MX29F002BTI-90 [Macronix]
2M-BIT [256K x 8] CMOS FLASH MEMORY; 2M- BIT [ 256K ×8 ] CMOS FLASH MEMORY型号: | MX29F002BTI-90 |
厂家: | MACRONIX INTERNATIONAL |
描述: | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
文件: | 总49页 (文件大小:910K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MX29F002/002N
2M-BIT [256K x 8] CMOS FLASH MEMORY
FEATURES
•
•
•
262,144x 8 only
Fast access time: 55/70/90/120ns
Lowpowerconsumption
-Datapolling&Togglebitfordetectionofprogramand
erase cycle completion.
Sector protection
•
- 30mA maximum active current(5MHz)
- 1uA typical standby current
Programming and erasing voltage 5V ± 10%
Command register architecture
- Hardware method to disable any combination of
sectors from program or erase operations
- Sector protect/unprotect for 5V only system or 5V/
12V system
•
•
- Byte Programming (7us typical)
- Sector Erase (16K-Byte x1, 8K-Byte x 2, 32K-Byte
x1, and 64K-Byte x 3)
Auto Erase (chip & sector) and Auto Program
-Automaticallyeraseanycombinationofsectorsorthe
whole chip with Erase Suspend capability.
-Automaticallyprogramsandverifiesdataatspecified
address
•
•
•
100,000minimumerase/programcycles
Latch-up protected to 100mA from -1 to VCC+1V
Boot Code Sector Architecture
- T = Top Boot Sector
•
- B = Bottom Boot Sector
•
HardwareRESETpin(onlyfor29F002T/B)
- Resets internal state machine to read mode
Low VCC write inhibit is equal to or less than 3.2V
Package type:
•
•
•
•
Erase Suspend/Erase Resume
- Suspends an erase operation to read data from, or
programdatato,asectorthatisnotbeingerased,then
resumes the erase operation.
- 32-pin PDIP
- 32-pin PLCC
- 32-pin TSOP (Type 1)
20 years data retention
Status Reply
•
GENERAL DESCRIPTION
MXIC'sFlashtechnologyreliablystoresmemorycontents
even after 100,000 erase and program cycles. The MXIC
cell is designed to optimize the erase and programming
mechanisms. In addition, the combination of advanced
tunnel oxide processing and low internal electric fields for
erase and programming operations produces reliable
cycling. The MX29F002T/B uses a 5.0V ± 10% VCC
supply to perform the High Reliability Erase and auto
Program/Erase algorithms.
The MX29F002T/B is a 2-mega bit Flash memory organ-
ized as 256K bytes of 8 bits only. MXIC's Flash memories
offer the most cost-effective and reliable read/write non-
volatile random access memory. The MX29F002T/B is
packaged in 32-pin PDIP,PLCC and 32-pin TSOP(I). It is
designedtobereprogrammedanderasedin-systemorin-
standard EPROM programmers.
ThestandardMX29F002T/Boffersaccesstimeasfastas
55ns, allowing operation of high-speed microprocessors
without wait states. To eliminate bus contention, the
MX29F002T/B has separate chip enable (CE) and output
enable (OE) controls.
Thehighestdegreeoflatch-upprotectionisachievedwith
MXIC's proprietary non-epi process. Latch-up protection
is proved for stresses up to 100 milliamps on address and
data pin from -1V to VCC + 1V.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29F002T/B uses a command register to manage this
functionality. Thecommandregisterallowsfor100%TTL
level control inputs and fixed power supply levels during
erase and programming, while maintaining maximum
EPROM compatibility.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
1
MX29F002/002N
PIN CONFIGURATIONS
32 PDIP
32 TSOP (TYPE 1)
NC on MX29F002NT/B
VCC
WE
A17
A14
A13
A8
RESET
A16
A15
A12
A7
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
1
A11
A9
1
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
GND
Q2
Q1
Q0
A0
2
2
3
A8
A13
A14
A17
WE
3
4
4
5
5
6
7
A6
6
VCC
RESET
A16
A15
A12
A7
8
MX29F002T/B
A9
A5
7
(NC on MX29F002NT/B)
9
10
11
12
13
14
15
16
A11
OE
A10
CE
A4
8
A3
9
A2
10
11
12
13
14
15
16
A6
A1
A1
A5
A2
Q7
A4
A3
A0
Q6
Q0
Q5
Q1
Q4
Q2
(NORMAL TYPE)
Q3
GND
32 PLCC
SECTOR STRUCTURE
NC on MX29F002NT/B
A 1 7 ~ A 0
3 F F F F H
1 6 K - B Y T E
( B O O T S E C T O R )
3 B F F F H
3 9 F F F H
4
5
1
32
30
29
A7
A6
A5
A4
A3
A2
A1
A0
Q0
A14
A13
A8
8
8
K - B Y T E
K - B Y T E
3 7 F F F H
2 F F F F H
1 F F F F H
A9
3 2 K - B Y T E
6 4 K - B Y T E
6 4 K - B Y T E
6 4 K - B Y T E
9
MX29F002T/B
25
A11
OE
A10
CE
Q7
0 F F F F H
0 0 0 0 0 H
13
14
21
17
20
MX29F002T Sector Architecture
A 1 7 ~ A 0
PIN DESCRIPTION
3 F F F F H
2 F F F F H
1 F F F F H
0 F F F F H
6 4 K - B Y T E
6 4 K - B Y T E
SYMBOL
A0~A17
Q0~Q7
CE
PIN NAME
Address Input
6 4 K - B Y T E
3 2 K - B Y T E
Data Input/Output
Chip Enable Input
Write Enable Input
0 7 F F F H
0 5 F F F H
0 3 F F F H
0 0 0 0 0 H
WE
8
8
K - B Y T E
K - B Y T E
RESET
OE
Hardware Reset Pin/Sector Protect Unlock
Output Enable Input
1 6 K - B Y T E
( B O O T S E C T O R )
VCC
Power Supply Pin (+5V)
Ground Pin
GND
MX29F002B Sector Architecture
REV. 1.1, JUN. 14, 2001
P/N: PM0547
2
MX29F002/002N
BLOCK DIAGRAM
WRITE
CONTROL
INPUT
PROGRAM/ERASE
STATE
MACHINE
(WSM)
WE
OE
HIGH VOLTAGE
LOGIC
WP
RESET
STATE
MX29F002
FLASH
REGISTER
ADDRESS
LATCH
ARRAY
ARRAY
A0~A17
AND
SOURCE
HV
BUFFER
Y-PASS GATE
COMMAND
DATA
DECODER
PGM
DATA
HV
SENSE
AMPLIFIER
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
I/O BUFFER
Q0-Q7
REV. 1.1, JUN. 14, 2001
P/N: PM0547
3
MX29F002/002N
AUTOMATIC ERASE ALGORITHM
AUTOMATIC PROGRAMMING
The MX29F002T/B is byte programmable using the
Automatic Programming algorithm. The Automatic
Programming algorithm does not require the system to
time out or verify the data programmed. The typical
chip programming time of the MX29F002T/B at room
temperature is less than 3.5 seconds.
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using stand-
ard microprocessor write timings. The device will
automatically pre-program and verify the entire array.
Then the device automatically times the erase pulse
width, verifies the erase, and counts the number of
sequences. A status bit similar to DATA polling and
status bit toggling between consecutive read cycles
provides feedback to the user as to the status of the
programming operation.
AUTOMATIC CHIP ERASE
Typical erasure at room temperature is accomplished
in less than 3 seconds. The device is erased using
the Automatic Erase algorithm. The Automatic Erase
algorithm automatically programs the entire array prior
to electrical erase. The timing and verification of
electrical erase are internally controlled by the device.
