YB15RKW01-05-BB [NKK]
Short Body Pushbuttons; 短身按钮开关型号: | YB15RKW01-05-BB |
厂家: | NIHON KAIHEIKI INDUSTRY CO. LTD. |
描述: | Short Body Pushbuttons |
文件: | 总12页 (文件大小:357K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Series YB
Short Body Pushbuttons
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver):
Logic Level (gold):
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
D
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Single pole: 1.47N for nonsealed; 1.67N for sealed
Double pole: 2.75N for nonsealed; 2.94N for sealed
Nonshorting (break-before-make)
Contact Timing:
Travel:
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Materials & Finishes
Housing/Bezel:
Snap-in Frame:
Base:
Glass fiber reinforced polyamide (UL94V-0)
Stainless steel
Diallyl phthalate resin (UL94V-0)
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Phosphor bronze with silver or gold plating
Silver alloy with silver plating or brass with gold plating
Silver alloy or copper with gold plating
Switch Terminals: Phosphor bronze with tin plating
Lamp Terminals: Phosphor bronze with tin plating
Environmental Data
Operating Temperature Range:
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Humidity:
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
2
Shock:
50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing:
IP65 of IEC60529 standard for panel seal models
Installation
Mounting Torque:
Quick Connect Force:
0.785Nm (6.95 lb•in) maximum
24.5N maximum downward force on connector
Manual Soldering: See Profile A in Supplement section.
Soldering Time & Temperature:
Standards & Certifications
Flammability Standards:
UL:
UL94V-0 housing & base
File No. E44145
All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/U” to end of part number to order UL mark on switch.
Add “/CUL” to end of part number to order cULus mark on switch.
File No. 023535_0_000
CSA:
All solder lug models certified at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/C” to end of part number to order CSA mark on switch.
D100
www.nkk.com
Short Body Pushbuttons
Series YB
Distinctive Characteristics
Full face or spot illumination with incandescent lamps or multi-element LEDs,
with or without resistors.
Choice of super bright LEDs in white, green, and blue as well as bright LEDs
in red, amber, and green.
Combination bezel-barrier is an integral part of the switch and
prevents accidental actuation.
D
Unique thermoplastic elastomer seal inside caps plus
rolled sleeve of nitrile butadiene rubber at joining of
housing and inner case, all for added protection to
interior mechanism.
Dust and oil tight as well as splashproof panel seal
models qualify to IP65 of IEC60529 Standards (similar
to NEMA 4 and 13). Panel seal models provided
with exterior o-ring.
Distinctive design of snap-action contacts for shock
resistance, long life, and sensitive actuation.
High density design to give behind panel depth of less than
one inch.
Terminals are epoxy sealed to lock out flux, dust, solvents, and other
contaminants.
Latchdown for indication of circuit status, plus audible, tactile feedback
with smooth, responsive operation.
Matching indicators available.
Actual Size
www.nkk.com
D101
Series YB
Short Body Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
YB 1 5
C K W 01
6 F
JB
Poles
Panel Seal
Housing
Terminals
Lamps
Cap Types & Colors
No
Solder Lug/.110”
(2.8mm) Quick Connect*
1
2
SPDT
K
Black only
Without Panel Seal
01
03
Code
DPDT
Incandescent Lamp
Solid Cap: Lens/Insert Colors
White/White
With Panel Seal
(Bushing Mount only)
Straight PC
W
05
12
5-volt
BB
CB
EB
FB
D
D
12-volt
Red/White
No
Yellow/White
Nonilluminated
Code
Circuits
Shapes
Contact Materials
& Ratings
Green/White
5
6
ON
(ON)
Bushing Mounting
GB
Blue/White
Silver Rated
3A @ 125V AC
( ) = Momentary
ON ON
S
Square
W
G
C
R
Round
LED for Spot Illuminated Cap
Spot Illuminated Cap: Lens/Insert Colors
Gold Rated 0.4VA max.
@ 28V AC/DC max.
