NP0115AG03LCF-CDG11S [NKK]
General Specifications;型号: | NP0115AG03LCF-CDG11S |
厂家: | NIHON KAIHEIKI INDUSTRY CO. LTD. |
描述: | General Specifications |
文件: | 总6页 (文件大小:220K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Series NP01
Subminiature Smooth Actuation Pushbuttons
General Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Other Ratings
Contact Resistance:
50 milliohms maximum
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
500 megohms minimum @ 250V DC
250V AC minimum between contacts for 1 minute minimum
500,000 operations minimum
500,000 operations minimum
Standard: 1.5N 0.5 Newtons
High: 2.5N 0.8 Newtons
D
Electrical Life:
Nominal Operating Force:
Stroke:
1.5mm (.059”)
Materials & Finishes
Actuator:
Case:
Silicon rubber
Polycarbonate resin
Base:
Glass fiber reinforced polyamide resin
Silver over nickel with gold plating
Brass with gold plating
Movable Contact:
Stationary Contacts:
Switch Terminals:
Brass with gold plating
Environmental Data
Operating Temperature Range:
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Humidity:
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
2
Shock:
50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Cap Installation Force:
5.0N maximum downward force on actuator
PCB Processing
Soldering:
Cleaning:
Wave Soldering: 270°C maximum @ 6 seconds maximum
Manual Soldering: 390°C maximum @ 4 seconds maximum
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
D74
www.nkkswitches.com
7/19/17
Subminiature Smooth Actuation Pushbuttons
Series NP01
Distinctive Characteristics
Soft touch actuation achieved by mechanical silicon rubber structure.
Distinct, long stroke of 1.5mm (.059”).
Entire cap is fully illuminated with single or bicolor LED.
D
Compact design with dimension of 12.5mm (.492”) from
PC board to top of cap.
Alternating legend options with bicolor LED.
Available in both high (2.5N) or standard (1.5N)
operating force.
Gold plated contacts provide high reliability.
Crimped terminals ensure secure PC mounting
and prevent dislodging during soldering.
Molded-in terminals prevent entry of flux, solvents,
and other contaminants.
Actual Size
www.nkkswitches.com
D75
Series NP01
Subminiature Smooth Actuation Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
NP01 15 H G03 L F JF
Pole & Circuit
SPST OFF (ON)
( ) = Momentary
Contacts & Terminals
Illumination
Packaging
15
Gold Contacts and
G03 PC Terminals, Rated
0.4VA @ 28V AC/DC
Illuminated
L
Partitioned Tray,
Any Quantity
No
Nonilluminated
N
Normally Open Contacts
Code (With or without
caps installed)
D
Stick-Tube
50 Pieces/Stick
S
(For switch body
only; caps pack-
aged separately)
Operating Force
LEDs
Cap Types & Colors
Standard (1.5N)
(Black Switch Body)
A
Single or Bicolor LED
Cap Lens/Diffuser Colors
C
D
F
Red
Clear/White
(Combine with any LED)
High (2.5N)
(Gray Switch Body)
JB
H
Amber
Green
JC Clear/Red
JD Clear/Amber
JF Clear/Green
CF Bicolor Red/Green
DG Bicolor Amber/Blue
Bicolor Alternating
Legend Caps
Alternating Legends
11 ON (pos) OFF (pos)
12 ON (neg) OFF (neg)
Bicolor LED
CF Red/Green
DG Amber/Blue
JCF
Red/Green
Amber/Blue
JDG
13 START
14 OPEN
STOP
CLOSE
Nonilluminated
Solid Color Cap
Contact factory for custom
options.
N
No LED
A
B
Black
White
Red
C
H
Gray
Part Numbers for Alternating Legends
Color
Part Number
Red/Green
Amber/Blue
AT3023JCF11 ~ AT3023JCF14
AT3023JDG11 ~ AT3023JDG14
Refer to Ordering Table for Alternating Legend that
corresponds with last 2 digits of part number.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
NP0115HG03LF-JF
High (2.5N)
Operating Force
Clear Lens with Green Diffuser
Green LED
SPST
OFF-Momentary ON Circuit
Normally Open Contacts
Gold Contacts with 0.4VA Rating
Straight PC Terminals
D76
www.nkkswitches.com
Subminiature Smooth Actuation Pushbuttons
Series NP01
POLE & CIRCUIT
Illuminated Models
Plunger Position
Connected Terminals
Throw & Switch Schematic
( ) = Momentary
Normal
Down
Notes: Switch is marked with LC1, 1, L3, L4, L1,
L2, 2, LC2.
Pole
Model
Lamp circuit is isolated and requires an
external power source.
D
NP0115AG03L
NP0115HG03L
Normally
1-2
SP
OFF
(ON)
SPST
(+)
(-)
1
2
Open
Nonilluminated Models
Connected Terminals
Plunger Position
Throw & Switch Schematic
( ) = Momentary
Normal
Down
Note: Switch is marked with LC1, 1, L3, L4, L1,
L2, 2, LC2.
Pole
Model
NP0115AG03N
NP0115HG03N
Normally
1-2
SP
OFF
(ON)
SPST
1
2
Open
OPERATING FORCE
H
A
High Nominal Operating Force
2.5 0.8N
Standard Nominal Operating Force
1.5 0.5N
Switch base is Gray
Switch base is Black
CONTACTS, TERMINALS, & RATING
G03
Gold Contacts
Straight PC Terminals
0.4VA maximum @ 28V AC/DC maximum
ILLUMINATION
N
L
Nonilluminated
Illuminated
www.nkkswitches.com
D77
Series NP01
Subminiature Smooth Actuation Pushbuttons
LED COLORS & SPECIFICATIONS
R
I
F
LEDs are an integral part of the switch and not available separately.