Commands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as inputs to an internal state-machine
which controls the erase and programming circuitry.
During write cycles, the command register internally
latches address and data needed for the programming
and erase operations. During a system write cycle,
addresses are latched on the falling edge, and data
are latched on the rising edge of WE .
AUTOMATIC SECTOR ERASE
The MX29F002T/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. Sector erase modes allow
sectors of the array to be erased in one erase cycle. The
Automatic Sector Erase algorithm automatically pro-
grams the specified sector(s) prior to electrical erase.
The timing and verification of electrical erase are inter-
nally controlled by the device.
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, relia-
bility, and cost effectiveness. The MX29F002T/B electri-
cally erases all bits simultaneously using Fowler-Nord-
heim tunneling. The bytes are programmed one byte at
a time using the EPROM programming mechanism of hot
electron injection.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write a program set-up commands include
2 unlock write cycle and A0H and a program command
(program data and address). The device automatically
times the programming pulse width, verifies the pro-
gram, and counts the number of sequences. A status
bit similar to DATA polling and a status bit toggling
between consecutive read cycles, provides feedback
to the user as to the status of the programming
operation.
Duringaprogramcycle, thestate-machinewillcontrolthe
program sequences and command register will not re-
spond to any command set. During a Sector Erase cycle,
thecommandregisterwillonlyrespondtoEraseSuspend
command. After Erase Suspend is completed, the device
stays in read mode. After the state machine has com-
pleted its task, it will allow the command register to
respond to its full command set.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
4
MX29F002/002N
TABLE1. SOFTWARE COMMAND DEFINITIONS
First Bus
Cycle
Second Bus
Cycle
Third Bus
Cycle
Fourth Bus
Cycle
Fifth Bus
Cycle
Sixth Bus
Cycle
Command
Bus
Cycle Addr Data
XXXH F0H
RA RD
Addr Data
Addr Data
Addr Data
Addr Data Addr Data
Reset
1
Read
1
Read Silicon ID
Sector Protect
Verification
4
4
555H AAH 2AAH 55H
555H AAH 2AAH 55H
555H 90H
555H 90H
ADI DDI
(SA) 00H
(X02H) 01H
Porgram
4
6
6
1
1
6
555H AAH 2AAH 55H
555H AAH 2AAH 55H
555H AAH 2AAH 55H
XXXH B0H
555H A0H
555H 80H
555H 80H
PA
555H AAH 2AAH
555H AAH 2AAH 55H SA 30H
PD
Chip Erase
55H 555H 10H
Sector Erase
Sector Erase Suspend
Sector Erase Resume
Unlock for sector
protect/unprotect
XXXH 30H
555H AAH 2AAH 55H
555H 80H
555H AAH
2AAH 55H 555H 20H
Note:
1. ADI = Address of Device identifier; A1=0,A0 =0 for manufacture code,A1=0, A0 =1 for device code (Refer to Table 3).
DDI = Data of Device identifier : C2H for manufacture code, 00B0h/0034h for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2. PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address to the sector to be erased.
3.The system should generate the following address patterns: 555H or 2AAH to Address A0~A10. Address bit A11~A17=X=Don't
care for all address commands except for Program Address (PA) and Sector Address (SA). Write Sequence may be initiated
with A11~A17 in either state.
4.For Sector Protect Verification Operation : If read out data is 01H, it means the sector has been protected. If read out data is 00H,
it means the sector is still not being protected.
COMMAND DEFINITIONS
sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the
Sector Erase operation is in progress. Either of the two
reset command sequences will reset the device(when
applicable).
Device operations are selected by writing specific ad-
dress and data sequences into the command register.
Writing incorrect address and data values or writing them
in the improper sequence will reset the device to the read
mode. Table 1 defines the valid register command
REV. 1.1, JUN. 14, 2001
P/N: PM0547
5
MX29F002/002N
TABLE 2. MX29F002T/B BUS OPERATION
Pins
CE
L
OE
L
WE
H
A0
L
A1
L
A6
X
A9
Q0~Q7
C2H
Mode
Read Silicon ID
Manfacturer Code(1)
Read Silicon ID
Device Code(1)
Read
VID(2)
L
L
H
H
L
X
VID(2)
B0h/34h
L
H
L
L
L
L
X
H
X
H
L
A0
X
A1
X
A6
X
A9
X
DOUT
HIGH Z
HIGH Z
DIN(3)
X
Standby
Output Disable
Write
H
X
X
X
X
H
A0
X
A1
X
A6
L
A9
Sector Protect with 12V
system(6)
VID(2)
L
VID(2)
Chip Unprotect with 12V
system(6)
L
L
L
L
L
X
VID(2)
L
H
L
X
X
X
X
X
X
X
H
X
X
H
X
H
X
L
VID(2)
VID(2)
H
X
Code(5)
X
Verify Sector Protect
with 12V system
L
H
H
L
Sector Protect without 12V
system (6)
Chip Unprotect without 12V
system (6)
L
H
X
X
H
X
Verify Sector Protect/Unprotect
without 12V system (7)
Reset
H
X
H
Code(5)
HIGH Z
X
X
NOTES:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table 1.
2. VID is the Silicon-ID-Read high voltage, 11.5V to 12.5V.
3. Refer to Table 1 for valid Data-In during a write operation.
4. X can be VIL or VIH.
5. Code=00H means unprotected.
Code=01H means protected.
A17~A13=Sector address for sector protect.
6. Refer to sector protect/unprotect algorithm and waveform.
Must issue "unlock for sector protect/unprotect" command before "sector protect/unprotect without 12V system" command.
7. The "verify sector protect/unprotect without 12V sysytem" is only following "Sector protect/unprotect without 12V system" com-
mand.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
6
MX29F002/002N
READ/RESET COMMAND
SET-UPAUTOMATICCHIP/SECTORERASE
COMMANDS
The read or reset operation is initiated by writing the read/
reset command sequence into the command register.
Microprocessor read cycles retrieve array data. The
device remains enabled for reads until the command
register contents are altered.
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cycles
are then followed by the chip erase command 10H.
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid command
must then be written to place the device in the desired
state.
The Automatic Chip Erase does not require the device to
be entirely pre-programmed prior to executing the Auto-
matic Chip Erase. Upon executing the Automatic Chip
Erase,thedevicewillautomaticallyprogramandverifythe
entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero
pattern, a self-timed chip erase and verify begin. The
erase and verify operations are completed when the data
on Q7 is "1" at which time the device returns to the Read
mode. The system is not required to provide any control
or timing during these operations.
SILICON-ID-READ COMMAND
Flash memories are intended for use in applications
where the local CPU alters memory contents. As such,
manufacturer and device codes must be accessible while
the device resides in the target system. PROM
programmers typically access signature codes by raising
A9 to a high voltage. However, multiplexing high voltage
onto address lines is not generally desired system design
practice.
WhenusingtheAutomaticChipErasealgorithm,notethat
the erase automatically terminates when adequate erase
marginhasbeenachievedforthememoryarray(noerase
verify command is required).
The MX29F002T/B contains a Silicon-ID-Read operation
tosupplementtraditionalPROMprogrammingmethodol-
ogy. The operation is initiated by writing the read silicon
ID command sequence into the command register. Fol-
lowing the command write, a read cycle with A1=VIL,
A0=VIL retrieves the manufacturer code of C2H. A read
cyclewithA1=VIL,A0=VIHreturnsthedevicecodeofB0h
for MX29F002T, 34h for MX29F002B.
If the Erase operation was unsuccessful, the data on Q5
is "1"(see Table 4), indicating the erase operation exceed
internal timing limit.