Alternate Action
with Latchdown
Rectangular
LED Colors
Forward Voltage
JA
JB
JC
JE
JF
Clear/Black
Clear/White
Clear/Red
Snap-in Mounting
2-volt
(no resistor)
1C
1D
1F
Red
02
K
Square
Amber
Green
05
12
24
5-volt
M
N
Round
Clear/Yellow
Clear/Green
12-volt
Rectangular
1CF
Red/Green
24-volt
IMPORTANT:
LED Cap: Lens/Insert Colors
Clear/White
Bright LED
Switches are supplied without UL,
cULus & CSA markings unless specified.
Specific models & ratings noted on
General Specifications page.
* Wire harness & cable assemblies
offered only in Americas
JB
JC
JD
JF
LED Colors
Resistor
Clear/Red
No Code
05
No Resistor
5-volt
5C
Red
Clear/Amber
5D
5F
Amber
Green
Clear/Green
12
12-volt
24
24-volt
Super Bright LED
White
LED Cap: Lens/Insert Colors
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
YB15CKW01-6F-JB
6B
6F
JB
JB
Clear/White
Green
Blue
6G
Led Cap with Clear Lens
and White Insert
Green, Super Bright LED
Round with Bushing Mounting
Black Housing
Bicolor LED for Full Face Illuminated
LED Cap: Lens/Insert Colors
Without Panel Seal
LED Colors
Forward Voltage
Clear/White
2-volt
(no resistor)
02
Silver Contacts with
3 Amp Rating
SPDT ON-(ON) Circuit
2CF Red/Green 05
5-volt
Solder Lug/.110” (2.8mm)
Quick Connect Terminals
12
24
12-volt
24-volt
D102
www.nkk.com
www.nkk.com
D103
Series YB
Short Body Pushbuttons
POLES & CIRCUITS
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Switch/Lamp Schematics
Normal
Down
Normal
Down
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires
external power source.
Pole
Model
1 (COM)
YB15
*YB16
ON
ON
(ON)
ON
L (+)
(-) L
SP
1-3
1-2
SPDT
DPDT
3
1
2
(COM)
2
4
YB25
*YB26
ON
ON
(ON)
ON
L (+)
(-) L
DP
1-3 4-6
1-2 4-5
3
6
5
D
* When in latchdown position for the alternate circuit, cap position is .020” (0.5mm) above the built-in bezel.
PANEL SEAL
No Code
W
Without Panel Seal
With Panel Seal
Bushing
Mounting
Snap-in
Mounting
Bushing
Mounting
only
Supplied with
mounting nut
and o-ring AT089.
Supplied with
mounting nut.
SHAPES & MOUNTING TYPES
Bushing Mounting
Snap-in Mounting
S
C
R
K
M
N
Square
Round
Rectangular
Square
Round
Rectangular
Bezel-barrier is an integral part of the switch body.
HOUSING
Housing available in black only. The 1-piece body and bezel-barrier have a matte finish.
K
Black
CONTACT MATERIALS & RATINGS
W
Silver Contacts
Power Level
3A @ 125/250V AC
G
Gold Contacts
Logic Level
0.4VA max. @ 28V AC/DC max.
Complete explanation of operating range in Supplement section.
D104
www.nkk.com
Short Body Pushbuttons
Series YB
TERMINALS
Solder Lug/
01
Epoxy Seal
(7.3)
.110” (2.8mm) Quick Connect
.288
(2.0)
.079
(2.8)
.110
(1.2)
.047
Thk = (0.5)
.020
(3.7) Typ
.146
(3.7) Typ
.146
3
1
6
4
3
1
03
(4.4)
Straight PC
Epoxy Seal
.173
2
5
2
(0.6) R
.024
(4.85) Typ
.191
(4.85) Typ
.191
(2.8)
.110
Single Pole
Double Pole
(1.2)
.047
Thk = (0.5)
.020
(3.0)
.118
(1.6) Dia Typ
.063
(1.6) Dia Typ
.063
(5.55) Typ
.219
(3.0) Typ
.118
D
(5.55)
.219
C
C
L
L
INCANDESCENT LAMP & SOLID CAP
Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation.
