperature
Range
1
-55 to +125˚C
–
2
3
Appearance
No defects or abnormalities
See previous pages
Visual inspection
Dimension and Marking
Visual inspection, Vernier Caliper
The capacitors should not be damaged when test
voltages of Table are applied between the terminals
for 1 to 5 sec. (Charge/Discharge current V 50mA)
Temperature Compensating Type
Rated Voltage
DC50V, DC100V
Test Voltage
300% of the rated voltage
Between
Terminals
No defects or abnormalities
High Dielectric Constant Type
Rated Voltage
Test Voltage
DC25V, DC50V
DC100V, DC250V
DC630V
250% of the rated voltage
200% of the rated voltage
150% of the rated voltage
Dielectric
Strength
4
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuited, is kept
4
approximately 2mm from the balls
as shown in the figure, and 250%
of the rated voltage (200% of the
rated voltage in case of rated
voltage: DC100V, DC250V,
DC630V) is impressed for 1 to 5
sec. between capacitor terminals
and metal balls. (Charge/Discharge
current V 50mA)
Body
Insulation
Approx. 2mm
Metal balls
No defects or abnormalities
The insulation resistance should be measured with a
DC voltage not exceeding the rated voltage
(DC500±50V in case of rated vlotage: DC630V) at
normal temperature and humidity and within 2 min. of
charging. (Charge/Discharge current V 50mA)
Rated Voltage: DC25V, DC50V, DC100V
10,000MΩ min. or 500MΩ • µF min. whichever is smaller
Rated Voltage: DC250V, DC630V
Insulation
Resistance
Between
Terminals
5
6
10,000MΩ min. or 100MΩ • µF min. whichever is smaller
Capacitance
Within the specified tolerance
The capacitance, Q/D.F. should be measured at 25˚C
at the frequency and voltage shown in the table.
Temperature Compensating Type
Capacitance
CV1000pF
1±0.1MHz
CG1000pF
1±0.1kHz
Item
Frequency
Voltage
AC0.5 to 5V
(r.m.s.)
AC1±0.2V
(r.m.s.)
30pF min.: QU1,000
Q/Dissipation Factor (D.F.) 30pF max.: QU400+20C
Char. X7R: 0.025 max.
Char. F, Y5V: 0.05 max.
Char. X7S: 0.125 max.
7
C: Nominal capacitance (pF)
High Dielectric Constant Type
Capacitance
CV10µF
CG10µF
Item
Frequency
Voltage
1±0.1kHz
120±24Hz
AC1±0.2V
(r.m.s.)
AC0.5±0.1V
(r.m.s.)
Continued on the following page.
34
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
Specifications
Temperature Compensating Type High Dielectric Constant Type
No.
Item
Test Method
The capacitance change should be measured after 5
min. at each specified temperature stage.
(1) Temperature Compensating Type
Capacitance Within the specified tolerance
Change (Table A on last column)
Within the specified tolerance
(Table B on last column)
The temperature coefficient is determined using the
capacitance measured in step 3 as a reference. When
cycling the temperature sequentially from step 1
through 5 (-55 to +125˚C) the capacitance should be
within the specified tolerance for the temperature
coefficient and capacitance change as shown in Table
A. The capacitance drift is calculated by dividing the
differences between the maximum and minimum
measured values in step 1, 3 and 5 by the cap. value in
step 3.
Temperature Within the specified tolerance
Coefficient (Table A on last column)
Capacitance
Temperature
Characteristics
8
Step
Temperature (˚C)
25±2
1
2
3
4
5
-55±3
25±2
125±3
25±2
(2) High Dielectric Constant Type
4
The ranges of capacitance change compared with the
25˚C (Char. F: 20˚C) value over the temperature
ranges as shown in Table B should be within the
specified ranges.
Capacitance Within ±0.2% or ±0.05pF,
Drift
whichever is larger
• Pretreatment (for high dielectric constant type)
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10±1 sec.
Tensile
Strength
Termination not to be broken or loosened
Terminal
Strength
9
F
Each lead wire should be subjected to a force of 2.5N
and then bent 90° at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90° in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
30pF min.: QU1,000
The capacitor is soldered securely to a supporting
terminal and a 10 to 55Hz vibration of 1.5mm peak-
peak amplitude is applied for 6 hrs. total, 2 hrs. in each
mutually perpendicular direction. Allow 1 min. to cycle
the frequency from 10Hz to 55Hz and the converse.
Vibration
Resistance
10
Char. X7R: 0.025 max.
Char. F, Y5V: 0.05 max.
Char. X7S: 0.125 max.
Q/D.F.
30pF max.: QU400+20C
C: Nominal capacitance (pF)
The terminal of a capacitor is dipped into a 25% ethanol
(JIS-K-8101) solution of rosin (JIS-K-5902) and
then into molten solder for 2±0.5 sec. In both cases the
depth of dipping is up to about 1.5mm to 2mm from the
terminal body.
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
11 Solderability of Leads
Temp. of solder: 245±5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235±5˚C H60A or H63A Eutectic Solder
Appearance No defects or abnormalities
Capacitance Within ±2.5% or ±0.25pF
The lead wire is immersed in the melted solder 1.5mm
to 2mm from the main body at 350±10°C for 3.5±0.5
sec.
The specified items are measured after 24±2 hrs.