The automatic erase begins on the rising edge of the last
WE pulse in the command sequence and terminates
when the data on Q7 is "1" and the data on Q6 stops
togglingfortwoconsecutivereadcycles,atwhichtimethe
device returns to the Read mode.
TABLE 3. EXPANDED SILICON ID CODE
Pins A0 A1 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Code(Hex)Code
Manufacture code
Device code
VIL VIL
VIH VIL
1
1
1
0
0
1
0
1
0
0
0
0
1
0
0
0
C2H
B0h
for MX29F002T
Device code
VIH VIL
0
0
1
1
0
1
0
0
34h
for MX29F002B
Sector Protection
Verification
X
X
VIH
VIH
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
01H (Protected)
00H (Unprotected)
REV. 1.1, JUN. 14, 2001
P/N: PM0547
7
MX29F002/002N
selected are loaded into internal register on the sixth
falling edge of WE. Each successive sector load cycle
started by the falling edge of WE must begin within 30us
from the rising edge of the preceding WE. Otherwise, the
loading period ends and internal auto sector erase cycle
starts. (Monitor Q3 to determine if the sector erase timer
window is still open, see section Q3, Sector Erase Timer.)
Any command other than Sector Erase (30H) or Erase
Suspend (BOH) during the time-out period resets the
device to read mode.
SET-UP AUTOMATIC SECTOR ERASE
COMMANDS
The Automatic Sector Erase does not require the device
to be entirely pre-programmed prior to executing the
AutomaticSet-upSectorErasecommandandAutomatic
Sector Erase command. Upon executing the Automatic
Sector Erase command, the device will automatically
program and verify the sector(s) memory for an all-zero
datapattern. Thesystemdoesnotrequire toprovideany
control or timing during these operations.
ERASE SUSPEND
When the sector(s) is automatically verified to contain an
all-zeropattern,aself-timedsectorerase and verification
begin. The erase and verification operations are com-
plete when the data on Q7 is "1" and the data on Q6 stops
togglingfortwoconsecutivereadcycles,atwhichtimethe
device returns to the Read mode. The system does not
required to provide any control or timing during these
operations.
This command is only valid while the state machine is
executingAutomaticSectorEraseoperation,andtherefore
will only be responded during Automatic Sector Erase
operation. Writing the Erase Suspend command during
the Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation. After
this command has been executed, the command register
will initiate erase suspend mode. The state machine will
return to read mode automatically after suspend is ready.
At this time, state machine only allows the command
register to respond to the Read Memory Array, Erase
Resume and Program commands. The system can
determine the status of the program operation using the
Q7 or Q6 status bits, just as in the standard program
operation. Afteranerase-suspendendprogramoperation
is complete, the system can once again read array data
withinnon-suspendedsectors.
When using the Automatic Sector Erase algorithm, note
that the erase automatically terminates when adequate
erasemarginhasbeenachievedforthememoryarray(no
erase verify command is required). Sector erase is a six-
bus cycle operation. There are two "unlock" write cycles.
These are followed by writing the set-up command-80H.
Two more "unlock" write cycles are then followed by the
sector erase command-30H. The sector address is
latchedonthefallingedgeofWE,whilethecommand(data)
is latched on the rising edge of WE. Sector addresses
REV. 1.1, JUN. 14, 2001
P/N: PM0547
8
MX29F002/002N
Table 4. Write Operation Status
Status
Q7
Q6
Q5
Q3
Q2
Note1
Note2
Byte Program in Auto Program Algorithm
Q7 Toggle
0
0
0
N/A No Toggle
Auto Erase Algorithm
0
1
Toggle
No
1
Toggle
Toggle
Erase Suspend Read
N/A
In Progress
(Erase Suspended Sector)
Erase Suspend Read
Toggle
Erase Suspended Mode
Data Data Data Data
Data
N/A
(Non-Erase Suspended Sector)
Erase Suspend Program
Q7 Toggle
Q7 Toggle
0
1
1
1
N/A
Byte Program in Auto Program Algorithm
N/A No Toggle
Exceeded Auto Erase Algorithm
0
Toggle
1
Toggle
N/A
Time Limits Erase Suspend Program
Q7 Toggle
N/A
Note:
1. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
2. Q5 switches to '1' when an Auto Program or Auto Erase operation has exceeded the maximum timing limits.
See "Q5:Exceeded Timing Limits " for more information.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
9
MX29F002/002N
WhiletheAutomaticErasealgorithmisinoperation,Q7will
read "0" until the erase operation is competed. Upon
completionoftheeraseoperation,thedataonQ7willread
"1". The Data Polling feature is valid after the rising edge
of the sixth WE pulse of six write pulse sequences for
automatic chip/sector erase.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. EraseResumewillnothaveanyeffectinallother
conditions.Another Erase Suspend command can be
written after the chip has resumed erasing.
The Data Polling feature is active during Automatic
Program/Erase algorithm or sector erase time-out.(see
section Q3 Sector Erase Timer)
SET-UP
AUTOMATIC
PROGRAM
COMMANDS
Q6:Toggle BIT I
To initiate Automatic Program mode, a three-cycle
command sequence is required. There are two "unlock"
write cycles. These are followed by writing the Automatic
Program command A0H.
The MX29F002T/B features a "Toggle Bit" as a method to
indicate to the host system that the Auto Program/Erase
algorithms are either in progress or completed.
Once the Automatic Program command is initiated, the
nextWEpulsecausesatransitiontoanactiveprogramming
operation. Addressesarelatchedonthefallingedge,and
data are internally latched on the rising edge of the WE
pulse. TherisingedgeofWEalsobeginstheprogramming
operation. Thesystemdoesnotrequiretoprovidefurther
controls or timings. The device will automatically provide
an adequate internally generated program pulse and
verify margin.
DuringanAutomaticProgramorErasealgorithmoperation,
successive read cycles to any address cause Q6 to
toggle. ThesystemmayuseeitherOEorCEtocontrolthe
read cycles. When the operation is complete, Q6 stops
toggling.
After an erase command sequence is written, if all sectors
selectedforerasingareprotected,Q6togglesand returns
to reading array data. If not all selected sectors are
protected, the Automatic Erase algorithm erases the
unprotectedsectors,andignorestheselectedsectorsthat
are protected.
If the program opetation was unsuccessful, the data on
Q5is"1",indicatingtheprogramoperationexceedinternal
timing limit. The automatic programming operation is
completed when the data read on Q6 stops toggling for
two consecutive read cycles and the data on Q7 and Q6
are equivalent to data written to these two bits, at which
time the device returns to the Read mode(no program
verify command is required).
The system can use Q6 and Q2 together to determine
whetherasectorisactivelyerasingoriserasesuspended.
When the device is actively erasing (that is, the Automatic
Erase algorithm is in progress), Q6 toggling. When the
deviceenterstheEraseSuspendmode,Q6stopstoggling.
However, the system must also use Q2 to determine
which sectors are erasing or erase-suspended.
Alternatively, the system can use Q7(see the subsection
on Q7:Data Polling).
WRITE OPERATION STATUS
DATA POLLING-Q7
TheMX29F002T/BalsofeaturesDataPollingasamethod
toindicatetothehostsystemthattheAutomaticProgram
or Erase algorithms are either in progress or completed.
If a program address falls within a protected sector, Q6
toggles forapproximately2us aftertheprogramcommand
sequence is written, then returns to reading array data.
WhiletheAutomaticProgrammingalgorithmisinoperation,
anattempttoreadthedevicewillproducethecomplement
dataofthedatalastwrittentoQ7. Uponcompletionofthe
Automatic Program Algorithm an attempt to read the
device will produce the true data last written to Q7. The
Data Polling feature is valid after the rising edge of the
fourth WE pulse of the four write pulse sequences for
automaticprogram.
