74AUP1Z125GS [NEXPERIA]
Low-power X-tal driver with enable and internal resistor; 3-stateProduction;型号: | 74AUP1Z125GS |
厂家: | Nexperia |
描述: | Low-power X-tal driver with enable and internal resistor; 3-stateProduction 驱动 光电二极管 逻辑集成电路 |
文件: | 总23页 (文件大小:326K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
74AUP1Z125
Low-power X-tal driver with enable and internal resistor;
3-state
Rev. 7 — 28 January 2022
Product data sheet
1. General description
The 74AUP1Z125 is a crystal driver with enable, internal resistor and 3-state output. When not
in use the EN input can be driven HIGH, putting the device in a low power disable mode with X1
pulled HIGH via RPU, X2 set LOW and Y in the high impedance OFF-state. In disable mode the
output Y assumes the high impedance OFF-state. Schmitt trigger action on the EN input makes the
circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V.
Schmitt-trigger action at all inputs makes the circuit tolerant of slower input rise and fall times.
2. Features and benefits
•
Wide supply voltage range from 0.8 V to 3.6 V
•
•
•
CMOS low power dissipation
High noise immunity
Complies with JEDEC standards:
•
•
•
•
•
JESD8-12 (0.8 V to 1.3 V)
JESD8-11 (0.9 V to 1.65 V)
JESD8-7 (1.65 V to 1.95 V)
JESD8-5 (2.3 V to 2.7 V)
JESD8C (2.7 V to 3.6 V)
•
ESD protection:
•
•
•
HBM JESD22-A114F Class 3A exceeds 5000 V
MM JESD22-A115-A exceeds 200 V
CDM JESD22-C101E exceeds 1000 V
•
•
•
•
•
•
Latch-up performance exceeds 100 mA per JESD78B Class II Level B
Overvoltage tolerant inputs to 3.6 V
Low noise overshoot and undershoot < 10 % of VCC
IOFF circuitry provides partial Power-down mode operation at output Y
Multiple package options
Specified from -40 °C to +85 °C and -40 °C to +125 °C
3. Ordering information
Table 1. Ordering information
Type number
Package
Temperature range Name
Description
Version
74AUP1Z125GW
74AUP1Z125GM
74AUP1Z125GN
74AUP1Z125GS
-40 °C to +125 °C
-40 °C to +125 °C
-40 °C to +125 °C
-40 °C to +125 °C
TSSOP6
plastic thin shrink small outline package; 6 leads;
body width 1.25 mm
SOT363-2
XSON6
XSON6
XSON6
plastic extremely thin small outline package; no leads; SOT886
6 terminals; body 1 × 1.45 × 0.5 mm
extremely thin small outline package; no leads;
6 terminals; body 0.9 × 1.0 × 0.35 mm
SOT1115
extremely thin small outline package; no leads;
6 terminals; body 1.0 × 1.0 × 0.35 mm
SOT1202
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
4. Marking
Table 2. Marking
Type number
Marking code [1]
74AUP1Z125GW
74AUP1Z125GM
74AUP1Z125GN
74AUP1Z125GS
55
55
55
55
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
5. Functional diagram
V
CC
R
PU
3
1
6
4
X1
Y
R
bias
X2
EN
001aaf141
RPU = pull-up resistance.
Rbias = bias resistance.
Fig. 1. Logic symbol
6. Pinning information
6.1. Pinning
74AUP1Z125
74AUP1Z125
EN
GND
X1
1
2
3
6
5
4
Y
74AUP1Z125
1
2
3
6
5
4
EN
GND
X1
Y
V
EN
GND
X1
1
2
3
6
5
4
Y
V
V
CC
CC
CC
X2
X2
X2
001aaf143
Transparent top view
001aaf144
Transparent top view
001aaf142
Fig. 2. Pin configuration SOT363-2 Fig. 3. Pin configuration SOT886
(TSSOP6) (XSON6)
Fig. 4. Pin configuration SOT1115
and SOT1202 (XSON6)
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
2 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
6.2. Pin description
Table 3. Pin description
Symbol
Pin
1
Description
EN
GND
X1
enable input (active LOW)
ground (0 V)
2
3
data input
X2
4
unbuffered output
supply voltage
data output
VCC
Y
5
6
7. Functional description
Table 4. Function table
H = HIGH voltage level; L = LOW voltage level; Z = high-impedance OFF-state.
Input
EN
L
Output
X1
L
X2
H
L
Y
H
L
L
H
L
H
H
L
Z
Z
H
H
8. Limiting values
Table 5. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
-0.5
-50
-0.5
-50
-0.5
-
Max
+4.6
-
Unit
V
VCC
IIK
supply voltage
input clamping current
input voltage
VI < 0 V
mA
V
VI
[1]
[1]
+4.6
-
IOK
VO
IO
output clamping current
output voltage
VO < 0 V
mA
V
Active mode and Power-down mode
VO = 0 V to VCC
+4.6
±20
50
output current
mA
mA
mA
°C
ICC
IGND
Tstg
Ptot
supply current
-
ground current
-50
-65
-
-
storage temperature
total power dissipation
+150
250
Tamb = -40 °C to +125 °C
[2]
mW
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For SOT363-2 (TSSOP6) package: Ptot derates linearly with 3.7 mW/K above 83 °C.
