MX29F004TTC-55 [Macronix]
4M-BIT [512KX8] CMOS FLASH MEMORY; 4M- BIT [ 512KX8 ] CMOS FLASH MEMORY型号: | MX29F004TTC-55 |
厂家: | MACRONIX INTERNATIONAL |
描述: | 4M-BIT [512KX8] CMOS FLASH MEMORY |
文件: | 总39页 (文件大小:588K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MX29F004T/B
4M-BIT[512KX8]CMOSFLASHMEMORY
FEATURES
• 524,288 x 8 only
• Erase suspend/Erase Resume
- Suspends an erase operation to read data from, or
program data to, another sector that is not being
erased, then resumes the erase.
• Single power supply operation
- 5.0V only operation for read, erase and program op-
eration
• Fast access time: 70/90/120ns
• Low power consumption
• Status Reply
- Data polling & Toggle bit for detection of program
and erase cycle completion.
- 30mA maximum active current (5MHz)
- 1uA typical standby current
• Chip protect/unprotect for 5V only system or 5V/12V
system.
• Command register architecture
- Byte Programming (7us typical)
- Sector Erase
• 100,000 minimum erase/program cycles
• Latch-up protected to 100mA from -1V to VCC+1V
• Low VCC write inhibit is equal to or less than 3.2V
• Package type:
(Sector structure:16KB/8KB/8KB/32KB and 64KBx7)
• Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors with
Erase Suspend capability.
- 32-pin PLCC, TSOP or PDIP
• Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
- Automatically program and verify data at specified
address
• 20 years data retention
GENERAL DESCRIPTION
The MX29F004T/B is a 4-mega bit Flash memory orga-
nized as 512K bytes of 8 bits. MXIC's Flash memories
offer the most cost-effective and reliable read/write non-
volatile random access memory. The MX29F004T/B is
packaged in 32-pin PLCC, TSOP, PDIP. It is designed
to be reprogrammed and erased in system or in stan-
dard EPROM programmers.
during erase and programming, while maintaining maxi-
mum EPROM compatibility.
MXIC Flash technology reliably stores memory
contents even after 100,000 erase and program
cycles. The MXIC cell is designed to optimize the
erase and programming mechanisms. In addition,
the combination of advanced tunnel oxide
processing and low internal electric fields for erase
and program operations produces reliable cycling.
The MX29F004T/B uses a 5.0V±10% VCC supply
to perform the High Reliability Erase and auto
Program/Erase algorithms.
The standard MX29F004T/B offers access time as fast
as 70ns, allowing operation of high-speed microproces-
sors without wait states. To eliminate bus contention,
the MX29F004T/B has separate chip enable (CE) and
output enable (OE) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29F004T/B uses a command register to manage this
functionality. The command register allows for 100%
TTL level control inputs and fixed power supply levels
The highest degree of latch-up protection is
achieved with MXIC's proprietary non-epi process.
Latch-up protection is proved for stresses up to 100
milliamps on address and data pin from -1V to VCC
+ 1V.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
1
MX29F004T/B
PIN CONFIGURATIONS
32 PDIP
32 PLCC
VCC
WE
A17
A14
A13
A8
A18
A16
A15
A12
A7
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
1
2
3
4
1
32
30
29
4
5
9
A7
A6
A5
A4
A3
A2
A1
A0
Q0
A14
A13
A8
5
A6
6
A9
A5
7
A11
OE
A10
CE
A4
8
A9
A3
9
MX29F004T/B
25
A11
OE
A10
CE
Q7
A2
10
11
12
13
14
15
16
A1
Q7
A0
Q6
Q0
Q5
Q1
13
14
21
Q4
Q2
17
20
Q3
GND
32TSOP (StandardType) (8mm x 20mm)
A11
A9
1
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
GND
Q2
Q1
Q0
A0
2
A8
3
A13
A14
A17
WE
VCC
A18
A16
A15
A12
A7
4
5
6
7
8
MX29F004T/B
9
10
11
12
13
14
15
16
A6
A1
A5
A2
A4
A3
PIN DESCRIPTION
SYMBOL
A0~A18
Q0~Q7
CE
PIN NAME
Address Input
Data Input/Output
Chip Enable Input
Write Enable Input
Output Enable Input
Ground Pin
WE
OE
GND
VCC
+5.0V single power supply
P/N:PM0554
REV. 1.9, OCT. 19, 2004
2
MX29F004T/B
SECTOR STRUCTURE
MX29F004TTOP BOOT SECTOR ADDRESSTABLE
Sector Size
Address Range (in hexadecimal)
(x8) Address Range
00000h-0FFFFh
Sector
SA0
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
A18
0
A17
0
A16
0
A15
X
A14
X
A13
X
(Kbytes)
64
64
64
64
64
64
64
32
8
0
0
1
X
X
X
10000h-1FFFFh
0
1
0
X
X
X
20000h-2FFFFh
0
1
1
X
X
X
30000h-3FFFFh
1
0
0
X
X
X
40000h-4FFFFh
1
0
1
X
X
X
50000h-5FFFFh
1
1
0
X
X
X
60000h-6FFFFh
1
1
1
0
X
X
70000h-77FFFh
1
1
1
1
0
0
78000h-79FFFh
1
1
1
1
0
1
8
7A000h-7BFFFh
7C000h-7FFFFh
1
1
1
1
1
X
16
MX29F004B BOTTOM BOOT SECTOR ADDRESSTABLE
Sector Size
Address Range (in hexadecimal)
(x8) Address Range
00000h-03FFFh
Sector
SA0
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
A18
0
A17
0
A16
0
A15
0
A14
0
A13
X
(Kbytes)
16
8
0
0
0
0
1
0
04000h-05FFFh
0
0
0
0
1
1
8
06000h-07FFFh
0
0
0
1
X
X
32
64
64
64
64
64
64
64
08000h-0FFFFh
0
0
1
X
X
X
10000h-1FFFFh
0
1
0
X
X
X
20000h-2FFFFh
0
1
1
X
X
X
30000h-3FFFFh
1
0
0
X
X
X
40000h-4FFFFh
1
0
1
X
X
X
50000h-5FFFFh
1
1
0
X
X
X
60000h-6FFFFh
1
1
1
X
X
X
70000h-7FFFFh
P/N:PM0554
REV. 1.9, OCT. 19, 2004
3
MX29F004T/B
BLOCK DIAGRAM
WRITE
STATE
CONTROL
INPUT
PROGRAM/ERASE
HIGH VOLTAGE
CE
OE
WE
MACHINE
(WSM)
LOGIC
STATE
MX29F004T/B
FLASH
ADDRESS
LATCH
REGISTER
ARRAY
ARRAY
A0-A18
AND
SOURCE
HV
BUFFER
Y-PASS GATE
COMMAND
DATA
DECODER
PGM
SENSE
DATA
HV
AMPLIFIER
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
Q0-Q7
I/O BUFFER
P/N:PM0554
REV. 1.9, OCT. 19, 2004
4
MX29F004T/B
AUTOMATIC PROGRAMMING
AUTOMATIC ERASE ALGORITHM
The MX29F004T/B is byte programmable using the Au-
tomatic Programming algorithm. The Automatic Pro-
gramming algorithm makes the external system do not
need to have time out sequence nor to verify the data
programmed. The typical chip programming time at room
temperature of the MX29F004T/B is less than 4 sec-
onds.
