74AUP1Z04GW [NEXPERIA]
Low-power X-tal driver with enable and internal resistorProduction;
| 型号： | 74AUP1Z04GW |
| 厂家： | 
Nexperia |
| 描述： | Low-power X-tal driver with enable and internal resistorProduction 驱动 光电二极管 逻辑集成电路 |
| 文件： | 总25页 (文件大小：333K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Rev. 8 — 17 July 2023
Product data sheet
1. General description
The 74AUP1Z04 is a crystal driver with enable and internal resistor. When not in use the EN input
can be driven HIGH, putting the device in a low power disable mode with X1 pulled HIGH via RPU
X2 set LOW and Y set HIGH. Schmitt trigger action on the EN input makes the circuit tolerant to
slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V.
,
2. Features and benefits
•
Wide supply voltage range from 0.8 V to 3.6 V
•
•
•
•
•
•
•
CMOS low power dissipation
High noise immunity
Overvoltage tolerant inputs to 3.6 V
Low noise overshoot and undershoot < 10 % of VCC
IOFF circuitry provides partial Power-down mode operation at output Y
Latch-up performance exceeds 100 mA per JESD78B Class II
Complies with JEDEC standards:
•
•
•
•
•
JESD8-12 (0.8 V to 1.3 V)
JESD8-11 (0.9 V to 1.65 V)
JESD8-7 (1.65 V to 1.95 V)
JESD8-5 (2.3 V to 2.7 V)
JESD8C (2.7 V to 3.6 V)
•
ESD protection:
•
•
HBM: ANSI/ESDA/JEDEC JS-001 class 3A exceeds 5000 V
CDM: ANSI/ESDA/JEDEC JS-002 class C3 exceeds 1000 V
•
•
Multiple package options
Specified from -40 °C to +85 °C and -40 °C to +125 °C
3. Ordering information
Table 1. Ordering information
Type number
Package
Temperature range Name
Description
Version
74AUP1Z04GW
74AUP1Z04GM
74AUP1Z04GN
74AUP1Z04GS
-40 °C to +125 °C
-40 °C to +125 °C
-40 °C to +125 °C
-40 °C to +125 °C
TSSOP6
plastic thin shrink small outline package; 6 leads;
body width 1.25 mm
SOT363-2
XSON6
XSON6
XSON6
plastic extremely thin small outline package;
no leads; 6 terminals; body 1 × 1.45 × 0.5 mm
SOT886
SOT1115
SOT1202
extremely thin small outline package; no leads;
6 terminals; body 0.9 × 1.0 × 0.35 mm
extremely thin small outline package; no leads;
6 terminals; body 1.0 × 1.0 × 0.35 mm
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
4. Marking
Table 2. Marking
Type number
Marking code[1]
74AUP1Z04GW
74AUP1Z04GM
74AUP1Z04GN
74AUP1Z04GS
a4
a4
a4
a4
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
5. Functional diagram
V
CC
R
PU
3
1
6
4
X1
Y
R
bias
X2
EN
001aae488
RPU= pull-up resistance.
Rbias= bias resistance.
Fig. 1. Logic symbol
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
2 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
6. Pinning information
6.1. Pinning
GM package
SOT886 (XSON6)
GW package
SOT363-2 (TSSOP6)
EN
GND
X1
1
2
3
6
5
Y
V
1
2
3
6
5
4
EN
GND
X1
Y
V
CC
CC
4
X2
X2
aaa-035924
aaa-035923
Transparent top view
GN package
GS package
SOT1115 (XSON6)
SOT1202 (XSON6)
EN
1
2
3
6
5
4
Y
V
EN
GND
X1
1
2
3
6
5
4
Y
V
GND
X1
CC
CC
X2
X2
aaa-035925
Transparent top view
aaa-035926
Transparent top view
6.2. Pin description
Table 3. Pin description
Symbol
Pin
1
Description
EN
GND
X1
enable input (active LOW)
ground (0 V)
2
3
data input
X2
4
data output
VCC
Y
5
supply voltage
data output
6
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
3 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
7. Functional description
Table 4. Function table
H = HIGH voltage level; L = LOW voltage level.
