M2112JCFW01-B [NKK]
General Specifications;
| 型号： | M2112JCFW01-B |
| 厂家： | 
NIHON KAIHEIKI INDUSTRY CO. LTD. |
| 描述： | General Specifications 开关 光电二极管 |
| 文件： | 总6页 (文件大小：644K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series M2100
LED Tipped Rockers & Paddles
General Specifications
Electrical Capacity (Resistive Load)
B
Power Level (silver):
Logic Level (gold):
6A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
50,000 operations minimum
Mechanical Life:
Electrical Life:
25,000 operations minimum
Nominal Operating Force:
On-to-On Position
3.19N
Off-to-On Position
Paddles
Rockers
20°
Single Pole
Double Pole
Single Pole
Double Pole
3.92N
7.06N
9.80N
4.41N
6.37N
13.73N
17.65N
Angle of Throw:
Materials & Finishes
Housing:
Stainless steel
Stainless steel
Silver alloy or silver alloy with gold plating
Silver with silver plating or copper or brass with gold plating
Phosphor bronze
Diallyl phthalate (UL94V-0)
Mounting Bracket:
Movable Contacts:
Stationary Contacts:
Lamp Contacts:
Base:
Switch Terminals:
Lamp Terminals:
Copper with silver or gold plating
Brass with silver or gold plating
Environmental Data
Operating Temp Range:
–10°C through +55°C (+14°F through +131°F) for rockers
–25°C through +70°C (–13°F through +158°F) for paddles
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Humidity:
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock:
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Soldering Time & Temp:
Wave Soldering (PC version): See Profile B in Supplement section.
Manual Soldering: See Profile B in Supplement section.
Note: Lever must be in center position while soldering.
Cleaning:
PC mountable device is not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards:
UL:
UL94V-0 base
File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” before dash in part number to order UL recognized switch.
Single pole rockers with synchronous circuits & single color LEDs & solder lug or PC
recognized at 6A @ 125V AC.
CSA:
File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before dash in part number to order CSA certified switch.
All single pole rockers with synchronous circuits & single color LEDs certified at 6A @ 125V AC.
B92
www.nkkswitches.com
3/13/17
LED Tipped Rockers & Paddles
Series M2100
TYPICAL SWITCH ORDERING EXAMPLE
M21 1 2 N C F W 01
B
Poles
LED Colors
Single Color
Red
Contact Materials
& Ratings
1
SPDT
DPDT
Silver; Rated
6A @ 125V AC
* 2
C
E
F
W
G
* Available only with Rockers
with Terminals 01, 02, 03
Yellow
Gold; Rated 0.4VA max
@ 28V AC/DC max
Green
Bicolor
CF
Red/Green
Circuits
2
3
ON
ON
NONE
OFF
ON
ON
LED Circuits &
Actuator Types
Terminals &
Mounting Types
Rocker
01 Solder Lug with Flat Frame
02 Quick Connect with Flat Frame
03 Straight PC with Flat Frame
13 Straight PC with Bracket Mount
R
Isolated
N
Synchronous
Optional Bezel
& Colors
Paddle
01 Solder Lug with Snap-in Frame
02 Quick Connect with Snap-in Frame
03 Straight PC with Snap-in Frame
13 Straight PC with Bracket Mount
P
J
Isolated
For Snap-in Frame
Synchronous
A
B
E
Black
White
Yellow
Green
Blue
IMPORTANT:
F
Switches are supplied without UL & CSA marking unless specified.
UL & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the
General Specifications page.
G
H
Gray
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
M2112NCFW01
Red/Green LED
Synchronous LED Circuit
in Rocker Actuator
SPDT
ON-NONE-ON
Switch Circuit
Silver Contacts with
6-Amp Rating
Solder Lug Terminals
www.nkkswitches.com
B93
Series M2100
LED Tipped Rockers & Paddles
POLES & CIRCUITS & LED ILLUMINATION
Toggle Position & Terminal Numbers
Schematics
Down
Center
Up
Model
Pole & Throw
SPDT
Notes: Terminal numbers are not actually on the switch.
