MX29LV002CBQI-90 [Macronix]
2M-BIT [256K x 8] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY; 2M- BIT [ 256K ×8 ] CMOS单电压3V仅限于Flash存储器型号: | MX29LV002CBQI-90 |
厂家: | MACRONIX INTERNATIONAL |
描述: | 2M-BIT [256K x 8] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
文件: | 总58页 (文件大小:513K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MX29LV002C/002NC T/B
2M-BIT [256K x 8] CMOS SINGLE VOLTAGE
3V ONLY FLASH MEMORY
FEATURES
• Extended single - supply voltage range 2.7V to 3.6V
• 262,411 x 8
• Singlepowersupplyoperation
- 3.0V only operation for read, erase and program
operation
• Ready/Busy# pin (RY/BY#)
-Providesahardwaremethodofdetectingprogramor
eraseoperationcompletion.
• Sectorprotection
- Hardware method to disable any combination of
sectors from program or erase operations
-Temporarysectorunprotectallowscodechangesin
previously locked sectors
• Fast access time: 70/90ns
• Lowpowerconsumption
- 20mA maximum active current
- 0.2uA typical standby current
• CFI (Common Flash Interface) compliant
- Flash device parameters stored on the device and
provide the host system to access
• 100,000minimumerase/programcycles
• Latch-up protected to 100mA from -1V to VCC+1V
• Boot Sector Architecture
• Commandregisterarchitecture
- Byte Programming (9us typical)
- Sector Erase (Sector structure 16K-Byte x 1,
8K-Byte x 2, 32K-Byte x1, and 64K-Byte x3)
• Auto Erase (chip & sector) and Auto Program
-Automaticallyeraseanycombinationofsectorswith
Erase Suspend capability.
- T = Top Boot Sector
- B = Bottom Boot Sector
- Automatically program and verify data at specified
address
• Erasesuspend/EraseResume
- Suspends sector erase operation to read data from,
orprogramdatato,any sectorthatisnotbeingerased,
then resumes the erase.
• HardwareRESET#pin(onlyfor29LV002C)
- Resets internal state machine to read mode
• Package type:
- 32-pin TSOP (type 1)
-32-pinPLCC
• 20 years data retention
• Status Reply
- Data# Polling & Toggle bit for detection of program
anderaseoperationcompletion.
GENERAL DESCRIPTION
The MX29LV002C T/B is a 2-mega bit Flash memory
organized as 256K bytes of 8 bits. MXIC's Flash memo-
ries offer the most cost-effective and reliable read/write
non-volatile random access memory. The MX29LV002C
T/B is packaged in 32-pin TSOP and 32-pin PLCC. It is
designed to be reprogrammed and erased in system or
in standard EPROM programmers.
TTL level control inputs and fixed power supply levels
during erase and programming, while maintaining maxi-
mum EPROM compatibility.
MXIC Flash technology reliably stores memory contents
even after 100,000 erase and program cycles. The MXIC
cell is designed to optimize the erase and programming
mechanisms. In addition, the combination of advanced
tunnel oxide processing and low internal electric fields
for erase and program operations produces reliable cy-
cling. The MX29LV002C T/B uses a 2.7V~3.6V VCC
supply to perform the High Reliability Erase and auto
Program/Erase algorithms.
The standard MX29LV002C T/B offers access time as
fast as 70ns, allowing operation of high-speed micropro-
cessors without wait states. To eliminate bus conten-
tion, the MX29LV002C T/B has separate chip enable
(CE#) and output enable (OE#) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29LV002CT/B uses a command register to manage
this functionality. The command register allows for 100%
The highest degree of latch-up protection is achieved
with MXIC's proprietary non-epi process. Latch-up pro-
tection is proved for stresses up to 100 milliamps on
address and data pin from -1V to VCC + 1V.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
1
MX29LV002C/002NC T/B
PIN CONFIGURATIONS
32 TSOP (TYPE 1)
NC on MX29LV002NC
32 PLCC
A11
A9
1
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE#
A10
CE#
Q7
2
A8
3
4
1
32
30
29
A13
A14
A17
WE#
VCC
RESET#
A16
A15
A12
A7
4
5
9
A7
A6
A5
A4
A3
A2
A1
A0
Q0
A14
A13
A8
5
Q6
6
Q5
7
Q4
MX29LV002C/002NC T/B
8
Q3
A9
MX29LV002C/
002NC T/B
9
GND
Q2
25
A11
OE#
A10
CE#
Q7
10
11
12
13
14
15
16
Q1
Q0
A0
A6
A1
13
14
21
A5
A2
17
20
A4
A3
NC on MX29LV002NC
PIN DESCRIPTION
SYMBOL PIN NAME
A0~A17
Q0~Q7
CE#
Address Input
DataInput/Output
Chip Enable Input
Write Enable Input
WE#
RESET#
HardwareResetPin/SectorProtect
Unlock
OE#
VCC
GND
Output Enable Input
Power Supply Pin (+3V)
GroundPin
SECTOR STRUCTURE
A 1 7 ~ A 0
3 F F F F H
A 1 7 ~ A 0
3 F F F F H
1 6 K - B Y T E
( B O O T S E C T O R )
6 4 K - B Y T E
6 4 K - B Y T E
2 F F F F H
1 F F F F H
0 F F F F H
0 7 F F F H
0 5 F F F H
0 3 F F F H
0 0 0 0 0 H
3 B F F F H
3 9 F F F H
8
8
K - B Y T E
K - B Y T E
6 4 K - B Y T E
3 2 K - B Y T E
3 7 F F F H
2 F F F F H
1 F F F F H
3 2 K - B Y T E
6 4 K - B Y T E
6 4 K - B Y T E
6 4 K - B Y T E
8
8
K - B Y T E
K - B Y T E
1 6 K - B Y T E
( B O O T S E C T O R )
0 F F F F H
0 0 0 0 0 H
MX29LV002CT Sector Architecture
MX29LV002CB Sector Architecture
P/N:PM1204
REV. 1.0, JUN. 30, 2005
2
MX29LV002C/002NC T/B
BLOCK DIAGRAM
WRITE
WE#
OE#
CONTROL
PROGRAM/ERASE
HIGH VOLTAGE
STATE
MACHINE
(WSM)
INPUT
LOGIC
WP#
RESET#
STATE
REGISTER
FLASH
ARRAY
ADDRESS
LATCH
ARRAY
A0~A17
AND
SOURCE
HV
BUFFER
Y-PASS GATE
COMMAND
DATA
DECODER
PGM
DATA
HV
SENSE
AMPLIFIER
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
I/O BUFFER
Q0-Q7
P/N:PM1204
REV. 1.0, JUN. 30, 2005
3
MX29LV002C/002NC T/B
AUTOMATIC ERASE ALGORITHM
AUTOMATIC PROGRAMMING
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using stan-
dard microprocessor write timings. The device will auto-
matically pre-program and verify the entire array. Then
the device automatically times the erase pulse width,
provides the erase verification, and counts the number
of sequences. A status bit toggling between consecu-
tive read cycles provides feedback to the user as to the
status of the erasing operation.
The MX29LV002C T/B is byte programmable using the
Automatic Programming algorithm. The Automatic Pro-
gramming algorithm makes the external system do not
need to have time out sequence nor to verify the data
programmed. The typical chip programming time at room
temperature of the MX29LV002C T/B is less than 10
seconds.
AUTOMATIC CHIP ERASE
Register contents serve as inputs to an internal state-
machine which controls the erase and programming cir-
cuitry. During write cycles, the command register inter-
nally latches address and data needed for the program-
ming and erase operations. During a system write cycle,
addresses are latched on the falling edge, and data are
latched on the rising edge of WE# or CE#, whichever
happens first.
The entire chip is bulk erased using 10 ms erase pulses
according to MXIC's Automatic Chip Erase algorithm.
Typical erasure at room temperature is accomplished in
less than 4 second. The Automatic Erase algorithm au-
tomatically programs the entire array prior to electrical
erase. The timing and verification of electrical erase are
controlled internally within the device.
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, reli-
ability, and cost effectiveness. The MX29LV002C T/B
electrically erases all bits simultaneously using Fowler-
Nordheim tunneling. The bytes are programmed by us-
ing the EPROM programming mechanism of hot elec-
tron injection.
AUTOMATIC SECTOR ERASE
The MX29LV002CT/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. The Automatic Sector
Erase algorithm automatically programs the specified
sector(s) prior to electrical erase. The timing and verifi-
cation of electrical erase are controlled internally within
the device. An erase operation can erase one sector,
multiple sectors, or the entire device.
During a program cycle, the state-machine will control
the program sequences and command register will not
respond to any command set. During a Sector Erase
cycle, the command register will only respond to Erase
Suspend command. After Erase Suspend is completed,
the device stays in read mode. After the state machine
has completed its task, it will allow the command regis-
ter to respond to its full command set.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write program set-up commands (including
2 unlock write cycle and A0H) and a program command
(program data and address). The device automatically
times the programming pulse width, provides the pro-
gram verification, and counts the number of sequences.
The device provides an unlock bypass mode with faster
programming. Only two write cycles are needed to pro-
gram a byte, instead of four. A status bit similar to Data#
Polling and a status bit toggling between consecutive
read cycles, provide feedback to the user as to the sta-
tus of the programming operation. Refer to write opera-
tion status, table7, for more information on these status
bits.