Input
Output
EN
L
X1
L
X2
H
L
Y
L
L
H
L
H
L
H
H
H
L
H
H
8. Limiting values
Table 5. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
-0.5
-50
-0.5
-50
-0.5
-
Max
+4.6
-
Unit
V
VCC
IIK
supply voltage
input clamping current
input voltage
VI < 0 V
mA
V
VI
[1]
[1]
+4.6
-
IOK
VO
IO
output clamping current
output voltage
VO < 0 V
mA
VCC + 0.5 V
output current
VO = 0 V to VCC
±20
50
mA
ICC
IGND
Tstg
Ptot
supply current
-
mA
mA
°C
ground current
-50
-65
-
-
storage temperature
total power dissipation
+150
250
Tamb = -40 °C to +125 °C
[2]
mW
[1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For SOT363-2 (TSSOP6) package: Ptot derates linearly with 3.7 mW/K above 83 °C.
For SOT886 (XSON6) package: Ptot derates linearly with 3.3 mW/K above 74 °C.
For SOT1115 (XSON6) package: Ptot derates linearly with 3.2 mW/K above 71 °C.
For SOT1202 (XSON6) package: Ptot derates linearly with 3.3 mW/K above 74 °C.
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
4 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
9. Recommended operating conditions
Table 6. Recommended operating conditions
Symbol Parameter
Conditions
Min
0.8
0
Max
3.6
Unit
V
VCC
VI
supply voltage
input voltage
3.6
V
VO
output voltage
0
VCC
+125
200
V
Tamb
Δt/ΔV
ambient temperature
input transition rise and fall rate
-40
-
°C
ns/V
VCC = 0.8 V to 3.6 V
10. Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Tamb = 25 °C
Conditions
Min
Typ
Max
Unit
VIH
HIGH-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
VCC = 0.8 V
0.75 × VCC
-
-
V
0.70 × VCC
0.65 × VCC
1.6
-
-
-
-
-
-
-
-
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.0
VIL
LOW-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
-
-
0.25 × VCC
V
VCC = 0.8 V
-
-
-
-
-
-
-
-
0.30 × VCC
0.35 × VCC
0.7
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
5 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VOH
HIGH-level output
voltage
Y output; VI at X1 input = VIH or VIL
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
Y output; VI at X1 input = VIH or VIL
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VCC - 0.1
0.75 × VCC
1.11
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.32
2.05
1.9
2.72
2.6
VCC - 0.1
0.75 × VCC
1.11
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.32
2.05
1.9
2.72
2.6
VOL
LOW-level output
voltage
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.31
V
V
V
V
V
V
V
V
0.31
0.31
0.44
0.31
0.44
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.31
V
V
V
V
V
V
V
V
0.31
0.31
0.44
0.31
0.44
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
6 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
±0.1
±0.1
Unit
μA
II
input leakage current
X1 input
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
μA
Ipu
pull-up current
X1 input; EN = VCC
VI = GND; VCC = 0.8 V to 3.6 V
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
15
μA
μA
IOFF
ΔIOFF
ICC
power-off leakage
current
[1]
±0.2
additional power-off
leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V [1]
-
-
-
-
±0.2
75
μA
μA
supply current
VI = GND or VCC; IO = 0 A; EN = GND;
VCC = 0.8 V to 3.6 V
ΔICC
additional supply current EN input
VI = VCC - 0.6 V; IO = 0 A; VCC = 3.3 V
X1 input
VCC = 0 V to 3.6 V; VI = GND or VCC
EN input
VCC = 0 V to 3.6 V; VI = GND or VCC
X2 output
VO = GND; VCC = 0 V
Y output
-
-
-
-
-
-
40
-
μA
pF
pF
pF
pF
CI
input capacitance
output capacitance
1.3
0.8
1.5
1.7
-
CO
-
VO = GND; VCC = 0 V
see Fig. 7 and Fig. 8
VCC = 0.8 V
-
gfs
forward
transconductance
-
-
-
mA/V
mA/V
mA/V
mA/V
mA/V
mA/V
MΩ
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.2
3.9
7.9
18
-
9.9
-
17.7
24.3
30.7
32.4
3.08
-
-
-
20.5
1.08
Rbias
bias resistance
EN = GND; fi = 0 Hz; VI = 0 V or VCC
see Fig. 2; for frequency behavior
see Fig. 3
;
1.62
Tamb = -40 °C to +85 °C
VIH
HIGH-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
0.75 × VCC
-
-
V
VCC = 0.8 V
0.70 × VCC
0.65 × VCC
1.6
-
-
-
-
-
-
-
-
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.0
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
7 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VIL
