UB16KKG035C-CB [NKK]
Low Profile Pushbuttons; 薄型按键型号: | UB16KKG035C-CB |
厂家: | NIHON KAIHEIKI INDUSTRY CO. LTD. |
描述: | Low Profile Pushbuttons |
文件: | 总10页 (文件大小:341K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Series UB
Low Profile Pushbuttons
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver): 5A @ 125/250V AC or 5A @ 30V DC
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold
Insulation Resistance: 200 megohms minimum @ 500V DC
Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
Mechanical Life: 1,000,000 operations minimum for momentary;
200,000 operations minimum for alternate action
D
Electrical Life: 10,000 operations minimum for silver;
100,000 operations minimum for silver with resistive load of 3A @ 125V AC
200,000 operations minimum for gold
Nominal Operating Force: Single Pole: 1.9N for Square & 1.9N for Rectangular
Double Pole: 2.55N for Square & 3.1N for Rectangular
Contact Timing: Break before make
Travel: Pretravel .067” (1.7mm); Overtravel .024” (0.6mm); Total Travel .091” (2.3mm)
Materials & Finishes
Housing/Bezel: Glass fiber reinforced polyamide (UL94V-0)
Snap-in Frame: Stainless steel
Movable Contactor: Phosphor bronze
Movable Contacts: Silver alloy or copper with gold plating
Stationary Contacts: Silver alloy or copper with gold plating
Switch Terminals: Phosphor bronze with silver or gold plating
Lamp Terminals: Brass with silver plating
Base: Glass fiber reinforced liquid crystal polymer (UL94V-0)
Environmental Data
Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) for Illuminated
–20°C through +70°C (–4°F through +158°F) for Nonilluminated
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Cap Installation Force: 7.55N (1.70 lbf) maximum downward force on cap
Soldering Time & Temp: Wave Soldering (PC version): See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V-0 housing/bezel & base
UL: File No. E44145
All single & double pole models recognized at 5A @ 125/250V AC or 0.014A @ 28V DC.
Add “/U” to end of part number to order UL mark on switch.
Add “/CUL” to end of part number to order cULus mark on switch.
UL recognized only when ordered switch body with cap assembled.
CSA: CSA File No. 023535_0_000
All single & double pole models certified at 5A @ 125/250V AC or 5A @ 30V DC or
0.4VA maximum @ 28V AC/DC maximum.
Add “/C” to end of part number to order CSA mark on switch.
D78
www.nkk.com
Low Profile Pushbuttons
Series UB
Distinctive Characteristics
Bright or super bright LEDs (an integral part of the switch) of red,
amber, green, blue, or white, in full face or spot illumination
plus square or rectangular models.
Combination of PCB mountability and short body
allows use in compact applications.
D
Small behind panel dimension for snap-in
mounting in tight spaces.
Snap-acting contact mechanism provides
sensitive actuation with audible feedback;
quick-make, quick-break characteristic
limits arcing and prolongs electrical life.
Latchdown mechanism, independent of
switching mechanism, gives visible and
tactile indication of circuit status.
Terminals are epoxy sealed to lock out flux,
solvents, and other contaminants.
Momentary and alternate action circuits available in the
same space-saving body size.
Matching indicators available.
Actual Size
www.nkk.com
D79
Series UB
Low Profile Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
UB 1 5 SK G 03 5C
CC
Poles
Mounting Types
PCB Mounting
LEDs
Cap Types & Colors
1
2
SPDT
Full Face Illuminated Cap
for Bright LED
Bright LED
Red
DPDT
SK Square
5C
5D
5F
RK Rectangular
* Snap-in Mounting
KK Square
D
Lens/Diffuser Colors
Amber
Green
CB Red/White
FF Green/Green
*FJ Green/Clear
JB Clear/White
JC Clear/Red
Circuits
CC Red/Red
5
ON (ON)
NK Rectangular
*CJ Red/Clear
DB Amber/White
( ) = Momentary
ON ON
Rectangular with
NBK
6
Side Barriers
DD Amber/Amber JD Clear/Amber
*DJ Amber/Clear JF Clear/Green
Alternate Action
with Latchdown
* Standard with Solder
Lug terminals
FB Green/White *JJ Clear/Clear
Square & Rectangular Spot Illumi-
AB
nated Black Cap with White Window
Contacts & Ratings
Terminals
* Not available with Rectangular cap
Silver Rated 5A
@ 125/250V AC
Solder Lug*
01 (for Snap-in
Mounting)
W
Gold Rated 0.4VA max
@ 28V AC/DC max
Super Bright LED
Full Face Illuminated Cap
for Super Bright LED
G
03 Straight PC
6B
6F
White
Green
Blue
JB Clear Lens/White Diffuser
Spot Illuminated Black Cap
with White Window
6G
AB
* Wire harness & cable assemblies
offered only in Americas
Available with
Square only
For Square only; see cap detail page
Nonilluminated
Nonilluminated Cap Colors
IMPORTANT:
A
B
Black
White
Red
E
F
Yellow
Green
Blue
Switches are supplied without UL,
cULus, & CSA markings unless specified.