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using stan-
dard microprocessor write timings. The device will auto-
matically pre-program and verification the entire array.
Then the device automatically times the erase pulse
width, provides the erase verify, and counts the number
of sequences. A status bit toggling between consecu-
tive read cycles provides feedback to the user as to the
status of the programming operation.
AUTOMATIC CHIP ERASE
Register contents serve as inputs to an internal state-
machine which controls the erase and programming cir-
cuitry. During write cycles, the command register inter-
nally latches address and data needed for the program-
ming and erase operations. During a system write cycle,
addresses are latched on the falling edge ofWE or CE,
whichever happens later, and data are latched on the
rising edge of WE or CE, whichever happens first.
The entire chip is bulk erased using 10 ms erase pulses
according to MXIC's Automatic Chip Erase algorithm.
Typical erasure at room temperature is accomplished in
less than 4 second. The Automatic Erase algorithm
automatically programs the entire array prior to electri-
cal erase. The timing and verification of electrical erase
are controlled internally within the device.
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, reli-
ability, and cost effectiveness.The MX29F004T/B elec-
trically erases all bits simultaneously using Fowler- tun-
neling. The bytes are programmed by using the EPROM
programming mechanism of hot electron injection.
AUTOMATIC SECTOR ERASE
The MX29F004T/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. Sector erase modes allow
sectors of the array to be erased in one erase cycle.
The Automatic Sector Erase algorithm automatically
programs the specified sector(s) prior to electrical erase.
The timing and verification of electrical erase are con-
trolled internally within the device.
During a program cycle, the state-machine will control
the program sequences and command register will not
respond to any command set. During a Sector Erase
cycle, the command register will only respond to Erase
Suspend command. After Erase Suspend is completed,
the device stays in read mode. After the state machine
has completed its task, it will allow the command regis-
ter to respond to its full command set.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write program set-up commands (including
2 unlock write cycle and A0H) and a program command
(program data and address). The device automatically
times the programming pulse width, provides the pro-
gram verification, and counts the number of sequences.
A status bit similar to DATA polling and a status bit tog-
gling between consecutive read cycles, provide feed-
back to the user as to the status of the programming
operation.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
5
MX29F004T/B
TABLE1. SOFTWARE COMMAND DEFINITIONS
First Bus
Cycle
Second Bus Third Bus
Cycle Cycle
Fourth Bus Fifth Bus
Cycle Cycle
Sixth Bus
Cycle
Command
Bus
Cycle Addr
XXXH F0H
RA RD
555H AAH 2AAH 55H 555H 90H
555H AAH 2AAH 55H 555H 90H
Data Addr Data Addr Data Addr Data Addr Data Addr Data
Reset
1
Read
1
Read Silicon ID
Chip Protect Verify
4
4
ADI DDI
SA 00H
x02 01H
555H AAH 2AAH 55H 555H A0H PA PD
Program
4
6
6
1
1
6
Chip Erase
555H AAH 2AAH 55H 555H 80H
555H AAH 2AAH 55H 555H 80H
XXXH B0H
555H AAH 2AAH 55H
555H AAH 2AAH 55H
555H 10H
SA 30H
Sector Erase
Sector Erase Suspend
Sector Erase Resume
Unlock for chip
protect/unprotect
XXXH 30H
555H AAH 2AAH 55H 555H 80H
555H AAH 2AAH 55H
555H 20H
Note:
1. ADI = Address of Device identifier; A1=0, A0 = 0 for manufacture code,A1=0, A0 =1 for device code A2~A18=Do not care.
(Refer to table 3)
DDI = Data of Device identifier : C2H for manufacture code, 45H/46H for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2. PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address to the sector to be erased.
3. The system should generate the following address patterns: 555H or 2AAH to Address A10~A0.
Address bit A11~A18=X=Don't care for all address commands except for Program Address (PA) and Sector Address (SA).
Write Sequence may be initiated with A11~A18 in either state.
4. For Chip Protect Verify Operation :If read out data is 01H, it means the chip has been protected. If read out data is 00H, it
means the chip is still not being protected.
COMMAND DEFINITIONS
Device operations are selected by writing specific ad-
dress and data sequences into the command register.
Writing incorrect address and data values or writing them
in the improper sequence will reset the device to the
read mode. Table 1 defines the valid register command
sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the
Sector Erase operation is in progress. Either of the two
reset command sequences will reset the device (when
applicable).
P/N:PM0554
REV. 1.9, OCT. 19, 2004
6
MX29F004T/B
TABLE 2. MX29F004T/B BUS OPERATION
Mode
Pins
CE
L
OE
WE
A0
A1
A6
A9
Q0 ~ Q7
Read Silicon ID
ManufacturerCode(1)
Read Silicon ID
DeviceCode(1)
Read
L
H
L
L
X
VID(2)
C2H
L
L
H
H
L
X
VID(2)
45H/46H
L
H
L
L
L
L
H
X
H
L
A0
X
A1
X
A6
X
A9
X
DOUT
Standby
X
HIGH Z
HIGH Z
DIN(3)
X
OutputDisable
Write
H
X
X
X
X
H
A0
X
A1
X
A6
L
A9
VID(2)
Chip Protect with 12V
system (6)
VID(2)
L
Chip Unprotect with 12V
system (6)
L
L
L
L
L
X
VID(2)
L
X
X
X
X
X
X
X
H
X
X
H
X
H
X
L
VID(2)
VID(2)
H
X
Verify Chip Protect
with 12V system
Chip Protect without 12V
system (6)
L
H
L
Code(5)
X
H
H
L
Chip Unprotect without 12V
system (6)
L
H
X
X
H
X
Verify Chip Protect/Unprotect
without 12V system (7)
Reset
H
X
H
Code(5)
HIGH Z
X
X
NOTES:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table
1.