LOW-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
VCC = 0.8 V
-
-
0.25 × VCC
V
-
-
-
-
-
-
-
-
0.30 × VCC
0.35 × VCC
0.7
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
VOH
HIGH-level output
voltage
Y output; VI at X1 input = VIH or VIL
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
VI at X1 input = VIH or VIL
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
Y output; VI at X1 input = VIH or VIL
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VCC - 0.1
0.7 × VCC
1.03
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.30
1.97
1.85
2.67
2.55
VCC - 0.1
0.7 × VCC
1.03
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.30
1.97
1.85
2.67
2.55
VOL
LOW-level output
voltage
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.37
V
V
V
V
V
V
V
V
0.35
0.33
0.45
0.33
0.45
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.37
V
V
V
V
V
V
V
V
0.35
0.33
0.45
0.33
0.45
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
8 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
±0.5
±0.5
Unit
μA
II
input leakage current
X1 input
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
μA
Ipu
pull-up current
X1 input; EN = VCC
VI = GND; VCC = 0.8 V to 3.6 V
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
15
μA
μA
IOFF
ΔIOFF
ICC
power-off leakage
current
[1]
[1]
±0.5
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
-
-
-
-
±0.6
75
μA
μA
supply current
VI = GND or VCC; IO = 0 A; EN = GND;
VCC = 0.8 V to 3.6 V
ΔICC
additional supply current EN input
VI = VCC - 0.6 V; IO = 0 A; VCC = 3.3 V
-
-
50
μA
gfs
forward
transconductance
see Fig. 7 and Fig. 8
VCC = 0.8 V
-
-
-
-
-
-
-
-
-
mA/V
mA/V
mA/V
mA/V
mA/V
mA/V
MΩ
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
-
10.8
21.2
29.9
38.0
39.2
3.11
1.8
7.5
15.0
17.8
1.07
Rbias
bias resistance
EN = GND; fi = 0 Hz; VI = 0 V or VCC
see Fig. 2; for frequency behavior
see Fig. 3
;
Tamb = -40 °C to +125 °C
VIH HIGH-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
0.75 × VCC
-
-
V
VCC = 0.8 V
0.75 × VCC
0.70 × VCC
1.6
-
-
-
-
-
-
-
-
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.0
VIL
LOW-level input voltage X1 input
VCC = 0.8 V to 3.6 V
EN input
-
-
0.25 × VCC
V
VCC = 0.8 V
-
-
-
-
-
-
-
-
0.25 × VCC
0.30 × VCC
0.7
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
9 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
Unit
V
VOH
HIGH-level output
Y output; VI at X1 input = VIH or VIL
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
Y output; VI at X1 input = VIH or VIL
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
voltage
VCC - 0.11
0.6 × VCC
0.93
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
1.17
V
1.77
V
1.67
V
2.40
V
2.30
V
V
VCC - 0.11
0.6 × VCC
0.93
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
1.17
V
1.77
V
1.67
V
2.40
V
2.30
V
VOL
LOW-level output
voltage
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.11
0.33 × VCC
0.41
V
V
V
V
V
V
V
V
0.39
0.36
0.50
0.36
0.50
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.11
0.33 × VCC
0.41
V
V
V
V
V
V
V
V
0.39
0.36
0.50
0.36
0.50
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
10 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter
Conditions
Min
Typ
Max
±0.75
±0.75
Unit
μA
II
input leakage current
X1 input
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
μA
Ipu
pull-up current
X1 input; EN = VCC
VI = GND; VCC = 0.8 V to 3.6 V
VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
15
μA
μA
IOFF
ΔIOFF
ICC
power-off leakage
current
[1]
[1]
±0.75
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
-
-
-
-
±0.75
75
μA
μA
supply current
VI = GND or VCC; IO = 0 A; EN = GND;
VCC = 0.8 V to 3.6 V
ΔICC
additional supply current EN input
VI = VCC - 0.6 V; IO = 0 A; VCC = 3.3 V
-
-
75
μA
gfs
forward
transconductance
see Fig. 7 and Fig. 8
VCC = 0.8 V
-
-
-
-
-
-
-
-
-
mA/V
mA/V
mA/V
mA/V
mA/V
mA/V
MΩ
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
-
10.8
21.2
29.9
38.0
39.2
3.11
1.8
6.9
13.4
15.8
1.07
Rbias
bias resistance
EN = GND; fi = 0 Hz; VI = 0 V or VCC
see Fig. 2; for frequency behavior
see Fig. 3
;
[1] Only for output Y and input EN.