For SOT886 (XSON6) package: Ptot derates linearly with 3.3 mW/K above 74 °C.
For SOT1115 (XSON6) package: Ptot derates linearly with 3.2 mW/K above 71 °C.
For SOT1202 (XSON6) package: Ptot derates linearly with 3.3 mW/K above 74 °C.
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
3 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
9. Recommended operating conditions
Table 6. Recommended operating conditions
Symbol Parameter
Conditions
Min
0.8
0
Max
3.6
Unit
V
VCC
VI
supply voltage
input voltage
3.6
V
VO
output voltage
0
VCC
+125
200
V
Tamb
Δt/ΔV
ambient temperature
input transition rise and fall rate
-40
-
°C
ns/V
VCC = 0.8 V to 3.6 V
10. Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Tamb = 25 °C
Typ
Tamb = -40 °C to +85 °C
Tamb = -40 °C to +125 °C Unit
Min
Max
Min
Max
Min
Max
VIH
HIGH-level input
voltage
X1 input; VCC = 0.8 V to 3.6 V
EN input
0.75 × VCC
-
-
0.75 × VCC
-
0.75 × VCC
-
V
VCC = 0.8 V
0.70 × VCC
-
-
-
-
-
-
0.70 × VCC
-
0.75 × VCC
-
V
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.65 × VCC
-
0.65 × VCC
-
0.70 × VCC
-
1.6
2.0
-
-
1.6
2.0
-
-
1.6
2.0
-
-
-
-
-
VIL
LOW-level input voltage X1 input; VCC = 0.8 V to 3.6 V
0.25 × VCC
0.25 × VCC
0.25 × VCC
EN input
VCC = 0.8 V
-
-
-
-
-
-
-
-
0.3 × 0VCC
0.35 × VCC
0.7
-
-
-
-
0.30 × VCC
0.35 × VCC
0.7
-
-
-
-
0.25 × VCC
0.30 × VCC
0.7
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
0.9
0.9
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
4 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter
Conditions
Tamb = 25 °C
Typ
Tamb = -40 °C to +85 °C
Tamb = -40 °C to +125 °C Unit
Min
Max
Min
Max
Min
Max
VOH
HIGH-level output
voltage
Y output; VI at X1 input = VIH or VIL
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
X2 output; VI = GND or VCC
IO = -20 μA; VCC = 0.8 V to 3.6 V
IO = -1.1 mA; VCC = 1.1 V
IO = -1.7 mA; VCC = 1.4 V
IO = -1.9 mA; VCC = 1.65 V
IO = -2.3 mA; VCC = 2.3 V
IO = -3.1 mA; VCC = 2.3 V
IO = -2.7 mA; VCC = 3.0 V
IO = -4.0 mA; VCC = 3.0 V
VCC - 0.1
-
-
-
-
-
-
-
-
-
VCC - 0.1
0.7 × VCC
1.03
-
-
-
-
-
-
-
-
VCC - 0.11
0.6V × CC
0.93
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
0.75 × VCC
1.11
-
-
-
-
-
-
-
1.32
1.30
1.17
2.05
1.97
1.77
1.9
1.85
1.67
2.72
2.67
2.40
2.6
2.55
2.30
VCC - 0.1
0.75 × VCC
1.11
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
VCC - 0.1
0.7 × VCC
1.03
-
-
-
-
-
-
-
-
VCC - 0.11
0.6 × VCC
0.93
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.32
1.30
1.17
2.05
1.97
1.77
1.9
1.85
1.67
2.72
2.67
2.40
2.6
2.55
2.30
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
5 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter
Conditions
Tamb = 25 °C
Typ
Tamb = -40 °C to +85 °C
Tamb = -40 °C to +125 °C Unit
Min
Max
Min
Max
Min
Max
VOL
LOW-level output
voltage
Y output; VI at X1 input = VIH or VIL
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.31
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.37
-
-
-
-
-
-
-
-
0.11
0.33 × VCC
0.41
V
V
V
V
V
V
V
V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
0.31
0.35
0.39
0.31
0.33
0.36
IO = 3.1 mA; VCC = 2.3 V
0.44
0.45
0.50
IO = 2.7 mA; VCC = 3.0 V
0.31
0.33
0.36
IO = 4.0 mA; VCC = 3.0 V
0.44
0.45
0.50
X2 output; VI = GND or VCC
IO = 20 μA; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.31
-
-
-
-
-
-
-
-
-
-
-
0.1
0.3 × VCC
0.37
-
-
-
-
-
-
-
-
-
-
-
0.11
0.33 × VCC
0.41
V
V
IO = 1.7 mA; VCC = 1.4 V
V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
0.31
0.35
0.39
V
0.31
0.33
0.36
V
IO = 3.1 mA; VCC = 2.3 V
0.44
0.45
0.50
V
IO = 2.7 mA; VCC = 3.0 V
0.31
0.33
0.36
V
IO = 4.0 mA; VCC = 3.0 V
0.44
0.45
0.50
V
II
input leakage current
pull-up current
X1 input; VI = EN = VCC; VCC = 0 V to 3.6 V
EN input; VI = GND to 3.6 V; VCC = 0 V to 3.6 V
±0.1
±0.5
±0.75
±0.75
15
μA
μA
μA
±0.1
±0.5
Ipu
X1 input; EN = VCC; VI = GND;
VCC = 0.8 V to 3.6 V
15
15
IOZ
OFF-state output
current
Y output; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V;
EN = VCC
-
-
-
-
-
-
±0.1
±0.2
±0.2
-
-
-
±0.5
±0.5
±0.6
-
-
-
±0.75
±0.75
±0.75
μA
μA
μA
IOFF
ΔIOFF
power-off leakage
current
Only for output Y and input EN.