Specific models & ratings noted on
General Specifications page.
N
Nonilluminated
C
G
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
UB15SKG035C-CC
Red, Bright LED & Red Lens
with Red Diffuser
Gold Contacts with
0.4VA Rating
SPDT ON-(ON) Circuit
Straight PC Terminals
Square
with PCB Mounting
D80
www.nkk.com
Low Profile Pushbuttons
Series UB
POLES & CIRCUITS
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Switch/Lamp Schematics
Notes: Switch is marked with NC, NO, COM, L+ & L–.
Lamp circuit is isolated and requires an external
power source.
Normal
Down
Normal
Down
Pole
Model
1
COM
UB15
*UB16
ON
ON
(ON)
ON
SP
1-3
1-2
SPDT
DPDT
(+)
(-)
3
NC
2
NO
4
1
COM
2
COM
5
UB25
*UB26
ON
ON
(ON)
ON
DP
1-3 4-6
1-2 4-5
(+)
(-)
3
6
NC
NO
NC
NO
D
* When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the housing.
MOUNTING TYPES & SHAPES
PCB Mounting
SK
RK
(5.08)
.200
(2.54) Typ
.100
Square
(5.08) Typ
(2.54) Typ
.100
Rectangular
(7.62)
.300
(2.54) Typ
.100
(7.62) Typ
.300
(2.54) Typ
.100
.200
3
6
3
3
6
3
L +
L +
L -
L +
L +
2
1
(10.16)
.400
5
4
2
1
(10.16)
.400
2
1
2
1
5
4
(10.16)
.400
(10.16)
.400
L -
L -
L -
(1.2) Dia Typ
.047
(1.2) Dia Typ
.047
(1.2) Dia Typ
.047
(1.2) Dia Typ
.047
C
C
C
L
C
L
L
L
Double Pole
Single Pole
Double Pole
Snap-in Mounting (Solder Lug)
Single Pole
Square
with Built-in Bezel
Rectangular
with Built-in Bezel
Rectangular with Built-in
Side Barriers
KK
NK
NBK
(16.2)
.638
(16.2) Sq
.638
(22.4)
.882
Snap-in Mounting with Solder Lug terminals is the standard combination. Panel Thickness: .039 ~ .126” (1.0 ~ 3.2mm)
CONTACT MATERIALS & RATINGS
W
G
Silver Contacts
Gold Contacts
Power Level
5A @ 125V AC & 250V AC
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Complete explanation of operating range in Supplement section.
TERMINALS
(0.2)
(0.2)
.008
(4.0)
.157
.008
01
03
Solder Lug
Straight PC
(5.0)
.197
(1.6)
(1.0)
.063
(2.0)
.079
.039
(0.8)
.032
Thk = (0.5)
.020
Thk = (0.5)
.020
www.nkk.com
D81
Series UB
Low Profile Pushbuttons
LED COLORS & SPECIFICATIONS
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power
source. Polarity marks are on bottom of switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. Resistor
value can be calculated by using the formula in the Supplement section. LED is an integral part of switch and not available separately.