AUTOMATIC SELECT
The automatic select mode provides manufacturer and
device identification, and sector protection verification,
through identifier codes output on Q7~Q0.This mode is
mainly adapted for programming equipment on the de-
vice to be programmed with its programming algorithm.
When programming by high voltage method, automatic
select mode requires VID (11.5V to 12.5V) on address
pin A9 and other address pin A6, A1 as referring toTable
3. In addition, to access the automatic select codes in-
system, the host can issue the automatic select com-
P/N:PM1204
REV. 1.0, JUN. 30, 2005
4
MX29LV002C/002NC T/B
mand through the command register without requiringVID,
as shown in table4.
To verify whether or not sector being protected, the sec-
tor address must appear on the appropriate highest or-
der address bit (see Table 1 and Table 2). The rest of
address bits, as shown in table3, are don't care. Once
all necessary bits have been set as required, the pro-
gramming equipment may read the corresponding iden-
tifier code on Q7~Q0.
TABLE 3. MX29LV002C T/B AUTOSELECT MODE OPERATION
A17 A12
A8
|
A5
|
Description
CE# OE# WE# RESET#
|
|
A9
A6
A1 A0
Q7~Q0
(note) A13 A10
A7
X
A2
X
Manufacture Code
Device ID
L
L
L
L
H
H
H
H
X
X
X
X
VID
VID
L
L
L
L
L
C2H
59H
Read
Silicon
ID
X
X
H
(Top Boot Block)
Device ID
L
L
L
L
H
H
H
H
X
X
X
VID
VID
X
X
L
L
X
X
L
H
L
5AH
01H
(Bottom Boot Block)
Sector Protection Verification
SA
H
(protected)
00H
(unprotected)
NOTE: SA=Sector Address, X=Don't Care, L=Logic Low, H=Logic High.
RESET# pin for 32-TSOP only.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
5
MX29LV002C/002NC T/B
TABLE 4. MX29LV002C T/B COMMAND DEFINITIONS
First Bus
Bus Cycle
Second Bus Third Bus
Fourth Bus
Cycle
Fifth Bus
Cycle
Sixth Bus
Cycle
Command
Cycle
Cycle
Cycle Addr Data Addr
XXXH F0H
RA RD
555H AAH 2AAH 55H 555H 90H ADI
Data Addr
Data Addr Data Addr
Data Addr Data
Reset
1
Read
1
Read Silicon ID
Sector Protect
Verify
4
4
DDI
555H AAH 2AAH 55H 555H 90H (SA) 00H
x02H 01H
Program
4
6
6
1
1
555H AAH 2AAH 55H 555H A0H PA
PD
Chip Erase
555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H
555H 10H
SA 30H
Sector Erase
Sector Erase Suspend
Sector Erase Resume
555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H
XXXH B0H
XXXH 30H
Notes:
1. ADI = Address of Device identifier; A1=0, A0 = 0 for manufacturer code,A1=0, A0 = 1 for device code. A2-A17=do
not care.
(Refer to table 3)
DDI = Data of Device identifier : C2H for manufacture code, 59H/5AH (Top/Bottom) for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2. PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector to be erased.
3. The system should generate the following address patterns: 555H or 2AAH to Address A11~A0.
Address bit A12~A18=X=Don't care for all address commands except for Program Address (PA) and Sector
Address (SA). Write Sequence may be initiated with A12~A18 in either state.
4. For Sector ProtectVerify operation:If read out data is 01H, it means the sector has been protected. If read out data
is 00H, it means the sector is still not being protected.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
6
MX29LV002C/002NC T/B
COMMAND DEFINITIONS
read mode. Table 4 defines the valid register command
sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the
Sector Erase operation is in progress.
Device operations are selected by writing specific ad-
dress and data sequences into the command register.
Writing incorrect address and data values or writing them
in the improper sequence will reset the device to the
TABLE 5. MX29LV002C T/B BUS OPERATION
RE-
ADDRESS
DESCRIPTION
CE# OE# WE# SET# A17 A12 A9 A8 A6 A5 A1 A0
Q0~Q7
(8)
H
H
L
A13 A10
A7
AIN
AIN
X
A2
Read
Write
Reset
L
L
L
H
X
H
L
Dout
DIN(3)
High Z
X
X
Temporary sector unlock
Output Disable
Standby
X
X
H
X
X
H
X
VID
H
AIN
X
DIN
L
VCC±
0.3V
L
High Z
High Z
VCC±
0.3V
VID
VID
H
X
Sector Protect
H
H
L
L
L
SA
X
X
X
X
X
X
X
X
X
L
H
L
X
X
X
H
H
H
L
L
L
DIN
DIN
Chip Unprotect
L
Sector ProtectionVerify
L
H
SA
VID
CODE(5)
Notes:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer toTable 4.
2. VID is the Silicon-ID-Read high voltage, 11.5V to 12.5V.
3. Refer to Table 4 for valid Data-In during a write operation.
4. X can be VIL or VIH.
5. Code=00H means unprotected.
Code=01H means protected.
6. A18~A13=Sector address for sector protect.
7. The sector protect and chip unprotect functions may also be implemented via programming equipment.
8. RESET# pin for 32-TSOP package type only.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
7
MX29LV002C/002NC T/B
REQUIREMENTS FOR READING ARRAY
STANDBY MODE
DATA
When using both pins of CE# and RESET#, the device
enter CMOS Standby with both pins held at Vcc± 0.3V.
The RESET# pin is provided only for 40-pinTSOP pack-
age type. If CE# and RESET# are held at VIH, but not
within the range of VCC ± 0.3V, the device will still be in
the standby mode, but the standby current will be larger.
During Auto Algorithm operation, Vcc active current
(Icc2) is required even CE# = "H" until the operation is
completed. The device can be read with standard ac-
cess time (tCE) from either of these standby modes,
before it is ready to read data.
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control
and gates array data to the output pins.WE# should remain
at VIH.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory content
occurs during the power transition. No command is
necessary in this mode to obtain array data. Standard
microprocessor read cycles that assert valid address on
the device address inputs produce valid data on the device
data outputs.The device remains enabled for read access
until the command register contents are altered.
OUTPUT DISABLE
With the OE# input at a logic high level (VIH), output
from the devices are disabled.This will cause the output
pins to be in a high impedance state.
WRITE COMMANDS/COMMAND SEQUENCES
RESET# OPERATION (for 32-TSOP package type)
To program data to the device or erase sectors of memory
, the system must drive WE# and CE# to VIL, and OE#
to VIH.
The RESET# pin provides a hardware method of resetting
the device to reading array data.When the RESET# pin
is driven low for at least a period of tRP, the device
immediately terminates any operation in progress,
tristates all output pins, and ignores all read/write
commands for the duration of the RESET# pulse. The
device also resets the internal state machine to reading
array data.The operation that was interrupted should be
reinitiated once the device is ready to accept another
command sequence, to ensure data integrity
An erase operation can erase one sector, multiple sectors
, or the entire device.Table indicates the address space
that each sector occupies. A "sector address" consists
of the address bits required to uniquely select a sector.
The "Writing specific address and data commands or
sequences into the command register initiates device
operations. Table 1 defines the valid register command
sequences.Writing incorrect address and data values or
writing them in the improper sequence resets the device
to reading array data. Section has details on erasing a
sector or the entire chip, or suspending/resuming the erase
operation.
Current is reduced for the duration of the RESET# pulse.
When RESET# is held at VSS±0.3V, the device draws
CMOS standby current (ICC4).If RESET# is held atVIL
but not within VSS±0.3V, the standby current will be
greater.
After the system writes the autoselect command
sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the internal
register (which is separate from the memory array) on
Q7-Q0. Standard read cycle timings apply in this mode.
Refer to the Autoselect Mode and Autoselect Command
Sequence section for more information.
The RESET# pin may be tied to system reset circuitry.
A system reset would that also reset the Flash memory,
enabling the system to read the boot-up firm-ware from
the Flash memory.
If RESET# is asserted during a program or erase
operation, the RY/BY# pin remains a "0" (busy) until the
internal reset operation is complete, which requires a time
of tREADY (during Embedded Algorithms).The system
can thus monitor RY/BY# to determine whether the reset
ICC2 in the DC Characteristics table represents the active
current specification for the write mode. The "AC
Characteristics" section contains timing specification table
and timing diagrams for write operations.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
8
MX29LV002C/002NC T/B
operation is complete. If RESET# is asserted when a
sector erase command 30H.
program or erase operation is completed within a time of
tREADY (not during Embedded Algorithms).The system
can read data tRH after the RESET# pin returns toVIH.
The Automatic Chip Erase does not require the device to
be entirely pre-programmed prior to executing the Auto-
matic Chip Erase. Upon executing the Automatic Chip
Erase, the device will automatically program and verify
the entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero pat-
tern, a self-timed chip erase and verify begin. The erase
and verify operations are completed when the data on
Q7 is "1" at which time the device returns to the Read
mode. The system is not required to provide any control
or timing during these operations.
Refer to the AC Characteristics tables for RESET#
parameters and to Figure 24 for the timing diagram.
READ/RESET COMMAND
The read or reset operation is initiated by writing the read/
reset command sequence into the command register.