Q6alsotogglesduringtheerase-suspend-programmode,
andstopstogglingoncetheAutomaticProgramalgorithm
is complete.
The Write Operation Status table shows the outputs for
Toggle Bit I on Q6. Refer to the toggle bit algorithmg.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
10
MX29F002/002N
describedinthepreviousparagraph. Alternatively, itmay
choose to perform other system tasks. In this case, the
system must start at the beginning of the algorithm when
itreturnstodeterminethestatusoftheoperation(topofthe
toggle bit algorithm flow chart).
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whetheraparticularsectorisactivelyeraseing(thatis,the
Automatic Erase alorithm is in process), or whether that
sector is erase-suspended. Toggle Bit I is valid after the
risingedgeofthefinalWEpulseinthecommandsequence.
Q5
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE or CE to control the read
cycles.) But Q2 cannot distinguish whether the sector is
activelyerasingoriserase-suspended. Q6,bycomparison,
indicates whether the device is actively erasing, or is in
Erase Suspend, but cannot distinguish which sectors are
selected for erasure. Thus, both status bits are required
for sectors and mode information. Refer to Table 4 to
compare outputs for Q2 and Q6.
Exceeded Timing Limits
Q5willindicateiftheprogramorerasetimehasexceeded
the specified limits(internal pulse count). Under these
conditions Q5 will produce a "1". This time-out condition
which indicates that the program or erase cycle was not
successfully completed. Data Polling and Toggle Bit are
the only operating functions of the device under this
condition.
If this time-out condition occurs during sector erase
operation, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. Thedevicemustberesettouseothersectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence.
This allows the system to continue to use the other active
sectors in the device.
Reading Toggle Bits Q6/ Q2
Refertothetogglebitalgorithmforthefollowingdiscussion.
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
wouldcomparethenewvalueofthetogglebitwiththefirst.
If the toggle bit is not toggling, the device has completed
the program or erase operation. The system can read
array data on Q7-Q0 on the following read cycle.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or
combination of sectors are bad.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system
also should note whether the value of Q5 is high (see the
section on Q5). If it is, the system should then determine
againwhetherthetogglebitistoggling,sincethetogglebit
may have stopped toggling just as Q5 went high. If the
togglebitisnolongertoggling,thedevicehassuccessfuly
completed the program or erase operation. If it is still
toggling, the device did not complete the operation
successfully,andthesystemmustwritetheresetcommand
to return to reading array data.
If this time-out condition occurs during the byte
programming operation, it specifies that the entire sector
containing that byte is bad and this sector maynot be
reused, (other sectors are still functional and can be
reused).
The Q5 time-out condition may also appear if a user tries
to program a non blank location without erasing. In this
case the device locks out and never completes the
AutomaticAlgorithmoperation. Hence,thesystemnever
reads a valid data on Q7 bit and Q6 never stops toggling.
Once the Device has exceeded timing limits, the Q5 bit
will indicate a "1". Please note that this is not a device
failure condition since the device was incorrectly used.
Theremainingscenarioisthatsysteminitiallydetermines
that the toggle bit is toggling and Q5 has not gone high.
ThesystemmaycontinuetomonitorthetogglebitandQ5
throughsuccessivereadcycles,determiningthestatusas
REV. 1.1, JUN. 14, 2001
P/N: PM0547
11
MX29F002/002N
Q3
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE = VIL, CE =
VIHorWE=VIH. ToinitiateawritecycleCEandWEmust
be a logical zero while OE is a logical one.
Sector Erase Timer
After the completion of the initial sector erase command
sequence th sector erase time-out will begin. Q3 will
remainlowuntilthetime-outiscomplete. DataPollingand
ToggleBitarevalidaftertheinitialsectorerasecommand
sequence.
POWER SUPPLY DECOUPLING
In order to reduce power switching effect, each device
should havea0.1uFceramiccapacitorconnectedbetween
its VCC and GND.
If Data Polling or the Toggle Bit indicates the device has
beenwrittenwithavaliderasecommand,Q3maybeused
to determine if the sector erase timer window is still open.
If Q3 is high ("1") the internally controlled erase cycle has
begun; attempts to write subsequent commands to the
devicewillbeignoreduntiltheeraseoperationiscompleted
asindicatedbyDataPollingorToggleBit. IfQ3islow("0"),
the device will accept additional sector erase commands.
To insure the command has been accepted, the system
software should check the status of Q3 prior to and
followingeachsubsequentsectorerasecommand. If Q3
werehighonthesecondstatuscheck, thecommandmay
not have been accepted.
SECTOR PROTECTION WITH 12V SYSTEM
The MX29F002T/B features hardware sector protection.
Thisfeaturewilldisablebothprogramanderaseoperations
for these sectors protected. To activate this mode, the
programming equipment must force VID on address pin
A9 and control pin OE, (suggest VID = 12V) A6 = VIL and
CE = VIL.(see Table 2) Programming of the protection
circuitry begins on the falling edge of the WE pulse and is
terminated on the rising edge. Please refer to sector
protect algorithm and waveform.
To verify programming of the protection circuitry, the
programming equipment must force VID on address pin
A9 ( with CE and OE at VIL and WE at VIH. When A1=1,
it will produce a logical "1" code at device output Q0 for a
protected sector. Otherwise the device will produce 00H
for the unprotected sector. In this mode, the
addresses,exceptforA1,arein"don'tcare"state. Address
locationswithA1=VILarereservedtoreadmanufacturer
and device codes.(Read Silicon ID)
DATA PROTECTION
TheMX29F002T/B isdesignedtoofferprotectionagainst
accidental erasure or programming caused by spurious
systemlevelsignalsthatmayexistduringpowertransition.
Duringpowerupthedeviceautomaticallyresetsthestate
machine in the Read mode. In addition, with its control
register architecture, alteration of the memory contents
only occurs after successful completion of specific
command sequences. The device also incorporates
several features to prevent inadvertent write cycles
resulting from VCC power-up and power-down transition
or system noise.
It is also possible to determine if the sector is protected in
the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
WRITE PULSE "GLITCH" PROTECTION
Noisepulsesoflessthan5ns(typical)onCEorWEwillnot
initiate a write cycle.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
12
MX29F002/002N
Temporary Sector Unprotect Operation (For 29F002T/B only)
Start
RESET = VID (Note 1)
Perform Erase or Program Operation
Operation Completed
RESET = VIH
Temporary Sector Unprotect Completed(Note 2)
Note :
1. All protected sectors are temporary unprotected.
VID=11.5V~12.5V
2. All previously protected sectors are protected again.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
13
MX29F002/002N
TEMPORARY SECTOR UNPROTECT
ParameterStd. Description
Test Setup AllSpeedOptions Unit
tVIDR
tRSP
VID Rise and Fall Time (See Note)
RESET Setup Time for Temporary Sector Unprotect
Min
Min
500
4
ns
us
Note:
Not 100% tested
Temporary Sector Unprotect Timing Diagram(For 29F002T/B only)
12V
RESET
0 or 5V
0 or 5V
Program or Erase Command Sequence
tVIDR
tVIDR
CE
WE
tRSP
REV. 1.1, JUN. 14, 2001
P/N: PM0547
14
MX29F002/002N
AC CHARACTERISTICS
ParameterStd Description
Test Setup All Speed Options Unit
tREADY
RESET PIN Low (Not During Automatic Algorithms)
MAX
500
ns
to Read or Write (See Note)
tRP1
tRP2
tRH
RESET Pulse Width (During Automatic Algorithms)
MIN
10
500
0
us
ns
ns
RESET Pulse Width (NOT During Automatic Algorithms) MIN
RESET High Time Before Read(See Note) MIN
Note:
Not 100% tested
RESET TIMING WAVFORM (For 29F002T/B only)
CE, OE
tRH
RESET
tRP2
tReady
Reset Timing NOT during Automatic Algorithms
RESET
tRP1
Reset Timing during Automatic Algorithms
REV. 1.1, JUN. 14, 2001
P/N: PM0547
15
MX29F002/002N
CHIP UNPROTECT WITH 12V SYSTEM
ABSOLUTE MAXIMUM RATINGS
TheMX29F002T/Balsofeaturesthechipunprotectmode,
so that all sectors are unprotected after chip unprotect is
completed to incorporate any changes in the code. It is
recommendedtoprotectallsectorsbeforeactivatingchip
unprotect mode.
