SV01A103CEA01 [MURATA]

Wire Wound Potentiometric Sensor, 333.3deg Max, Rectangular, Surface Mount, ROHS COMPLIANT-4;


型号：	SV01A103CEA01
厂家：	muRata
描述：	Wire Wound Potentiometric Sensor, 333.3deg Max, Rectangular, Surface Mount, ROHS COMPLIANT-4 传感器换能器
文件：	总7页 (文件大小：195K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

^{• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering}0^.7.3.20

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Rotary Position Sensors

SMD/Lead Dust-proof Type 12mm Size SV01 Series

2.1

0.6

■ Features

+0.1

-0

4.0

Dia.

1. Dust-proof construction protects the interior from

dust, which maintains stable characteristics.

2. Compliant to high peak temperature lead free

soldering.

0.2

1.0

#1 #2 #3

11.0

3. Excellent resistance materials and high reliability

wiper achieves 1M cycles.

4. D formation thru-hole rotor enables selection of

any kind of gear shape.

4-0.8±0.1

SV01A

5.0

Tolerance : ±0.3

5. Both D formation thru-hole rotor and T formation

thru-hole rotor are available.

(

)

8.5±0.1

in mm

6. Leaded terminal type is available.

7. Ultra-thin size (2.1mm height)

Mounting Face

+0.1

2.9 3.5

8. Au plated terminals without Lead.

9. Complies with RoHS directive.

4.0

Dia.

-0

■ Applications

1. Animal robot

#1#2 #3

4-0.8±0.2

11.0

5.0

2. Switch for automotive

3. Motor drive unit

4. Radio control equipment

5. Car audio (navigation system, changer)

SV01L

Tolerance : ±0.3

5.0

(

)

in mm

■ T formation Thru-hole rotor

+0.1

-0

4.0

Dia.

1.2

Tolerance : ±0.3

(

)

in mm

Total Resistance Value

(k ohm)

Linearity

(% )

Part Number

Effective Rotational Angle

333.3° (Ref.)

Rotational Torque

Rotational Life

1M cycles

• •

2mN m (Ref.; 21gf cm) max.

SV01A103pEA01

SV01L103pEA11

10 ±30%

±2

•

333.3° (Ref.)

2mN m (Ref.; 21gf cm) max.

1M cycles

A blank column is filled with Rotor Formation Codes. (A: D formation thru-hole rotor C: T formation thru-hole rotor)

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

■ Construction

Rotor

Cover

#2 Terminal

Resin Substrate

#3 Terminal

#2 Terminal

#1 Terminal

Wiper

Resistive Element

■ Standard Land Pattern

■ Standard Mounting Holes

SV01A

SV01L

+0.1

-0

4-1.0

Dia.

(1.1)

2.5

4-1.8

5.0

Tolerance: ±0.1

(

)

in mm

(8.5)

(

)

in mm

■ Characteristics

∆TR

Linearity: ±3%

: ±20%

Temperature Cycle

(Thermal Shock)

∆TR

Linearity: ±3%

: ±20%

Humidity

∆TR : ±10%

Vibration

Linearity: ±3%

∆TR : ±10%

Shock (20G)

Humidity Load Life

Linearity: ±3%

∆TR : ±20%

Linearity: ±3%

∆TR

Linearity: ±3%

: +5/-30%

High Temperature

Exposure

∆TR

Linearity: ±3%

: ±20%

Low Temperature

Exposure

∆TR

: ±20%

Rotational Life

Linearity: ±3% (1M cycles)

∆TR: Total Resistance Change

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

SV01 Series Notice

■ Notice (Operating and Storage Conditions)

1. Store in temperatures of -10 to +40deg. C and

(1) Corrosive gasses atmosphere

(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia

gas, Sulfuric acid gas, Nitric oxide gas, etc.)

(2) In liquid

relative humidity of 30-85%.