R
bias
V
CC
X
X
2
1
I
I
V
V
I
O
001aai359
Fig. 2. Test circuit for measuring bias resistance
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
11 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
001aai159
20
bias
R
(MΩ)
16
(1)
12
8
(2)
(3)
4
0
1.0
1.5
2.0
2.5
3.0
V
3.5
(V)
CC
(1) fi = 30 kHz.
(2) fi = 1 MHz.
(3) fi = 10 MHz.
Fig. 3. Typical bias resistance versus supply voltage
11. Dynamic characteristics
Table 8. Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 6.
Symbol Parameter Conditions
Tamb = 25 °C
Tamb = -40 °C
to +85 °C
Tamb = -40 °C Unit
to +125 °C
Min Typ [1] Max
Min
Max
Min
Max
CL = 5 pF
tpd
propagation X1 to X2; see Fig. 4
[2]
delay
VCC = 0.8 V
-
12.8
3.0
2.2
1.9
1.6
1.4
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 5
VCC = 0.8 V
1.2
1.0
0.8
0.7
0.7
3.9
2.6
2.3
1.9
1.6
1.2
1.0
0.8
0.7
0.7
3.9
2.7
2.4
2.0
1.7
1.2
1.0
0.8
0.7
0.7
3.9 ns
2.7 ns
2.5 ns
2.0 ns
1.7 ns
[2]
-
39.2
8.0
5.5
4.4
3.5
3.1
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.5
2.2
1.8
1.5
1.5
10.7
6.6
5.5
4.1
3.5
2.3
2.0
1.7
1.4
1.4
10.8
7.0
5.9
4.4
3.8
2.3
2.0
1.7
1.4
1.4
10.9 ns
7.0 ns
6.0 ns
4.5 ns
3.8 ns
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
12 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter Conditions
Tamb = 25 °C
Tamb = -40 °C
to +85 °C
Tamb = -40 °C Unit
to +125 °C
Min Typ [1] Max
Min
Max
Min
Max
CL = 10 pF
tpd
propagation X1 to X2; see Fig. 4
[2]
delay
VCC = 0.8 V
-
20.9
4.1
2.9
2.5
2.0
1.8
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 5
VCC = 0.8 V
1.4
1.3
1.2
0.9
0.9
5.4
3.6
3.0
2.4
2.1
1.3
1.2
1.1
0.8
0.8
5.6
3.8
3.2
2.5
2.3
1.3
1.2
1.1
0.8
0.8
5.6 ns
3.8 ns
3.2 ns
2.5 ns
2.3 ns
[2]
-
46.6
9.2
6.3
5.0
4.0
3.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.7
2.5
2.3
1.8
1.9
12.4
7.8
6.2
4.7
4.2
2.5
2.2
2.2
1.7
1.8
12.7
8.2
6.7
5.0
4.5
2.5
2.2
2.2
1.7
1.8
12.7 ns
8.2 ns
6.7 ns
5.1 ns
4.5 ns
CL = 15 pF
tpd
propagation X1 to X2; see Fig. 4
[2]
delay
VCC = 0.8 V
-
28.9
5.2
3.6
3.0
2.4
2.2
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 5
VCC = 0.8 V
1.7
1.6
1.3
1.0
1.1
7.1
4.4
3.7
2.9
2.5
1.6
1.6
1.3
1.0
1.0
7.2
4.7
3.9
3.1
2.7
1.6
1.6
1.3
1.0
1.0
7.3 ns
4.8 ns
4.0 ns
3.1 ns
2.7 ns
[2]
-
53.9
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
3.1
2.9
2.5
2.1
2.3
10.4 14.2
2.8
2.7
2.3
2.0
2.1
14.6
9.2
7.4
5.7
5.1
2.8
2.7
2.3
2.0
2.1
14.7 ns
9.3 ns
7.5 ns
5.7 ns
5.1 ns
7.0
5.6
4.5
4.1
8.5
6.9
5.4
4.7
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
13 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Symbol Parameter Conditions
Tamb = 25 °C
Tamb = -40 °C
to +85 °C
Tamb = -40 °C Unit
to +125 °C
Min Typ [1] Max
Min
Max
Min
Max
CL = 30 pF
tpd
propagation X1 to X2; see Fig. 4
[2]
delay
VCC = 0.8 V
-
52.8
8.5
5.6
4.5
3.7
3.3
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 5
VCC = 0.8 V
2.4
2.2
2.0
1.5
1.7
11.8
6.8
5.6
4.2
3.7
2.3
2.0
1.9
1.4
1.6
12.2
7.5
6.2
4.6
4.0
2.3
2.0
1.9
1.4
1.6
12.4 ns
7.6 ns
6.2 ns
4.6 ns
4.2 ns
[2]
-
77.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
3.7
3.4
3.4
2.6
3.2
13.8 19.2
3.3
3.1
3.1
2.4
2.9
19.8
12.2
9.7
3.3
3.1
3.1
2.4
2.9
20.1 ns
12.3 ns
9.7 ns
7.4 ns
6.9 ns
9.2
7.4
5.9
5.4
11.2
8.8
6.7
7.4
6.2
6.7
CL = 5 pF, 10 pF, 15 pF and 30 pF
CPD power fi = 1 MHz; EN = GND;
[3][4][5]
dissipation VI = GND to VCC
capacitance
VCC = 0.8 V
-
-
-
-
-
-
6.8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
pF
pF
pF
VCC = 1.1 V to 1.3 V
12.0
18.2
19.2
21.9
24.9
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
[1] All typical values are measured at nominal VCC
.