• Pretreatment (for high dielectric constant type)
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Char. X7R, X7S: Within ±10%
Char. F, Y5V: Within ±20%
Resistance
to
Soldering
Heat
Change
(whichever is larger)
12
Dielectric
Strength
(Between
Terminals)
No defects
Continued on the following page.
35
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
Specifications
No.
Item
Test Method
Temperature Compensating Type High Dielectric Constant Type
Appearance No defects or abnormalities
Capacitance Within ±5% or ±0.5pF
Char. X7R, X7S: Within ±12.5%
Char. F, Y5V: Within ±30%
The capacitor should be subjected to 5 temperature
cycles.
Change
(whichever is larger)
30pF min.: QU350
Remove and set for 24±2 hrs. at room temperature,
then measure.
Char. X7R: 0.05 max.
Char. F, Y5V: 0.075 max.
Char. X7S: 0.2 max.
10pF to 30pF: QU275+5C/2
10pF max.: QU200+10C
C: Nominal capacitance (pF)
Q/D.F.
Step
Temperature (˚C)
Min. Operating Temp. ±3
Room Temp.
Max. Operating Temp. ±3
Room Temp.
Time (min)
30±3
3 max.
30±3
Temperature
Cycle
1
2
3
4
13
Rated Voltage: DC25V, DC50V, DC100V
1,000MΩ, 50MΩ • µF min. (whichever is smaller)
Resistance Rated Voltage: DC250V, DC630V
1,000MΩ, 10MΩ • µF min. (whichever is smaller)
Insulation
3 max.
• Pretreatment (for high dielectric constant type)
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Dielectric
Strength
(Between
Terminals)
No defects or abnormalities
Appearance No defects or abnormalities
Capacitance Within ±5% or ±0.5pF
Char. X7R, X7S: Within ±15%
Char. F, Y5V: Within ±30%
Change
Q/D.F.
(whichever is larger)
4
Set the capacitor at 40±2°C and relative humidity of
+24
– 0
90 to 95% for 500
hrs.
30pF min.: QU350
Char. X7R: 0.05 max.
Char. F, Y5V: 0.075 max.
Char. X7S: 0.2 max.
Humidity
14 (Steady
State)
Remove and set for 24±2 hrs. at room temperature,
then measure.
• Pretreatment (for high dielectric constant type)
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
10pF to 30pF: QU275+5C/2
10pF max.: QU200+10C
C: Nominal capacitance (pF)
Rated Voltage: DC25V, DC50V, DC100V
1,000MΩ, 50MΩ • µF min. (whichever is smaller)
Insulation
Resistance Rated Voltage: DC250V, DC630V
1,000MΩ, 10MΩ • µF min. (whichever is smaller)
Appearance No defects or abnormalities
+24
– 0
Capacitance Within ±7.5% or ±0.75pF
Char. X7R, X7S: Within ±15%
Char. F, Y5V: Within ±30%
Apply the rated voltage for 500
in 90 to 95% humidity.
hrs. at 40±2°C and
Change
Q/D.F.
(whichever is larger)
Remove and set for 24±2 hrs. at room temperature,
then measure.
(Charge/Discharge current V50mA)
30pF min.: QU200
30pF max.: QU100+10C/3
C: Nominal capacitance (pF)
Char. X7R: 0.05 max.
Char. F, Y5V: 0.075 max.
Char. X7S: 0.2 max.
Humidity
Load
15
• Pretreatment (for high dielectric constant type)
Perform a heat treatment at 150+0/-10°C for 1 hr., and
then let sit at room temperature for 24±2 hrs.
Rated Voltage: DC25V, DC50V, DC100V
500MΩ or 25MΩ • µF min. (whichever is smaller)
Resistance Rated Voltage: DC250V, DC630V
1,000MΩ or 10MΩ • µF min. (whichever is smaller)
Insulation
Appearance No defects or abnormalities
+48
Capacitance Within ±3% or ±0.3pF
Char. X7R, X7S: Within ±15%
Char. F, Y5V: Within ±30%
Apply voltage in Table for 1000
hrs. at the
– 0
Change
Q/D.F.
(whichever is larger)
maximum operating temperature±3°C.
Remove and set for 24±2 hrs. at room temperature,
then measure. (Charge/Discharge current V50mA)
30pF min.: QU350
Char. X7R: 0.05 max.
Char. F, Y5V: 0.075 max.
Char. X7S: 0.2 max.
10pF to 30pF: QU275+5C/2
10pF max.: QU200+10C
C: Nominal capacitance (pF)
High
16 Temperature
Load
Rated Voltage
DC25V, DC50V
DC100V, DC250V
DC630V
Test Voltage
150% of the rated voltage
120% of the rated voltage
Rated Voltage: DC25V, DC50V, DC100V
• Pretreatment (for high dielectric constant type)
Appy test voltage for 1 hr., at test temperature.
Remove and set for 24±2 hrs. at room temperature.
Insulation
1,000MΩ, 50MΩ • µF min. (whichever is smaller)
Resistance Rated Voltage: DC250V, DC630V
1,000MΩ, 10MΩ • µF min. (whichever is smaller)
Appearance No defects or abnormalities
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25°C for 30±5 sec. and then removed
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent:
Solvent
17
Resistance
Marking
Legible
• Isopropyl alcohol
Table A
Table B
Capacitance Change from 25°C (% )
Char.
X7R
X7S
Y5V
F
Temp. Range
Reference Temp.