VI or VO = 0 V to 3.6 V; VCC = 0 V
additional power-off
leakage current
Only for output Y and input EN.
VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
6 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter
Conditions
Tamb = 25 °C
Tamb = -40 °C to +85 °C
Tamb = -40 °C to +125 °C Unit
Min
Typ
Max
75
Min
Max
75
Min
Max
75
ICC
supply current
VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V
-
-
-
-
-
-
-
-
μA
μA
ΔICC
additional supply
current
EN input; VI = VCC - 0.6 V; IO = 0 A;
VCC = 3.3 V
40
50
75
CI
input capacitance
X1 input; VCC = 0 V to 3.6 V; VI = GND or VCC
EN input; VCC = 0 V to 3.6 V; VI = GND or VCC
X2 output; VO = GND; VCC = 0 V
Y output; VO = GND; VCC = 0 V
see Fig. 5 and Fig. 6
-
-
-
-
1.3
0.8
1.5
1.7
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
pF
CO
gfs
output capacitance
forward
transconductance
VCC = 0.8 V
-
-
-
-
-
-
-
mA/V
mA/V
mA/V
mA/V
mA/V
mA/V
MΩ
VCC = 1.1 V to 1.3 V
0.2
3.9
7.9
18
-
9.9
-
10.8
21.2
29.9
38.0
39.2
3.11
-
10.8
21.2
29.9
38.0
39.2
3.11
VCC = 1.4 V to 1.6 V
-
17.7
24.3
30.7
32.4
3.08
1.8
7.5
15.0
17.8
1.07
1.8
6.9
13.4
15.8
1.07
VCC = 1.65 V to 1.95 V
-
VCC = 2.3 V to 2.7 V
-
-
VCC = 3.0 V to 3.6 V
20.5
1.08
Rbias
bias resistance
EN = GND; fi = 0 Hz; VI = 0 V or VCC
;
1.62
see Fig. 7; for frequency behavior see Fig. 8
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
7 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
11. Test circuits and graphs
001aad074
30
g
fs
(mA/V)
R
bias
V
CC
20
0.47 µF
100 µF
X
X
2
1
V
I
o
i
10
001aai360
0
0
1
2
3
4
V
(V)
CC
fi = 1 kHz.
VO is constant.
Tamb = 25 °C.
Fig. 5. Test set-up for measuring forward
transconductance
Fig. 6. Typical forward transconductance as a function
of supply voltage
001aai159
20
R
bias
(MΩ)
16
(1)
12
8
R
bias
V
CC
(2)
(3)
4
X
X
2
1
I
I
0
1.0
V
1.5
2.0
2.5
3.0
V
3.5
(V)
V
O
I
CC
001aai359
(1) fi = 30 kHz.
(2) fi = 1 MHz
(3) fi = 10 MHz
Fig. 7. Test circuit for measuring bias resistance
Fig. 8. Typical bias resistance versus supply voltage
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
8 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
12. Dynamic characteristics
Table 8. Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 11.