Bright
Super Bright
Super Bright LEDs are
Electrostatic Sensitive
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
5C
Red
30
5D
Amber
5F
Green
25
6B
White
30
6F
Green
6G
Blue
30
(+)
(-)
Color
IFM
IF
Unit
mA
Forward Peak Current
30
30
Continuous Forward Current
Forward Voltage
20
20
20
20
20
20
mA
VF
1.85
5
2.0
2.1
5
3.2
5
3.2
3.2
5
V
D
Reverse Peak Voltage
VRM
∆IF
5
5
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
0.40
0.42
0.46
0.40
0.40
.040
mA/°C
–25° ~ +50°C
–25° ~ +50°C
N
No Lamp
CAP TYPES & COLOR COMBINATIONS
Full Face Illuminated Cap for Bright LED
Lens/Diffuser
Lens/Diffuser
Colors Available for Square Cap:
Colors Available for Rectangular Cap:
AT4074
Lens
AT4117
(3.0)
CB DD
CC DJ
FJ
JB
JC
JD
JF
JJ
CB
CC
DB
DD
FB
FF
JB
JC
JD
JF
(3.0)
.118
.118
Lens
(17.0)
.669
(12.0)
(12.0) Sq
.472
.472
(0.5)
.020
AT4075
Diffuser
AT4118
Diffuser
CJ
FB
FF
(0.5)
.020
(15.35)
.604
(10.35)
.407
(10.35) Sq
.407
DB
Lens & Diffuser Material: Polycarbonate
Lens Finish: Glossy
Diffuser Finish: Textured
Spot Illuminated Caps for Bright & Super Bright LEDs
(1.9)
.075
(1.9)
(3.1)
.122
Cap/Window Colors Available:
.075
(3.1)
AT4119 Square
AT4120
Rectangular
for Bright LED
(5.0)
.197
.122
(5.0)
.197
Black Cap with Translucent
for Bright and
(3.0)
.118
AB
(3.0)
.118
White Window for LED Display
Super Bright LED
(17.0)
.669
(12.0)
.472
(12.0) Sq
.472
Material: Polycarbonate
Finish: Matte
Full Face Illuminated Cap for Super Bright LED
Lens/Diffuser
Colors Available for Square Cap:
Rectangular lens & diffuser are not
available for combining with super
bright LED.
AT4074 Lens & AT4075 Diffuser
(Dimensions above)
JB
Lens & Diffuser Material: Polycarbonate
Lens Finish: Glossy
Diffuser Finish: Textured
Opaque Caps for Nonilluminated
Cap Colors Available:
AT4073
Square
AT4116
Rectangular
(3.0)
.118
A
B
C
E
F
(3.0)
.118
(17.0)
.669
(12.0)
.472
(12.0) Sq
.472
Material: Polycarbonate
Finish: Glossy
G
Color Codes:
A Black
B White
C Red
D Amber
E Yellow
F Green
G Blue
J Clear
D82
www.nkk.com
Low Profile Pushbuttons
Series UB
TYPICAL SWITCH DIMENSIONS
ꢀ
Singleꢀ&ꢀDoubleꢀPoleꢀ
Squareꢀ•ꢀPCBꢀMount
(0.5)
.020
L +
3
6
N.C.
(5.08) Typ
.200
N.C.
(12.0) Sq
.472
2
5
N.O.
COM
N.O.
COM
1
L -
4
(2.54) Typ
.100
(0.5) Typ
.020
(1.0) Typ
(2.5)
.098
(1.0)
.039
.039
(5.08) Typ
.200
(15.24) Sq
.600
(10.0)
.394
(4.0)
.157
Latchdown Position
Single pole models do not have terminals 4, 5, & 6.
UB15SKG035C-CB
D
ꢀ
Singleꢀ&ꢀDoubleꢀPoleꢀ
Rectangularꢀ•ꢀPCBꢀMount
(0.5)
.020
L
+
6
3
(5.08) Typ
.200
N.C.
N.C.
(12.0)
.472
(15.24)
.600
2
N.O.
COM.
5
N.O.
COM
(2.54) Typ
.100
L
-
4
1
(0.5) Typ
.020
(17.0)
.669
(2.5)
.098
(1.0)
.039
(20.32)
.800
(10.0)
.394
(4.0)
.157
(1.0) Typ
.039
(7.62) Typ
.300
Latchdown Position
Single pole models do not have terminals 4, 5, & 6.