RATING
VALUE
Ambient Operating Temperature 0oC to 70oC
Storage Temperature
Applied Input Voltage
Applied Output Voltage
VCC to Ground Potential
A9
-65oC to 125oC
-0.5V to 7.0V
-0.5V to 7.0V
-0.5V to 7.0V
-0.5V to 13.5V
To activate this mode, the programming equipment must
force VID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.(see
Table 2) Refer to chip unprotect algorithm and waveform
for the chip unprotect algorithm. The unprotection
mechanismbeginsonthefallingedgeoftheWEpulseand
is terminated on the rising edge.
NOTICE:
Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress
rating only and functional operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended
period may affect reliability.
It is also possible to determine if the chip is unprotected in
the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs(Q0-Q7) for an unprotected sector. It
is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
NOTICE:
Specifications contained within the following tables are subject to
change.
SECTOR PROTECTION WITHOUT 12V
SYSTEM
The MX29F002T/B also feature a hardware sector
protectionmethodinasystemwithout12Vpowersuppply.
The programming equipment do not need to supply 12
volts to protect sectors. The details are shown in sector
protect algorithm and waveform.
CHIP UNPROTECT WITHOUT 12V SYSTEM
The MX29F002T/B also feature a hardware chip
unprotection method in a system without 12V power
supply. The programming equipment do not need to
supply 12 volts to unprotect all sectors. The details are
shown in chip unprotect algorithm and waveform.
POWER-UP SEQUENCE
The MX29F002T/B powers up in the Read only mode. In
addition, the memory contents may only be altered after
successfulcompletionofatwo-stepcommandsequence.
Vpp and Vcc power up sequence is not required.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
16
MX29F002/002N
DC/AC Operating Conditions for Read/Programming/Erase Operation
MX29F002/002N
-70 -90
0oC to 70oC 0oC to 70oC 0oC to 70oC
-55
-12
0oC to 70oC
OperatingTemperature
Vcc Power Supply
Commercial
Industrial
-40oCto85oC -40oCto85oC -40oCto85oC
5V±5%
5V±10%
5V±10%
5V±10%
CAPACITANCE TA = 25oC, f = 1.0 MHz
SYMBOL
CIN1
PARAMETER
MIN.
TYP
MAX.
8
UNIT
pF
CONDITIONS
VIN = 0V
Input Capacitance
Control Pin Capacitance
Output Capacitance
CIN2
12
pF
VIN = 0V
COUT
12
pF
VOUT = 0V
READ OPERATION
DC CHARACTERISTICS
SYMBOL
ILI
PARAMETER
MIN.
TYP
MAX.
UNIT
CONDITIONS
Input Leakage Current
Output Leakage Current
Standby VCC current
1(Note 3) uA
VIN = GND to VCC
VOUT = GND to VCC
CE = VIH
ILO
10
1
uA
mA
uA
ISB1
ISB2
ICC1
ICC2
VIL
1
5
CE = VCC + 0.3V
IOUT = 0mA, f=5MHz
IOUT = 0mA, f=10MHz
Operating VCC current
30(Note 4) mA
50
mA
V
Input Low Voltage
-0.3(NOTE 1)
2.0
0.8
VIH
Input High Voltage
VCC + 0.3
0.45
V
VOL
Output Low Voltage
V
IOL = 2.1mA
IOH = -2mA
VOH1
VOH2
Output High Voltage(TTL)
Output High Voltage(CMOS)
2.4
V
VCC-0.4
V
IOH = -100uA,
VCC=VCC MIN
NOTES:
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns.
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. ILI=10uA for Industrial grade.
4. ICC1=45mA for Industrial grade.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
17
MX29F002/002N
AC CHARACTERISTICS
29F002T/B-55
29F002T/B-70
SYMBOL PARAMETER
MIN.
MAX.
55
MIN.
MAX.
70
UNIT CONDITION
tACC
tCE
tOE
tDF
Address to Output Delay
ns
ns
ns
ns
ns
CE=OE=VIL
OE=VIL
CE to Output Delay
55
70
OE to Output Delay
25
30
CE=VIL
OE High to Output Float (Note1)
Address to Output hold
0
0
20
0
0
20
CE=VIL
tOH
CE=OE=VIL
29F002T/B-90
29F002T/B-12
SYMBOL PARAMETER
MIN.
MAX.
90
MIN.
MAX.
120
120
50
UNIT CONDITIONS
tACC
tCE
tOE
tDF
Address to Output Delay
ns
ns
ns
ns
ns
CE=OE=VIL
OE=VIL
CE to Output Delay
90
OE to Output Delay
40
CE=VIL
OE High to Output Float (Note1)
Address to Output hold
0
0
30
0
0
30
CE=VIL
tOH
CE=OE=VIL
TEST CONDITIONS:
NOTE:
1. tDF is defined as the time at which the output achieves the
open circuit condition and data is no longer driven.
•
•
Input pulse levels: 0.45V/2.4V for 70ns max., 0V/3V for 55ns
Input rise and fall times: < 10ns for 70ns max.
< 5ns for 55ns
•
Output load:
1 TTL gate + 100pF (Including scope and jig) for 70ns max.
1 TTL gate + 50pF (Including scope and jig) for 55ns speed
grade
•
Reference levels for measuring timing: 0.8V, 2.0V for 70ns
max.
: 1.5V for 55ns
READ TIMING WAVEFORMS
VIH
ADD Valid
A0~17
VIL
tCE
VIH
CE
VIL
VIH
WE
tDF
VIL
tOE
VIH
OE
tACC
VIL
tOH
HIGH Z
HIGH Z
VOH
VOL
DATA
Q0~7
DATA Valid
REV. 1.1, JUN. 14, 2001
P/N: PM0547
18
MX29F002/002N
COMMAND PROGRAMMING/DATA PROGRAMMING/ERASE OPERATION
DC CHARACTERISTICS
SYMBOL
PARAMETER
MIN.
TYP
MAX.
UNIT CONDITIONS
ICC1 (Read)
ICC2
Operating VCC Current
30(Note 5) mA
IOUT=0mA, f=5MHz
IOUT=0mA, F=10MHz
In Programming
50
50
50
mA
mA
mA
mA
ICC3 (Program)
ICC4 (Erase)
ICCES
In Erase
VCC Erase Suspend Current
2
CE=VIH, Erase Suspended
NOTES:
1. VIL min. = -0.6V for pulse width is equal to or less than 20ns.
2. If VIH is over the specified maximum value, programming operation cannot be guranteed.
3. ICCES is specified with the device de-selected. If the device is read during erase suspend mode, current draw is the sum ofICCES
and ICC1 or ICC2.
4. All current are in RMS unless otherwise noted.
5. ICC1(Read)=45mA for Industrial Grade.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
19
MX29F002/002N
AC CHARACTERISTICS
29F002T/B-55(NOTE 2)
SYMBOL PARAMETER
MIN.
0
MAX.