2. VID is the Silicon-ID-Read high voltage, 11.5V to 12.5V.
3. Refer to Table 1 for valid Data-In during a write operation.
4. X can be VIL or VIH.
5. Code=00H means unprotected.
Code=01H means protected.
6. Refer to chip protect/unprotect algorithm and waveform.
Must issue "unlock for chip protect/unprotect" command before "chip protect/unprotect without 12V system"
command.
7. The "verify chip protect/unprotect without 12V system" is only following "Chip protect/unprotect without 12V
system" command.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
7
MX29F004T/B
READ/RESET COMMAND
SET-UP AUTOMATIC CHIP/SECTOR ERASE
The read or reset operation is initiated by writing the read/
reset command sequence into the command register.
Microprocessor read cycles retrieve array data. The de-
vice remains enabled for reads until the command regis-
ter contents are altered.
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cy-
cles are then followed by the chip erase command 10H.
The Automatic Chip Erase does not require the device
to be entirely pre-programmed prior to executing the Au-
tomatic Chip Erase. Upon executing the Automatic Chip
Erase, the device will automatically program and verify
the entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero
pattern, a self-timed chip erase and verify begin. The
erase and verify operations are completed when the data
on Q7 is "1" at which time the device returns to the
Read mode. The system is not required to provide any
control or timing during these operations.
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid com-
mand must then be written to place the device in the
desired state.
SILICON-ID-READ COMMAND
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manu-
facturer and device codes must be accessible while the
device resides in the target system. PROM program-
mers typically access signature codes by raising A9 to
a high voltage. However, multiplexing high voltage onto
address lines is not generally desired system design prac-
tice.
When using the Automatic Chip Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required).
If the Erase operation was unsuccessful, the data on
Q5 is "1" (see Table 4), indicating the erase operation
exceed internal timing limit.
The MX29F004T/B contains a Silicon-ID-Read operation
to supplement traditional PROM programming method-
ology. The operation is initiated by writing the read sili-
con ID command sequence into the command register.
Following the command write, a read cycle with
A1=VIL,A0=VIL retrieves the manufacturer code of C2H.
A read cycle with A1=VIL, A0=VIH returns the device
code of 45H/46H for MX29F004T/B.
The automatic erase begins on the rising edge of the
last WE or CE, whichever happens first pulse in the
command sequence and terminates when the data on
Q7 is "1" and the data on Q6 stops toggling for two con-
secutive read cycles, at which time the device returns
to the Read mode.
TABLE 3. EXPANDED SILICON ID CODE
Pins
A0
A1
Q7
1
Q6 Q5
Q4
0
Q3 Q2
Q1 Q0 Code(Hex)
Manufacturecode
VIL
VIL
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
0
1
0
0
0
1
0
1
0
C2H
Device code for MX29F004T VIH VIL
Device code for MX29F004B VIH VIL
0
0
45H
0
0
46H
Chip Protection Verification
X
X
VIH
VIH
0
0
01H(Protected)
00H(Unprotected)
0
0
P/N:PM0554
REV. 1.9, OCT. 19, 2004
8
MX29F004T/B
SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the de-
vice to be entirely pre-programmed prior to executing
the Automatic Set-up Sector Erase command and Auto-
matic Sector Erase command. Upon executing the Au-
tomatic Sector Erase command, the device will auto-
matically program and verify the sector(s) memory for
an all-zero data pattern. The system is not required to
provide any control or timing during these operations.
(no erase verification command is required). Sector erase
is a six-bus cycle operation. There are two "unlock"
write cycles. These are followed by writing the set-up
command 80H. Two more "unlock" write cycles are then
followed by the sector erase command 30H. The sector
address is latched on the falling edge of WE or CE,
whichever happens later, while the command (data) is
latched on the rising edge of WE or CE, whichever hap-
pens first. Sector addresses selected are loaded into
internal register on the sixth falling edge of WE or CE,
whichever happens later. Each successive sector load
cycle started by the falling edge of WE or CE, which-
ever happens later must begin within 30us from the ris-
ing edge of the preceding WE or CE, whichever hap-
pens first. Otherwise, the loading period ends and inter-
nal auto sector erase cycle starts. (Monitor Q3 to deter-
mine if the sector erase timer window is still open, see
section Q3, Sector Erase Timer.) Any command other
than Sector Erase(30H) or Erase Suspend(B0H) during
the time-out period resets the device to read mode.
When the sector(s) is automatically verified to contain
an all-zero pattern, a self-timed sector erase and verify
begin. The erase and verify operations are complete
when the data on Q7 is "1" and the data on Q6 stops
toggling for two consecutive read cycles, at which time
the device returns to the Read mode. The system is not
required to provide any control or timing during these
operations.
When using the Automatic Sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
TABLE 4. WRITE OPERATION STATUS
Status
Q7
Q6
Q5
Q3
Q2
Note1
Note2
Byte Program in Auto Program Algorithm
Auto Erase Algorithm
Q7 Toggle
0
0
0
N/A No Toggle
0
1
Toggle
No
1
Toggle
Toggle
Erase Suspend Read
N/A
In Progress
(Erase Suspended Sector)
Erase Suspend Read
Toggle
Erase Suspended Mode
Data Data Data Data
Data
N/A
(Non-Erase Suspended Sector)
Erase Suspend Program
Q7 Toggle
Q7 Toggle
0
1
1
1
N/A
Byte Program in Auto Program Algorithm
N/A No Toggle
Exceeded Auto Erase Algorithm
0
Toggle
1
Toggle
N/A
Time Limits Erase Suspend Program
Q7 Toggle
N/A
Note:
1. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
2. Q5 switches to '1' when an Auto Program or Auto Erase operation has exceeded the maximum timing limits.
See "Q5:Exceeded Timing Limits " for more information.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
9
MX29F004T/B
ings. The device will automatically provide an adequate
internally generated program pulse and verify margin.