25°C
Cap. Change Rate
Within ±15%
Nominal Values
(ppm/°C) *1
Char.
–55°C
Max. Min.
0.58 –0.24 0.40 –0.17 0.25 –0.11
–30°C
–10°C
–55 to +125°C
Max. Min.
Max. Min.
Within ±22%
+22
C0G
0±30
–30 to + 85°C
–25 to + 85°C
Within
–82
%
+30
Within –80
20°C
%
*1: Nominal values denote the temperature coefficient within a range of
25 to 125°C
36
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Radial Lead Type Monolithic Ceramic Capacitors
RDE Series Large Capacitance and High Allowable Ripple Current (For Commercial Use Only) (DC250V-DC630V)
L max.
T max.
■ Features
1. Higher capacitance with DC-Bias; approximately 40%
higher than X7R under loaded rated voltage.
2. Applicable for use as a DC smoothing capacitor in
LED Bulb Lighting circuits after the bridge
rectifier circuit
ød : 0.5±0.05
AC100V input: 250V rating type
maximum capacitance of X7T, 250V is 2.2 micro F
though X7R, 630V is 0.47 micro F.
F±0.8
Dimensions code: 2/3/8
Lead style code: K1
Coating extension does not exceed the end of the lead bend.
Lead Wire : Solder Coated Copper Wire or
AC200V input: 450V rating type
·
(in mm)
Solder Coated CP Wire
maximum capacitance of X7T, 450V is 1.2 micro F
though X7R, 630V is 0.47 micro F.
L max.
T max.
3. Allowable higher ripple current
4. Reduces acoustic noise
Approximately 15dB reduction in comparison to
leaded X7R characteristics parts.
Approximately 30dB reduction in comparison to
SMD X7T characteristics part because the contact
area is smaller than a SMD.
ød : 0.5±0.05
5
5. Maximum capacitance is doubled by the dual chip
structure in the leaded component construction.
F±0.8
Dimensions code: 5
Lead style code: B1
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
■ Applications
(in mm)
1. DC smoothing capacitor for LED bulb
2. PFC capacitor for general use SMPS
3. Replace Al-E capacitor for long-life equipment
T max.
L max.
■ Dimensions
Dimensions (mm)
Dimensions and
Lead Style Code
DC Rated
Voltage
L
W
W1
T
F
d
2K1/2M1
3K1/3M1
5B1/5E1
8K1/8M1
250V/450V/630V 5.5 4.0 6.0
250V/450V/630V 5.5 5.0 7.5
5.0 0.5
5.0 0.5
5.0 0.5
5.0 0.5
5.0 0.5
See
the individual
product
ød : 0.5±0.05
250V/450V/630V 7.5 7.5*
250V/450V/630V 7.5 5.5 8.0
250V/450V/630V 7.7 12.5*
-
F±0.8
specifications
Dimensions code: U
Lead style code: B1
· Lead Wire : Solder Coated Copper Wire or
Solder Coated CP Wire
UB1/UE1
-
(in mm)
*DC630V: W+0.5mm
Continued on the following page.
37
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
■ Marking
Rated Voltage
Temp. Char.
DC250V
DC450V
X7T
DC630V
Dimensions
Code
683
153
153
M K47
M K97
M K77
2
M
M
M
334
104
223
3, 8
5, U
K47
K97
K77
M
M
M
225
474
K97
474
M47
M77
Temperature Characteristics
Nominal Capacitance
Capacitance Tolerance
Rated Voltage
Marked with code (X7T char.: 7)
Marked with 3 figures
Marked with code
Marked with code (DC250V: 4, DC450V: 9, DC630V: 7)
M
Marked with
Manufacturer's Identification
High Dielectric Constant Type, X7T Characteristics
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDED72E333K2ppC11p
RDED72E473K2ppC11p
RDED72E683K2ppC11p
RDED72E104K3ppC11p
RDED72E154K3ppC11p
RDED72E224K8ppC11p
RDED72E334K8ppC11p
RDED72E474K5ppC13p
RDED72E684K5ppC13p
RDED72E105K5ppC13p
RDED72E225MUppC13p
RDED72W103K2ppC11p
RDED72W153K2ppC11p
RDED72W223K2ppC11p
RDED72W333K2ppC11p
RDED72W473K2ppC11p
RDED72W683K3ppC11p
RDED72W104K3ppC11p
RDED72W154K8ppC11p
RDED72W224K5ppC13p
RDED72W334K5ppC13p
RDED72W474K5ppC13p
RDED72W564K5ppC13p
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
250
250
250
250
250
250
250
250
250
250
250
450
450
450
450
450
450
450
450
450
450
450
450
450
450
630
630
630
630
630
630
630
630
630
33000pF ±10%
47000pF ±10%
68000pF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
0.33µF ±10%
0.47µF ±10%
0.68µF ±10%
1.0µF ±10%
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
7.5 x 5.5
7.5 x 5.5
7.5 x 7.5
7.5 x 7.5
7.5 x 7.5
7.7 x 12.5
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
7.5 x 5.5
7.5 x 7.5
7.5 x 7.5
7.5 x 7.5
7.5 x 7.5
7.7 x 12.5
7.7 x 12.5
5.5 x 4.0
5.5 x 4.0
5.5 x 5.0
5.5 x 5.0
5.5 x 5.0
7.5 x 5.5
7.5 x 8.0
7.5 x 8.0
7.5 x 8.0
3.15
3.15
3.15
4.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
K1
K1
K1
K1
K1
K1
K1
B1
B1
B1
B1
K1
K1
K1
K1
K1
K1
K1
K1
B1
B1
B1
B1
B1
B1
K1
K1
K1
K1
K1
K1
B1
B1