Microprocessor read cycles retrieve array data. The de-
vice remains enabled for reads until the command regis-
ter contents are altered.
When using the Automatic Chip Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array(no
erase verification command is required).
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid com-
mand must then be written to place the device in the
desired state.
If the Erase operation was unsuccessful, the data on Q5
is "1"(see Table 7), indicating the erase operation ex-
ceed internal timing limit.
The automatic erase begins on the rising edge of the last
WE# or CE# pulse, whichever happens first in the com-
mand sequence and terminates when the data on Q7 is
"1" and the data on Q6 stops toggling for two consecu-
tive read cycles, at which time the device returns to the
Read mode.
SILICON-ID READ COMMAND
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manu-
facturer and device codes must be accessible while the
device resides in the target system. PROM program-
mers typically access signature codes by raising A9 to
a high voltage (VID). However, multiplexing high voltage
onto address lines is not generally desired system de-
sign practice.
The MX29LV002C T/B contains a Silicon-ID-Read op-
eration to supple traditional PROM programming meth-
odology. The operation is initiated by writing the read
silicon ID command sequence into the command regis-
ter. Following the command write, a read cycle with
A1=VIL, A0=VIL retrieves the manufacturer code of C2H.
A read cycle with A1=VIL, A0=VIH returns the device
code of 59H for MX29LV002CT, 5AH for MX29LV002CB.
SET-UP AUTOMATIC CHIP/SECTOR ERASE
COMMANDS
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cycles
are then followed by the chip erase command 10H or
P/N:PM1204
REV. 1.0, JUN. 30, 2005
9
MX29LV002C/002NC T/B
TABLE 6. EXPANDED SILICON ID CODE
Pins
A0
A1
Q7 Q6
Q5
0
Q4
0
Q3
0
Q2
0
Q1
1
Q0
0
Code(Hex)
C2H
Manufacture code
Device code
VIL VIL
VIH VIL
1
1
1
0
1
1
1
0
0
1
59H
for MX29LV002CT
Device code
VIH VIL
1
0
1
1
1
0
1
0
5AH
for MX29LV002CB
Sector Protection
Verification
X
X
VIH
VIH
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
01H (Protected)
00H (Unprotected)
READING ARRAY DATA
RESET COMMAND
The device is automatically set to reading array data
after device power-up.No commands are required to re-
trieve data.The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
Writing the reset command to the device resets the de-
vice to reading array data.Address bits are don't care for
this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data.Once erasure begins, however, the device ignores
reset commands until the operation is complete.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. Af-
ter completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See "Erase Suspend/
Erase Resume Commands" for more infor-mation on this
mode.
The reset command may be written between the se-
quence cycles in a program command sequence be-fore
programming begins. This resets the device to reading
array data (also applies to programming in Erase Sus-
pend mode). Once programming begins, however, the
device ignores reset commands until the operation is
complete.
The system must issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the autoselect mode.See the "Reset Command"
section, next.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command se-
quence.Once in the SILICON ID READ mode, the reset
command must be written to return to reading array data
(also applies to SILICON ID READ during Erase Sus-
pend).
If Q5 goes high during a program or erase operation, writ-
ing the reset command returns the device to reading ar-
ray data (also applies during Erase Suspend).
P/N:PM1204
REV. 1.0, JUN. 30, 2005
10
MX29LV002C/002NC T/B
SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the de-
vice to be entirely pre-programmed prior to executing
the Automatic Sector Erase Set-up command and Au-
tomatic Sector Erase command. Upon executing the
Automatic Sector Erase command, the device will auto-
matically program and verify the sector(s) memory for
an all-zero data pattern. The system is not required to
provide any control or timing during these operations.
(no erase verification command is required). Sector erase
is a six-bus cycle operation. There are two "unlock" write
cycles. These are followed by writing the set-up com-
mand 80H. Two more "unlock" write cycles are then fol-
lowed by the sector erase command 30H. The sector
address is latched on the falling edge of WE# or CE#,
whichever happens later, while the command (data) is
latched on the rising edge of WE# or CE#, whichever
happens first. Sector addresses selected are loaded
into internal register on the sixth falling edge of WE# or
CE#, whichever happens later. Each successive sector
load cycle started by the falling edge of WE# or CE#,
whichever happens later must begin within 50us from
the rising edge of the preceding WE# or CE#, whichever
happens first. Otherwise, the loading period ends and
internal auto sector erase cycle starts. (Monitor Q3 to
determine if the sector erase timer window is still open,
see section Q3, Sector EraseTimer.) Any command other
than Sector Erase(30H) or Erase Suspend(B0H) during
the time-out period resets the device to read mode.
When the sector(s) is automatically verified to contain
an all-zero pattern, a self-timed sector erase and verify
begin. The erase and verify operations are complete
when the data on Q7 is "1" and the data on Q6 stops
toggling for two consecutive read cycles, at which time
the device returns to the Read mode. The system is not
required to provide any control or timing during these
operations.
When using the Automatic sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
Table 7. Write Operation Status
Status
Q7
Q6
Q5
Q3
Q2 RY/BY#
(Note1)
(Note2)
Byte Program in Auto Program Algorithm
Auto Erase Algorithm
Q7# Toggle
0
N/A
1
No
0
Toggle
0
1
Toggle
0
0
Toggle
0
1
Erase Suspend Read
(Erase Suspended Sector)
No
Toggle
N/A Toggle
In Progress
Erase Suspended Mode
Erase Suspend Read
Data
Data Data Data Data
1
0
0
(Non-Erase Suspended Sector)
Erase Suspend Program
Q7# Toggle
Q7# Toggle
0
1
N/A N/A
Byte Program in Auto Program Algorithm
N/A
1
No
Toggle
Exceeded
Time Limits Auto Erase Algorithm
0
Toggle
1
1
Toggle
0
0
Erase Suspend Program
Q7# Toggle
N/A N/A
Note:
1. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
2. Q5 switches to '1' when an Auto Program or Auto Erase operation has exceeded the maximum timing limits.
See "Q5:Exceeded Timing Limits " for more information.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
11
MX29LV002C/002NC T/B
ing edge, and data are internally latched on the rising
edge of the WE# or CE#, whichever happens first. The
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. When the Erase Suspend com-
mand is written during a sector erase operation, the de-
vice requires a maximum of 20us to suspend the erase
operations.However, When the Erase Suspend command
is written during the sector erase time-out, the device
immediately terminates the time-out period and suspends
the erase operation. After this command has been ex-
ecuted, the command register will initiate erase suspend
mode. The state machine will return to read mode auto-
matically after suspend is ready. At this time, state ma-
chine only allows the command register to respond to
the Read Memory Array, Erase Resume and program
commands.
rising edge of WE# or CE#, whichever happens first,
also begins the programming operation. The system is
not required to provide further controls or timings. The
device will automatically provide an adequate internally
generated program pulse and verify margin.
The device provides Q2, Q3, Q5, Q6, Q7, and RY/BY#
to determine the status of a write operation. If the pro-
gram operation was unsuccessful, the data on Q5 is
"1"(seeTable 7), indicating the program operation exceed
internal timing limit.The automatic programming opera-
tion is completed when the data read on Q6 stops tog-
gling for two consecutive read cycles and the data on Q7
and Q6 are equivalent to data written to these two bits,
at which time the device returns to the Read mode(no
program verify command is required).
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended sectors.
BYTE PROGRAM COMMAND SEQUENCE
The device programs one byte of data for each program
operation. The command sequence requires four bus
cycles, and is initiated by writing two unlock write cycles,
followed by the program set-up command. The program
address and data are written next, which in turn initiate
the Embedded Program algorithm. The system is not
required to provide further controls or timings. The device
automatically generates the program pulses and verifies
the programmed cell margin. Table 1 shows the address
and data requirements for the byte program command
sequence.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.However,
a 10ms time delay must be required after the erase re-
sume command, if the system implements an endless
erase suspend/resume loop, or the number of erase sus-
pend/resume is exceeded 1024 times.The erase times
will be expended if the erase behavior always be sus-
pended. (Please refer to MXIC Flash Application Note
for details.)
When the Embedded Program algorithm is complete,
the device then returns to reading array data and
addresses are no longer latched. The system can
determine the status of the program operation by using
Q7, Q6, or RY/BY#. See "Write Operation Status" for
information on these status bits.
Any commands written to the device during the Em-
bedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the programming
operation. The Byte Program command sequence should
be reinitiated once the device has reset to reading array
data, to ensure data integrity.
AUTOMATIC PROGRAM COMMANDS
To initiate Automatic Program mode, A three-cycle com-
mand sequence is required. There are two "unlock" write
cycles. These are followed by writing the Automatic Pro-
gram command A0H.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
"0" back to a "1". Attempting to do so may halt the
operation and set Q5 to "1", or cause the Data# Polling
algorithm to indicate the operation was successful.
However, a succeeding read will show that the data is
Once the Automatic Program command is initiated, the
next WE# pulse causes a transition to an active pro-
gramming operation. Addresses are latched on the fall-
P/N:PM1204
REV. 1.0, JUN. 30, 2005
12
MX29LV002C/002NC T/B
still "0". Only erase operations can convert a "0" to a
"1".
unprotected sectors, and ignores the selected sectors
that are protected.