LEDs require an external power source.
B
2
(COM)
M2112
Connected Power Terminals
ON
2-3
NONE
NONE
ON
2-1
Isolated
Single Color
LED
L(+)
L(-)
Isolated LEDs (see schematics)
Connected LED Terminals
ON
4-6
NONE
NONE
ON
4-6
3
1
4
6
2 (COM)
Synchronous Single Color LED
Connected LED Terminals
ON
4-6
NONE
NONE
OFF
OPEN
Isolated
Bicolor LED
Red
Green
(+) Red
Synchronous Bicolor LED
Connected LED Terminals
Red
5-6
NONE
NONE
Green
5-4
3
1
6 COM
4
(
) Green
2
(COM)
M2113
SPDT
ON
2-3
OFF
OPEN
ON
2-1
Synchronous
Single Color
LED
Connected Power Terminals
L(+)
L(-)
3
1
4
6
Isolated LEDs (see schematics)
Connected LED Terminals
ON
4-6
ON
4-6
ON
4-6
2
(COM)
Synchronous Single Color LED
Red
Green
ON
4-6
OFF
OPEN
ON
4-6
Synchronous
Bicolor LED
Connected LED Terminals
3
1
6
5 COM (+)
4
Synchronous Bicolor LED
Connected LED Terminals
Red
5-6
OFF
OPEN
Green
5-4
External Connection
M2122
Connected Power Terminals
DPDT
2
(COM)
1
5
ON
2-3 5-6
NONE
NONE
ON
2-1 5-4
Isolated
Single Color
LED
L(+)
7
L(-)
3
6
4
9
Isolated LEDs (see schematics)
Connected LED Terminals
ON
7-9
NONE
NONE
ON
7-9
2
(COM)
5
Isolated
Bicolor LED
Synchronous Single Color LED
Connected LED Terminals
ON
7-9
NONE
NONE
OFF
OPEN
Red
Green
(+) Red
7
( ) Green
Synchronous Bicolor LED
Connected LED Terminals
Red
8-9
NONE
NONE
Green
8-7
3
1
6
4
9 COM
Synchronous
Single Color
LED
2
(COM)
5
M2123
DPDT
ON
2-3 5-6
OFF
OPEN
ON
2-1 5-4
Connected Power Terminals
L(+)
7
L(-)
3
1
6
4
9
Isolated LEDs (see schematics)
Connected LED Terminals
ON
7-9
ON
7-9
ON
7-9
2
(COM)
5
Synchronous
Bicolor LED
Synchronous Single Color LED
Connected LED Terminals
ON
7-9
OFF
OPEN
ON
7-9
Red
Green
Synchronous Bicolor LED
Connected LED Terminals
Red
8-9
OFF
OPEN
Green
8-7
3
1
6
4
9
8 COM (+)
7
External Connection
LED COLORS & SPECIFICATIONS
Rockers
Paddles
The electrical specifications shown are determined at a
basic temperature of 25°C. LED circuit is isolated and
requires an external power source. If the source voltage
exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula
in Supplement Section. The LED is an integral part of the
switch and not available separately.
Single Color
Bicolor
Single Color
Bicolor
E
C
F
CF
E
F
CF
C
Bicolor LED is translucent white when unlit.