2. Do not store in or near corrosive gases.

3. Use within six months after delivery.

4. Open the package just before using.

5. Do not store under direct sunlight.

(Ex. Water, Oil, Medical liquid, Organic

solvent, etc.)

6. Do not use the rotary position sensor under the

following environmental conditions. If you use

the rotary position sensor in an environment other

than listed below, please consult a Murata factory

representative prior to using.

(3) Dusty / dirty atmosphere

(4) Direct sunlight

(5) Static voltage nor electric/magnetic fields

(6) Direct sea breeze

(7) Other variations of the above

■ Notice (Soldering and Mounting)

1. Soldering

(5) The soldering iron should not come in contact

with the cover of the rotary position sensor. If

such contact does occur, the rotary position

sensor may be damaged.

(1) SV01 series can be soldered by reflow soldering

method and soldering iron. Do not use flow

soldering method (dipping).

(2) The dimension of land pattern used should be

Murata's standard land pattern at reflow

soldering. Excessive land area may cause

displacement due to the effect of the surface

tension of the solder. Insufficient land area

may cause insufficient soldering strength on PCB

(SMD Type).

2. Mounting

(1) Use PCB hole to meet the pin of the rotary

position sensor. If the rotary position sensor

is inserted into insufficient PCB hole, the

rotary position sensor may be damaged by

mechanical stress. (Lead type)

(2) Do not apply excessive force, preferable 9.8N

max. (Ref. 1kgf) when the rotary position sensor

is mounted to the PCB.

(3) Soldering conditions

Refer to the temperature profile.

If the soldering conditions are not suitable,

e.g., excessive time and/or excessive temperature,

the rotary position sensor may deviate from the

specified characteristics.

(3) Do not warp and/or bend PCB to prevent the rotary

position sensor from breakage.

3. Cleaning

Cannot be cleaned because of open construction.

(4) The amount of solder is critical. Insufficient

amounts of solder can lead to insufficient

soldering strength on PCB. Excessive amounts of

solder may cause bridging between the

terminals.

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

SV01 Series Notice

■ Soldering Profile

Reflow Soldering Profile

1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu)

Limit Profile

Standard Profile

Time (s)

Standard Profile

Heating

Limit Profile

Heating

Peak

Temperature

(T3)

Peak

Temperature

Temp. (T1) Time (t1) Temp. (T4) Time (t3)

(T5)

Pre-heating

Cycle of

Reflow

Cycle of

Reflow

Series

Temp. (T1) Time (t1) Temp. (T2) Time (t2)

°C

sec.

°C

sec.

°C

Time

°C

sec.

°C

sec.

°C

Time

SV01A

150 to 180 60 to 120

220

30 to 60

245±3

150 to 180 60 to 120

230

30 to 50 260 +5/-0

2. Soldering profile for Eutectic solder (63Sn/37Pb)

(Limit profile: refer to 1)

Standard Profile

Heating

Peak

Temperature

(T3)

Pre-heating

Cycle of

Reflow

Series

Temp. (T1) Time (t1) Temp. (T2) Time (t2)

°C

sec.

°C

sec.

°C

Time

Standard Profile

SV01A

150

60 to 120

183

230

Time (s)

Soldering Iron

Standard Condition

Series

Temperature of Soldering Iron Tip

Soldering Time

sec.

Soldering Iron Power Output

Cycle of Soldering Iron

°C

Time

SV01

350±10

3 max.

30 max.

■ Notice (Handling)

Uncontrolled mechanical force (except usual rotation on

the hollow rotor of product) may cause a change of

electrical characteristics, an increase of rotational

torque or mechanical damage of the product.

Therefore, please consider the following points

for your design.

1. The product must be soldered by the terminals.

Do not affix by screw clamping to support board

as this could cause mechanical deformation.

2. The connecting shaft must be sustained by the

bearing. No uncontrolled force should be applied

to the hollow rotor.