B1
M1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5
M1
M1
M1
M1
M1
M1
E1
4.0
4.0
4.0
4.5
4.5
E1
4.5
E1
2.2µF ±20%
4.5
E1
10000pF ±10%
15000pF ±10%
22000pF ±10%
33000pF ±10%
47000pF ±10%
68000pF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
0.33µF ±10%
0.47µF ±10%
0.56µF ±10%
1.0µF ±20%
3.15
3.15
3.15
3.15
3.15
4.0
M1
M1
M1
M1
M1
M1
M1
M1
E1
4.0
4.0
4.5
4.5
E1
4.5
E1
4.5
E1
RDED72W105MUppC13p X7T
RDED72W125MUppC13p X7T
4.5
E1
1.2µF ±20%
4.5
E1
RDED72J103K2ppC11p
RDED72J153K2ppC11p
RDED72J223K3ppC11p
RDED72J333K3ppC11p
RDED72J473K3ppC11p
RDED72J683K8ppC11p
RDED72J104K5ppC13p
RDED72J154K5ppC13p
RDED72J224K5ppC13p
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
X7T
10000pF ±10%
15000pF ±10%
22000pF ±10%
33000pF ±10%
47000pF ±10%
68000pF ±10%
0.10µF ±10%
0.15µF ±10%
0.22µF ±10%
3.15
3.15
4.0
M1
M1
M1
M1
M1
M1
E1
4.0
4.0
4.0
4.5
4.5
E1
4.5
E1
Continued on the following page.
38
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Continued from the preceding page.
Rated
Voltage
(Vdc)
Dimensions Dimension
Lead
Space F
(mm)
Lead Style Lead Style
Lead Style
Code
Taping (2)
Temp.
Char.
Part Number
Capacitance
LxW
T
Code
Bulk
Code
(mm)
(mm)
Taping (1)
RDED72J274K5ppC13p
RDED72J474MUppC13p
RDED72J564MUppC13p
X7T
X7T
X7T
630
630
630
0.27µF ±10%
0.47µF ±20%
0.56µF ±20%
7.5 x 8.0
7.7 x 13.0
7.7 x 13.0
4.5
4.5
4.5
5.0
5.0
5.0
B1
B1
B1
E1
E1
E1
-
-
-
Two blank columns are filled with the lead style code. Please refer to the 3 columns on the right for the appropriate code.
The last blank column is filled with the packaging code. (B: bulk, A: ammo pack)
5
39
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
No.
1
Item
Specifications
Test Method
Operating Temperature
Range
-55 to +125˚C
–
2
3
Appearance
No defects or abnormalities
See previous pages
Visual inspection
Dimension and Marking
Visual inspection, Vernier Caliper
The capacitor should not be damaged when voltage
in Table is applied between the terminations
for 1 to 5 sec.
(Charge/Discharge current V 50mA)
Between
Terminals
No defects or abnormalities
Rated Voltage
DC250V
Test Voltage
200% of the rated voltage
150% of the rated voltage
120% of the rated voltage
DC450V
DC630V
Dielectric
Strength
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuit, is kept approximately
2mm from the balls as shown in
the figure, and 200% of the rated
DC voltage is impressed for 1 to 5
sec. between capacitor terminals
and metal balls.
4
Body
Insulation
Approx. 2mm
Metal balls
No defects or abnormalities
(Charge/Discharge current
V 50mA)
The insulation resistance should be measured with
DC500±50V (DC250±25V in case of rated voltage:
DC250V,DC450V) at normal temperature and humidity
and within 2 min. of charging.
Insulation
Resistance
Between
Terminals
5
More than 10,000MΩ or 100MΩ · µF, Whichever is smaller
5
(Charge/Discharge current V 50mA)
The capacitance/D.F. should be measured at the
frequency of 1T0.1kHz and a voltage of
AC1T0.2V(r.m.s.).
6
7
Capacitance
Within the specified tolerance
0.01 max.
Dissipation Factor (D.F.)
The capacitance change should be measured after
5 min. at each specified temperature stage.
Step
Temperature (˚C)
25T2
Capacitance
Temperature
Characteristics
1
2
3
4
5
8
Within +22/-33%
-55T3
25T2
125T3
25T2
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10T1 sec.
Tensile
Strength
Termination not to be broken or loosened
Terminal
Strength
9
F
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
Appearance
No defects or abnormalities
Within the specified tolerance
The capacitor should be firmly soldered to the
supporting lead wire and vibrated at a frequency range
of 10 to 55Hz, 1.5mm in total amplitude, with about a 1
minute rate of vibration change from 10Hz to 55Hz and
back to 10Hz. Apply for a total of 6 hrs., 2 hrs. each in 3
mutually perpendicular directions.
Capacitance
Vibration
Resistance
D.F.
10
0.01 max.
Continued on the following page.
40
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Test Method
The terminal of a capacitor is dipped into a solution of
ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin
in weight proportion) and then into molten solder (JIS-
Z-3282) for 2T0.5 sec. In both cases the depth of
dipping is up to about 1.5 to 2mm from the terminal
body.