Units
mA
Red Yellow Green Red/Green Red Yellow Green Red/Green
Maximum Forward Current
Typical Forward Current
Forward Voltage
IFM
IF
30
20
2.2
4
30
20
2.1
4
30
20
2.2
4
25
20
25
20
30
20
25
20
2.2
5
30/25
20/20
mA
VF
1.7/2.0 2.25 2.1
–––
2.0/2.2
V
Maximum Reverse Voltage
Current Reduction Rate Above 25°C
Ambient Temperature Range
VRM
∆IF
5
5
–––
V
0.38 0.38 0.38 0.33/0.33 0.33 0.40 0.33
–10° ~ +55°C –25° ~ +50°C
0.43/0.38
–25° ~ +70°C
mA/°C
B94
www.nkkswitches.com
LED Tipped Rockers & Paddles
Series M2100
LED CIRCUIT, ROCKER, & MOUNTING TYPE COMBINATIONS
(16.8)
.661
(13.5)
.531
Maximum Panel Thickness
.126” (3.2mm)
(16.8)
.661
Rocker with
R
Isolated LED Circuit
(13.5)
.531
20°
20°
B
Rocker with
N
Synchronous LED Circuit
(12.0)
.472
(17.8)
.701
(12.0)
.472
(9.8)
.386
(9.8)
.386
Material: Polyamide
(23.8)
.937
(3.5)
.138
(3.5)
.138
(0.6)
.024
Finish: Matte
(2.6) Dia Typ
.102
Color: Black
Flat Frame combines with
Terminal codes 01, 02, & 03.
Bracket combines with
Terminal code 13.
(10.1)
.398
TYPICAL ROCKER SWITCH DIMENSIONS
Single Pole
Solder Lug
(2.4) Dia Typ
.094
(12.0)
.472
(0.6)
.024
(0.8) Typ
.031
(4.8)
.189
6
5
4
3
2
1
(23.8)
.937
(13.0)
.512
20°
(4.7) Typ
.185
(29.5)
1.161
(2.5) Dia
.098
(1.17) Typ
.046
(2.0) Typ
.079
(6.9)
(4.8)
.189
(12.7)
.500
(3.5)
.138
(6.35)
.250
.272
(9.3)
.366
(9.8)
.386
(20.3)
.799
Single color LED switch does not have terminal 5.
M2112NCFW01
Double Pole
Solder Lug
(6.35)
.250
(2.4) Dia Typ
.094
(12.0)
.472
(0.6)
.024
(0.8) Typ
.031
(4.8)
.189
9
8
7
6
3
(23.8)
.937
5
4
2
1
(13.0)
.512
20°
(4.7) Typ
.185
(29.5)
1.161
(2.5) Dia
.098
(2.0) Typ
.079
(4.8) Typ
.189
(1.17) Typ
.046
(6.9)
(3.5)
.138
(6.35)
.250
.272
(9.3)
.366
(17.5)
.689
(20.3)
.799
(9.8)
.386
Single color LED switch does not have terminal 8.
M2122NCFW01
Single Pole Only
Straight PC • Bracket
(9.0)
.354
(12.0)
.472
(4.5)
.177
(3.2) Typ
.126
6
3
2
1
(0.8) Typ
.031
(17.8)
.701
5
4
(13.0)
.512
20°
(15.8)
(4.7) Typ
.185
.622
(2.5) Dia
.098
(1.17) Typ
.046
(1.17) Typ
.046
(0.5) Typ
.020
(10.1)
.398
(6.35)
.250
(3.5)
.138
(4.8)
.189
(12.7)
.500
(9.8)
.386
(20.3)
.799
(9.3)
.366
Single color LED switch does not have terminal 5. Silver contact material is standard.
M2112NCFW13
www.nkkswitches.com
B95
Series M2100
LED Tipped Rockers & Paddles
LED CIRCUIT, PADDLE, & MOUNTING TYPE COMBINATIONS
P
J
Paddle with Isolated LED Circuit
Maximum Panel Thickness
.039” ~ .126” (1.0 ~ 3.2mm)
without Bezel
.039” ~ .098” (1.0 ~ 2.5mm)
with Bezel
B
Maximum
Panel
Thickness
Paddle with Synchronous LED Circuit
.126” (3.2mm)
20°
20°
(3.2)
.126
(3.2)
.126
(4.5)
(4.5)
.177
.177
(15.9)
.626
(12.7)
.500
Material: Polyamide
Finish: Matte
(13.7)
.539
(5.9) R
.232
(5.9) R
(20.1)
.232
.791
(0.5)
.020
Color: Black
(13.1)
.516
(12.4)
.490
(7.1)
.280
(2.8)
.110
(3.5)
.138
Snap-in combines with Terminal codes 01, 02, & 03
Bracket combines with Terminal code 13
TYPICAL PADDLE SWITCH DIMENSIONS
Solder Lug • Snap-in
Single Pole Only
(4.8)
.189
(0.5)
.020
(0.8) Typ
.031
6
5
4
3
2
1
(18.0)
.709
(13.0)
.512
20°
(4.7) Typ
.185
(2.0)
.079
(3.2)
.126
(1.17) Typ
.046
(2.0) Typ
.079
(2.8)
.110
(5.0)
.197
(7.1)
.280
(6.35)
.250
(4.8)
.189
(12.7)
.500
(11.5)
.453
(12.2)
.480
(13.7)
.539
(26.5)
1.043
M2112JCFW01
Single color LED switch does not have terminal 5.