When the system detects Q7 has changed from the
complement to true data, it can read valid data at Q7-Q0
on the following read cycles. This is because Q7 may
change asynchronously with Q0-Q6 while Output En-
able (OE#) is asserted low.
WRITE OPERATION STATUS
The device provides several bits to determine the sta-
tus of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/
BY#. Table 10 and the following subsections describe
the functions of these bits. Q7, RY/BY#, and DQ6 each
offer a method for determining whether a program or erase
operation is complete or in progress. These three bits
are discussed first. Please note that RY/BY# pin is pro-
vided for 40-pin TSOP package type only.
RY/BY#:Ready/Busy# (for 32-pin TSOP package
only)
The RY/BY# is a dedicated, open-drain output pin that
indicates whether an Automatic Erase/Program algorithm
is in progress or complete. The RY/BY# status is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence.Since RY/BY#
is an open-drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc.
Q7: Data# Polling
The Data# Polling bit, Q7, indicates to the host sys-tem
whether an Automatic Algorithm is in progress or com-
pleted, or whether the device is in Erase Suspend.Data#
Polling is valid after the rising edge of the finalWE# pulse
in the program or erase command sequence.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the de-
vice is ready to read array data (including during the
Erase Suspend mode), or is in the standby mode.
During the Automatic Program algorithm, the device out-
puts on Q7 the complement of the datum programmed
to Q7.This Q7 status also applies to programming dur-
ing Erase Suspend.When the Automatic Program algo-
rithm is complete, the device outputs the datum pro-
grammed to Q7.The system must provide the program
address to read valid status information on Q7. If a pro-
gram address falls within a protected sector, Data# Poll-
ing on Q7 is active for approximately 1 us, then the de-
vice returns to reading array data.
Table 7 shows the outputs for RY/BY# during write op-
eration.
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence (prior to the
program or erase operation), and during the sector time-
out.
During the Automatic Erase algorithm, Data# Polling pro-
duces a "0" on Q7. When the Automatic Erase algo-
rithm is complete, or if the device enters the Erase Sus-
pend mode, Data# Polling produces a "1" on Q7.This is
analogous to the complement/true datum out-put de-
scribed for the Automatic Program algorithm: the erase
function changes all the bits in a sector to "1" prior to
this, the device outputs the "complement," or "0". The
system must provide an address within any of the sec-
tors selected for erasure to read valid status information
on Q7.
During an Automatic Program or Erase algorithm opera-
tion, successive read cycles to any address cause Q6
to toggle. The system may use either OE# or CE# to
control the read cycles.When the operation is complete,
Q6 stops toggling.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data# Polling on
Q7 is active for approximately 100 us, then the device
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Q6 toggles and
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
P/N:PM1204
REV. 1.0, JUN. 30, 2005
13
MX29LV002C/002NC T/B
unprotected sectors, and ignores the selected sectors
that are protected.
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on Q7-Q0 on the following read cycle.
The system can use Q6 and Q2 together to determine
whether a sector is actively erasing or is erase sus-
pended.When the device is actively erasing (that is, the
Automatic Erase algorithm is in progress), Q6 toggling.
When the device enters the Erase Suspend mode, Q6
stops toggling. However, the system must also use Q2
to determine which sectors are erasing or erase-sus-
pended. Alternatively, the system can use Q7.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of Q5 is high
(see the section on Q5). If it is, the system should then
determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as Q5 went
high. If the toggle bit is no longer toggling, the device
has successfully completed the program or erase op-
eration. If it is still toggling, the device did not complete
the operation successfully, and the system must write
the reset command to return to reading array data.
If a program address falls within a protected sector, Q6
toggles for approximately 2 us after the program com-
mand sequence is written, then returns to reading array
data.
Q6 also toggles during the erase-suspend-program mode,
and stops toggling once the Automatic Program algo-
rithm is complete.
The remaining scenario is that system initially determines
that the toggle bit is toggling and Q5 has not gone high.
The system may continue to monitor the toggle bit and
Q5 through successive read cycles, determining the sta-
tus as described in the previous paragraph. Alterna-
tively, it may choose to perform other system tasks. In
this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation.
Table 7 shows the outputs for Toggle Bit I on Q6.
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whether a particular sector is actively erasing (that is,
the Automatic Erase algorithm is in process), or whether
that sector is erase-suspended. Toggle Bit II is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence.
Q5
ExceededTiming Limits
Q5 will indicate if the program or erase time has ex-
ceeded the specified limits (internal pulse count). Under
these conditions Q5 will produce a "1". This time-out
condition indicates that the program or erase cycle was
not successfully completed. Data# Polling and Toggle
Bit are the only operating functions of the device under
this condition.
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE# or CE# to control the read
cycles.) But Q2 cannot distinguish whether the sector
is actively erasing or is erase-suspended. Q6, by com-
parison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which
sectors are selected for erasure. Thus, both status bits
are required for sectors and mode information. Refer to
Table 7 to compare outputs for Q2 and Q6.
If this time-out condition occurs during sector erase op-
eration, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still func-
tional and may be used for the program or erase opera-
tion. The device must be reset to use other sectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence. This
allows the system to continue to use the other active
sectors in the device.
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
If this time-out condition occurs during the chip erase
P/N:PM1204
REV. 1.0, JUN. 30, 2005
14
MX29LV002C/002NC T/B
operation, it specifies that the entire chip is bad or com-
bination of sectors are bad.
cycles resulting fromVCC power-up and power-down tran-
sition or system noise.
If this time-out condition occurs during the byte program-
ming operation, it specifies that the entire sector con-
taining that byte is bad and this sector maynot be re-
used, (other sectors are still functional and can be re-
used).
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 5ns(typical) on CE# or WE#
will not initiate a write cycle.
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please
note that this is not a device failure condition since the
device was incorrectly used.
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE# = VIL,
CE# = VIH or WE# = VIH. To initiate a write cycle CE#
and WE# must be a logical zero while OE# is a logical
one.
Q3
Sector Erase Timer
POWER SUPPLY DECOUPLING
After the completion of the initial sector erase command
sequence, the sector erase time-out will begin. Q3 will
remain low until the time-out is complete. Data# Polling
andToggle Bit are valid after the initial sector erase com-
mand sequence.
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected be-
tween itsVCC and GND.
If Data# Polling or theToggle Bit indicates the device has
been written with a valid erase command, Q3 may be
used to determine if the sector erase timer window is
still open. If Q3 is high ("1") the internally controlled
erase cycle has begun; attempts to write subsequent
commands to the device will be ignored until the erase
operation is completed as indicated by Data# Polling or
Toggle Bit. If Q3 is low ("0"), the device will accept
additional sector erase commands. To insure the com-
mand has been accepted, the system software should
check the status of Q3 prior to and following each sub-
sequent sector erase command. If Q3 were high on the
second status check, the command may not have been
accepted.
POWER-UP SEQUENCE
The MX29LV002CT/B powers up in the Read only mode.
In addition, the memory contents may only be altered
after successful completion of the predefined command
sequences.
TEMPORARY SECTOR UNPROTECT
This feature allows temporary unprotection of previously
protected sector to change data in-system.TheTempo-
rary Sector Unprotect mode is activated by setting the
RESET# pin toVID(11.5V-12.5V). During this mode, for-
merly protected sectors can be programmed or erased
as un-protected sector. Once VID is remove from the
RESET# pin, all the previously protected sectors are pro-
tected again.
DATA PROTECTION
The MX29LV002C T/B is designed to offer protection
against accidental erasure or programming caused by
spurious system level signals that may exist during power
transition. During power up the device automatically re-
sets the state machine in the Read mode. In addition,
with its control register architecture, alteration of the
memory contents only occurs after successful comple-
tion of specific command sequences. The device also
incorporates several features to prevent inadvertent write
SECTOR PROTECTION
The MX29LV002CT/B features hardware sector protec-
tion. This feature will disable both program and erase
operations for these sectors protected. To activate this
mode, the programming equipment must force VID on
address pin A9 and OE# (suggestVID = 12V). Program-
P/N:PM1204
REV. 1.0, JUN. 30, 2005
15
MX29LV002C/002NC T/B
ming of the protection circuitry begins on the falling edge
of the WE# pulse and is terminated on the rising edge.
Please refer to sector protect algorithm and waveform.
To verify programming of the protection circuitry, the pro-
gramming equipment must forceVID on address pin A9
( with CE# and OE# at VIL and WE# at VIH). When
A1=VIH, A0=VIL, A6=VIL, it will produce a logical "1"
code at device output Q0 for a protected sector. Other-
wise the device will produce 00H for the unprotected sec-
tor. In this mode, the addresses, except for A1, are don't
care. Address locations with A1 = VIL are reserved to
read manufacturer and device codes.(Read Silicon ID)
It is also possible to determine if the sector is protected
in the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
CHIP UNPROTECT
The MX29LV002C T/B also features the chip unprotect
mode, so that all sectors are unprotected after chip
unprotectiscompletedtoincorporateanychangesinthe
code. It is recommended to protect all sectors before
activating chip unprotect mode.
Toactivatethismode,theprogrammingequipmentmust
force VID on control pin OE# and address pin A9. The
CE# pins must be set at VIL. Pins A6 must be set to
VIH.(seeTable2) Refertochipunprotect algorithmand
waveform for the chip unprotect algorithm. The
unprotectionmechanismbeginsonthefallingedgeofthe
WE# pulse and is terminated on the rising edge.