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. When the Erase Suspend com-
mand is written during a sector erase operation, the de-
vice requires a maximum of 100us to suspend the erase
operations.However, when the Erase Suspend command
is written during the sector erase time-out, the device
immediately terminates the time-out period and suspends
the erase operation. After this command has been ex-
ecuted, the command register will initiate erase suspend
mode. The state machine will return to read mode auto-
matically after suspend is ready. At this time, state ma-
chine only allows the command register to respond to
the Read Memory Array, Erase Resume and program
commands.
If the program operation was unsuccessful, the data on
Q5 is "1"(see Table 4), indicating the program operation
exceed internal timing limit.The automatic programming
operation is completed when the data read on Q6 stops
toggling for two consecutive read cycles and the data on
Q7 and Q6 are equivalent to data written to these two
bits, at which time the device returns to the Read mode
(no program verify command is required).
DATA POLLING-Q7
The MX29F004T/B also features Data Polling as a
method to indicate to the host system that the Auto-
matic Program or Erase algorithms are either in progress
or completed.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended sectors.
While the Automatic Programming algorithm is in opera-
tion, an attempt to read the device will produce the comple-
ment data of the data last written to Q7. Upon comple-
tion of the Automatic Program Algorithm an attempt to
read the device will produce the true data last written to
Q7. The Data Polling feature is valid after the rising edge
of the fourthWE or CE, whichever happens first pulse of
the four write pulse sequences for automatic program.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
While the Automatic Erase algorithm is in operation, Q7
will read "0" until the erase operation is competed. Upon
completion of the erase operation, the data on Q7 will
read "1". The Data Polling feature is valid after the rising
edge of the sixth WE or CE, whichever happens first
pulse of six write pulse sequences for automatic chip/
sector erase.
SET-UP AUTOMATIC PROGRAM COMMANDS
The Data Polling feature is active during Automatic Pro-
gram/Erase algorithm or sector erase time-out. (see sec-
tion Q3 Sector Erase Timer)
To initiate Automatic Program mode, A three-cycle com-
mand sequence is required. There are two "unlock" write
cycles. These are followed by writing the Automatic Pro-
gram command A0H.
Once the Automatic Program command is initiated, the
next WE or CE pulse causes a transition to an active
programming operation. Addresses are latched on the
falling edge, and data are internally latched on the
rising edge of the WE or CE, whichever happens first
pulse. The rising edge of WE or CE, whichever hap-
pens first also begins the programming operation. The
system is not required to provide further controls or tim-
P/N:PM0554
REV. 1.9, OCT. 19, 2004
10
MX29F004T/B
Q6:Toggle BIT I
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE or CE to control the read
cycles.) But Q2 cannot distinguish whether the sector
is actively erasing or is erase-suspended. Q6, by com-
parison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which
sectors are selected for erasure. Thus, both status bits
are required for sectors and mode information. Refer to
Table 4 to compare outputs for Q2 and Q6.
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid
after the rising edge of the final WE or CE, whichever
happens first pulse in the command sequence (prior to
the program or erase operation), and during the sector
time-out.
During an Automatic Program or Erase algorithm opera-
tion, successive read cycles to any address cause Q6
to toggle. The system may use either OE or CE to con-
trol the read cycles.When the operation is complete, Q6
stops toggling.
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on Q7-Q0 on the following read cycle.
After an erase command sequence is written, if the chip
has been protected, Q6 toggles and returns to reading
array data.
The system can use Q6 and Q2 together to determine
whether a sector is actively erasing or is erase sus-
pended.When the device is actively erasing (that is, the
Automatic Erase algorithm is in progress), Q6 toggling.
When the device enters the Erase Suspend mode, Q6
stops toggling. However, the system must also use Q2
to determine which sectors are erasing or erase-sus-
pended. Alternatively, the system can use Q7.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of Q5 is high
(see the section on Q5). If it is, the system should then
determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as Q5 went
high. If the toggle bit is no longer toggling, the device
has successfully completed the program or erase op-
eration. If it is still toggling, the device did not complete
the operation successfully, and the system must write
the reset command to return to reading array data.
If a program address falls within a protected sector, Q6
toggles for approximately 2us after the program com-
mand sequence is written, then returns to reading array
data.
Q6 also toggles during the erase-suspend-program mode,
and stops toggling once the Automatic Program algo-
rithm is complete.
The remaining scenario is that system initially determines
that the toggle bit is toggling and Q5 has not gone high.
The system may continue to monitor the toggle bit and
Q5 through successive read cycles, determining the sta-
tus as described in the previous paragraph. Alterna-
tively, it may choose to perform other system tasks. In
this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation.
Table 4 shows the outputs for Toggle Bit I on Q6.
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whether a particular sector is actively erasing (that is,
the Automatic Erase algorithm is in process), or whether
that sector is erase-suspended. Toggle Bit I is valid af-
ter the rising edge of the final WE or CE, whichever
happens first pulse in the command sequence.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
11
MX29F004T/B
specific command sequences. The device also incorpo-
rates several features to prevent inadvertent write cycles
resulting fromVCC power-up and power-down transition
or system noise.
Q5
ExceededTiming Limits
Q5 will indicate if the program or erase time has ex-
ceeded the specified limits (internal pulse count). Under
these conditions Q5 will produce a "1". This time-out
condition indicates that the program or erase cycle was
not successfully completed. Data Polling andToggle Bit
are the only operating functions of the device under this
condition.
Q3
Sector Erase Timer
After the completion of the initial sector erase command
sequence, the sector erase time-out will begin. Q3 will
remain low until the time-out is complete. Data Polling
andToggle Bit are valid after the initial sector erase com-
mand sequence.
If this time-out condition occurs during sector erase op-
eration, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still func-
tional and may be used for the program or erase opera-
tion. The device must be reset to use other sectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence. This
allows the system to continue to use the other active
sectors in the device.
If Data Polling or the Toggle Bit indicates the device has
been written with a valid erase command, Q3 may be
used to determine if the sector erase timer window is
still open. If Q3 is high ("1") the internally controlled
erase cycle has begun; attempts to write subsequent
commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or
Toggle Bit. If Q3 is low ("0"), the device will accept addi-
tional sector erase commands. To insure the command
has been accepted, the system software should check
the status of Q3 prior to and following each subsequent
sector erase command. If Q3 were high on the second
status check, the command may not have been accepted.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or com-
bination of sectors are bad.