For dimension drawing of lamp see the Accessories & Hardware section.
AT611
05
12
Voltage
V
I
5V AC
115mA
.150
12V AC
60mA
.150
Current
MSCP
T-1 Bi-pin
Endurance
Hours
7,000 average
–25°C ~ +50°C
Ambient Temperature Range
No Code
No Lamp
Solid Cap for Incandescent Lamp & Nonilluminated
(15.0) Dia
Lens/Insert
Colors Available:
AT3002
Round
.591
Translucent Colored Lens
Translucent White Insert
(12.2)
.480
(4.0)
.157
BB
White/White
Red/White
AT3001
Square
AT3003
Rectangular
CB
EB
FB
(15.0) Sq
.591
(21.0)
.827
Yellow/White
Green/White
Blue/White
(15.0)
.591
(12.2)
.480
(12.2)
.480
(4.0)
.157
Translucent White Seal/Filter
(4.0)
.157
GB
Materials:
Lens & Insert: Polycarbonate Seal/Filter: Thermoplastic Elastomer
Incandescent Lamp AT611
www.nkk.com
D105
Series YB
Short Body Pushbuttons
SPOT ILLUMINATED CAP WITH BUILT-IN LED
This spot-illuminated cap is factory assembled.
AT3010
Square
AT3011
Round
AT3012
Rectangular
(21.0)
.827
(15.0)
.591
(15.0) Sq
.591
(15.0) Dia
.591
(2.0)
.079
(2.0)
(2.0)
.079
.079
(12.2)
.480
(4.0)
.157
(12.2)
.480
(12.2)
(5.0)
.197
.480
(5.0)
.197
(5.0)
.197
(4.0)
.157
(4.0)
.157
(8.8)
.346
(8.8)
.346
(8.8)
.346
(+)
(-)
(+)
(+)
(-)
(-)
D
Colors Available:
02
05
12
24
1C
1D
1F
1CF
Red/Green
Without
Resistor
With
Resistor
With
Resistor
With
Resistor
Red
Amber
Green
Unit
Forward Peak Current
Continuous Forward Current
Forward Voltage
IFM
IF
20
15
15
12.5
5
15
12.5
12
12
10
mA
mA
V
VF
2.1
5
24
Reverse Peak Voltage (not applicable to bicolor)
Current Reduction Rate Above 25°C
Ambient Temperature Range
VRM
∆IF
5
5
5
V
0.27
––––
––––
––––
mA/°C
°C
–25 ~ +50
Without Resistor 2-volt
With Resistor 5, 12, 24-volt
(+)
(-)
(+)
(-)
(+)
(-)
(+)
(-)
Single Color
Bicolor
Single Color
Bicolor
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires
external power source. Single color LEDs are colored in OFF state. Bicolor LED is translucent white in OFF state.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Lens/Insert
Colors Available:
Clear Lens
Example part number
when cap is ordered separate
from switch:
JA
Clear/Black
AT3010F02JA
Colored Insert
Seal
for a
JB
JC
JE
JF
Clear/White
Clear/Red
Square Spot Illuminated Cap
with Green 2-volt LED
without resistor
Clear Lens and Black Insert
Clear/Yellow
Clear/Green
Materials:
Built-in LED
(integral part
of the cap)
Lens & Insert: Polycarbonate
Seal: Thermoplastic Elastomer
D106
www.nkk.com
Short Body Pushbuttons
Series YB
BRIGHT LED & LED CAPS
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Electrical Specifications for Bright LED without Resistor
Bright
AT628