Symbol Parameter Conditions
CL = 5 pF
25 °C
-40 °C to +85 °C -40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
Min
Max
tpd
propagation X1 to X2; see Fig. 9
[2]
[2]
[2]
[2]
delay
VCC = 0.8 V
-
6.2
2.3
1.7
1.4
1.1
1.0
-
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 9
0.9
0.7
0.5
0.4
0.3
4.4
3.1
2.6
2.0
1.8
0.9
0.6
0.5
0.4
0.3
4.8
3.4
2.9
2.3
2.1
0.9
0.6
0.5
0.4
0.3
5.3
3.8
3.2
2.6
2.4
VCC = 0.8 V
-
18.5
5.9
4.2
3.5
2.9
2.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
enable time EN to Y; see Fig. 10
VCC = 0.8 V
2.8
2.2
1.9
1.6
1.4
12.5
7.7
6.2
4.8
4.1
3.2
2.6
2.2
1.9
1.7
14.8
9.1
7.8
6.2
4.7
3.2
2.6
2.2
1.9
1.7
16.3 ns
10.1 ns
8.6
6.9
5.2
ns
ns
ns
ten
-
31.2
6.1
4.3
3.6
2.9
2.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
disable time EN to Y; see Fig. 10
VCC = 0.8 V
3.1
2.5
2.1
1.8
1.7
13.8
8.2
6.5
4.8
4.1
2.9
2.3
2.0
1.7
1.7
16.3
9.7
7.6
5.8
4.7
2.9
2.3
2.0
1.7
1.7
18.0 ns
10.7 ns
8.4
6.4
5.2
ns
ns
ns
tdis
-
11.1
4.5
3.3
3.2
2.3
2.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.5
2.0
1.9
1.4
1.7
9.0
6.4
6.0
4.4
4.4
2.9
2.3
2.0
1.7
1.7
9.4
6.7
6.4
4.7
4.9
2.9
2.3
2.0
1.7
1.7
10.4 ns
7.4
7.1
5.2
5.4
ns
ns
ns
ns
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
9 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter Conditions
CL = 10 pF
25 °C
-40 °C to +85 °C -40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
Min
Max
tpd
propagation X1 to X2; see Fig. 9
[2]
[2]
[2]
[2]
delay
VCC = 0.8 V
-
9.6
3.1
2.3
1.9
1.5
1.3
-
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 9
1.2
1.0
0.8
0.6
0.5
6.1
4.0
3.3
2.7
2.4
1.2
0.9
0.7
0.6
0.5
6.8
4.6
3.8
3.1
2.7
1.2
0.9
0.7
0.6
0.5
7.5
5.1
4.2
3.5
3.0
VCC = 0.8 V
-
21.4
6.7
4.9
4.1
3.4
3.1
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
enable time EN to Y; see Fig. 10
VCC = 0.8 V
3.2
2.1
1.9
2.1
1.8
14.3
8.9
6.9
5.4
4.8
3.6
3.0
2.6
2.3
2.1
16.2
10.1
8.0
3.6
3.0
2.6
2.3
2.1
17.9 ns
11.2 ns
8.8
7.3
6.2
ns
ns
ns
6.6
5.6
ten
-
34.4
6.9
5.0
4.2
3.4
3.2
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
disable time EN to Y; see Fig. 10
VCC = 0.8 V
3.6
2.3
2.0
1.8
1.7
15.5
9.3
7.2
5.5
4.9
3.4
2.2
1.9
1.7
1.7
16.0
9.6
7.9
6.4
5.5
3.4
2.2
1.9
1.7
1.7
17.6 ns
10.6 ns
8.7
7.1
6.1
ns
ns
ns
tdis
-
13.0
5.7
4.2
4.3
3.1
3.8
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
3.4
2.1
2.2
1.6
2.1
10.4
7.6
7.3
5.3
6.0
3.4
2.2
1.9
1.7
1.7
10.8
8.0
7.6
5.5
6.5
3.4
2.2
1.9
1.7
1.7
11.9 ns
8.8
8.4
6.1
7.2
ns
ns
ns
ns
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
10 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter Conditions
CL = 15 pF
25 °C
-40 °C to +85 °C -40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
Min
Max
tpd
propagation X1 to X2; see Fig. 9
[2]
[2]
[2]
[2]
delay
VCC = 0.8 V
-
13.0
3.8
2.8
2.3
1.9
1.6
-
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 9
1.6
1.3
1.0
0.8
0.7
7.9
4.9
4.0
3.2
2.9
1.4
1.1
0.9
0.8
0.7
8.8
5.7
4.7
3.7
3.3
1.4
1.1
0.9
0.8
0.7
9.7
6.3
5.2
4.1
3.7
VCC = 0.8 V
-
24.2
7.5
5.4
4.6
3.9
3.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
enable time EN to Y; see Fig. 10
VCC = 0.8 V
3.6
3.0
2.2
2.0
2.0
16.1
9.7
7.7
6.1
5.4
4.0
3.3
2.9
2.6
2.3
17.6
10.6
9.0
4.0
3.3
2.9
2.6
2.3
19.4 ns
11.7 ns
9.9
8.1
6.5
ns
ns
ns
7.3
5.9
ten
-
37.5
7.7
5.5
4.7
3.9
3.6
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
disable time EN to Y; see Fig. 10
VCC = 0.8 V
4.0
3.0
2.3
2.0
2.0
17.2
10.0
7.9
3.7
2.5
2.1
2.0
1.9
17.5
10.2
9.2
3.7
2.5
2.1
2.0
1.9
19.3 ns
11.3 ns
10.2 ns
6.2
7.4
8.2
6.6
ns
ns
5.5
6.0
tdis
-
14.8
6.8
5.1