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
11 Solderability of Leads
Temp. of solder: 245T5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5˚C H60A or H63A Eutectic Solder
Appearance
No defects or abnormalities
The lead wire is immersed in the melted solder 1.5 to
2mm from the main body at 350T10˚C for 3.5T0.5 sec.
The specified items are measured after 24T2 hrs.
Capacitance
Change
Resistance
to
Soldering
Heat
Within T10%
12
Dielectric
Strength
(Between
Terminals)
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
No defects
Appearance
No defects or abnormalities
The capacitor should be subjected to 5 temperature
cycles.
Capacitance
Change
Within T7.5%
Step
Temperature (˚C)
-55T3
Time (min)
30T3
1
2
3
4
D.F.
0.01 max.
Room Temp.
125T3
3 max.
30T3
Temperature
Cycle
13
Insulation
Resistance
More than 10,000MΩ or 100MΩ · µF (Whichever is smaller)
Room Temp.
3 max.
Dielectric
Strength
(Between
Terminals)
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
No defects or abnormalities
Appearance
No defects or abnormalities
Set the capacitor at 40T2˚C and relative humidity of 90
W24
Y 0
5
to 95% for 500
hrs. Remove and set for 24T2 hrs.
Capacitance
Change
Within T12.5%
Humidity
at room temperature, then measure.
14 (Steady
State)
D.F.
0.02 max.
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
Insulation
Resistance
More than 1,000MΩ or 10MΩ · µF (Whichever is smaller)
Appearance
No defects or abnormalities
Within T12.5%
Apply the rated voltage at 40T2˚C and relative humidity
W24
Y 0
of 90 to 95% for 500
hrs. Remove and set for
Capacitance
Change
24T2 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
Humidity
Load
15
D.F.
0.02 max.
• Pretreatment
Perform a heat treatment at 150+0/-10˚C for 1 hr., and
then let sit at room temperature for 24T2 hrs.
Insulation
Resistance
More than 1,000MΩ or 10MΩ · µF (Whichever is smaller)
W48
Appearance
No defects or abnormalities
Within T12.5%
Apply voltage in Table for 1000
hrs. at the
Y 0
maximum operating temperature. Remove and set for
24T2 hrs. at room temperature, then measure.
(Charge/Discharge current V 50mA)
Capacitance
Change
D.F.
0.02 max.
Rated Voltage
DC250V
DC450V
Test Voltage
High
16 Temperature
Load
150% of the rated voltage
130% of the rated voltage
120% of the rated voltage
DC630V
Insulation
Resistance
More than 1,000MΩ or 10MΩ · µF (Whichever is smaller)
• Pretreatment
Apply test voltage for 1 hr., at test temperature. Remove
and set for 24T2 hrs. at room temperature.
Appearance
Marking
No defects or abnormalities
Legible
The capacitor should be fully immersed, unagitated, in
reagent at 20 to 25 ˚C for 30T5 sec. and then removed
gently. Marking on the surface of the capacitor should
immediately be visually examined.
Reagent :
Solvent
17
Resistance
• Isopropyl alcohol
41
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
RPE Series Characteristics Reference Data (Typical Example)
■ Capacitance - Temperature Characteristics
Temperature Compensating Type
High Dielectric Constant Type
10
20
0
5
X7R
−20
−40
−60
−80
C0G
0
−5
Y5V
−10
−60
−40
−20
0
20
40
60
80
100
120
−50
−25
0
25
50
75
100
125
Temperature (˚C)
Temperature (˚C)
■ Capacitance - DC Voltage Characteristics
■ Capacitance Change - Aging
C0G : 1MHz, AC1V (r.m.s.)
X7R•Y5V : 1kHz, AC1V (r.m.s.)
+40
+20
0
+10
0
C0G
C0G 50V
X7R
Y5V
−10
−20
−30
−20
−40
−60
−80
5
X7R 50V
Y5V 50V
−40
−50
100
1,000
10,000
Pass Time (Hr)
0
10
20
30
40
50
DC Voltage (V)
■ Capacitance - Resonant Frequency
■ Impedance - Frequency Characteristics
10
1000
1000pF
l=2mm
l=5mm
l=10mm
0.01µF
100
1
0.1µF
100pF
10pF
1µF
10
0.1
0.5
Temp. Compensating
High Dielectric Constant
1
0.01
1
10pF
100pF
1000pF
0.01µF
0.1µF
1µF
10
100
1000
Capacitance
Frequency (MHz)
42
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
RPE Series Small Size, Large Capacitance Characteristics Reference Data (Typical Example)
■ Capacitance - Temperature Characteristics
■ Capacitance - DC Voltage Characteristics
20
15
10
5
20
0
-20
-40
-60
-80
0
-5
-10
-15
-20
0
10
20
30
40
50
-75
-50
-25
0
25
50
75
100
125
150
DC Voltage (V)
Temperature (°C)
■ Impedance - Frequency Characteristics
100
10
1
0.1
5
1.0µF
4.7µF
0.01
2.2µF
0.001
0.1
1
10
100
1000
Frequency (MHz)
43
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
RH Series Characteristics Reference Data (Typical Example)
■ Capacitance - Temperature Characteristics
■ Capacitance - DC Voltage Characteristics
25°C, 1kHz, AC1V(r.m.s.)