Straight PC • Bracket
Single Pole Only
(9.0)
.354
(4.5)
.177
(3.2) Typ
.126
6
3
2
1
(0.8) Typ
.031
5
4
(13.0)
.512
20°
(15.8)
(4.7) Typ
.185
.622
(2.0)
.079
(3.2)
.126
(5.0)
(1.17) Typ
.046
(1.17) Typ
.046
(0.5) Typ
.020
.197
(4.8)
.189
(6.35)
.250
(9.0)
(3.5)
.138
.354
(11.5)
(12.7)
.500
(20.1)
.791
(20.2)
.795
.453
M2112JCFW13
Silver contact material is standard. Single color LED switch does not have terminal 5.
B96
www.nkkswitches.com
LED Tipped Rockers & Paddles
Series M2100
CONTACT MATERIALS & RATINGS
W
G
Silver over Silver
Power Level
Logic Level
6A @ 125V AC & 3A @ 250V AC
B
Gold over Brass or Copper
0.4VA maximum @ 28V AC/DC maximum
Complete explanation of operating range in Supplement section.
TERMINALS
Solder Lug with
(2.0)
01
03
02
Epoxy Seal
.079
Turret LED Terminal
Quick Connect
(4.0)
.157
(6.35)
.250
(6.35)
.250
(4.8)
.189
(4.8)
.189
Epoxy Seal
(2.0)
.079
(1.1)
(1.57) Typ
.062
(1.17)
.046
(4.8)
.189
.043
(4.8)
.189
Thk = (0.8) Typ
.031
Thk = (0.8) Typ
.031
Straight PC with
Turret LED Terminal
Single Pole
Double Pole
(4.8)
.189
(4.8) Typ
.189
Single color LED
& isolated bicolor
LED switches do not
have terminal 5.
Single color LED
& isolated bicolor
LED switches do not
have terminal 8.
3
2
1
3
2
1
6
5
4
9
8
7
6
5
4
(6.35)
.250
(4.7) Typ
.185
(4.7) Typ
.185
(4.8)
.189
Epoxy Seal
(1.17) Typ
.046
(4.8)
.189
(1.8) Dia Typ
.073
(1.8) Dia Typ
.073
Thk = (0.8) Typ
.031
Single Pole
Straight PC with Bracket
& Turret LED Terminal
13
(1.6) Typ
.063
(2.4) Typ
.095
3
2
1
6
5
4
Single color LED
& isolated bicolor
LED switches do not
have terminal 5.
(7.9) Typ
.311
(4.7) Typ
.185
(1.8) Dia Typ
.073
(1.5) Dia Typ
.059
C
L
OPTIONAL BEZEL & COLORS
AT2107 Bezel for Snap-in Panel Frame
Material: Polyamide
(11.8)
.465
(15.9)
.626
(2.2)
.087
Finish: Matte
(12.0)
.472
(15.6)
.614
(13.1)
.516
(21.5)
.846
A
B
E
F
G
H
Colors Available:
Black
White
Yellow
Green
Blue
Gray
www.nkkswitches.com
B97
相关型号：
©2020 ICPDF网 联系我们和版权申明