5.4
3.9
5.1
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
4.3
3.0
3.0
2.1
2.9
11.2
8.1
8.0
6.1
7.2
3.7
2.5
2.1
2.0
1.9
12.4
8.9
9.3
7.3
7.9
3.7
2.5
2.1
2.0
1.9
13.7 ns
9.8 ns
10.3 ns
8.1
8.7
ns
ns
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
11 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Symbol Parameter Conditions
CL = 30 pF
25 °C
-40 °C to +85 °C -40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
Min
Max
tpd
propagation X1 to X2; see Fig. 9
[2]
[2]
[2]
[2]
delay
VCC = 0.8 V
-
23.2
6.0
4.2
3.6
2.9
2.5
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Fig. 9
2.4
2.0
1.7
1.4
1.2
13.1
7.6
6.1
4.8
4.3
2.2
1.8
1.5
1.3
1.1
14.8
9.0
7.2
5.7
5.1
2.2
1.8
1.5
1.3
1.1
16.3 ns
9.9
8.0
6.3
5.7
ns
ns
ns
ns
VCC = 0.8 V
-
32.6
9.6
6.9
5.9
5.0
4.7
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
enable time EN to Y; see Fig. 10
VCC = 0.8 V
4.8
4.0
2.9
2.7
2.7
21.0
12.4
9.8
5.0
4.3
3.8
3.3
3.1
21.7
13.5
10.7
8.2
5.0
4.3
3.8
3.3
3.1
23.9 ns
14.9 ns
11.8 ns
7.5
9.1
8.5
ns
ns
6.8
7.7
ten
-
47.1
9.9
7.1
6.0
5.0
4.8
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
disable time EN to Y; see Fig. 10
VCC = 0.8 V
5.2
4.0
3.0
2.7
2.7
21.0
12.4
9.9
4.8
3.1
2.8
2.6
2.6
21.7
13.5
10.7
8.1
4.8
3.1
2.8
2.6
2.6
23.9 ns
14.9 ns
11.8 ns
7.7
9.0
8.5
ns
ns
6.8
7.7
tdis
-
20.3
-
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
6.0
4.4
5.1
3.6
5.2
10.2 15.3
4.8
3.1
2.8
2.6
2.6
16.5
12.3
13.3
9.5
4.8
3.1
2.8
2.6
2.6
18.2 ns
13.6 ns
14.7 ns
10.5 ns
14.3 ns
7.8
8.8
6.3
8.8
11.2
12.5
8.6
11.5
13.0
CL = 5 pF, 10 pF, 15 pF and 30 pF
CPD
power
dissipation
capacitance
fi = 1 MHz; EN = GND;
VI = GND to VCC
[3][4]
VCC = 0.8 V
-
-
-
-
-
-
7.1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
pF
pF
pF
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
12.9
19.2
19.9
21.6
24.3
[1] All typical values are measured at nominal VCC
.
[2] tpd is the same as tPLH and tPHL; ten is the same as tPZH and tPZL; tdis is the same as tPHZ and tPLZ
.
[3] CPD is used to determine the dynamic power dissipation (PD in μW). PD = CPD × VCC 2 × fi × N + Σ(CL × VCC 2 × fo) where:
fi = input frequency in MHz; fo = output frequency in MHz;
CL = output load capacitance in pF; VCC = supply voltage in V;
N = number of inputs switching; Σ(CL × VCC 2 × fo) = sum of the outputs.
[4] Feedback current is included in CPD
.
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
12 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
12.1. Waveforms and test circuit
V
I
X1 input
GND
V
V
M
M
t
t
PHL
PLH
V
OH
X2, Y output
V
V
M
M
V
OL
001aaf145
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig. 9. The input (X1) to output (X2, Y) propagation delays
Table 9. Measurement points
Supply voltage
VCC
Output
VM
Input
VM
VI
tr = tf
0.8 V to 3.6 V
0.5 × VCC
0.5 × VCC
VCC
≤ 3.0 ns
V
I
V
EN input
M
GND
t
t
PLZ
PZL
V
CC
Y output
LOW-to-OFF
OFF-to-LOW
V
M
V
V
OL
X
t
t
PHZ
PZH
V
OH
V
Y
Y output
V
HIGH-to-OFF
OFF-to-HIGH
M
GND
outputs
enabled
outputs
enabled
outputs
disabled
001aaf146
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig. 10. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
Output
VM
VM
VX
VY
0.8 V to 1.6 V
1.65 V to 2.7 V
3.0 V to 3.6 V
0.5 × VCC
0.5 × VCC
0.5 × VCC
0.5 × VCC
0.5 × VCC
0.5 × VCC
VOL + 0.1 V
VOL + 0.15 V
VOL + 0.3 V
VOH - 0.1 V
VOH - 0.15 V
VOH - 0.3 V
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
13 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
V
V
EXT
CC
5 kΩ
V
I
V
O
G
DUT
R
T
C
L
R
L
001aac521
Test data is given in Table 11.