1kHz, AC1V(r.m.s.) without DC bias
10
10
0
X8G
X8G
0
-10
X8L
-10
-20
-30
-40
-50
-60
X8L 100V
-20
-30
-40
-50
-60
X8L 50V
-75
-50
-25
0
25
50
75
100
125
150
0
10
20
30
40
50
60
70
80
90
100
Temperature (°C)
DC Voltage (V)
■ Capacitance Change - Aging
■ Impedance - Frequency Characteristics
10
25°C, 1kHz, AC1V(r.m.s.) without DC bias
10
0
1000pF
X8G
X8L
0.01µF
1
-10
-20
-30
-40
-50
0.1µF
100pF
5
1µF
0.1
X8G
X8L
0.01
1
10
100
1,000
Pass Time (Hr)
10,000
100,000
10
100
1000
Frequency (MHz)
44
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
RDE Series Characteristics Reference Data (Typical Example)
■ Capacitance - Temperature Characteristics
1kHz, AC1V(r.m.s.) without DC bias
20
C0G
0
X7R
X7S
X7T
−20
−40
−60
F/Y5V
−80
−100
−75
−50
−25
0
25
50
75
100
125
150
Temperature (°C)
■ Capacitance - DC Voltage Characteristics
Rated Voltage: DC25V to DC100V
Rated Voltage: DC250V to DC630V
1kHz, AC1V (r.m.s.)
1kHz, AC1V (r.m.s.)
20
0
+20
0
−20
−40
−60
−80
−100
−20
−40
−60
−80
−100
X7T 250V
X7T 630V
X7R 630V
X7T 450V
X7R DC50V
X7S DC50V
X7R DC100V
X7S DC100V
5
X7R 250V
X7S DC25V
F/Y5V DC50V
60
0
20
40
80
100
0
100
200
300
400
500
600
700
DC Voltage (V)
DC Voltage (V)
■ Capacitance Change - Aging
■ Capacitance - Resonant Frequency
1000
+10
0
l=5mm
100
−10
−20
−30
10
ø0.5
−40
−50
1
100
1,000
10,000
10pF
100pF
1000pF
0.01µF
0.1µF
1µF
Pass Time (Hr)
Capacitance
■ Impedance - Frequency Characteristics
1000
100
10
1
0.01µF
0.1
0.1µF
1µF
22µF
0.01
0.1
1
10
100
1000
Frequency (MHz)
45
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Packaging
Packaging
Two types of packaging for monolithic ceramic capacitors are available.
1. Bulk Packaging
Minimum Quantity
Dimensions Code
Dimensions (LZW)
4.0Z3.5mm or 5.0Z3.5mm (Depends on Part Number List)
4.0Z3.5mm or 4.5Z3.5mm or 5.0Z3.5mm (Depends on Part Number List)
5.0Z3.5mm or 5.5Z4.0mm or 5.7Z4.5mm (Depends on Part Number List)
5.0Z4.5mm or 5.5Z5.0mm or 6.0Z5.5mm (Depends on Part Number List)
7.5Z7.5mm (DC630V: 7.5Z8.0mm)
Minimum Quantity (pcs./Bag)
0
1
2
3
5
500*1
6
10.0Z10.0mm
8
7.5Z5.5mm
W
7
5.5Z7.5mm or 6.0Z8.0mm (Depends on Part Number List)
12.5Z12.5mm
100
200
U
7.7Z12.5mm (DC630V: 7.7Z13.0mm)
Please order with an integral multiple of the minimum quantity above.
*1 400 pcs. for RHDL81HpppK3ppC03B
250 pcs. for RHDL81H106MWK1C03B
2. Tape Carrier Packaging
5
(1) Dimensions of Ammo Pack
(in mm)
(2) Minimum Quantity
Dimensions Code
Dimensions (LZW)
Minimum Quantity (pcs./Ammo Pack)
0
1
4.0Z3.5mm or 5.0Z3.5mm (Depends on Part Number List)
4.0Z3.5mm or 4.5Z3.5mm or 5.0Z3.5mm (Depends on Part Number List)
5.0Z3.5mm or 5.5Z4.0mm or 5.7Z4.5mm (Depends on Part Number List)
5.0Z4.5mm or 5.5Z5.0mm or 6.0Z5.5mm (Depends on Part Number List)
7.5Z7.5mm (DC630V: 7.5Z8.0mm)
2000*2
2
3
5
2000*3
1500*4
1000*5
6
10.0Z10.0mm
8
7.5Z5.5mm
W
U
5.5Z7.5mm or 6.0Z8.0mm (Depends on Part Number List)
7.7Z12.5mm (DC630V: 7.7Z13.0mm)
Please order with an integral multiple of the minimum quantity above.
*2 1500 pcs. for RPER71H335K3M1C60A, RPER71H475K3M1C60A, RDER71H335K3ppC03A, RDEC71E226K3ppC03A, RDEC72A155K3ppC03A,
RDEC72A225K3ppC03A and RHD Series
*3 1500 pcs. for RPER71H335K5ppC03A, RPER71H475K5ppC03A, RPER72A105K5ppC03A and RDE Series
(Two blank columns are filled with the lead style code.)
*4 1000 pcs. for RHDL81H106MWM1C03Aꢀ
*5 1500 pcs. for RDED72W105MUE1C13A, RDER72E105MUE1C13A, RDER72J474MUE1C13A
"Minimum Quantity" means the numbers of units of each delivery or order. The quantity should be an integral multiple of the "minimum quantity." (Please note that the actual
delivery quantity in a package may change sometimes.)