Colors
Available:
5C
5D
5F
No Code
Unit
Red
Amber
Green
No Resistor
Red
40
26
1.9
4
Amber
Green
LED Colors
Forward Peak Current
Continuous Forward Current
Forward Voltage
IFM
IF
40
26
40
26
2.0
4
mA
mA
V
D
VF
2.0
(+)
(-)
Reverse Peak Voltage
VRM
∆IF
4
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
0.50
–25 ~ +50
mA/°C
°C
T-1 Bi-pin
Electrical Specifications for Bright LED with Resistor
Bright
AT634
Colors
5C
5D
5F
05
12
24
Available:
Red
Amber
Green
IFM
Unit
mA
mA
V
Forward Peak Current
—
25
5
—
—
10
Continuous Forward Current
Forward Voltage
IF
20
12
VF
24
Reverse Peak Voltage
VRM
∆IF
4
8
16
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
––––
––––
––––
mA/°C
°C
T-11⁄
Bi-pin
4
–25 ~ +50
AT634
5-volt,
2-element
AT634
12-volt,
4-element
with Resistor
AT634
24-volt,
4-element
with Resistor
(+)
(-)
(+)
(+)
(-)
(-)
with Resistor
Cap for Bright LED
AT3005
Lens/Insert
Colors Available:
AT3004
Square
(15.0) Sq
.591
(15.0) Dia
.591
Round
Transparent Clear Lens
(12.2)
.480
(12.2)
.480
(4.0)
.157
JB
Clear/White
(4.0)
.157
Translucent Colored Insert
JC
JD
JF
Clear/Red
(21.0)
.827
(15.0)
.591
Translucent White Seal/Diffuser
Clear/Amber
Clear/Green
Materials:
AT3006
Rectangular
(12.2)
.480
(4.0)
.157
Bright LEDs
Lens & Insert: Polycarbonate Seal/Diffuser: Thermoplastic Elastomer
AT628 AT634
www.nkk.com
D107
Series YB
Short Body Pushbuttons
SUPER BRIGHT LED & LED CAPS
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Electrical Specifications for Super Bright LED
Super Bright
AT625G Blue
AT631B White
AT632F Green
6B
6F
6G
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
(+)
(-)
Colors:
White
Green
Blue
Unit
D
Forward Peak Current
IFM
IF
30
20
3.6
5
30
20
30
20
3.6
5
mA
mA
V
Continuous Forward Current
Forward Voltage
VF
3.5
Reverse Peak Voltage
VRM
∆IF
5
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
0.50
–25 ~ +50
mA/°C
°C
T-1 Bi-pin
Cap for Super Bright LED
AT3014
Square
AT3015
Round
AT3016
Rectangular
(21.0)
.827
(15.0) Sq
.591
(15.0) Dia
.591
(15.0)
.591
(12.2)
.480
(12.2)
.480
(12.2)
.480
(4.0)
.157
(4.0)
.157
(4.0)
.157
Transparent Clear Lens
Translucent White Insert
Lens/Insert
Colors Available:
JB
Clear/White
Translucent White Seal/Diffuser
Super Bright LEDs
AT625 AT631
AT632
Materials:
Lens & Insert: Polycarbonate Seal/Diffuser: Thermoplastic Elastomer
D108
www.nkk.com
Short Body Pushbuttons
Series YB
BICOLOR LED & LED CAPS
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Electrical Specifications for Bicolor LED
02
05
12
24
Bicolor AT621
Bicolor LED is translucent white in OFF state.