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
PerformingareadoperationwithA1=VIH,itwillproduce
00H at data outputs(Q0-Q7) for an unprotected sector.
It is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
16
MX29LV002C/002NC T/B
OPERATING RATINGS
ABSOLUTE MAXIMUM RATINGS
StorageTemperature
Commercial (C) Devices
Plastic Packages . . . . . . . . . . . . . ..... -65oC to +150oC
Ambient Temperature (TA ). . . . . . . . . . . . 0° C to +70°C
Industrial (I) Devices
AmbientTemperature
with Power Applied. . . . . . . . . . . . . .... -65oC to +125oC
Voltage with Respect to Ground
Ambient Temperature (TA ). . . . . . . . . . -40° C to +85°C
VCC Supply Voltages
VCC for full voltage range. . . . . . . . . . . +2.7 V to 3.6 V
VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V
A9, OE#, and
Operating ranges define those limits between which the
functionality of the device is guaranteed.
RESET# (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5 V.
During voltage transitions, input or I/O pins may over-
shoot VSS to -2.0 V for periods of up to 20 ns. Maxi-
mum DC voltage on input or I/O pins is VCC +0.5 V.
During voltage transitions, input or I/O pins may over-
shoot to VCC +2.0 V for periods up to 20 ns.
2.Minimum DC input voltage on pins A9, OE#, and RE-
SET# is -0.5 V. During voltage transitions, A9, OE#,
and RESET# may overshootVSS to -2.0V for periods
of up to 20 ns.Maximum DC input voltage on pin A9 is
+12.5V which may overshoot to 14.0V for periods up
to 20 ns.The RESET# pin is provided for 40-pinTSOP
package type.
3.No more than one output may be shorted to ground at
a time.Duration of the short circuit should not be greater
than one second.
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device at these or any other conditions above those indi-
cated in the operational sections of this data sheet is not
implied. Exposure of the device to absolute maximum
rating conditions for extended periods may affect device
reliability.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
17
MX29LV002C/002NC T/B
Table 8. CAPACITANCE TA = 25oC, f = 1.0 MHz
SYMBOL PARAMETER
MIN.
TYP
MAX.
8
UNIT
pF
CONDITIONS
VIN = 0V
CIN1
CIN2
COUT
Input Capacitance
Control Pin Capacitance
Output Capacitance
12
pF
VIN = 0V
12
pF
VOUT = 0V
Table 9. DC CHARACTERISTICS TA = -40oC to 85oC, VCC = 2.7V to 3.6V
Symbol PARAMETER
MIN.
TYP
MAX.
± 1
35
± 1
12
4
UNIT
uA
CONDITIONS
ILI
Input Leakage Current
VIN = VSS to VCC
ILIT
ILO
ICC1
A9 Input Leakage Current
Output Leakage Current
VCC Active Read Current
uA
VCC=VCC max; A9=12.5V
VOUT = VSS to VCC, VCC=VCC max
CE#=VIL, OE#=VIH @5MHz
@1MHz
uA
7
2
mA
mA
mA
uA
ICC2
ICC3
VCC Active write Current
VCC Standby Current
15
0.2
30
5
CE#=VIL, OE#=VIH
CE#; RESET#=VCC ± 0.3V
(RESET# pin for 40-TSOP)
RESET#=VSS ± 0.3V
ICC4
VCC Standby Current
During Reset
0.2
0.2
5
uA
(RESET# pin for 40-TSOP)
VIH=VCC ± 0.3V; VIL=VSS ± 0.3V
ICC5
VIL
Automatic sleep mode
Input Low Voltage(Note 1)
Input High Voltage
Voltage for Automatic
Select and Temporary
Chip Unprotect
5
uA
V
-0.5
0.8
VIH
VID
0.7xVCC
VCC+ 0.3
V
11.5
12.5
0.45
V
V
VCC=3.3V
VOL
Output Low Voltage
Output High Voltage(TTL)
Output High Voltage
(CMOS)
IOL = 4.0mA, VCC= VCC min
IOH = -2mA, VCC=VCC min
IOH = -100uA, VCC min
VOH1
VOH2
0.85xVCC
VCC-0.4
NOTES:
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. Automatic sleep mode enable the low power mode when addresses remain stable for tACC +30ns.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
18
MX29LV002C/002NC T/B
AC CHARACTERISTICS
TA = -40oC to 85oC, VCC = 2.7V~3.6V
Table 10. READ OPERATIONS
29LV002CT/B-70
29LV002CT/B-90
SYMBOL PARAMETER
MIN.
MAX.
70
MIN.
MAX.
90
UNIT CONDITIONS
tRC
tACC
tCE
Read Cycle Time (Note 1)
Address to Output Delay
CE# to Output Delay
ns
70
90
ns
ns
ns
ns
ns
ns
CE#=OE#=VIL
OE#=VIL
70
90
tOE
OE# to Output Delay
30
35
CE#=VIL
tDF
OE# High to Output Float (Note1)
Output Enable Read
0
25
0
30
CE#=VIL
tOEH
0
0
Hold Time
Toggle and
10
10
Data# Polling
tOH
Address to Output hold
0
0
ns
CE#=OE#=VIL
NOTE:
1. Not 100% tested.
TEST CONDITIONS:
• Input pulse levels: 0V/3.0V.
2. tDF is defined as the time at which the output achieves
the open circuit condition and data is no longer driven.
• Input rise and fall times is equal to or less than 5ns.
• Outputload:1TTLgate+100pF(Includingscopeand
jig),for29LV002CT/B-90.1TTL gate+30pF(Including
scope and jig) for 29LV002CT/B-70.
• Reference levels for measuring timing: 1.5V.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
19
MX29LV002C/002NC T/B
Figure 1. SWITCHING TEST CIRCUITS
DEVICE UNDER
TEST
2.7K ohm
+3.3V
CL
6.2K ohm
DIODES=IN3064
OR EQUIVALENT
CL=100pF Including jig capacitance
CL=30pF for MX29LV004T/B-70
Figure 2. SWITCHING TEST WAVEFORMS
3.0V
1.5V
TEST POINTS
1.5V
0V
INPUT
OUTPUT
AC TESTING: Inputs are driven at 3.0V for a logic "1" and 0V for a logic "0".
Input pulse rise and fall times are < 5ns.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
20
MX29LV002C/002NC T/B
Figure 3. READ TIMING WAVEFORMS
tRC
VIH
VIL
ADD Valid
Addresses
tACC
tCE
VIH
VIL
CE#
VIH
VIL
WE#
tOE
tDF
tOEH
VIH
VIL
OE#
Outputs
RESET#
tACC
tOH
HIGH Z
HIGH Z
VOH
VOL
DATA Valid
VIH
VIL
P/N:PM1204
REV. 1.0, JUN. 30, 2005
21
MX29LV002C/002NC T/B
AC CHARACTERISTICS
TA = -40oC to 85oC, VCC = 2.7V~3.6V
Table 11. Erase/Program Operations
29LV002CT/B-70
29LV002CT/B-90
SYMBOL PARAMETER
MIN.
70
0
MAX.
MIN.
90
0
MAX.
UNIT
ns
tWC
tAS
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
ns
tAH
45
35
0
45
45
0
ns
tDS
Data Setup Time
ns
tDH
Data Hold Time
ns
tOES
tGHWL
Output Enable Setup Time
Read Recovery Time Before Write
(OE# High to WE# Low)
CE# Setup Time
0
0
ns
0
0
ns
tCS
0
0
ns
ns
ns
ns
us
tCH
CE# Hold Time
0
0
tWP
tWPH
Write Pulse Width
35
35
Write Pulse Width High
30
30
tWHWH1 ProgrammingOperation(Note2)
(Byte/Wordprogramtime)
9(Typ.)
9(Typ.)
tWHWH2 Sector Erase Operation (Note 2)
0.7(Typ.)
0.7(Typ.)
sec
us
tVCS
tRB
VCC Setup Time (Note 1)
50
0
50
0
Recovery Time from RY/BY#
Program/Erase Vaild to RY/BY# Delay
Write Pulse Width for Sector Protect
(A9, OE#Control)
ns
tBUSY
tWPP1
90
90
ns
100ns
10us
(Typ.)
12ms
(Typ.)
50
100ns
100ns
10us
(Typ.)
12ms
(Typ.)
50
tWPP2
Write Pulse Width for Sector Unprotect
(A9, OE#Control)
100nss
tBAL
Sector Address Load Time
us
NOTES:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
3. RY/BY# pin is provided for 32-TSOP.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
22
MX29LV002C/002NC T/B
AC CHARACTERISTICS
TA = -40oC to 85oC,VCC = 2.7V~3.6V
Table 12. Alternate CE# Controlled Erase/Program Operations
29LV002CT/B-70
29LV002CT/B-90
SYMBOL PARAMETER
MIN.
MAX.
MIN.
MAX.
UNIT
ns
tWC
tAS
Write CycleTime (Note 1)
70
90
Address SetupTime
Address HoldTime
Data SetupTime
0
0
ns
tAH
45
45
ns
tDS
35
45
ns
tDH
Data HoldTime
0
0
ns
tOES
tGHEL
tWS
tWH
tCP
Output Enable SetupTime
Read RecoveryTime BeforeWrite
WE# SetupTime
0
0
ns
0
0
ns
0
0
ns
WE# HoldTime
0
0
ns
CE# PulseWidth
35
35
ns
tCPH
CE# Pulse Width High
30
30
ns
tWHWH1 Programming Operation(note2)
tWHWH2 Sector Erase Operation (note2)
9(Typ.)