[2] tpd is the same as tPLH and tPHL
.
[3] All specified values are the average typical values over all stated loads.
[4] CPD is used to determine the dynamic power dissipation (PD in μW).
PD = CPD × VCC 2 × fi × N + Σ(CL × VCC 2 × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
Σ(CL × VCC 2 × fo) = sum of the outputs.
[5] Feedback current is included in the CPD
.
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
14 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
11.1. Waveforms and test circuit
V
I
V
X1 input
M
GND
t
t
PLH
PHL
V
OH
V
X2 output
M
V
OL
mnb099
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig. 4. The input (X1) to output (X2) propagation delays
V
I
V
X1 input
Y output
M
GND
t
t
PLH
PHL
V
OH
V
M
V
OL
mnb100
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig. 5. The input (X1) to output (Y) propagation delays
Table 9. Measurement points
Supply voltage
VCC
Output
VM
Input
VM
VI
tr = tf
0.8 V to 3.6 V
0.5 × VCC
0.5 × VCC
VCC
≤ 3.0 ns
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
15 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
V
V
EXT
CC
5 kΩ
V
I
V
O
G
DUT
R
T
C
L
R
L
001aac521
Test data is given in Table 10.
Definitions for test circuit:
RL = Load resistance;
CL = Load capacitance including jig and probe capacitance;
RT = Termination resistance should be equal to the output impedance Zoof the pulse generator;
VEXT = External voltage for measuring switching times.
Fig. 6. Test circuit for measuring switching times
Table 10. Test data
Supply voltage
VCC
Load
CL
VEXT
RL [1]
tPLH, tPHL
open
tPZH, tPHZ
tPZL, tPLZ
0.8 V to 3.6 V
5 pF, 10 pF, 15 pF and 30 pF 5 kΩ or 1 MΩ
GND
2 × VCC
[1] For measuring enable and disable times RL = 5 kΩ.
For measuring propagation delays, setup and hold times and pulse width RL = 1 MΩ.
001aad074
30
g
fs
(mA/V)
R
bias
20
V
CC
0.47 µF
100 µF
X
X
2
1
10
V
I
o
i
001aai360
0
0
1
2
3
4
V
(V)
CC
fi = 1 kHz.
VO is constant.
Tamb = 25°C.
Fig. 7. Test set-up for measuring forward
transconductance
Fig. 8. Typical forward transconductance as a function
of supply voltage
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
16 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
12. Application information
Crystal controlled oscillator circuits are widely used in clock pulse generators because of their
excellent frequency stability and wide operating frequency range. The use of the 74AUP1Z04
provides the additional advantages of low power dissipation, stable operation over a wide range of
frequency and temperature and a very small footprint. This application information describes crystal
characteristics, design and testing of crystal oscillator circuits based on the 74AUP1Z04.
12.1. Crystal characteristics
Fig. 9 is the equivalent circuit of a quartz crystal.
The reactive and resistive component of the impedance of the crystal alone and the crystal with a
series and a parallel capacitance is shown in Fig. 10.