UNIT CONDITIONS
tOES
tCWC
tCEP
tCEPH1
tCEPH2
tAS
OE setup time
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
s
Command programming cycle
WE programming pulse width
WE programming pluse width High
WE programming pluse width High
Address setup time
70
45
20
20
0
tAH
Address hold time
45
20
0
tDS
Data setup time
tDH
Data hold time
tCESC
tDF
CE setup time before command write
Output disable time (Note 1)
Total erase time in auto chip erase
Total erase time in auto sector erase
Total programming time in auto verify
(Byte Program time)
0
20
24
8
tAETC
tAETB
tAVT
3(TYP.)
1(TYP.)
7
s
210
us
tBAL
Sector address load time
CE Hold Time
100
0
us
ns
ns
us
us
us
ms
tCH
tCS
CE setup to WE going low
Voltge Transition Time
0
tVLHT
tOESP
tWPP1
tWPP2
4
OE Setup Time to WE Active
Write pulse width for sector protect
Write pulse width for sector unprotect
4
10
12
NOTES:
1.tDF defined as the time at which the output achieves the open circuit condition and data is no longer driven.
2.The test conditin of MX29F002T/B-55 : VCC=5V ± 5%,CL=50pf,VIH/VIL=3.0V/0V
VOH/VOL=1.5V/1.5V,IOL=2mA,IOH=-2mA
TA= 0oC TO 70oC
REV. 1.1, JUN. 14, 2001
P/N: PM0547
20
MX29F002/002N
AC CHARACTERISTICS
29F002T/B-70 29F002T/B-90 29F002T/B-12
SYMBOL PARAMETER
MIN.
0
MAX. MIN.
MAX. MIN.
MAX. UNIT CONDITIONS
tOES
tCWC
tCEP
tCEPH1
tCEPH2
tAS
OE setup time
0
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Command programming cycle
WE programming pulse width
WE programming pluse width High
WE programming pluse width High
Address setup time
70
45
20
20
0
90
120
45
50
20
20
20
20
0
0
tAH
Address hold time
45
30
0
45
50
tDS
Data setup time
45
50
tDH
Data hold time
0
0
tCESC
tDF
CE setup time before command write
Output disable time (Note 1)
Total erase time in auto chip erase
Total erase time in auto sector erase
Total programming time in auto verify
(Byte Program time)
0
0
0
30
40
40
3(TYP.) 24
ns
s
tAETC
tAETB
tAVT
3(TYP.) 24
1(TYP.) 8
3(TYP.) 24
1(TYP.)
7
8
1(TYP.)
7
8
s
7
210
210
210
us
tBAL
Sector address load time
CE Hold Time
100
0
100
0
100
0
us
ns
ns
us
us
us
ms
tCH
tCS
CE setup to WE going low
Voltge Transition Time
0
0
0
tVLHT
tOESP
tWPP1
tWPP2
4
4
4
OE Setup Time to WE Active
Write pulse width for sector protect
Write pulse width for sector unprotect
4
4
4
10
12
10
12
10
12
NOTES:
1. tDF defined as the time at which the output achieves the open circuit condition and data is no longer driven.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
21
MX29F002/002N
SWITCHING TEST CIRCUITS
DEVICE UNDER
TEST
1.6K ohm
+5V
CL
1.2K ohm
DIODES=IN3064
OR EQUIVALENT
CL=100pF Including jig capacitance
CL=50pF for MX29F002T/B-55
SWITCHING TEST WAVEFORMS(I) for speed grade 70ns max.
2.4V
2.0V
0.8V
2.0V
TEST POINTS
0.8V
0.45V
INPUT
OUTPUT
AC TESTING: Inputs are driven at 2.4V for a logic "1" and 0.45V for a logic "0".
Input pulse rise and fall times are equal to or less than 20ns.
SWITCHING TEST WAVEFORMS(II) for speed grade 55ns(MX29F002T/B-55)
3.0V
TEST POINTS
1.5V
1.5V
0V
INPUT
OUTPUT
AC TESTING: Inputs are driven at 3.0V for a logic "1" and 0V for a logic "0".
Input pulse rise and fall times are < 5ns.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
22
MX29F002/002N
COMMAND WRITE TIMING WAVEFORM
VCC
5V
VIH
ADD
ADD Valid
A0~17
VIL
tAH
tAS
VIH
WE
VIL
tOES
tCEPH1
tCEP
tCWC
VIH
VIL
CE
OE
tCS
tCH
tDH
VIH
VIL
tDS
VIH
VIL
DATA
Q0-7
DIN
REV. 1.1, JUN. 14, 2001
P/N: PM0547
23
MX29F002/002N
AUTOMATIC PROGRAMMING TIMING
WAVEFORM
after automatic verification starts. Device outputs DATA
during programming and DATA after programming on
Q7.(Q6 is for toggle bit; see toggle bit, DATA polling,
timing waveform)
Onebytedataisprogrammed. Verifyinfastalgorithmand
additional programming by external control are not re-
quired because these operations are executed automati-
cally by internal control circuit. Programming completion
can be verified by DATA polling and toggle bit checking
AUTOMATIC PROGRAMMING TIMING WAVEFORM
Vcc 5V
A11~A17
ADD Valid
ADD Valid
2AAH
555H
A0~A10
WE
555H
tAS
tCWC
tCEPH1
tAH
tCESC
tAVT
CE
OE
tCEP
tDS tDH
tDF
DATA
DATA
Q0~Q1,Q2
,Q4(Note 1)
Command In
Command In
Command In
Data In
Data In
DATA polling
DATA
Command In
Command In
Command In
Q7
Command #A0H
Command #AAH
Command #55H
tOE
(Q0~Q7)
Notes:
(1). Q6:Toggle bit, Q5:Tin=Timing-limit bit, Q3: Time-out bit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
24
MX29F002/002N
AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Write Program Data/Address
NO
Toggle Bit Checking
Q6 not Toggled
YES
NO
Invalid
Verify Byte Ok
Command
YES
NO
.
Q5 = 1
Reset
Auto Program Completed
YES
Auto Program Exceed
Timing Limit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
25
MX29F002/002N
TOGGLE BIT ALGORITHM
START
Read Q7~Q0
Read Q7~Q0
(Note 1)
NO
Toggle Bit Q6
=Toggle?
YES
NO
Q5=1?
YES
(Note 1,2)
Read Q7~Q0 Twice
Toggle Bit Q6
=Toggle?
YES
Program/Erase Operation Not
Program/Erase Operation Complete
Complete, Write Reset Command
Note:
1. Read toggle bit Q6 twice to determine whether or not it is toggle. See test.
2. Recheck toggle bit Q6 because it may stop toggling as Q5 changes to "1". See test.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
26
MX29F002/002N
AUTOMATIC CHIPE RASETIMING WAVEFORM
All data in chip are erased. External erase verify is not
requiredbecausedatais erasedautomaticallybyinternal
control circuit. Erasure completion can be verified by
DATApollingandtogglebitcheckingafterautomaticerase
starts. Deviceoutputs0duringerasureand1aftererasure
on Q7.(Q6 is for toggle bit; see toggle bit, DATA polling,
timingwaveform)
AUTOMATIC CHIP ERASE TIMING WAVEFORM
Vcc 5V
A11~A17
555H
2AAH
555H
2AAH
555H
A0~A10
WE
555H
tAS
tCWC
tAH
tCEPH1
tAETC
CE
OE
tCEP
tDS tDH
Q0,Q1,
Command In
Command In
Command In
Command In
Command In
Command In
Command In
Q4(Note 1)
DATA polling
Command In
Command In
Command In
Command In
Command In
Q7
Command #80H
Command #AAH
Command #55H
Command #10H
Command #AAH
Command #55H
(Q0~Q7)
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
27
MX29F002/002N
AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
NO
Toggle Bit Checking
Q6 not Toggled
YES
NO
Invalid
DATA Polling
Q7 = 1
Command
YES
NO
.