0.7(Typ.)
9(Typ.)
0.7(Typ.)
us
sec
NOTE:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
23
MX29LV002C/002NC T/B
Figure 4. COMMAND WRITE TIMING WAVEFORM
VCC
3V
VIH
VIL
Addresses
ADD Valid
tAH
tAS
VIH
VIL
WE#
CE#
tOES
tWPH
tWP
tCWC
VIH
VIL
tCS
tCH
tDH
VIH
VIL
OE#
Data
tDS
VIH
VIL
DIN
P/N:PM1204
REV. 1.0, JUN. 30, 2005
24
MX29LV002C/002NC T/B
AUTOMATIC PROGRAMMING TIMING WAVEFORM
after automatic programming starts. Device outputs
DATA# during programming and DATA after programming
on Q7.(Q6 is for toggle bit; see toggle bit, Data# Polling,
timing waveform)
One byte data is programmed. Verify in fast algorithm
and additional verification by external control are not re-
quired because these operations are executed automati-
cally by internal control circuit. Programming completion
can be verified by Data# Polling and toggle bit checking
Figure 5. AUTOMATIC PROGRAMMING TIMING WAVEFORM
Program Command Sequence(last two cycle)
Read Status Data (last two cycle)
tWC
tAS
PA
PA
555h
PA
Address
CE#
tAH
tCH
tGHWL
OE#
WE#
tWHWH1
tWP
tCS
tWPH
tDS tDH
Status
A0h
PD
DOUT
Data
tBUSY
tRB
RY/BY#
tVCS
VCC
NOTES:
1.PA=Program Address, PD=Program Data, DOUT is the true data the program address
P/N:PM1204
REV. 1.0, JUN. 30, 2005
25
MX29LV002C/002NC T/B
Figure 6. AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Write Program Data/Address
Data Poll
Increment
Address
from system
No
No
Verify Word Ok ?
YES
Last Address ?
YES
Auto Program Completed
P/N:PM1204
REV. 1.0, JUN. 30, 2005
26
MX29LV002C/002NC T/B
Figure 7. CE# CONTROLLED PROGRAM TIMING WAVEFORM
PA for program
555 for program
2AA for erase
SA for sector erase
555 for chip erase
Data# Polling
Address
PA
tWC
tWH
tAS
tAH
WE#
OE#
tGHEL
tCP
tWHWH1 or 2
CE#
Data
tWS
tDS
tCPH
tBUSY
tDH
DOUT
Q7
PD for program
30 for sector erase
10 for chip erase
A0 for program
55 for erase
tRH
RESET#
RY/BY#
NOTES:
1.PA=Program Address, PD=Program Data, DOUT=Data Out, Q7=complement of data written to device.
2.Figure indicates the last two bus cycles of the command sequence.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
27
MX29LV002C/002NC T/B
AUTOMATIC CHIP ERASE TIMING WAVEFORM
All data in chip are erased. External erase verification is
not required because data is verified automatically by
internal control circuit. Erasure completion can be veri-
fied by Data# Polling and toggle bit checking after auto-
matic erase starts. Device outputs 0 during erasure
and 1 after erasure on Q7.(Q6 is for toggle bit;see toggle
bit, Data# Polling, timing waveform)
Figure 8. AUTOMATIC CHIP ERASE TIMING WAVEFORM
Erase Command Sequence(last two cycle)
Read Status Data
VA
tWC
tAS
VA
2AAh
555h
Address
CE#
tAH
tCH
tGHWL
OE#
WE#
tWHWH2
tWP
tCS
tWPH
tDS tDH
In
Progress
55h
10h
Complete
Data
tBUSY
tRB
RY/BY#
tVCS
VCC
NOTES:
SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status").
P/N:PM1204
REV. 1.0, JUN. 30, 2005
28
MX29LV002C/002NC T/B
Figure 9. AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
Data Pall from System
NO
Data=FFh ?
YES
Auto Chip Erase Completed
P/N:PM1204
REV. 1.0, JUN. 30, 2005
29
MX29LV002C/002NC T/B
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Sector indicated by A12 to A17 are erased. External
erase verify is not required because data are verified
automatically by internal control circuit. Erasure comple-
tion can be verified by Data# Polling and toggle bit check-
ing after automatic erase starts. Device outputs 0 dur-
ing erasure and 1 after erasure on Q7.(Q6 is for toggle
bit; see toggle bit, Data# Polling, timing waveform)
Figure 10. AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Erase Command Sequence(last two cycle)
Read Status Data
VA
tWC
tAS
Sector
Sector
Sector
VA
2AAh
Address
CE#
Address 0
Address 1
Address n
tAH
tCH
tGHWL
OE#
WE#
tWHWH2
tBAL
tWP
tCS
tWPH
tDS tDH
In
Progress
55h
30h
30h
30h
Complete
Data
tBUSY
tRB
RY/BY#
tVCS
VCC
NOTES:
SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status").
P/N:PM1204
REV. 1.0, JUN. 30, 2005
30
MX29LV002C/002NC T/B
Figure 11. AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Sector Address
NO
Last Sector
to Erase
YES
Data Poll from System
NO
Data=FFh
YES
Auto Sector Erase Completed
P/N:PM1204
REV. 1.0, JUN. 30, 2005
31
MX29LV002C/002NC T/B
Figure 12. ERASE SUSPEND/ERASE RESUME FLOWCHART
START
Write Data B0H
ERASE SUSPEND
NO
Toggle Bit checking Q6
not toggled
YES
Read Array or
Program
Reading or
NO
Programming End
YES
Write Data 30H
Delay 10ms (note)
Continue Erase
ERASE RESUME
Another
NO
Erase Suspend ?
YES
Note: If the system implements an endless erase suspend/resume loop, or the number of erase suspend/resume is
exceeded 1024 times, then the 10ms time delay must be put into consideration.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
32
MX29LV002C/002NC T/B
Figure 13. IN-SYSTEM SECTOR PROTECT/UNPROTECT TIMING WAVEFORM (RESET# Control)
VID
VIH
RESET#
SA, A6
A1, A0
Valid*
Valid*
Valid*
Sector Protect or Sector Unprotect
Verify
40h
Status
Data
60h
60h
Sector Protect =150us
Sector Unprotect =15ms
1us
CE#
WE#
OE#
Note: When sector protect, A6=0, A1=1, A0=0. When sector unprotect, A6=1, A1=1, A0=0.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
33
MX29LV002C/002NC T/B
Figure 14. IN-SYSTEM SECTOR PROTECTION ALGORITHM WITH RESET#=VID
START
PLSCNT=1
RESET#=VID
Wait 1us
No
Temporary Sector
Unprotect Mode
First Write
Cycle=60H
Yes
Set up sector address
Write 60H to sector address
with A6=0, A1=1, A0=0
Wait 150us
Verify sector protect :
write 40H with A6=0,
A1=1, A0=0
Increment PLSCNT
Reset PLSCNT=1
Read from sector address
No
No
PLSCNT=25?
Data=01H ?
Yes
Yes
Device failed
Yes
Protect another
sector?
No
Remove VID from RESET#
Write reset command
Sector protect complete
P/N:PM1204
REV. 1.0, JUN. 30, 2005
34
MX29LV002C/002NC T/B
Figure 15. SECTOR PROTECT TIMING WAVEFORM (A9, OE# Control)
A1
A6
12V
3V
A9
tVLHT
tVLHT
Verify
12V
3V
OE#
tVLHT
tWPP 1
WE#
CE#
tOESP
Data
01H
F0H
tOE
Sector Address
A18-A12
P/N:PM1204
REV. 1.0, JUN. 30, 2005
35
MX29LV002C/002NC T/B
Figure 16. SECTOR PROTECTION ALGORITHM (A9, OE# Control)
START
Set Up Sector Addr
PLSCNT=1
OE#=VID, A9=VID, CE#=VIL
A6=VIL
Activate WE# Pulse
Time Out 150us
Set WE#=VIH, CE#=OE#=VIL
A9 should remain VID
Read from Sector
Addr=SA, A1=1
No
No
Data=01H?
PLSCNT=32?
Yes
Device Failed
Yes
Protect Another
Sector?
Remove VID from A9
Write Reset Command
Sector Protection
Complete
P/N:PM1204
REV. 1.0, JUN. 30, 2005
36
MX29LV002C/002NC T/B
Figure 17. IN-SYSTEM SECTOR UNPROTECTION ALGORITHM WITH RESET#=VID
START
PLSCNT=1
RESET#=VID
Wait 1us
No
No
Temporary Sector
Unprotect Mode
First Write
Cycle=60H ?
Yes
All sector
Protect all sectors
protected?
Yes
Set up first sector address
Chip unprotect :
write 60H with
A6=1, A1=1, A0=0
Wait 50ms
Verify chip unprotect
write 40H to sector address
with A6=1, A1=1, A0=0
Increment PLSCNT
Read from sector address
with A6=1, A1=1, A0=0
No
No
Set up next sector address
PLSCNT=1000?