Definitions for test circuit:
RL = Load resistance;
CL = Load capacitance including jig and probe capacitance;
RT = Termination resistance should be equal to the output impedance Zo of the pulse generator;
VEXT = External voltage for measuring switching times.
Fig. 11. Test circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
Load
CL
VEXT
RL [1]
tPLH, tPHL
open
tPZH, tPHZ
tPZL, tPLZ
0.8 V to 3.6 V
5 pF, 10 pF, 15 pF and 30 pF 5 kΩ or 1 MΩ
GND
2 × VCC
[1] For measuring enable and disable times RL = 5 kΩ.
For measuring propagation delays, setup and hold times and pulse width RL = 1 MΩ.
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
14 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
13. Application information
Crystal controlled oscillator circuits are widely used in clock pulse generators because of their
excellent frequency stability and wide operating frequency range. The use of the 74AUP1Z125
provides the additional advantages of low power dissipation, stable operation over a wide range of
frequency and temperature and a very small footprint. This application information describes crystal
characteristics, design and testing of crystal oscillator circuits based on the 74AUP1Z125.
13.1. Crystal characteristics
Fig. 12 is the equivalent circuit of a quartz crystal.
The reactive and resistive components of the impedance of the crystal alone, and the crystal with a
series and a parallel capacitance, is shown in Fig. 13.
C
1
C
0
L
1
R
1
mnb102
Fig. 12. Equivalent circuit of a crystal
+
C
L
1
resistance
reactance
R
1
C
0
(1)
1
0
f
f
a
r
∞
R
1
f
-
+
C
1
resistance
reactance
R
L
(2)
C
0
L
1
0
f
L
f
a
∞
f
R
1
C
L
-
+
R
C
L
p
1
resistance
reactance
C
L
C
0
(3)
1
0
-
f
f
a
f
L
r
∞
f
R
1
mnb104
(1) = resonance
(2) = anti-resonance
(3) = load resonance
Fig. 13. Reactance and resistance characteristics of a crystal
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
15 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
13.1.1. Design
Fig. 14 shows the recommended way to connect a crystal to the 74AUP1Z125. This circuit is
basically a Pierce oscillator circuit in which the crystal is operating at its fundamental frequency
and tuned by the parallel load capacitance of C1 and C2. C1 and C2 are in series with the crystal.
They should be approximately equal. R1 is the drive-limiting resistor and is set to approximately the
same value as the reactance of C1 at the crystal frequency (R1 = XC1). This results in an input to
the crystal of 50 % of the rail-to-rail output of X2. This keeps the drive level into the crystal within
drive specifications (the designer should verify this). Overdriving the crystal can cause damage.
The internal bias resistor provides negative feedback and sets a bias point of the inverter near
mid-supply, operating the 74AUP1GU04 in the high gain linear region.
To calculate the values of C1 and C2, the designer can use the formula:
CL is the load capacitance as specified by the crystal manufacturer. Cs is the stray capacitance of
the circuit and for 74AUP1Z125, Cs is equal to an input capacitance of 1.5 pF.
74AUP1GU04 74AUP1G125
portion portion
system
load
R
bias
Y
X1
X2
R
1
Xtal
C
2
C
1
C
sys
R
sys
001aai549
Fig. 14. Crystal oscillator configuration
13.1.2. Testing
After the calculations are performed for a particular crystal, the oscillator circuit should be tested.
The following simple checks verify the prototype design of a crystal controlled oscillator circuit.
Perform the checks after laying out the board:
•
Test the oscillator over worst-case conditions (lowest supply voltage, worst-case crystal and
highest operating temperature). Adding series and parallel resistors can simulate a worse case
crystal.
•
•
Ensure that the circuit does not oscillate without the crystal.
Check the frequency stability over a supply range greater than that which is likely to occur
during normal operation.
•
Check that the start-up time is within system requirements.
As the 74AUP1Z125 isolates the system loading, once the design is optimized, the single layout
may work in multiple applications for any given crystal.