If this time-out condition occurs during the byte program-
ming operation, it specifies that the entire sector con-
taining that byte is bad and this sector may not be re-
used, (other sectors are still functional and can be re-
used).
WRITE PULSE "GLITCH" PROTECTION
The time-out condition may also appear if a user tries to
program a non blank location without erasing. In this
case the device locks out and never completes the Au-
tomatic Algorithm operation. Hence, the system never
reads a valid data on Q7 bit and Q6 never stops tog-
gling. Once the Device has exceeded timing limits, the
Q5 bit will indicate a "1". Please note that this is not a
device failure condition since the device was incorrectly
used.
Noise pulses of less than 5ns(typical) on CE or WE will
not initiate a write cycle.
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE =VIL, CE =
VIH or WE = VIH. To initiate a write cycle CE and WE
must be a logical zero while OE is a logical one.
DATA PROTECTION
POWER SUPPLY DECOUPLING
The MX29F004T/B is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power transi-
tion. During power up the device automatically resets
the state machine in the Read mode. In addition, with
its control register architecture, alteration of the memory
contents only occurs after successful completion of
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected be-
tween itsVCC and GND.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
12
MX29F004T/B
CHIP PROTECTION WITH 12V SYSTEM
POWER-UP SEQUENCE
The MX29F004T/B features chip protection, which will
disable both program and erase operations. To activate
this mode, the programming equipment must force VID
on address pin A9 and control pin OE, (suggestVID=12V)
A6=VIL and CE=VIL.(see Table 2) Programming of the
protection circuitry begins on the falling edge of the WE
or CE, whichever happens later pulse and is terminated
on the rising edge. Please refer to chip protect algo-
rithm and waveform.
The MX29F004T/B powers up in the Read only mode. In
addition, the memory contents may only be altered after
successful completion of the predefined command se-
quences.
CHIP PROTECTION WITHOUT 12V SYSTEM
The MX29F004T/B also feature a chip protection method
in a system without 12V power supply.The programming
equipment do not need to supply 12 volts to protect all
sectors.The details are shown in chip protect algorithm
and waveform.
To verify programming of the protection circuitry, the pro-
gramming equipment must forceVID on address pin A9
( with CE and OE atVIL and WE atVIH). When A1=1, it
will produce a logical "1" code at device output Q0 for
the protected status. Otherwise the device will produce
00H for the unprotected status. In this mode, the ad-
dresses, except for A1, are don't care. Address loca-
tions with A1 = VIL are reserved to read manufacturer
and device codes. (Read Silicon ID)
CHIP UNPROTECT WITHOUT 12V SYSTEM
The MX29F004T/B also feature a chip unprotection
method in a system without 12V power supply.The pro-
gramming equipment do not need to supply 12 volts to
unprotect all sectors. The details are shown in chip
unprotect algorithm and waveform.
It is also possible to determine if chip is protected in the
system by writing a Read Silicon ID command. Per-
forming a read operation with A1=VIH, it will produce a
logical "1" at Q0 for the protected status.
CHIP UNPROTECT WITH 12V SYSTEM
The MX29F004T/B also features the chip unprotect mode,
so that all sectors are unprotected after chip unprotect
is completed to incorporate any changes in the code.
To activate this mode, the programming equipment must
forceVID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.
(see Table 2) Refer to chip unprotect algorithm and
waveform for the chip unprotect algorithm. The
unprotection mechanism begins on the falling edge of
the WE or CE, whichever happens later pulse and is
terminated on the rising edge.
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs(Q0-Q7) for an unprotected sector. It
is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
13
MX29F004T/B
CAPACITANCE (TA = 25oC, f = 1.0 MHz)
SYMBOL
CIN1
PARAMETER
MIN.
TYP
MAX.
8
UNIT
pF
CONDITIONS
VIN = 0V
Input Capacitance
Control Pin Capacitance
Output Capacitance
CIN2
12
pF
VIN = 0V
COUT
12
pF
VOUT = 0V
READ OPERATION
DC CHARACTERISTICS (TA = 0° CTO 70° C,VCC = 5V±10%)
SYMBOL PARAMETER
MIN.
TYP
MAX.
1
UNIT
uA
uA
mA
uA
mA
mA
V
CONDITIONS
ILI
Input Leakage Current
VIN = GND to VCC
VOUT = GND to VCC
CE = VIH
ILO
Output Leakage Current
Standby VCC current
10
1
ISB1
ISB2
ICC1
ICC2
VIL
1
5
CE = VCC + 0.3V
IOUT = 0mA, f=5MHz
IOUT = 0mA, f=10MHz
Operating VCC current
30
50
0.8
Input Low Voltage
-0.3(NOTE 1)
2.0
VIH
Input High Voltage
VCC + 0.3
0.45
V
VOL
VOH1
VOH2
Output Low Voltage
Output High Voltage(TTL)
V
IOL = 2.1mA
2.4
V
IOH = -2mA
Output High Voltage(CMOS) Vcc-0.4
V
IOH = -100uA,VCC=VCC min
NOTES:
2. VIH max. = VCC + 1.5V for pulse width is equal to or less
than 20 ns.
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
If VIH is over the specified maximum value, read operation
cannot be guaranteed.
AC CHARACTERISTICS (TA = 0oC to 70oC,VCC = 5V±10%)
29F004T/B-55 29F004T/B-70 29F004T/B-90 29F004T/B-12
Symbol PARAMETER
MIN. MAX. MIN.
MAX. MIN.
MAX. MIN. MAX.
UNIT CONDITIONS
tACC
tCE
tOE
tDF
Address to Output Delay
55
55
40
70
70
40
90
90
40
40
120
120
50
ns
ns
ns
ns
CE=OE=VIL
OE=VIL
CE to Output Delay
OE to Output Delay
OE High to Output Float
(Note 1)
CE=VIL
0
0
30
0
0
30
0
0
0
40
CE=VIL
tOH
Address to Output hold
0
ns
CE=OE=VIL
TEST CONDITIONS:
NOTE:
•
•
•
•
Input pulse levels: 0.45V/2.4V
1. tDF is defined as the time at which the output achieves the
open circuit condition and data is no longer driven.