Continued on the following page.
46
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Packaging
Continued from the preceding page.
Taping Dimensions
Inside Crimp Taping
Straight Taping
P2
P
P2
P
P1
F
P1
F
H0
H
W
W
2
0
L
W
W
2 W1
W1
L
W
W
0
R
R
øD0
P0
P0
ød
Direction of feed
ød
Direction of feed
øD0
Dimensions and Lead style code
0M1
Dimensions (LZW)
4.0Z3.5mm
Dimensions and Lead style code
Dimensions (LZW)
4.0Z3.5mm
1DB
2DB
3DB
5E1
5E2
6E1
6E2
5.7Z4.5mm
4.0Z3.5mm or 4.5Z3.5mm
(Depends on Part Number List)
1M1
6.0Z5.5mm
2M1
2M2
3M1
3M2
8M1
8M2
WM1
5.0Z3.5mm or 5.5Z4.0mm or 5.7Z4.5mm
(Depends on Part Number List)
7.5Z7.5mm
(DC630V: 7.5Z8.0mm)
5.0Z4.5mm or 5.5Z5.0mm
(Depends on Part Number List)
10.0Z10.0mm
7.7Z12.5mm
(DC630V: 7.7Z13.0mm)
7.5Z5.5mm
5.5Z7.5mm
UE1
Outside Crimp Taping
P2
P
Item
Code
Dimensions (mm)
5
Pitch of Component
Pitch of Sprocket Hole
P
12.7T1.0
P0
12.7T0.2
W0.4
P1
F
2.5
(DB) (S1) (S2)
Y0.2
H0
Lead Spacing
F
W0.6
5.0
W
2 W1
L
Y0.2
W
Length from Hole Center to
Component Center
W
0
P2
P1
6.35T1.3
R
øD0
P0
ød
Direction of feed
3.85T0.7
Length from Hole Center to
Lead
5.1T0.7 (DB) (S1) (S2)
Dimensions and Lead style code
Dimensions (LZW)
5.0Z3.5mm
254T1.5 Total length of components pitch Z 20
0S1
1S1
2S1
2S2
3S1
3S2
Body Dimension
Depends on Part Number List
Deviation Along Tape, Left
or Right Defect
∆S
T2.0
5.0Z3.5mm or 5.5Z4.0mm
(Depends on Part Number List)
Carrier Tape Width
W
18.0T0.5
W0
Position of Sprocket Hole
Lead Distance between
Reference and Bottom Plane
For Straight Lead Type
Diameter of Sprocket Hole
Lead Diameter
W1
9.0
5.0Z4.5mm or 5.5Z5.0mm
(Depends on Part Number List)
Y0.5
16.0T0.5 (M1) (S1)
20.0T0.5 (M2) (S2)
20T0.5 (E2),17.5T0.5 (E1),16T0.5 (DB)
4.0T0.1
H0
H
D0
d
0.5T0.05
Total Tape Thickness
Total Thickness of Tape
and Lead Wire
t1
0.6T0.3
t2
T
1.5 max.
0
∆S
∆h1
∆h2
T max.
Body Thickness
Depends on Part Number List
∆h1 1.0 max. (RHD Series: 1.5 max.,
∆h2 Dimensions code W, U: 2.0 max.)
Deviation Across Tape
Portion to Cut in Case of
Defect
W0
11.0
L
Y1.0
Protrusion Length
Hold Down Tape Width
Hold Down Tape Position
Coating Extension
R
W0
W2
0.5 max.
9.5 min.
1.5T1.5
t2
t1
Depends on Dimensions
47
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
!Caution
■ !Caution (Storage and Operating Condition)
Operating and storage environment
The insulating coating of capacitors does not form a
perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially
where chloride gas, sulfide gas, acid, alkali, salt
or the like are present. Also avoid exposure to
moisture. Before cleaning, bonding or molding this
product, verify that these processes do not affect
product quality by testing the performance of a
cleaned, bonded or molded product in the intended
equipment. Store the capacitors where the
temperature and relative humidity do not exceed 5
to 40 degrees centigrade and 20 to 70%.
Use capacitors within 6 months after delivery.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
5
48
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
!Caution
■ !Caution (Rating)
1. Operating Voltage
When DC-rated capacitors are to be used in AC or ripple
current circuits, be sure to maintain the Vp-p value of the
applied voltage or the V0-p which contains DC bias within
the rated voltage range.
When DC-rated capacitors are to be used in input circuits
from commercial power source (AC filter), be sure to use
Safety Recognized Capacitors because various
regulations on withstand voltage or impulse withstand
established for all equipment should be taken into
consideration.
When the voltage is applied to the circuit, starting or
stopping may generate irregular voltage for a transit
period because of resonance or switching. Be sure to
use a capacitor with a rated voltage range that includes
these irregular voltages.
Voltage
DC Voltage
DC+AC Voltage
AC Voltage
Pulse Voltage (1)
Pulse Voltage (2)
Positional
Measurement
V0-p
V0-p
Vp-p
Vp-p
Vp-p
2. Operating Temperature and Self-generated Heat
Keep the surface temperature of a capacitor below the
upper limit of its rated operating temperature range. Be
sure to take into account the heat generated by the
capacitor itself. When the capacitor is used in a high-
frequency current, pulse current or similar current, it may
have self-generated heat due to dielectric loss. In the
case of "High Dielectric Constant Type Capacitors,"
applied voltage load should be such that self-generated
heat is within 20 °C under the condition where the
capacitor is subjected at an atmosphere temperature of
25 °C. Please contact us if self-generated heat occurs
with "Temperature Compensating Type Capacitors".