Q5 = 1
Auto Chip Erase Completed
YES
Reset
Auto Chip Erase Exceed
Timing Limit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
28
MX29F002/002N
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
after automatic erase starts. Device outputs 0 during
erasureand1aftererasureonQ7.(Q6isfortogglebit;see
toggle bit, DATA polling, timing waveform)
SectordataindicatedbyA13toA17 areerased. External
eraseverificationisnotrequiredbecausedataareerased
automatically by internal control circuit. Erasure comple-
tioncanbeverifiedbyDATApollingandtogglebitchecking
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Vcc 5V
Sector
Addressn
Sector
Address0
Sector
Address1
A13~A17
A0~A10
555H
555H
555H
tAS
2AAH
2AAH
tCWC
tAH
WE
CE
tCEPH1
tBAL
tAETB
tCEP
tDS
OE
tDH
Command
In
Command
In
Q0,Q1,
Command
In
Command
Command
In
Command
In
Command
Command
In
In
In
Q4(Note 1)
DATA polling
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Q7
Command #AAH Command #55H Command #80H Command #AAH Command #55H Command #30H
(Q0~Q7)
Command #30H
Command #30H
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
29
MX29F002/002N
AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Sector Address
NO
Toggle Bit Checking
Q6 Toggled ?
Invalid Command
YES
Load Other Sector Addrss If Necessary
(Load Other Sector Address)
NO
Last Sector
to Erase
YES
NO
NO
Time-out Bit
Checking Q3=1 ?
YES
Toggle Bit Checking
Q6 not Toggled
YES
NO
Q5 = 1
DATA Polling
Q7 = 1
YES
Reset
Auto Sector Erase Completed
Auto Sector Erase Exceed
Timing Limit
REV. 1.1, JUN. 14, 2001
P/N: PM0547
30
MX29F002/002N
ERASE SUSPEND/ERASE RESUME FLOWCHART
START
Write Data B0H
NO
Toggle Bit checking Q6
not toggled
YES
Read Array or
Program
Reading or
NO
Programming End
YES
Write Data 30H
Continue Erase
.
.
Another
NO
Erase Suspend ?
YES
REV. 1.1, JUN. 14, 2001
P/N: PM0547
31
MX29F002/002N
TIMING WAVEFORM FOR SECTOR PROTECTION FOR SYSTEM WITH 12V
A1
A6
12V
5V
A9
tVLHT
tVLHT
Verify
12V
5V
OE
tVLHT
tWPP 1
WE
CE
tOESP
Data
01H
F0H
tOE
A17-A13
Sector Address
REV. 1.1, JUN. 14, 2001
P/N: PM0547
32
MX29F002/002N
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITH 12V
A1
12V
5V
A9
A6
tVLHT
Verify
12V
5V
OE
tVLHT
tVLHT
tWPP 2
WE
CE
tOESP
Data
00H
F0H
tOE
REV. 1.1, JUN. 14, 2001
P/N: PM0547
33
MX29F002/002N
SECTOR PROTECTION ALGORITHM FOR SYSTEM WITH 12V
START
Set Up Sector Addr
(A17,A16,A15,A14,A13)
PLSCNT=1
OE=VID,A9=VID,CE=VIL
A6=VIL
Activate WE Pulse
Time Out 10us
Set WE=VIH, CE=OE=VIL
A9 should remain VID
Read from Sector
Addr=SA, A1=1
No
No
Data=01H?
PLSCNT=32?
.
Yes
Device Failed
Yes
Protect Another
Sector?
Remove VID from A9
Write Reset Command
Sector Protection
Complete
REV. 1.1, JUN. 14, 2001
P/N: PM0547
34
MX29F002/002N
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITH 12V
START
Protect All Sectors
PLSCNT=1
Set OE=A9=VID
CE=VIL,A6=1
Activate WE Pulse
Time Out 12ms
Increment
PLSCNT
Set OE=CE=VIL
A9=VID,A1=1
Set Up First Sector Addr
Read Data from Device
No
No
Data=00H?
Yes
PLSCNT=1000?
Increment
Sector Addr
Yes
Device Failed
No
All sectors have
been verified?
Yes
Remove VID from A9
Write Reset Command
Chip Unprotect
Complete
* It is recommended before unprotect the whole chip, all sectors should be protected in advance.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
35
MX29F002/002N
TIMING WAVEFORM FOR SECTOR PROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Don't care
(Note 2)
Data
01H
F0H
tOE
A17-A13
Sector Address
Note1: Must issue "unlock for sector protect/unprotect" command before sector protection
for a system without 12V provided.
Note2: Except F0H
REV. 1.1, JUN. 14, 2001
P/N: PM0547
36
MX29F002/002N
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Don't care
(Note 2)
Data
F0H
00H
tOE
Note1: Must issue "unlock for sector protect/unprotect" command before sector unprotection
for a system without 12V provided.
Note2: Except F0H
REV. 1.1, JUN. 14, 2001
P/N: PM0547
37
MX29F002/002N
SECTOR PROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
PLSCNT=1
Write "unlock for sector protect/unprotect"
Command(Table1)
Set Up Sector Addr
(A17,A16,A15,A14,A13)
OE=VIH,A9=VIH
CE=VIL,A6=VIL
Activate WE Pulse to start
Data don't care
Toggle bit checking
Q6 not Toggled
No
Yes
Increment PLSCNT
Set CE=OE=VIL
A9=VIH
Read from Sector
Addr=SA, A1=1
No
No
Data=01H?
Yes
PLSCNT=32?
Yes
.
Device Failed
Yes
Protect Another
Sector?
No
Write Reset Command
Sector Protection
Complete
REV. 1.1, JUN. 14, 2001
P/N: PM0547
38
MX29F002/002N
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
Protect All Sectors
PLSCNT=1
Write "unlock for sector protect/unprotect"
Command (Table 1)
Set OE=A9=VIH
CE=VIL,A6=1
Activate WE Pulse to start
Data don't care
No
Toggle bit checking
Q6 not Toggled
Increment
PLSCNT
Yes
Set OE=CE=VIL
A9=VIH,A1=1
Set Up First Sector Addr
Read Data from Device
No
No
Data=00H?
Yes
Increment
PLSCNT=1000?
Sector Addr
Yes
Device Failed
No
All sectors have
been verified?
Yes
Write Reset Command
Chip Unprotect
Complete
* It is recommended before unprotect the whole chip, all sectors should be protected in advance.
REV. 1.1, JUN. 14, 2001
P/N: PM0547
39
MX29F002/002N
ID CODE READ TIMING WAVEFORM MODE
VCC
5V
VID
ADD
A9
VIH
VIL
ADD
AD
tACC
tACC
A1 VIH
VIL
ADD
A2-A8
VIH
A10-A17 VIL
CE
VIH
VIL
VIH
VIL
tCE
WE
OE
tOE
VIH
VIL
tDF
tOH
tOH
VIH
VIL
DATA
Q0-Q7
DATA OUT
C2H
DATA OUT
B0h/34h
REV. 1.1, JUN. 14, 2001
P/N: PM0547
40
MX29F002/002N
ORDERING INFORMATION
PLASTIC PACKAGE
PART NO.