Input rise and fall times is equal to or less than 10ns
Output load: 1 TTL gate + 100pF (Including scope and jig)
Reference levels for measuring timing: 0.8V, 2.0V
P/N:PM0554
REV. 1.9, OCT. 19, 2004
14
MX29F004T/B
NOTICE:
ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed under ABSOLUTE
MAXIMUM RATINGS may cause permanent damage to
the device. This is a stress rating only and functional
operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for
extended period may affect reliability.
RATING
VALUE
Ambient Operating Temperature 0oC to 70oC
Storage Temperature
Applied Input Voltage
Applied Output Voltage
VCC to Ground Potential
A9 & OE
-65oC to 125oC
-0.5V to 7.0V
-0.5V to 7.0V
-0.5V to 7.0V
-0.5V to 13.5V
NOTICE:
Specifications contained within the following tables are
subject to change.
READ TIMING WAVEFORMS
VIH
ADD Valid
Addresses
VIL
tCE
VIH
CE
VIL
VIH
WE
tDF
VIL
tOE
VIH
OE
tACC
VIL
tOH
HIGH Z
HIGH Z
VOH
VOL
Outputs
DATA Valid
COMMAND PROGRAMMING/DATA PROGRAMMING/ERASE OPERATION
DC CHARACTERISTICS (TA = 0oC to 70oC,VCC = 5V±10%)
SYMBOL
PARAMETER
MIN.
TYP
MAX.
30
UNIT
mA
mA
mA
mA
mA
CONDITIONS
ICC1 (Read)
ICC2
Operating VCC Current
IOUT=0mA, f=5MHz
IOUT=0mA, f=10MHz
In Programming
50
ICC3 (Program)
ICC4 (Erase)
ICCES
50
50
In Erase
VCC Erase Suspend Current
2
CE=VIH, Erase Suspended
NOTES:
1. VILmin.=-0.6Vforpulsewidthisequaltoorlessthan20ns.
2. If VIH is over the specified maximum value, programming
operation cannot be guaranteed.
3. ICCES is specified with the device de-selected. If the
device is read during erase suspend mode, current draw
is the sum of ICCES and ICC1 or ICC2.
4. All current are in RMS unless otherwise noted.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
15
MX29F004T/B
AC CHARACTERISTICS TA = 0oC to 70oC, VCC = 5V ± 10%
29F004T/B-55 29F004T/B-70 29F004T/B-90
29F004T/B-12
SYMBOL PARAMETER
MIN.
50
55
45
20
20
0
MAX. MIN.
MAX. MIN.
MAX. MIN.
MAX. UNIT
tOES
tCWC
tCEP
tCEPH1
tCEPH2
tAS
OE setup time
50
50
50
120
50
20
20
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Command programming cycle
WE programming pulse width
WE programming pulse width High
WE programming pulse width High
Address setup time
70
90
45
45
20
20
20
20
0
0
tAH
Address hold time
45
30
0
45
45
50
50
0
tDS
Data setup time
30
45
tDH
Data hold time
0
0
tCESC
tDF
CE setup time before command write
Output disable time (Note 1)
Total erase time in auto chip erase
Total erase time in auto sector erase
Total programming time in auto verify
Sector address load time
CE Hold Time
0
0
0
0
30
30
40
40
ns
s
tAETC
tAETB
tAVT
4(TYP.) 32
4(TYP.) 32
4(TYP.) 32
4(TYP.) 32
1.3(TYP.) 10.4
1.3(TYP.) 10.4
1.3(TYP.) 10.4
1.3(TYP.) 10.4
s
7
210
7
210
7
210
7
210
us
us
ns
ns
us
us
us
ms
tBAL
100
0
100
0
100
0
100
0
tCH
tCS
CE setup to WE going low
Voltage Transition Time
0
0
0
0
tVLHT
tOESP
tWPP1
tWPP2
4
4
4
4
OE Setup Time to WE Active
Write pulse width for chip protect
Write pulse width for chip unprotect
4
4
4
4
10
12
10
12
10
12
10
12
NOTES:
1. tDF defined as the time at which the output achieves the open circuit condition and data is no longer driven.
P/N:PM0554
REV. 1.9, OCT. 19, 2004
16
MX29F004T/B
SWITCHING TEST CIRCUITS
DEVICE UNDER
TEST
1.6K ohm
+5V
CL
1.2K ohm
DIODES=IN3064
OR EQUIVALENT
CL=100pF Including jig capacitance
SWITCHING TEST WAVEFORMS
2.4V
2.0V
0.8V
2.0V
TEST POINTS
0.8V
0.45V
INPUT
OUTPUT
AC TESTING: Inputs are driven at 2.4V for a logic "1" and 0.45V for a logic "0".
Input pulse rise and fall times are <20ns.
COMMAND WRITE TIMING WAVEFORM
VCC
5V
VIH
Addresses
ADD Valid
VIL
tAH
tAS
VIH
VIL
WE
tOES
tCEPH1
tCEP
tCWC
VIH
VIL
CE
OE
tCS
tCH
tDH
VIH
VIL
tDS
VIH
VIL
Data
DIN
P/N:PM0554
REV. 1.9, OCT. 19, 2004
17
MX29F004T/B
AUTOMATIC PROGRAMMING TIMING WAVEFORM
One byte data is programmed. Verify in fast algorithm
and additional programming by external control are not
required because these operations are executed auto-
matically by internal control circuit. Programming
completion can be verified by DATA polling and toggle
bit checking after automatic verification starts. Device
outputs DATA during programming and DATA after pro-
gramming on Q7.(Q6 is for toggle bit; see toggle bit,
DATA polling, timing waveform)
AUTOMATIC PROGRAMMING TIMING WAVEFORM
Vcc 5V
A11~A18
ADD Valid
2AAH
555H
ADD Valid
tAVT
A0~A10
WE
555H
tAS
tCWC
tCEPH1
tAH
tCESC
CE
OE
tCEP
tDS tDH
tDF
Q0,Q1,Q2
Q4(Note 1)
Data In
Data In
DATA
DATA
Command In
Command In
Command In
DATA polling
Command In
DATA
Command In
Command In
Q7
Command #A0H
Command #55H
Command #AAH
(Q0~Q7)
tOE
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
18
MX29F004T/B
AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Write Program Data/Address
NO
Toggle Bit Checking
Q6 not Toggled
YES
.