The electrical specifications shown are determined at a basic
temperature of 25°C.
If the source voltage exceeds the forward voltage, a ballast resistor
is required. Specifications in parentheses ( ) below for Bicolor LED
denote simultaneous illumination of Red and Green.
E – VF
IF
+
R =
Anode
Where: R = Resistor Value (Ohms)
E = Source Voltage (V)
E
V
F
VF = Forward Voltage (V)
IF = Forward Current (A)
Cathode
–
Single Color LED
Bicolor LED
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
C
D
F
CF
DG
Color
Red
Amber
Green
Red
Green
Amber
30mA
20mA
2.0V
5V
Blue
30mA
20mA
3.2V
5V
D
Maximum Forward Current IFM
30mA
20mA
1.95V
5V
30mA
20mA
2.0V
5V
25mA
16mA
3.3V
5V
30 (25)mA 25 (25)mA
Typical Forward Current
Forward Voltage
IF
20 (20)mA
1.95V
5V
16 (5)mA
3.3V
VF
Maximum Reverse Voltage VRM
5V
0.41mA/°C 0.38mA/°C 0.33mA/°C 0.40mA/°C 0.33mA/°C 0.40mA/°C 0.40mA/°C
above 25°C above 25°C above 25°C above 25°C above 25°C above 25°C above 25°C
Current Reduction Rate
∆IF
Ambient Temperature Range
–25° ~ +50°C
–25° ~ +50°C
L4 (-)
L4 (-)
Blue
Green
L4 (-)
L3 (-)
LC2
(+)
LC2
(+)
LC2
(+)
L3 (-)
Red
L3 (-)
Amber
L2 (-)
L1 (-)
Red or
Green LEDs
Red/Green
Bicolor LED
Amber/Blue
Bicolor LED
LC1
(+)
Amber LED
L2 (-)
L2 (-)
Red
L2 (-)
Amber
LC1
(+)
LC1
(+)
LC1
(+)
L1 (-)
L1 (-)
Green
L1 (-)
Blue
CAP TYPES & COLORS
Cap for Single or Bicolor LED
(12.0) Sq
.472
AT3022
12mm Square Cap
(10.2)
.402
JB
JD
Clear Lens/Amber Diffuser
Clear Lens/Green Diffuser
Clear Lens/White Diffuser
Clear Lens/Red Diffuser
Material:
Polycarbonate Resin
JC
JF
Alternating Legend Cap for Bicolor LED
(12.0) Sq
.472
AT3023
12mm Square Cap
(10.2)
.402
JCF
Red/Green
Clear Lens
Alternating Legend Filter
Material:
Polycarbonate Resin
JDG
Amber/Blue
Standard Alternating Legend Pairs
11
12
13
14
STOP
CLOSE
OPEN
START
O N
OFF
O N
OFF
Green/Red
or
Blue/Amber
Green/Red
Green/Red
Green/Red
or
or
or
Blue/Amber
Blue/Amber
Blue/Amber
Cap illumination is alternating Green/Red or Blue/Amber; legend text is black.
Contact factory for other Alternating Legends.
Legend illustrations are approximate representations of the actual characters on the filters.
D78
www.nkkswitches.com
Subminiature Smooth Actuation Pushbuttons
Series NP01
CAP TYPES & COLORS (CONTINUED)
Solid Color Cap for Nonilluminated
(12.0) Sq
.472
AT3024
12mm Square Cap
A
C
(10.2)
.402
Red
Black
Material:
Polycarbonate Resin
B
H
Gray
White
TYPICAL SWITCH DIMENSIONS
Illuminated • Straight PC
D
(2.1)
.083
(2.0) Typ
.079
LC1
L4 L3
1
LC1
1 L3 L4
(7.0)
.276
(7.0)
.276
LC2
2
L2 L1
L1 L2 2 LC2
(0.3) Typ
.012
(1.0) Dia Typ
.039
C
L
(10.2)
.402
(0.5) Typ
.020
(12.0) Sq
.472
(12.5)
.492
(3.3)
.130
(2.0) Typ
.079
NP0115HG03LF-JF
PACKAGING
No
Code
Partitioned Tray
Any quantity. No code is required. Switches may be packaged with or without caps installed.
S
Stick-Tube Packaging
50 pieces per stick
(15.3)
.602
Switches must be ordered in 50-piece
increments when stick-tube packaging
is selected. This packaging is for the
switch body only. Caps will be packaged
separately.
(470.0)
18.504
(11.85)
.467
LEGEND ORIENTATION
Top View
Bottom View
LC1
1 L3 L4
Orient cap with legend as shown here, and “LC2” at lower right of switch body.
Orders for switches with legends will be assembled as illustrated.
OPEN
L1 L2 2 LC2
LC2
PRECAUTIONS FOR HANDLING & STORAGE
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
1. NP01 Pushbuttons are electrostatically sensitive. To prevent damage to LED, devices must
be properly isolated from static electricity.
2. Once the cap is installed onto the switch body, it cannot be removed.
3. When assembling cap, align projection on switch body to slot on inside of cap. (Refer to
illustration at right.)
Slot
4. * Legends may be printed on the lens with laser etch, screen print or pad print methods.
Epoxy based ink is recommended.
5. Do not use excessive force during installation on PC board or for cap installation.
Projection
* NKK Switches can provide custom legends for caps. Contact factory for more information.
www.nkkswitches.com
D79
相关型号:
©2020 ICPDF网 联系我们和版权申明