UB26RKG035D-DD
ꢀ
Singleꢀ&ꢀDoubleꢀPoleꢀ
Squareꢀ•ꢀSnap-inꢀMountꢀ•ꢀBuilt-inꢀBezel
(1.4)
(0.8) x (1.6) Typ
.055
.032 x .063
L +
3
6
N.C.
N.C.
(5.08) Typ
.200
(12.0) Sq
.472
(15.8)
.622
5
2
N.O.
N.O.
COM
COM
1
(2.54) Typ
.100
L -
4
(0.5) Typ
.020
(2.5)
.098
(1.0)
.039
(2.0) Typ
.079
(17.8) Sq
.701
(10.0)
.394
(5.0)
.197
(5.08) Typ
.200
Latchdown Position
Single pole models do not have terminals 4, 5, & 6.
UB25KKW015C-CB
ꢀ
Singleꢀ&ꢀDoubleꢀPoleꢀ
Rectangularꢀ•ꢀSnap-inꢀMountꢀ•ꢀBuilt-inꢀBezel
(1.4)
.055
(0.8) x (1.6) Typ
.032 x .063
L
+
6
3
(5.08) Typ
.200
N.C.
N.C.
(12.0)
.472
(17.8)
.701
(15.8)
.622
2
N.O.
COM.
5
N.O.
COM
(2.54) Typ
.100
L
-
4
1
(0.5) Typ
.020
(17.0)
.669
(2.5)
.098
(7.62) Typ
.300
(2.0) Typ
.079
(24.0)
.945
(1.0)
.039
(10.0)
.394
(5.0)
.197
(22.0)
.866
Latchdown Position
Single pole models do not have terminals 4, 5, & 6.
UB26NKW015F-FF
ꢀ
Singleꢀ&ꢀDoubleꢀPoleꢀ Rectangularꢀ•ꢀSnap-inꢀMountꢀ•ꢀBuilt-inꢀSideꢀBarriers
(0.8) x (1.6) Typ
.032 x .063
L
+
6
3
(5.08) Typ
.200
N.C.
N.C.
(12.0)
.472
(15.8)
.622
2
5
N.O.
N.O.
(17.8)
.701
COM.
COM
(2.54) Typ
.100
L
-
4
1
(0.5) Typ
.020
(2.0) Typ
.079
(17.0)
.669
(7.62) Typ
.300
(24.0)
.945
(22.0)
.866
(8.6)
(5.0)
(3.9)
.154
.339 .197
Single pole models do not have terminals 4, 5, & 6.
UB25NBKW015F-FB
D83
www.nkk.com
Series UB
Low Profile Pushbuttons
OPTIONAL ACCESSORIES
Spring Loaded Protective Guard for Snap-in Mounting of Square PCB Model
AT4173
Square Protective Guard/
Snap-in Frame
(10.5)
.413
(15.64)
.616
Opens 180°
Closes automatically
(20.5)
.807
Materials:
Cover: Clear Polycarbonate
Base: Black Polyamide
(18.4)
.724
(6.0)
.236
(9.0)
.354
(20.4)
.803
(15.64)
.616
Coil Spring: Stainless Steel
D
180°
Recommended
Panel Thickness:
.039” ~ .126”
(18.2) Sq
.717
(1.0mm ~ 3.2mm)
(39.0) Min*
1.535
Protective
Guard
AT4173
Recommended
2
Panel-to-PCB Range:
.354” ~ .433”
(10.5)
.413
Panel
(9.0mm ~ 11.0mm)
(20.5)
.807
Installation
1 Install switch onto
PC board.
2 Snap protective
guard into panel.
3 Join the two
assemblies.