C
X1
=
C
X0
L
X1
R
X1
001aai361
Fig. 9. Equivalent circuit of a crystal
+
resistance
reactance
C
X1
R
1
0
C
X0
L
X1
(1)
f
f
a
r
f
R
X1
+
0
resistance
reactance
C
R
L
X1
C
X0
L
X1
(2)
f
f
a
L
f
R
X1
C
L
+
0
R
p
C
resistance
reactance
X1
C
L
C
X0
L
X1
(3)
f
f
f
a
r
L
f
R
X1
001aai362
(1) resonance
(2) anti-resonance
(3) load resonance
Fig. 10. Reactance and resistance characteristics of a crystal
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
17 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
12.1.1. Design
Fig. 11 shows the recommended way to connect a crystal to the 74AUP1Z04. This circuit is
basically a Pierce oscillator circuit in which the crystal is operating at its fundamental frequency
and is tuned by the parallel load capacitance of C1 and C2. C1 and C2 are in series with the crystal.
They should be approximately equal. R1 is the drive-limiting resistor and is set to approximately the
same value as the reactance of C1 at the crystal frequency (R1 = XC1). This will result in an input to
the crystal of 50 % of the rail-to-rail output of X2. This keeps the drive level into the crystal within
drive specifications (the designer should verify this). Overdriving the crystal can cause damage.
The internal bias resistor provides negative feedback and sets a bias point of the inverter near
mid-supply, operating the 74AUP1GU04 portion in the high gain linear region.
To calculate the values of C1 and C2, the designer can use the formula:
CL is the load capacitance as specified by the crystal manufacturer, Cs is the stray capacitance of
the circuit (for the 74AUP1Z04 this is equal to an input capacitance of 1.5 pF).
74AUP1GU04
portion
74AUP1G04
portion
system
load
R
bias
Y
X1
X2
R
1
C
sys
R
sys
Xtal
C
2
C
1
001aai363
Fig. 11. Crystal oscillator configuration for the 74AUP1Z04
12.1.2. Testing
After the calculations are performed for a particular crystal, the oscillator circuit should be tested.
The following simple checks will verify the prototype design of a crystal controlled oscillator circuit.
Perform them after laying out the board:
•
Test the oscillator over worst-case conditions (lowest supply voltage, worst-case crystal and
highest operating temperature). Adding series and parallel resistors can simulate a worst-case
crystal.
•
•
Insure that the circuit does not oscillate without the crystal.
Check the frequency stability over a supply range greater than that which is likely to occur
during normal operation.
•
Check that the start-up time is within system requirements.
As the 74AUP1Z04 isolates the system loading, once the design is optimized, the single layout
may work in multiple applications for any given crystal.
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
18 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
13. Package outline
TSSOP6: plastic thin shrink small outline package; 6 leads; body width 1.25 mm
SOT363-2
D
B
E
A
X
c
(6x)
y
H
E
v
M
A
e
1
6
5
4
pin 1 index
A
A
2
A
1
1
2
3
A
3
θ
L
w
M B
p
b
p
(6x)
detail X
e
e
0
3 mm
scale
Dimensions (mm are the original dimensions)
Unit
(1)
(1)