NO
Invalid
Verify Byte Ok
Command
YES
NO
Q5 = 1
Auto Program Completed
YES
Reset
Auto Program Exceed
Timing Limit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
19
MX29F004T/B
AUTOMATIC CHIP ERASE TIMING WAVEFORM
All data in chip are erased. External erase verification is
not required because data is erased automatically by
internal control circuit. Erasure completion can be
verified by DATA polling and toggle bit checking after
automaticerasestarts. Deviceoutputs0duringerasure
and1aftererasureonQ7.(Q6isfortogglebit;seetoggle
bit, DATA polling, timing waveform)
AUTOMATIC CHIP ERASE TIMING WAVEFORM
Vcc 5V
A11~A18
2AAH
555H
555H
2AAH
A0~A10
WE
555H
tAS
555H
tCWC
tAH
tCEPH1
tAETC
CE
OE
tCEP
tDS tDH
Command In
Q0,Q1,
Command In
Command In
Command In
Command In
Command In
Q4(Note 1)
DATA polling
Command In
Command In
Command In
Command In
Command In
Command In
Q7
Command #80H
Command #AAH
Command #55H
Command #10H
Command #AAH
(Q0~Q7)
Command #55H
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
20
MX29F004T/B
AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
NO
Toggle Bit Checking
Q6 not Toggled
YES
NO
Invalid
DATA Polling
Q7 = 1
Command
YES
.
NO
Q5 = 1
Auto Chip Erase Completed
YES
Reset
Auto Chip Erase Exceed
Timing Limit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
21
MX29F004T/B
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Sector dataindicatedbyA13toA18areerased. External
erase verify is not required because data are erased
automaticallybyinternalcontrolcircuit. Erasurecomple-
tion can be verified by DATA polling and toggle bit
checking after automatic erase starts. Device outputs 0
duringerasureand1aftererasureonQ7.(Q6isfortoggle
bit; see toggle bit, DATA polling, timing waveform)
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Vcc 5V
Sector
Addressn
Sector
Address0
Sector
Address1
A13~A18
555H
555H
555H
tAS
2AAH
2AAH
A0~A10
tCWC
tAH
WE
CE
tCEPH1
tBAL
tAETB
tCEP
tDS
OE
tDH
Command
In
Command
In
Q0,Q1,
Command
In
Command
Command
In
Command
In
Command
Command
In
In
In
Q4(Note 1)
DATA polling
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Q7
Command #AAH Command #55H Command #80H Command #AAH Command #55H Command #30H
(Q0~Q7)
Command #30H
Command #30H
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
22
MX29F004T/B
AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Sector Address
NO
Toggle Bit Checking
Invalid Command
Q6 Toggled ?
YES
Load Other Sector Addrss If Necessary
(Load Other Sector Address)
NO
Last Sector
to Erase
YES
NO
NO
Time-out Bit
Checking Q3=1 ?
YES
Toggle Bit Checking
Q6 not Toggled
YES
NO
Q5 = 1
DATA Polling
Q7 = 1
YES
Reset
Auto Sector Erase Completed
Auto Sector Erase Exceed
Timing Limit
P/N:PM0554
REV. 1.9, OCT. 19, 2004
23
MX29F004T/B
ERASE SUSPEND/ERASE RESUME FLOWCHART
START
Write Data B0H
NO
Toggle Bit checking Q6
not toggled
YES
Read Array or
Program
Reading or
NO
Programming End
YES
Write Data 30H
Continue Erase
Another
NO
Erase Suspend ?
YES
P/N:PM0554
REV. 1.9, OCT. 19, 2004
24
MX29F004T/B
TIMING WAVEFORM FOR CHIP PROTECTION FOR SYSTEM WITH 12V
A1
A6
12V
5V
A9
tVLHT
tVLHT
Verify
12V
5V
OE
tVLHT
tWPP 1
WE
CE
tOESP
Data
01H
F0H
tOE
P/N:PM0554
REV. 1.9, OCT. 19, 2004
25
MX29F004T/B
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITH 12V
A1
12V
5V
A9
A6
tVLHT
Verify
12V
5V
OE
tVLHT
tVLHT
tWPP 2
WE
CE
tOESP
Data
00H
F0H
tOE
P/N:PM0554
REV. 1.9, OCT. 19, 2004
26
MX29F004T/B
CHIP PROTECTION ALGORITHM FOR SYSTEM WITH 12V
START
PLSCNT=1
OE=VID,A9=VID,CE=VIL
A6=VIL
Activate WE Pulse
Time Out 10us
Set WE=VIH, CE=OE=VIL
A9 should remain VID
Read Data with A1=1
No
No
Data=01H?
Yes
PLSCNT=32?
Yes
Remove VID from A9
Write Reset Command
Device Failed
Chip Protection
Complete
P/N:PM0554
REV. 1.9, OCT. 19, 2004
27
MX29F004T/B
TIMING WAVEFORM FOR CHIP PROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Don't care
(Note 2)
Data
01H
F0H
tOE
Note: 1. Must issue "unlock for sector protect/unprotect" command
before chip protection for a system without 12V provided.
2. Except F0H
P/N:PM0554
REV. 1.9, OCT. 19, 2004
28
MX29F004T/B
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Don't care
(Note 2)
Data
F0H
00H
tOE
Note: 1. Must issue "unlock for sector protect/unprotect" command
before chip unprotection for a system without 12V provided.
2. Except F0H
P/N:PM0554
REV. 1.9, OCT. 19, 2004
29
MX29F004T/B
CHIP PROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
PLSCNT=1
Write "unlock for chip protect/unprotect"
Command(Table1)
OE=VIH, A9=VIH
CE=VIL, A6=VIL
Activate WE Pulse to start
Data don't care
.
No
Toggle bit checking
Q6 not Toggled
Yes
Increment PLSCNT
Set CE=OE=VIL
A9=VIH
Read Data from chip,
A1=1
No
No
Data=01H?
PLSCNT=32?