Data=00H ?
Yes
Yes
Device failed
Yes
Last sector
verified?
No
Remove VID from RESET#
Write reset command
Chip unprotect complete
P/N:PM1204
REV. 1.0, JUN. 30, 2005
37
MX29LV002C/002NC T/B
Figure 18. TIMING WAVEFORM FOR CHIP UNPROTECTION (A9, OE# Control)
A1
12V
3V
A9
A6
tVLHT
Verify
12V
3V
OE#
tVLHT
tVLHT
tWPP 2
WE#
CE#
tOESP
Data
00H
F0H
tOE
A18-A12
Sector Address
Notes: tWPP1 (Write pulse width for sector protect)=100ns min, 10us(typ.).
tWPP2 (Write pulse width for sector unprotect)=100ns min, 12ms(typ).
P/N:PM1204
REV. 1.0, JUN. 30, 2005
38
MX29LV002C/002NC T/B
Figure 19. CHIP UNPROTECTION ALGORITHM (A9, OE# Control)
START
Protect All Sectors
PLSCNT=1
Set OE#=A9=VID
CE#=VIL, A6=1
Activate WE# Pulse
Time Out 50ms
Increment
PLSCNT
Set OE#=CE#=VIL
A9=VID,A1=1
Set Up First Sector Addr
Read Data from Device
No
No
Data=00H?
Yes
PLSCNT=1000?
Increment
Sector Addr
Yes
Device Failed
No
All sectors have
been verified?
Yes
Remove VID from A9
Write Reset Command
Chip Unprotect
Complete
* It is recommended before unprotect whole chip, all sectors should be protected in advance.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
39
MX29LV002C/002NC T/B
WRITE OPERATION STATUS
Figure 20. DATA# POLLING ALGORITHM
Start
Read Q7~Q0
Add.=VA(1)
Yes
Q7 = Data ?
No
No
Q5 = 1 ?
Yes
Read Q7~Q0
Add.=VA
Yes
Q7 = Data ?
(2)
No
FAIL
Pass
NOTE : 1.VA=Valid address for programming
2.Q7 should be re-checked even Q5="1" because Q7 may change
simultaneously with Q5.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
40
MX29LV002C/002NC T/B
Figure 21. TOGGLE BIT ALGORITHM
Start
Read Q7-Q0
Read Q7-Q0
(Note 1)
NO
Toggle Bit Q6 =
Toggle ?
YES
NO
Q5= 1?
YES
Read Q7~Q0 Twice
(Note 1,2)
NO
Toggle bit Q6=
Toggle?
YES
Program/Erase Operation
Not Complete,Write
Reset Command
Program/Erase
operation Complete
Note:1.Read toggle bit twice to determine whether or not it is toggling.
2. Recheck toggle bit because it may stop toggling as Q5 change to "1".
P/N:PM1204
REV. 1.0, JUN. 30, 2005
41
MX29LV002C/002NC T/B
Figure 22. DATA# POLLING TIMINGS (DURING AUTOMATIC ALGORITHMS)
tRC
VA
VA
VA
Address
CE#
tACC
tCE
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
High Z
Complement
Status Data
Complement
Status Data
True
True
Valid Data
Valid Data
Q7
Q0-Q6
tBUSY
RY/BY#
NOTES:
1. VA=Valid address. Figure shows are first status cycle after command sequence, last status read cycle, and array data read cycle.
2. CE# must be toggled when DATA# polling.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
42
MX29LV002C/002NC T/B
Figure 23. TOGGLE BIT TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS)
tRC
VA
VA
tACC
tCE
VA
VA
Address
CE#
tCH
tOE
OE#
tDF
tOEH
WE#
tOH
High Z
Valid Status
(second read)
Valid Status
(first raed)
Valid Data
Valid Data
Q6/Q2
(stops toggling)
tBUSY
RY/BY#
NOTES:
1. VA=Valid address; not required for Q6. Figure shows first two status cycle after command sequence, last status read cycle,
and array data read cycle.
2. CE# must be toggled when toggle bit toggling.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
43
MX29LV002C/002NC T/B
Table 13. AC CHARACTERISTICS (for 32-pin TSOP package type)
Parameter Std Description
Test Setup All Speed Options Unit
tREADY1
RESET# PIN Low (During Automatic Algorithms)
MAX
20
us
to Read or Write (See Note)
tREADY2
RESET# PIN Low (NOT During Automatic
Algorithms) to Read or Write (See Note)
RESET# Pulse Width (During Automatic Algorithms)
RESET# HighTime Before Read (See Note)
RY/BY# Recovery Time(to CE#, OE# go low)
MAX
500
ns
tRP
tRH
tRB
MIN
MIN
MIN
500
50
0
ns
ns
ns
Note:Not 100% tested
Figure 24. RESET# TIMING WAVEFORM (for 32-pin TSOP package type)
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady2
Reset Timing NOT during Automatic Algorithms
tReady1
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Reset Timing during Automatic Algorithms
P/N:PM1204
REV. 1.0, JUN. 30, 2005
44
MX29LV002C/002NC T/B
Table 14. TEMPORARY SECTOR UNPROTECT
Parameter Std. Description
Test Setup All Speed Options Unit
tVIDR
tRSP
VID Rise and Fall Time (See Note)
RESET# SetupTime forTemporary Sector Unprotect
Min
Min
500
4
ns
us
Note:
Not 100% tested
Figure 25. TEMPORARY SECTOR UNPROTECT TIMING DIAGRAM
12V
RESET#
0 or Vcc
0 or Vcc
Program or Erase Command Sequence
tVIDR
tVIDR
CE#
WE#
tRSP
RY/BY#
Figure 26. Q6 vs Q2 for Erase and Erase Suspend Operations
Enter Embedded
Erasing
Erase
Enter Erase
Erase
Suspend
Suspend Program
Resume
Erase
Erase
Erase Suspend
Read
Erase
Erase
Complete
WE#
Q6
Suspend
Program
Q2
NOTES:
The system can use OE# or CE# to toggle Q2/Q6, Q2 toggles only when read at an address within an erase-suspended
P/N:PM1204
REV. 1.0, JUN. 30, 2005
45
MX29LV002C/002NC T/B
Figure 27. TEMPORARY SECTOR UNPROTECT ALGORITHM
Start
RESET# = VID (Note 1)
Perform Erase or Program Operation
Operation Completed
RESET# = VIH
Temporary Sector Unprotect Completed(Note 2)
Note : 1. All protected sectors are temporary unprotected.
VID=11.5V~12.5V
2. All previously protected sectors are protected again.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
46
MX29LV002C/002NC T/B
Figure 28. ID CODE READ TIMING WAVEFORM
VCC
3V
VID
VIH
VIL
ADD
A9
VIH
VIL
ADD
A0
tACC
tACC
VIH
VIL
A1
ADD
A2-A8
VIH
A10-A18 VIL
CE#
VIH
VIL
VIH
VIL
tCE
WE#
OE#
tOE
VIH
VIL
tDF
tOH
tOH
VIH
VIL
DATA
Q0-Q7
DATA OUT
C2H
DATA OUT
B5H/B6H
P/N:PM1204
REV. 1.0, JUN. 30, 2005
47
MX29LV002C/002NC T/B
RECOMMENDED OPERATING CONDITIONS
At Device Power-Up
AC timing illustrated in Figure A is recommended for the supply voltages and the control signals at device power-up.
If the timing in the figure is ignored, the device may not operate correctly.
VCC(min)
VCC
GND
tVR
tACC
tR or tF
tR or tF
VIH
VIL
Valid
ADDRESS
CE#
Address
tF
tCE
tR
VIH
VIL
VIH
VIL
WE#
tF
tOE
tR
VIH
VIL
OE#
VIH
VIL
WP#/ACC
DATA
VOH
VOL
High Z
Valid
Ouput
Figure A. ACTiming at Device Power-Up
Notes
Symbol
Parameter
Min.
Max.
Unit
us/V
us/V
us/V
tVR
tR
VCC RiseTime
1
20
500000
20
Inptut Signal Rise Time
Inptut Signal Fall Time
1,2
1,2
tF
20
Notes :
1. Sampled, not 100% tested.
2. This specification is applied for not only the device power-up but also the normal operations.
P/N:PM1204
REV. 1.0, JUN. 30, 2005
48
MX29LV002C/002NC T/B
Table 15. ERASE AND PROGRAMMING PERFORMANCE(1)
LIMITS
PARAMETER
MIN.
TYP.(2)
MAX.(3)
15
UNIT
sec
Sector Erase Time
Chip Erase Time
0.7
4
32
sec
Byte Programming Time
Chip Programming Time
Erase/Program Cycles
9
300
us
4.5
13.5
sec
100,000
Cycles
Note: 1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25° C, 3V.
3.Maximum values measured at 25° C, 2.7V.
Table 16. LATCH-UP CHARACTERISTICS
MIN.
-1.0V
MAX.
Input Voltage with respect to GND on all pins except I/O pins
Input Voltage with respect to GND on all I/O pins
Current
12.5V
Vcc + 1.0V
+100mA
-1.0V
-100mA
Includes all pins except Vcc. Test conditions: Vcc = 3.0V, one pin at a time.