3
Switch
(20.4)
.803
1
PC Board
(20.4)
(9.0) ~ (11.0)
.354 ~ .433
.803 (N)
(N) = Number of switches
* Minimum dimension allows opening of cover to 180°
Spring Loaded Protective Guard for Square Snap-in Model
AT4171
Square
Protective Guard
(10.5)
.413
(17.9)
.705
Opens 180°
Closes automatically
(20.5)
.807
(7.1)
.280
Cap Height
When
Assembled
(18.4)
.724
(14.2)
.559
(7.5)
.295
(20.4)
.803
(17.9)
.705
(16.2) Sq
.638
(39.0) Min*
1.535
AT4171
180°
(10.5)
.413
Materials:
(20.5)
.807
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(20.4)
.803
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
(20.4)
.803 (N)
(N) = Number of switches
* Minimum dimension allows opening of cover to 180°
D84
www.nkk.com
Low Profile Pushbuttons
Series UB
OPTIONAL ACCESSORIES
Spring Loaded Protective Guard for Snap-in Mounting of Rectangular PCB Model
AT4174
Rectangular
Protective Guard/
Snap-in Frame
(10.5)
.413
(15.64)
.616
(20.5)
.807
Opens 180°
Closes automatically
(24.6)
.969
Materials:
(26.6)
1.047
(6.0)
.236
(9.0)
.354
(20.54)
.809
Cover: Clear Polycarbonate
Base: Black Polyamide
Coil Spring: Stainless Steel
(23.4)
.921
D
180°
Recommended
Panel Thickness:
.039” ~ .126”
(18.2)
.717
(39.0) Min*
1.535
(1.0mm ~ 3.2mm)
Protective
Guard
AT4174
Recommended
Panel-to-PCB Range:
.354” ~ .433”
2
Panel
(10.5)
.413
Installation
(9.0mm ~ 11.0mm)
(20.5)
.807
1 Install switch onto
PC board.
3
Switch
2 Snap protective
guard into panel.
3 Join the two
assemblies.
(26.6)
1.047
1
PC Board
(9.0) ~ (11.0)
.354 ~ .433
(26.6)
1.047 (N)
(N) = Number of switches * Minimum dimension allows opening of cover to 180°
Spring Loaded Protective Guard for Rectangular Snap-in Model
AT4172
Rectangular
Protective Guard
(10.5)
.413
(17.9)
.705
Opens 180°
Closes automatically
(20.5)
.807
(7.1)
.280
Cap Height
When
(24.6)
.969
(20.4)
.803
Assembled
(22.4)
.882
(7.5)
.295
(26.6)
1.047
(24.1)
.949
(16.2)
.638
180°
(39.0) Min*
1.535
AT4172
Materials:
(10.5)
.413
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(20.5)
.807
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
(26.6)
1.047
(26.6)
1.047 (N)
(N) = Number of switches * Minimum dimension allows opening of cover to 180°
www.nkk.com
D85
Series UB
Low Profile Pushbuttons
OPTIONAL ACCESSORIES
Dust Covers
AT4001
Square
Not for use with barrier type models (mounting code NBK)
(16.5)
.650
(15.0) Sq
.591
(16.5)
.650
(24.0)
.945
AT4011
Rectangular
D
Cap Height
When
Assembled
(2.5)
.098
(22.7)
.894
(7.3)
.287
(24.0) Sq
.945
(30.2)
1.189
Materials:
PVC with polyethylene gasket
(PVC loses pliability below 0°C (32°F).)
Recommended Panel Thickness: .039” ~ .098” (1.0mm ~ 2.5mm)
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for UB Lens & Film Insert
Recommended Methods: Laser Etch on clear lens, Screen Print or Pad Print on lens;
Laser Print on film insert.
Square Cap
Shaded areas are printable areas.
Lens
UP
(10.48) (12.0)
.413 .472
Lens
(0.76) Typ
.030
(15.48)
.609
(0.76) Typ
.030
(10.48) Sq
.413
(0.76) Typ
.030
(17.0)
.669
(12.0) Sq
.472
Rectangular Cap
Lens
(0.5) R
.020
(0.5) R
.020
(8.78) (10.3)
.346 .406
Film Insert
Film
Insert
R
U
N
(8.78) Sq
.346
(10.3) Sq
.406
(0.76) Typ
.030
(0.76) Typ
.030
(13.78)
.543
(15.3)
.602
(0.76) Typ
.030
Diffuser
Film Insert: Clear Polyester 4 mil max. thickness
D86
www.nkk.com
Notes
www.nkk.com
D87
相关型号:
©2020 ICPDF网 联系我们和版权申明