Yes
Write Reset Command
Device Failed
Chip Protection
Complete
P/N:PM0554
REV. 1.9, OCT. 19, 2004
30
MX29F004T/B
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
PLSCNT=1
Write "unlock for chip protect/unprotect"
Command (Table 1)
Set OE=A9=VIH
CE=VIL, A6=1
Active WE Pulse to start
Data don't care
Increment
PLSCNT
No
Toggle bit checking
Q6 not Toggled
Yes
Set OE=CE=VIL,
A9=VIH, A1=1
No
Read Data from Device
No
Data=00H?
PLSCNT=1000?
Yes
Yes
Device Failed
Write Reset Command
Chip Unprotect
Complete
P/N:PM0554
REV. 1.9, OCT. 19, 2004
31
MX29F004T/B
ID CODE READ TIMING WAVEFORM
VCC
5V
VID
ADD
A9
VIH
VIL
VIH
VIL
ADD
A0
tACC
tACC
VIH
VIL
A1
ADD
A2-A8
VIH
A10-A18 VIL
CE
VIH
VIL
VIH
VIL
tCE
WE
OE
tOE
VIH
VIL
tDF
tOH
tOH
VIH
VIL
DATA
Q0-Q7
DATA OUT
C2H
DATA OUT
45H/46H
P/N:PM0554
REV. 1.9, OCT. 19, 2004
32
MX29F004T/B
ORDERING INFORMATION
PLASTIC PACKAGE
(Top Boot Sector as an example, For Bottom Boot Sector ones, MX29F004TXX will be changed to MX29F004Bxx)
Part No.
Access
OperatingCurrent StandbyCurrent Package
Remark
Time (ns)
MAX.(mA)
MAX.(uA)
MX29F004TQC-55
MX29F004TQC-70
MX29F004TQC-90
MX29F004TQC-12
MX29F004TTC-55
55
70
30
30
30
30
30
5
5
5
5
5
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PDIP
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
32 Pin TSOP
(Normal Type)
90
120
55
MX29F004TTC-70
MX29F004TTC-90
MX29F004TTC-12
70
90
30
30
30
5
5
5
120
MX29F004TPC-55
MX29F004TPC-70
MX29F004TPC-90
MX29F004TPC-12
MX29F004TQC-55G
MX29F004TQC-70G
MX29F004TQC-90G
MX29F004TQC-12G
MX29F004TTC-55G
55
70
30
30
30
30
30
30
30
30
30
5
5
5
5
5
5
5
5
5
90
120
55
Pb-free
Pb-free
Pb-free
Pb-free
Pb-free
70
90
120
55
MX29F004TTC-70G
MX29F004TTC-90G
MX29F004TTC-12G
70
90
30
30
30
5
5
5
Pb-free
Pb-free
Pb-free
120
P/N:PM0554
REV. 1.9, OCT. 19, 2004
33
MX29F004T/B
ERASE AND PROGRAMMING PERFORMANCE (1)
LIMITS
PARAMETER
MIN.
TYP.(2)
MAX.(3)
UNITS
Sector Erase Time
1.3
4
10.4
32
sec
sec
Chip Erase Time
Byte Programming Time
Chip Programming Time
Erase/Program Cycles
7
210
12
us
4
sec
100,000
Cycles
Note: 1. Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25° C,5V.
3.Maximum values measured at 25° C,4.5V.
LATCH-UP CHARACTERISTICS
MIN.
-1.0V
MAX.
Input Voltage with respect to GND on all pins except I/O pins
Input Voltage with respect to GND on all I/O pins
Current
13.5V
Vcc + 1.0V
+100mA
-1.0V
-100mA
Includes all pins except Vcc. Test conditions: Vcc = 5.0V, one pin at a time.
DATA RETENTION
PARAMETER
MIN.
UNIT
Data Retention Time
20
Years
P/N:PM0554
REV. 1.9, OCT. 19, 2004
34
MX29F004T/B
PACKAGE INFORMATION
P/N:PM0554
REV. 1.9, OCT. 19, 2004
35
MX29F004T/B
P/N:PM0554
REV. 1.9, OCT. 19, 2004
36
MX29F004T/B
P/N:PM0554
REV. 1.9, OCT. 19, 2004
37
MX29F004T/B
REVISION HISTORY
Revision
Description
Page
Date
1.0
To remove "Advanced Information" data sheet marking and
contain information on products in full production.
To improve ICC1 spec:from 40mA @5MHz to 30mA @5MHz
1. Program/erase cycle times:10K cycles-->100K cycles
2.To add data retention minimum 20 years
P1
JUL/01/1999
1.1
1.2
P1,14,15,33
P1,34
P1,34
JUL/12/1999
DEC/20/1999
3.To modify timing of sector address loading period while
operating multi-sector erase from 80us to 30us
4. To modify tBAL from 80us to 100us
P9
P16
5. To remove A9 from "timing waveform for sector protection for P28
system without 12V"
To remove A9 from "timing waveform for chip unprotection for P29
system without 12V"
1.3
Add erase suspend ready max. 100us in ERASE SUSPEND's P10
section at page 10
MAY/30/2000
1.4
1.5
1.6
To modify "Package Information"
1.To corrected typing error
1. Add 55ns speed option
2. Add industrial grade level
1. Removed industrial grade
P35~37
All
JUN/12/2001
JUL/01/2002
JUL/18/2002
P14,16,33
P14,15,16,33
P14~16,33
P35~37
P33
1.7
1.8
1.9
AUG/12/2002
NOV/21/2002
OCT/18/2004
To modify Package Information
1.Added Pb-free part no.in Ordering Information
P/N:PM0554
REV. 1.9, OCT. 19, 2004
38
MX29F004T/B
MACRONIX INTERNATIONALCO., LTD.
Headquarters:
TEL:+886-3-578-6688
FAX:+886-3-563-2888
Europe Office :
TEL:+32-2-456-8020
FAX:+32-2-456-8021
Hong Kong Office :
TEL:+86-755-834-335-79
FAX:+86-755-834-380-78
Japan Office :
Kawasaki Office :
TEL:+81-44-246-9100
FAX:+81-44-246-9105
Osaka Office :
TEL:+81-6-4807-5460
FAX:+81-6-4807-5461
Singapore Office :
TEL:+65-6346-5505
FAX:+65-6348-8096
Taipei Office :
TEL:+886-2-2509-3300
FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-262-8887
FAX:+1-408-262-8810
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
相关型号:
©2020 ICPDF网 联系我们和版权申明