Access Time Operating Current Standby Current
Temperature
Range
PACKAGE
(ns)
55
(mA)
30
MAX.(uA)
MX29F002TPC-55
MX29F002TPC-70
MX29F002TPC-90
MX29F002TPC-12
MX29F002TTC-55
5
5
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
70
30
90
30
120
55
30
30
MX29F002TTC-70
MX29F002TTC-90
MX29F002TTC-12
70
90
30
30
30
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
120
MX29F002TQC-55
MX29F002TQC-70
MX29F002TQC-90
MX29F002TQC-12
MX29F002BPC-55
MX29F002BPC-70
MX29F002BPC-90
MX29F002BPC-12
MX29F002BTC-55
55
70
30
30
30
30
30
30
30
30
30
5
5
5
5
5
5
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
90
120
55
70
90
120
55
MX29F002BTC-70
MX29F002BTC-90
MX29F002BTC-12
70
90
30
30
30
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
120
MX29F002BQC-55
MX29F002BQC-70
MX29F002BQC-90
MX29F002BQC-12
MX29F002NTPC-55
MX29F002NTPC-70
MX29F002NTPC-90
MX29F002NTPC-12
MX29F002NTTC-55
55
70
30
30
30
30
30
30
30
30
30
5
5
5
5
5
5
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
90
120
55
70
90
120
55
REV. 1.1, JUN. 14, 2001
P/N: PM0547
41
MX29F002/002N
PART NO.
Access Time Operating Current Standby Current
Temperature
Range
PACKAGE
(ns)
(mA)
MAX.(uA)
MX29F002NTTC-70
MX29F002NTTC-90
MX29F002NTTC-12
70
30
5
0oC~70oC
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
90
30
30
5
5
0oC~70oC
0oC~70oC
120
MX29F002NTQC-55
MX29F002NTQC-70
MX29F002NTQC-90
MX29F002NTQC-12
MX29F002NBPC-55
MX29F002NBPC-70
MX29F002NBPC-90
MX29F002NBPC-12
MX29F002NBTC-55
55
70
30
30
30
30
30
30
30
30
30
5
5
5
5
5
5
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
0oC~70oC
90
120
55
70
90
120
55
MX29F002NBTC-70
MX29F002NBTC-90
MX29F002NBTC-12
70
90
30
30
30
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
120
MX29F002NBQC-55
MX29F002NBQC-70
MX29F002NBQC-90
MX29F002NBQC-12
MX29F002TPI-70
MX29F002TPI-90
MX29F002TPI-12
MX29F002TTI-70
55
70
30
30
30
30
45
45
45
45
5
5
5
5
5
5
5
5
0oC~70oC
0oC~70oC
0oC~70oC
90
120
70
0oC~70oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
90
120
70
MX29F002TTI-90
MX29F002TTI-12
90
45
45
5
5
-40oC~85oC
-40oC~85oC
120
IMX29F002TQI-70
MX29F002TQI-90
MX29F002TQI-12
IMX29F002BPI-70
MX29F002BPI-90
MX29F002BPI-12
70
90
45
45
45
45
45
45
5
5
5
5
5
5
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
120
70
90
120
REV. 1.1, JUN. 14, 2001
P/N: PM0547
42
MX29F002/002N
PART NO.
Access Time Operating Current Standby Current
Temperature
Range
PACKAGE
(ns)
(mA)
MAX.(uA)
IMX29F002BTI-70
MX29F002BTI-90
MX29F002BTI-12
70
45
5
-40oC~85oC
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
90
45
45
5
5
-40oC~85oC
-40oC~85oC
120
MX29F002BQI-70
MX29F002BQI-90
MX29F002BQI-12
MX29F002NTPI-70
MX29F002NTPI-90
MX29F002NTPI-12
MX29F002NTTI-70
70
90
45
45
45
45
45
45
45
5
5
5
5
5
5
5
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
120
70
90
120
70
MX29F002NTTI-90
MX29F002NTTI-12
90
45
45
5
5
-40oC~85oC
-40oC~85oC
120
MX29F002NTQI-70
MX29F002NTQI-90
MX29F002NTQI-12
MX29F002NBPI-70
MX29F002NBPI-90
MX29F002NBPI-12
MX29F002NBTI-70
70
90
45
45
45
45
45
45
45
5
5
5
5
5
5
5
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
-40oC~85oC
120
70
90
120
70
MX29F002NBTI-90
MX29F002NBTI-12
90
45
45
5
5
-40oC~85oC
-40oC~85oC
120
MX29F002NBQI-70
MX29F002NBQI-90
MX29F002NBQI-12
70
90
45
45
45
5
5
5
-40oC~85oC
-40oC~85oC
-40oC~85oC
120
REV. 1.1, JUN. 14, 2001
P/N: PM0547
43
MX29F002/002N
ERASE AND PROGRAMMING PERFORMANCE(1)
LIMITS
PARAMETER
MIN.
TYP.(2)
MAX.(3)
UNITS
Sector Erase Time
1
3
8
s
s
Chip Erase Time
24
Byte Programming Time
Chip Programming Time
Erase/Program Cycles
7
210
10.5
us
3.5
sec
Cycles
100,000
Note: 1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25°C, 5V.
3.Maximum values measured at 25°C, 4.5V.
LATCHUP CHARACTERISTICS
MIN.
-1.0V
MAX.
Input Voltage with respect to GND on all pins except I/O pins
Input Voltage with respect to GND on all I/O pins
Current
13.5V
Vcc + 1.0V
+100mA
-1.0V
-100mA
Includes all pins except Vcc. Test conditions: Vcc = 5.0V, one pin at a time.
DATA RETENTION
PARAMETER
MIN.
UNIT
DataRetentionTime
20
Years
REV. 1.1, JUN. 14, 2001
P/N: PM0547
44
MX29F002/002N
PACKAGE INFORMATION
32-PIN PLASTIC DIP
REV. 1.1, JUN. 14, 2001
P/N: PM0547
45
MX29F002/002N
32-PIN PLASTIC LEADED CHIP CARRIER (PLCC)
REV. 1.1, JUN. 14, 2001
P/N: PM0547
46
MX29F002/002N
32-PIN PLASTIC TSOP
REV. 1.1, JUN. 14, 2001
P/N: PM0547
47
MX29F002/002N
REVISION HISTORY
Revision Description
Page
Date
1.0
1.To remove "Advanced Information" datasheet marking and
P1
DEC/27/1999
contain information on products in full production
2.The modification summary of Revision 0.9.8 to Revision 1.0:
2-1.Program/erase cycle times:10K cycles-->100K cycles
2-2.To add data retention 20 years
P1,46
P1,46
2-3.To add industrial grade range from "Read Mode" to "Full Range"P17,19,21,41-43
2-4.To remove A9 from "timing waveform for sector protection for P36
system without 12V"
To remove A9 from "timing waveform for chip unprotection for P37
system without 12V"
2-5.Multi-sectorerasetime-out:30ms-->30us,tBAL:80us-->100us
To modify "Package Information"
P8,20,21
P45~47
1.1
JUN/14/2001
REV. 1.1, JUN. 14, 2001
P/N: PM0547
48
MX29F002/002N
M
ACRONIX
I
NTERNATIONAL
CO.,
LTD.
HEADQUARTERS:
TEL:+886-3-578-6688
FAX:+886-3-563-2888
EUROPE OFFICE:
TEL:+32-2-456-8020
FAX:+32-2-456-8021
JAPAN OFFICE:
TEL:+81-44-246-9100
FAX:+81-44-246-9105
SINGAPORE OFFICE:
TEL:+65-348-8385
FAX:+65-348-8096
TAIPEI OFFICE:
TEL:+886-2-2509-3300
FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-453-8088
FAX:+1-408-453-8488
CHICAGO OFFICE:
TEL:+1-847-963-1900
FAX:+1-847-963-1909
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
49
相关型号:
©2020 ICPDF网 联系我们和版权申明