A
A
A
A
b
c
D
E
e
e
1
H
E
L
p
v
w
y
θ
1
2
3
p
max 1.1 0.1 1.0
0.8 0.8
0.30 0.25 2.2 1.35
0.15 0.08 1.8 1.15
2.4 0.46
1.8 0.26
8°
0°
mm
0.15
0.65 1.3
0.3 0.1 0.1
0
min
Note
1. Plastic or metal protrusions of 0.2 mm maximum per side are not included.
sot363-2_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
21-12-15
21-12-16
SOT363-2
SC-88A
MO-203
Fig. 12. Package outline SOT363-2 (TSSOP6)
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
19 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm
SOT886
b
1
2
3
4x
(2)
L
L
1
e
6
5
4
e
e
1
1
6x
(2)
A
A
1
D
E
terminal 1
index area
0
1
2 mm
scale
Dimensions (mm are the original dimensions)
(1)
Unit
A
A
b
D
E
e
e
L
L
1
1
1
max 0.5 0.04 0.25 1.50 1.05
0.35 0.40
0.30 0.35
0.27 0.32
nom
min
0.20 1.45 1.00 0.6
0.17 1.40 0.95
mm
0.5
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
sot886_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
MO-252
JEITA
04-07-22
12-01-05
SOT886
Fig. 13. Package outline SOT886 (XSON6)
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
20 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
XSON6: extremely thin small outline package; no leads;
6 terminals; body 0.9 x 1.0 x 0.35 mm
SOT1115
b
3
(2)
(4×)
1
2
L
L
1
e
6
5
4
e
e
1
1
(2)
(6×)
A
1
A
D
E
terminal 1
index area
0
L
0.5
scale
1 mm
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
1
1
max 0.35 0.04 0.20 0.95 1.05
0.35 0.40
0.15 0.90 1.00 0.55 0.3 0.30 0.35
0.12 0.85 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1115_po
Issue date
References
Outline
version
European
projection
IEC
JEDEC
JEITA
10-04-02
10-04-07
SOT1115
Fig. 14. Package outline SOT1115 (XSON6)
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
21 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
XSON6: extremely thin small outline package; no leads;
6 terminals; body 1.0 x 1.0 x 0.35 mm
SOT1202
b
(2)
1
2
3
(4×)
L
L
1
e
6
5
4
e
e
1
1
(2)
(6×)
A
1
A
D
E
terminal 1
index area
0
L
0.5
1 mm
scale
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
1
1
max 0.35 0.04 0.20 1.05 1.05
0.35 0.40
0.15 1.00 1.00 0.55 0.35 0.30 0.35
0.12 0.95 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1202_po
Issue date
References
Outline
version
European
projection
IEC
JEDEC
JEITA
10-04-02
10-04-06
SOT1202
Fig. 15. Package outline SOT1202 (XSON6)
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
22 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
14. Abbreviations
Table 11. Abbreviations
Acronym
Description
CDM
DUT
ESD
HBM
Charged Device Model
Device Under Test
ElectroStatic Discharge
Human Body Model
15. Revision history
Table 12. Revision history
Document ID
Release date Data sheet status
20230717 Product data sheet
Section 1 updated.
Section 2: ESD specification updated according to the latest JEDEC standard.
Product data sheet 74AUP1Z04 v.6
SOT363 (SC-88) package changed to SOT363-2 (TSSOP6) package.
20200717 Product data sheet 74AUP1Z04 v.5
Change notice Supersedes
74AUP1Z04 v.8
Modifications:
- 74AUP1Z04 v.7
•
•
74AUP1Z04 v.7
Modifications:
20220127
-
•
74AUP1Z04 v.6
Modifications:
-
•
The format of this data sheet has been redesigned to comply with the identity
guidelines of Nexperia.
•
•
•
•
Legal texts have been adapted to the new company name where appropriate.
Type number 74AUP1Z04GF (SOT891) removed.
Section 1 and Section 2 updated.
Table 5: Derating values for Ptot total power dissipation updated.
74AUP1Z04 v.5
Modifications:
20120809
Product data sheet
-
74AUP1Z04 v.4
•
Package outline drawing of SOT886 (Fig. 13) modified.
74AUP1Z04 v.4
Modifications:
20111201
Product data sheet
-
74AUP1Z04 v.3
•
Legal pages updated.
74AUP1Z04 v.3
74AUP1Z04 v.2
74AUP1Z04 v.1
20100722
20080703
20061212
Product data sheet
Product data sheet
Product data sheet
-
-
-
74AUP1Z04 v.2
74AUP1Z04 v.1
-
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
23 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
injury, death or severe property or environmental damage. Nexperia and its
suppliers accept no liability for inclusion and/or use of Nexperia products in
such equipment or applications and therefore such inclusion and/or use is at
the customer’s own risk.
16. Legal information
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Data sheet status
Document status Product
Definition
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Nexperia makes no representation
or warranty that such applications will be suitable for the specified use
without further testing or modification.
[1][2]
status [3]
Objective [short]
data sheet
Development
This document contains data from
the objective specification for
product development.
Customers are responsible for the design and operation of their applications
and products using Nexperia products, and Nexperia accepts no liability for
any assistance with applications or customer product design. It is customer’s
sole responsibility to determine whether the Nexperia product is suitable
and fit for the customer’s applications and products planned, as well as
for the planned application and use of customer’s third party customer(s).
Customers should provide appropriate design and operating safeguards to
minimize the risks associated with their applications and products.
Preliminary [short]
data sheet
Qualification
Production
This document contains data from
the preliminary specification.
Product [short]
data sheet
This document contains the product
specification.
[1] Please consult the most recently issued document before initiating or
completing a design.
Nexperia does not accept any liability related to any default, damage, costs
or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party
customer(s). Customer is responsible for doing all necessary testing for the
customer’s applications and products using Nexperia products in order to
avoid a default of the applications and the products or of the application or
use by customer’s third party customer(s). Nexperia does not accept any
liability in this respect.
[2] The term 'short data sheet' is explained in section "Definitions".