When measuring, use a thermocouple of small thermal
capacity -K of ø0.1mm under conditions where the
capacitor is not affected by radiant heat from other
components or wind from surroundings. Excessive heat
may lead to deterioration of the capacitor's characteristics
and reliability. Never attempt to perform measurement
with the cooling fan running. Otherwise, accurate
measurement cannot be ensured.
5
3. Fail-Safe
Be sure to provide an appropriate fail-safe function on
your product to prevent a second damage that may be
caused by the abnormal function or the failure of our
product.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
49
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
!Caution
■ !Caution (Soldering and Mounting)
1. Vibration and impact
4. Treatment after bonding, resin molding and coating
When the outer coating is hot (over 100 degrees
centigrade) after soldering, it becomes soft and fragile,
so please be careful not to give it mechanical stress.
Do not expose a capacitor or its leads to excessive
shock or vibration during use.
2. Soldering
When soldering this product to a PCB/PWB, do not
exceed the solder heat resistance specification of
the capacitor. Subjecting this product to excessive
heating could melt the internal junction solder and
may result in thermal shocks that can crack the
ceramic element.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
3. Bonding, resin molding and coating
In case of bonding, molding or coating this product,
verify that these processes do not affect the quality
of the capacitor by testing the performance of the
bonded, molded or coated product in the intended
equipment.
In case the amount of application, dryness/
hardening conditions of adhesives and molding resins
containing organic solvents (ethyl acetate, methyl
ethyl ketone, toluene, etc.) are unsuitable, the
outer coating resin of a capacitor may be damaged
by the organic solvents and may result, worst case,
in a short circuit.
5
The variation in thickness of adhesive or molding
resin or coating may cause an outer coating resin
cracking and/or ceramic element cracking of a
capacitor in a temperature cycling.
■ !Caution (Handling)
Vibration and impact
Do not expose a capacitor or its leads to excessive
shock or vibration during use.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
50
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
!Note
C49E.pdf
Notice
■ Notice (Rating)
Capacitance change of capacitor
In case of F/X7R/X7S/X7T/X8L/Y5V char.
Capacitors have an aging characteristic, whereby
the capacitor continually decreases its capacitance
slightly if the capacitor is left on for a long
time. Moreover, capacitance might change greatly
depending on the surrounding temperature or an
applied voltage.
■ Notice (Soldering and Mounting)
1. Cleaning (ultrasonic cleaning)
To perform ultrasonic cleaning, observe the following
conditions.
Rinse bath capacity: Output of 20 watts per liter or less.
Rinsing time: 5 min. maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue
destruction of the lead wires.
2. Soldering and Mounting
(1) Allowable Conditions for Soldering Temperature and Time
300
5
Dimensions Code
1, 2 (F: 2.5mm)
0, 1, 2 (F: 5.0mm), 3, 8, W
5, 6, 7, U
q
w
e
280
270
260
240
220
e
q
w
5
10
15
20
Accumulated Immersion Time (sec.)
Perform soldering within tolerance range (shaded portion).
(2) Insertion of the Lead Wire
• When soldering, insert the lead wire into the PCB without
mechanically stressing the lead wire.
• Insert the lead wire into the PCB with a distance appropriate
to the lead space.
51
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
C49E.pdf
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering. May.10,2011
相关型号：
RPE5C1H680J1A1Y03B
CAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.000068uF, THROUGH HOLE MOUNT, RADIAL LEADED
MURATA
RPE5C1H681J2P1A03B
Ceramic Capacitor, Multilayer, Ceramic, 50V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.00068uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT
MURATA
RPE5C1H6R0D2P1B03B
Ceramic Capacitor, Multilayer, Ceramic, 50V, 8.33% +Tol, 8.33% -Tol, C0G, 30ppm/Cel TC, 0.000006uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT
MURATA
RPE5C1H7R0D1A1Y03B
CAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.000007uF, THROUGH HOLE MOUNT, RADIAL LEADED
MURATA
RPE5C1H820J1A1Y03B
CAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.000082uF, THROUGH HOLE MOUNT, RADIAL LEADED
MURATA
RPE5C1H821J2P1A03B
Ceramic Capacitor, Multilayer, Ceramic, 50V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.00082uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT
MURATA
RPE5C1H9R0D1A1Y03B
CAPACITOR, CERAMIC, MULTILAYER, 50V, C0G, 0.000009uF, THROUGH HOLE MOUNT, RADIAL LEADED
MURATA
RPE5C2A100J1A1Y03B
CAPACITOR, CERAMIC, MULTILAYER, 100V, C0G, 0.00001uF, THROUGH HOLE MOUNT, RADIAL LEADED
MURATA
RPE5C2A100J2P1Z03B
Ceramic Capacitor, Multilayer, Ceramic, 100V, 5% +Tol, 5% -Tol, C0G, 30ppm/Cel TC, 0.00001uF, Through Hole Mount, 2010, RADIAL LEADED, ROHS COMPLIANT
MURATA
©2020 ICPDF网 联系我们和版权申明