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
16 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
14. Package outline
TSSOP6: plastic thin shrink small outline package; 6 leads; body width 1.25 mm
SOT363-2
D
B
E
A
X
c
(6x)
y
H
E
v
M
A
e
1
6
5
4
pin 1 index
A
A
2
A
1
1
2
3
A
3
θ
L
w
M B
p
b
p
(6x)
detail X
e
e
0
3 mm
scale
Dimensions (mm are the original dimensions)
Unit
(1)
(1)
A
A
A
A
b
c
D
E
e
e
1
H
E
L
p
v
w
y
θ
1
2
3
p
max 1.1 0.1 1.0
0.8 0.8
0.30 0.25 2.2 1.35
0.15 0.08 1.8 1.15
2.4 0.46
1.8 0.26
8°
0°
mm
0.15
0.65 1.3
0.3 0.1 0.1
0
min
Note
1. Plastic or metal protrusions of 0.2 mm maximum per side are not included.
sot363-2_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
21-12-15
21-12-16
SOT363-2
SC-88A
MO-203
Fig. 15. Package outline SOT363-2 (TSSOP6)
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
17 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm
SOT886
b
1
2
3
4x
(2)
L
L
1
e
6
5
4
e
e
1
1
6x
(2)
A
A
1
D
E
terminal 1
index area
0
1
2 mm
scale
Dimensions (mm are the original dimensions)
(1)
Unit
A
A
b
D
E
e
e
L
L
1
1
1
max 0.5 0.04 0.25 1.50 1.05
0.35 0.40
0.30 0.35
0.27 0.32
nom
min
0.20 1.45 1.00 0.6
0.17 1.40 0.95
mm
0.5
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
sot886_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
MO-252
JEITA
04-07-22
12-01-05
SOT886
Fig. 16. Package outline SOT886 (XSON6)
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
18 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
XSON6: extremely thin small outline package; no leads;
6 terminals; body 0.9 x 1.0 x 0.35 mm
SOT1115
b
3
(2)
(4×)
1
2
L
L
1
e
6
5
4
e
e
1
1
(2)
(6×)
A
1
A
D
E
terminal 1
index area
0
L
0.5
scale
1 mm
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
1
1
max 0.35 0.04 0.20 0.95 1.05
0.35 0.40
0.15 0.90 1.00 0.55 0.3 0.30 0.35
0.12 0.85 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1115_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
10-04-02
10-04-07
SOT1115
Fig. 17. Package outline SOT1115 (XSON6)
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
19 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
XSON6: extremely thin small outline package; no leads;
6 terminals; body 1.0 x 1.0 x 0.35 mm
SOT1202
b
3
(2)
1
2
(4×)
L
L
1
e
6
5
4
e
e
1
1
(2)
(6×)
A
1
A
D
E
terminal 1
index area
0
L
0.5
1 mm
scale
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
1
1
max 0.35 0.04 0.20 1.05 1.05
0.35 0.40
0.15 1.00 1.00 0.55 0.35 0.30 0.35
0.12 0.95 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1202_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
10-04-02
10-04-06
SOT1202
Fig. 18. Package outline SOT1202 (XSON6)
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
20 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
15. Abbreviations
Table 12. Abbreviations
Acronym
Description
CDM
DUT
ESD
HBM
MM
Charged Device Model
Device Under Test
ElectroStatic Discharge
Human Body Model
Machine Model
16. Revision history
Table 13. Revision history
Document ID
Release date Data sheet status
20220128 Product data sheet
Section 2 updated.
SOT363 (SC-88) package changed to SOT363-2 (TSSOP6).
Product data sheet 74AUP1Z125 v.5
Change notice Supersedes
74AUP1Z125 v.7
Modifications:
- 74AUP1Z125 v.6
•
•
74AUP1Z125 v.6
Modifications:
20201211
-
•
The format of this data sheet has been redesigned to comply with the identity
guidelines of Nexperia.
•
•
•
•
Legal texts have been adapted to the new company name where appropriate.
Type number 74AUP1Z125GF (SOT891 / XSON6) removed.
Section 1 updated.
Table 5: Derating values for Ptot total power dissipation updated.
74AUP1Z125 v.5
Modifications:
20120808
Product data sheet
-
74AUP1Z125 v.4
74AUP1Z125 v.3
•
Package outline drawing of SOT886 (Fig. 16) modified.
74AUP1Z125 v.4
Modifications:
20111201
Product data sheet
-
•
Legal pages updated.
74AUP1Z125 v.3
74AUP1Z125 v.2
74AUP1Z125 v.1
20100909
20080807
20060803
Product data sheet
Product data sheet
Product data sheet
-
-
-
74AUP1Z125 v.2
74AUP1Z125 v.1
-
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
21 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
injury, death or severe property or environmental damage. Nexperia and its
suppliers accept no liability for inclusion and/or use of Nexperia products in
such equipment or applications and therefore such inclusion and/or use is at
the customer’s own risk.
17. Legal information
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Data sheet status
Document status Product
Definition
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Nexperia makes no representation
or warranty that such applications will be suitable for the specified use
[1][2]
status [3]
Objective [short]
data sheet
Development
This document contains data from
the objective specification for
product development.
without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using Nexperia products, and Nexperia accepts no liability for
any assistance with applications or customer product design. It is customer’s
sole responsibility to determine whether the Nexperia product is suitable
and fit for the customer’s applications and products planned, as well as
for the planned application and use of customer’s third party customer(s).
Customers should provide appropriate design and operating safeguards to
minimize the risks associated with their applications and products.
Preliminary [short]
data sheet
Qualification
Production
This document contains data from
the preliminary specification.