[3] The product status of device(s) described in this document may have
changed since this document was published and may differ in case of
multiple devices. The latest product status information is available on
the internet at https://www.nexperia.com.
Definitions
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those
given in the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Nexperia does not give any representations or
warranties as to the accuracy or completeness of information included herein
and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is
intended for quick reference only and should not be relied upon to contain
detailed and full information. For detailed and full information see the relevant
full data sheet, which is available on request via the local Nexperia sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of commercial sale — Nexperia products are
sold subject to the general terms and conditions of commercial sale, as
published at http://www.nexperia.com/profile/terms, unless otherwise agreed
in a valid written individual agreement. In case an individual agreement is
concluded only the terms and conditions of the respective agreement shall
apply. Nexperia hereby expressly objects to applying the customer’s general
terms and conditions with regard to the purchase of Nexperia products by
customer.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
Nexperia and its customer, unless Nexperia and customer have explicitly
agreed otherwise in writing. In no event however, shall an agreement be
valid in which the Nexperia product is deemed to offer functions and qualities
beyond those described in the Product data sheet.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Disclaimers
Limited warranty and liability — Information in this document is believed
to be accurate and reliable. However, Nexperia does not give any
representations or warranties, expressed or implied, as to the accuracy
or completeness of such information and shall have no liability for the
consequences of use of such information. Nexperia takes no responsibility
for the content in this document if provided by an information source outside
of Nexperia.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific Nexperia product is automotive qualified, the
product is not suitable for automotive use. It is neither qualified nor tested in
accordance with automotive testing or application requirements. Nexperia
accepts no liability for inclusion and/or use of non-automotive qualified
products in automotive equipment or applications.
In no event shall Nexperia be liable for any indirect, incidental, punitive,
special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards,
customer (a) shall use the product without Nexperia’s warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
Nexperia’s specifications such use shall be solely at customer’s own risk,
and (c) customer fully indemnifies Nexperia for any liability, damages or failed
product claims resulting from customer design and use of the product for
automotive applications beyond Nexperia’s standard warranty and Nexperia’s
product specifications.
Notwithstanding any damages that customer might incur for any reason
whatsoever, Nexperia’s aggregate and cumulative liability towards customer
for the products described herein shall be limited in accordance with the
Terms and conditions of commercial sale of Nexperia.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Right to make changes — Nexperia reserves the right to make changes
to information published in this document, including without limitation
specifications and product descriptions, at any time and without notice. This
document supersedes and replaces all information supplied prior to the
publication hereof.
Trademarks
Suitability for use — Nexperia products are not designed, authorized or
warranted to be suitable for use in life support, life-critical or safety-critical
systems or equipment, nor in applications where failure or malfunction
of an Nexperia product can reasonably be expected to result in personal
Notice: All referenced brands, product names, service names and
trademarks are the property of their respective owners.
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
24 / 25
Nexperia
74AUP1Z04
Low-power X-tal driver with enable and internal resistor
Contents
1. General description......................................................1
2. Features and benefits.................................................. 1
3. Ordering information....................................................1
4. Marking..........................................................................2
5. Functional diagram.......................................................2
6. Pinning information......................................................3
6.1. Pinning.........................................................................3
6.2. Pin description.............................................................3
7. Functional description................................................. 4
8. Limiting values............................................................. 4
9. Recommended operating conditions..........................5
10. Static characteristics..................................................5
11. Dynamic characteristics...........................................12
11.1. Waveforms and test circuit.......................................15
12. Application information........................................... 17
12.1. Crystal characteristics..............................................17
12.1.1. Design...................................................................18
12.1.2. Testing.................................................................. 18
13. Package outline........................................................ 19
14. Abbreviations............................................................23
15. Revision history........................................................23
16. Legal information......................................................24
© Nexperia B.V. 2023. All rights reserved
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release: 17 July 2023
©
74AUP1Z04
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2023. All rights reserved
Product data sheet
Rev. 8 — 17 July 2023
25 / 25
相关型号：
74AUP1Z125GN
AUP/ULP/V SERIES, 1-BIT DRIVER, TRUE OUTPUT, PDSO6, 0.90 X 1 MM, 0.35 MM HEIGHT, SOT-1115, SON-6
NXP
74AUP1Z125GN,132
74AUP1Z125 - Low-power X-tal driver with enable and internal resistor; 3-state SON 6-Pin
NXP
©2020 ICPDF网 联系我们和版权申明