■ Notice (Other)

1. Please make sure the connecting impedance is not

less than 10M ohm. The rotary position sensor

is designed to connect the output terminal and A/D

port of the microprocessor directly. Therefore,

connecting impedance presupposes certain M ohm and

the contact resistance is set high.

(2) Data considered as error should be invalid.

(3) If suspicious data is found, the data should be

re-installed.

3. Before using rotary position sensor, please test

after assembly in your particular mass production

system.

2. To minimize processing errors and rare cases of

noise influence when data is installed,

please consider the following when programming

your software.

4. MURATA cannot guarantee rotary position sensor

integrity when used under conditions other than

those specified in this document.

(1) Data install should be done plural times and

applied the mean value.

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

Rotary Position Sensors SMD/Lead Dust-proof Type (SV01) Specifications and Test Methods

The tests and measurements should be conducted under the condition of 15 to 35°C of temperature 25 to 75% of relative humidity and 86 to 106 kpa of

atmospheric pressure unless otherwise specified. If questionable results occur that have been measured in accordance with the above mentioned

conditions, the tests and measurements should be conducted under the condition of 25±2°C of temperature, 45 to 55% of relative humidity and 86 to

106 kpa of atmospheric pressure. When the potentiometer is tested after soldering on PCB, it should be tested after being kept in a room (15 to 35°C,

25 to 75%RH) over 24 hours except "Resistance to soldering heat".

Test Methods

No.

Item

Independent linearity should vary no more than ±2% within ±160° to 50% voltage ratio.

Taper : linear, 100%/333.3° Measured with the circuit as below (Figure 1).

100%

Guarantee limit for linearity

DC5V (#3)

GND (#1)

Output voltage ratio (%)

V (1-2)

V (1-3)

50%

Connection Impedance : 1M ohm min.

Output (#2)

X100

Linearity

100% / 333.3°

-160°

0°

Rotational angle (°)

+160°

CCW

Figure-1

The rotary position sensor should be subjected to each of the following temperatures (see Table 1) for 30-45 minutes.

Temperature coefficient of resistance should be applied to the following formula.

R²– R1

R1 (t2 – t1)

TCR=

Z 10⁶(ppm/°C)

t¹: Reference temperature in degrees celsius

t²: Test temperature in degrees celsius

R¹: Resistance at reference temperature in ohm

R²: Resistance at test temperature in ohm

Temperature

Coefficient of

Resistance

Sequence

Temperature (°C)

+25

-40

+25

+85

Note * : Reference temperature

Table 1: Test temperatures

The rotary position sensor should be subjected to Table 2 temperature for 5 cycles.

Then, the rotary position sensor should be kept in the dry box for 24 +8/-0 hrs.

Temperature

Cycle

(Thermal Shock)

Sequence

Temperature (°C)

Time (min.)

-40±3

+25±2

5 max.

+85±3

+25±2

5 max.

Table 2: One cycle of temperature cycle

The rotary position sensor should be stored in a chamber at temperature of +60±2°C and relative humidity of 90-95% for 250±8

hrs. After removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.

Humidity

Vibration

The rotary position sensor should be tested under the condition of the amplitude of 1.5mm, the frequency range from 10 to 55Hz

(should be traversed in approximately one minute) and 2 hours in each of 3 mutually perpendicular directions (total 6 hours).

Then, the rotary position sensor should be kept in the dry box for 1-2 hrs.

The rotary position sensor should be tested under the condition of the peak acceleration 20G max. in half-sine wave and 5 shocks

in each of 3 mutually perpendicular directions (total 15 shocks). Then, the rotary position sensor should be kept in the dry box for

1-2 hrs.

Shock

Full rated continuous working voltage not exceeding 5Vdc should be applied intermittently between terminal #1 and terminal #3 of

the rotary position sensor, 1.5 hours on and 0.5 hours off, for 96±4 hours in total in a chamber at a temperature of +40±2°C and

relative humidity of 90-95%. After removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-

0 hours.

Humidity Load

Life

High Temp.