Table 17. DATA RETENTION
Parameter Description
Test Conditions
150°C
Min
10
Unit
Years
Years
Data Retention Time
125°C
20
P/N:PM1204
REV. 1.0, JUN. 30, 2005
49
MX29LV002C/002NC T/B
described inTable 18.
QUERY COMMAND AND COMMON FLASH
The single cycle Query command is valid only when the
device is in the Read mode, including Erase Suspend,
Standby mode, and Read ID mode;however, it is ignored
otherwise.
INTERFACE (CFI) MODE ( for MX29LV002CT/
CB)
MX29LV002CT/CB is capable of operating in the CFI
mode. This mode all the host system to determine the
manufacturer of the device such as operating param-
eters and configuration.Two commands are required in
CFI mode. Query command of CFI mode is placed first,
then the Reset command exits CFI mode. These are
The Reset command exits from the CFI mode to the
Read mode, or Erase Suspend mode, or read ID mode.
The command is valid only when the device is in the CFI
mode.
TABLE 18-1. CFI mode: Identification Data Values
(All values in these tables are in hexadecimal)
Description
Address
20
Data
0051
0052
0059
0002
0000
0040
0000
0000
0000
0000
0000
Query-unique ASCII string "QRY"
22
24
Primary vendor command set and control interface ID code
Address for primary algorithm extended query table
26
28
2A
2C
2E
30
Alternate vendor command set and control interface ID code (none)
Address for secondary algorithm extended query table (none)
32
34
TABLE 18-2. CFI Mode: System Interface Data Values
(All values in these tables are in hexadecimal)
Description
Address
36
Data
0027
0036
0000
0000
0004
0000
000A
0000
0005
0000
0004
0000
VCC supply, minimum (2.7V)
VCC supply, maximum (3.6V)
38
VPP supply, minimum (none)
3A
3C
3E
40
VPP supply, maximum (none)
Typical timeout for single word/byte write (2N us)
Typical timeout for Minimum size buffer write (2N us)
Typical timeout for individual block erase (2N ms)
Typical timeout for full chip erase (2N ms)
Maximum timeout for single word/byte write times (2N X Typ)
Maximum timeout for buffer write times (2N X Typ)
Maximum timeout for individual block erase times (2N X Typ)
Maximum timeout for full chip erase times (not supported)
42
44
46
48
4A
4C
P/N:PM1204
REV. 1.0, JUN. 30, 2005
50
MX29LV002C/002NC T/B
TABLE 18-3. CFI Mode: Device Geometry Data Values
(All values in these tables are in hexadecimal)
Description
Address
4E
50
Data
0012
0000
0000
0000
0000
0004
0000
0000
0040
0000
0001
0000
0020
0000
0000
0000
0080
0000
0002
0000
0000
0001
Device size (2N bytes)
Flash device interface code (refer to the CFI publication 100)
52
54
56
58
5A
5C
5E
60
62
64
66
68
6A
6C
6E
70
72
74
76
78
Maximum number of bytes in multi-byte write (not supported)
Number of erase block regions
Erase block region 1 information (refer to the CFI publication 100)
Erase block region 2 information
Erase block region 3 information
Erase block region 4 information
TABLE 18-4. CFI Mode: Primary Vendor-Specific Extended Query Data Values
(All values in these tables are in hexadecimal)
Description
Address
80
Data
0050
0052
0049
0031
0030
0000
0002
0001
0001
0004
0000
0000
0000
Query-unique ASCII string "PRI"
82
84
Major version number, ASCII
86
Minor version number, ASCII
88
Address sensitive unlock (0=required, 1= not required)
Erase suspend (2= to read and write)
Sector protect (N= # of sectors/group)
Temporarysectorunprotected(1=supported)
Sectorprotect/unprotectedscheme
SimultaneousR/Woperation(0=notsupported)
Burst mode type (0=not supported)
Page mode type (0=not supported)
8A
8C
8E
90
92
94
96
98
P/N:PM1204
REV. 1.0, JUN. 30, 2005
51
MX29LV002C/002NC T/B
ORDERING INFORMATION
PART NO.
AccessTime Operating Current Standby Current
PACKAGE
Remark
(ns)
70
70
90
90
70
70
90
90
70
70
70
70
70
70
70
70
70
90
70
90
70
90
70
90
70
90
70
90
70
90
70
90
MAX. (mA)
30
MAX. (uA)
MX29LV002CTTC-70
MX29LV002CBTC-70
MX29LV002CTTC-90
MX29LV002CBTC-90
MX29LV002CTTI-70
MX29LV002CBTI-70
MX29LV002CTTI-90
MX29LV002CBTI-90
MX29LV002CTQC-70
MX29LV002CBQC-70
MX29LV002CTQC-90
MX29LV002CBQC-90
MX29LV002CTQI-70
MX29LV002CBQI-70
MX29LV002CTQI-90
MX29LV002CBQI-90
MX29LV002CTTC-70G
MX29LV002CTTC-90G
MX29LV002CBTC-70G
MX29LV002CBTC-90G
MX29LV002CTTI-70G
MX29LV002CTTI-90G
MX29LV002CBTI-70G
MX29LV002CBTI-90G
MX29LV002CTQC-70G
MX29LV002CTQC-90G
MX29LV002CBQC-70G
MX29LV002CBQC-90G
MX29LV002CTQI-70G
MX29LV002CTQI-90G
MX29LV002CBQI-70G
MX29LV002CBQI-90G
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
P/N:PM1204
REV. 1.0, JUN. 30, 2005
52
MX29LV002C/002NC T/B
PART NO.
AccessTime Operating Current Standby Current
PACKAGE
Remark
(ns)
70
70
90
90
70
70
90
90
70
70
70
70
70
70
70
70
70
90
70
90
70
90
70
90
70
90
70
90
70
90
70
90
MAX. (mA)
30
MAX. (uA)
MX29LV002NCTTC-70
MX29LV002NCBTC-70
MX29LV002NCTTC-90
MX29LV002NCBTC-90
MX29LV002NCTTI-70
MX29LV002NCBTI-70
MX29LV002NCTTI-90
MX29LV002NCBTI-90
MX29LV002NCTQC-70
MX29LV002NCBQC-70
MX29LV002NCTQC-90
MX29LV002NCBQC-90
MX29LV002NCTQI-70
MX29LV002NCBQI-70
MX29LV002NCTQI-90
MX29LV002NCBQI-90
MX29LV002NCTTC-70G
MX29LV002NCTTC-90G
MX29LV002NCBTC-70G
MX29LV002NCBTC-90G
MX29LV002NCTTI-70G
MX29LV002NCTTI-90G
MX29LV002NCBTI-70G
MX29LV002NCBTI-90G
MX29LV002NCTQC-70G
MX29LV002NCTQC-90G
MX29LV002NCBQC-70G
MX29LV002NCBQC-90G
MX29LV002NCTQI-70G
MX29LV002NCTQI-90G
MX29LV002NCBQI-70G
MX29LV002NCBQI-90G
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin TSOP
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
32 Pin PLCC
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
PB free
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
P/N:PM1204
REV. 1.0, JUN. 30, 2005
53
MX29LV002C/002NC T/B
PART NAME DESCRIPTION
MX 29 LV 002/002N C T T C 70 G
OPTION:
G: Lead-free package
R: Restricted VCC (3.0V~3.6V)
Q: Restricted VCC (3.0V~3.6V) with Lead-free package
SPEED:
70: 70ns
90: 90ns
TEMPERATURE RANGE:
C: Commercial (0˚C to 70˚C)
I: Industrial (-40˚C to 85˚C)
PACKAGE:
Q: PLCC
T: TSOP
BOOT BLOCK TYPE:
T: Top Boot
B: Bottom Boot
REVISION:
C
DENSITY & MODE:
002: 2M, x8 Boot Block
002N: 2M, x8 Boot Block, RESET PIN DISABLE
TYPE:
L, LV: 3V
DEVICE:
29:Flash
P/N:PM1204
REV. 1.0, JUN. 30, 2005
54
MX29LV002C/002NC T/B
PACKAGE INFORMATION
P/N:PM1204
REV. 1.0, JUN. 30, 2005
55
MX29LV002C/002NC T/B
P/N:PM1204
REV. 1.0, JUN. 30, 2005
56
MX29LV002C/002NC T/B
REVISION HISTORY
Revision No. Description
Page
P1
Date
JUN/30/2005
1.0
1. Removed "Preliminary"
2. Added "Recommended Operating Conditions"
P48
P/N:PM1204
REV. 1.0, JUN. 30, 2005
57
MX29LV002C/002NC T/B
MACRONIX INTERNATIONALCO., LTD.
Headquarters:
TEL:+886-3-578-6688
FAX:+886-3-563-2888
Europe Office :
TEL:+32-2-456-8020
FAX:+32-2-456-8021
Hong Kong Office :
TEL:+86-755-834-335-79
FAX:+86-755-834-380-78
Japan Office :
Kawasaki Office :
TEL:+81-44-246-9100
FAX:+81-44-246-9105
Osaka Office :
TEL:+81-6-4807-5460
FAX:+81-6-4807-5461
Singapore Office :
TEL:+65-6346-5505
FAX:+65-6348-8096
Taipei Office :
TEL:+886-2-2509-3300
FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-262-8887
FAX:+1-408-262-8810
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
相关型号:
©2020 ICPDF网 联系我们和版权申明