Product [short]
data sheet
This document contains the product
specification.
[1] Please consult the most recently issued document before initiating or
completing a design.
Nexperia does not accept any liability related to any default, damage, costs
or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party
customer(s). Customer is responsible for doing all necessary testing for the
customer’s applications and products using Nexperia products in order to
avoid a default of the applications and the products or of the application or
use by customer’s third party customer(s). Nexperia does not accept any
liability in this respect.
[2] The term 'short data sheet' is explained in section "Definitions".
[3] The product status of device(s) described in this document may have
changed since this document was published and may differ in case of
multiple devices. The latest product status information is available on
the internet at https://www.nexperia.com.
Definitions
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those
given in the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Nexperia does not give any representations or
warranties as to the accuracy or completeness of information included herein
and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is
intended for quick reference only and should not be relied upon to contain
detailed and full information. For detailed and full information see the relevant
full data sheet, which is available on request via the local Nexperia sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of commercial sale — Nexperia products are
sold subject to the general terms and conditions of commercial sale, as
published at http://www.nexperia.com/profile/terms, unless otherwise agreed
in a valid written individual agreement. In case an individual agreement is
concluded only the terms and conditions of the respective agreement shall
apply. Nexperia hereby expressly objects to applying the customer’s general
terms and conditions with regard to the purchase of Nexperia products by
customer.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
Nexperia and its customer, unless Nexperia and customer have explicitly
agreed otherwise in writing. In no event however, shall an agreement be
valid in which the Nexperia product is deemed to offer functions and qualities
beyond those described in the Product data sheet.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Disclaimers
Limited warranty and liability — Information in this document is believed
to be accurate and reliable. However, Nexperia does not give any
representations or warranties, expressed or implied, as to the accuracy
or completeness of such information and shall have no liability for the
consequences of use of such information. Nexperia takes no responsibility
for the content in this document if provided by an information source outside
of Nexperia.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific Nexperia product is automotive qualified, the
product is not suitable for automotive use. It is neither qualified nor tested in
accordance with automotive testing or application requirements. Nexperia
accepts no liability for inclusion and/or use of non-automotive qualified
products in automotive equipment or applications.
In no event shall Nexperia be liable for any indirect, incidental, punitive,
special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards,
customer (a) shall use the product without Nexperia’s warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
Nexperia’s specifications such use shall be solely at customer’s own risk,
and (c) customer fully indemnifies Nexperia for any liability, damages or failed
product claims resulting from customer design and use of the product for
automotive applications beyond Nexperia’s standard warranty and Nexperia’s
product specifications.
Notwithstanding any damages that customer might incur for any reason
whatsoever, Nexperia’s aggregate and cumulative liability towards customer
for the products described herein shall be limited in accordance with the
Terms and conditions of commercial sale of Nexperia.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Right to make changes — Nexperia reserves the right to make changes
to information published in this document, including without limitation
specifications and product descriptions, at any time and without notice. This
document supersedes and replaces all information supplied prior to the
publication hereof.
Trademarks
Suitability for use — Nexperia products are not designed, authorized or
warranted to be suitable for use in life support, life-critical or safety-critical
systems or equipment, nor in applications where failure or malfunction
of an Nexperia product can reasonably be expected to result in personal
Notice: All referenced brands, product names, service names and
trademarks are the property of their respective owners.
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
22 / 23
Nexperia
74AUP1Z125
Low-power X-tal driver with enable and internal resistor; 3-state
Contents
1. General description......................................................1
2. Features and benefits.................................................. 1
3. Ordering information....................................................1
4. Marking..........................................................................2
5. Functional diagram.......................................................2
6. Pinning information......................................................2
6.1. Pinning.........................................................................2
6.2. Pin description.............................................................3
7. Functional description................................................. 3
8. Limiting values............................................................. 3
9. Recommended operating conditions..........................4
10. Static characteristics..................................................4
11. Test circuits and graphs............................................ 8
12. Dynamic characteristics............................................ 9
12.1. Waveforms and test circuit...................................... 13
13. Application information........................................... 15
13.1. Crystal characteristics..............................................15
13.1.1. Design...................................................................16
13.1.2. Testing.................................................................. 16
14. Package outline........................................................ 17
15. Abbreviations............................................................21
16. Revision history........................................................21
17. Legal information......................................................22
© Nexperia B.V. 2022. All rights reserved
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release: 28 January 2022
©
74AUP1Z125
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2022. All rights reserved
Product data sheet
Rev. 7 — 28 January 2022
23 / 23
相关型号:
74AUP1Z125GW-G
IC AUP/ULP/V SERIES, 1-BIT DRIVER, INVERTED OUTPUT, PDSO6, PLASTIC, ROHS COMPLIANT, SOT-363, SC-88, 6 PIN, Bus Driver/Transceiver
NXP
©2020 ICPDF网 联系我们和版权申明