Exposure

The rotary position sensor should be stored in a chamber at the temperature of +85±3°C without loading for 250±8 hours. After

removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.

Low Temp.

Exposure

The rotary position sensor should be stored in a chamber at the temperature of -40±3°C without loading for 168±4 hours. After

removing from the chamber, the rotary position sensor should be kept in the dry box for 24 +8/-0 hours.

The adjustment rotor should be continuously rotated within ±160° of effective electrical rotational angle, at the rate of one cycle for

6 seconds for 1 Million cycles under the condition of +25±2°C of temperature without loading.

10 Rotational Life

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

Packaging

■ Minimum Quantity

Minimum Quantity (pcs.)

Part Number

Ammo Pack

Magazine

—

Bulk

1000

500

—

Tray

—

1000

—

ø180mm reel

3000

2000

2500

1500

1000

500

250

500

—

ø330mm reel

12000

—

PVZ2A

PVZ2K/R

PVA2

—

8000

—

PVZ3A

PVZ3G

PVZ3K/R

PVG3A/G

PVG3K

PVM4

—

500

100

3000

—

PVF2A

PVG5A

PVG5H

PV32

—

100

—

PV12

—

1000

—

PV36W

PV36Y

PV36X

PV36Z/P

PV37Y/Z

PV37W/X/P

SV01A

SV01L

—

1000

—

1000

—

1000

—

SV21

■ Dimensions of Reel

PVZ2A/PVA2/PVZ3A/PVZ3G/PVF2

PVZ2K/PVZ2R/PVZ3K/PVZ3R/PVM4/PVG3/PVG5H

13.0±0.5 Dia.

21.0±0.8 Dia.

13.0±0.5 Dia.

2.0±0.5

21.0±0.8 Dia.

9.0±1.0

13.0±1.0

17.0±1.0

13.0±1.0

178±2 Dia.

(in mm)

PVG5A

SV01

13.0±0.5 Dia.

2.0±0.5

21.0±0.8 Dia.

25.5±1.0

29.5±1.0

17.0±1.0

19.4±1.0

330±2 Dia.

178.0±2.0 Dia.

(in mm)

Continued on the following page.

• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

!Note

R50E.pdf

sales representatives or product engineers before ordering.

Packaging

Continued from the preceding page.

■ Dimensions of Plastic Tape

PVG5A

2.0±0.1

+0.1

12.0±0.2

4.0±0.1 1.5

Dia.

–0

Across a – a'

Tape feeding direction

Part Number

4.3±0.2

5.4±0.2

5.4±0.1

0.4±0.1

PVG5A

(in mm)

PVG3K

SV01

3.5

4.0

4.0±0.1

2.0±0.1

0.4±0.05

2.8±0.1

0.3±0.1

+0.1

-0

2.0±0.05

1.5

Dia.

+0.1

-0

1.5

Dia.

8.0±0.1

Across a-a'

11.4

Across a-a'

4.0±0.1

16.0

Tape feeding direction

Tolerance: ±0.1

Tape feeding direction

(

)

in mm

(in mm)

■ Dimensions of Radial Taping

PV37Y

PV37Z

12.7±1.0

0±2.0

6.4

0±2.0

6.4

3–0.4±0.1 Dia

3−0.4±0.1 Dia

#3#2#1

4.0±0.1 Dia.

6.35±0.70

2.5

6.35±0.70

2.5

12.7±0.3

2.5±0.5

Across A-A'

Tolerance : ±0.3

Across A-A'

(

)

(

)

in mm

Across B-B'

in mm

Across B-B'

Continued on the following page.

SV01A103CEA01 [MURATA]

相关型号：

SV01A103CEA01B00

SV01A103CEA01R00

SV01A103CEA01T00

SV01A103CEA11B00

SV01A103CEA11R00

SV01A103CEA11T00

SV01AA100JAA

SV01AA100KAA

SV01AA100MAA

SV01AA101JAA

SV01AA101JBA

SV01AA101KAA