Unit
IFM
IF
Forward Peak Current
60
45
60
45
20
15
12
10
mA
mA
2CF
Red/Green
D
Continuous Forward Current
Forward Voltage
VF
∆IF
2.1
0.80
5
12
24
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
––––
––––
––––
mA/°C
°C
T-11⁄
Bi-pin
2
–25 ~ +50
AT621
Bicolor LED
2-volt
6-element
without Resistor
AT621
Bicolor LED
5-volt
6-element
with Resistor
AT621
(+)
(-)
Bicolor LED
12 & 24-volt
6-element
with Resistor
(+)
(-)
(+)
(-)
As shown for Red;
Reverse polarity for Green
LED Caps
AT3004
Square
AT3005
Round
AT3006
Rectangular
(21.0)
.827
(15.0) Sq
.591
(15.0) Dia
.591
(15.0)
.591
(12.2)
.480
(12.2)
.480
(12.2)
.480
(4.0)
.157
(4.0)
.157
(4.0)
.157
Transparent Clear Lens
Lens/Insert
Colors Available:
Transparent White Insert
JB
Clear/White
Translucent White Seal/Diffuser
Materials:
Lens & Insert: Polycarbonate Seal/Diffuser: Thermoplastic Elastomer
Bicolor LED AT621
www.nkk.com
D109
Series YB
Short Body Pushbuttons
TYPICAL SWITCH DIMENSIONS
Square • Bushing Mounting
Single & Double Pole
(9.4)
(1.2) x (2.0) Typ
.047 x .079
(3.7)
.146
M16 P1
.370
(0.5) Typ
.020
NC
3
1
6
4
(9.7)
.382
L
2
5
- +
(2.8) Typ
.110
COM
(10.9)
.429
(7.3)
.288
(6.0)
.236
(11.1)
.437
(15.0) Sq
.591
(8.3)
.327
(24.3)
.957
(18.0) Sq
.709
D
YB15SKW01-12-CB
Round • Panel Seal
Single pole models do not have terminals 4, 5, & 6.
Single & Double Pole
(3.7)
.146
(9.4)
.370
(1.2) x (2.0) Typ
.047 x .079
M16 P1
(0.5)
.020
(0.5) Typ
.020
NC
3
1
6
4
(9.7)
.382
L
2
5
- +
(2.8) Typ
.110
COM
(6.0)
.236
(11.1)
.437
(15.0) Dia
.591
(0.5)
.020
(3.0)
.118
(10.9)
.429
(7.3)
.288
(18.0) Dia
.709
(5.3)
.209
(24.3)
.957
Latchdown Position
YB26WCKW01-12-EB
Single pole models do not have terminals 4, 5, & 6.
Rectangular • Snap-in Mounting
Single & Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
(0.5) Typ
.020
NC
3
1
6
4
(15.0)
.591
(18.0)
.709
(9.7)
.382
L
2
5
- +
(2.8) Typ
.110
COM
(7.3)
.288
(6.0)
.236
(11.1)
.437
(21.0)
.827
(8.3)
.327
(24.3)
.957
(24.0)
.945
YB15NKW01-5C-JC
Single pole models do not have terminals 4, 5, & 6.
PANEL THICKNESS & CUTOUTS
Bushing & Panel Seal Mount
Snap-in Mount
Panel Thickness
.020” ~ .197”
(0.5mm ~ 5.0mm)
Panel Thickness
.039” ~ .138”
(1.0mm ~ 3.5mm)
(1.2) R
.047
+ 0.2
+ 0.2
– 0.0
(16.0)
.630
Dia
(16.0)
Dia
– 0.0
.630
D110
www.nkk.com
Short Body Pushbuttons
Series YB
OPTIONAL ACCESSORIES
Dust Covers and Protective Guards reduce depth of switch behind panel by .047” (1.2mm).
Panel Thickness Range with Dust Cover or Protective Guards:
Bushing Mounting
.020” ~ .150” (0.5mm ~ 3.8mm)
Snap-in Mounting
.020” ~ .091” (0.5mm ~ 2.3mm)
Panel Seal
.020” ~ .118” (0.5mm ~ 3.0mm)
Dust/Splash Cover
Splash Cover
(16.2)
.638
AT4115 Dust Cover
for Snap-in or
Bushing Mount
Dust Cover
(5.9)
.232
AT089
AT541
AT4115
AT4115
(5.2)
.205
D
AT4115 Splash Cover
and AT541 O-ring
for Bushing Mount
(29.2)
1.150
(23.2)
.913
AT4115
(16.0) Dia
.630
Materials:
Snap-in Mount
Panel Seal
Lid: Polyvinyl Chloride
Base: Polyamide
O-ring: Nitrile butadiene rubber
(20.0) Dia
.787
Note: AT089 o-ring supplied
with panel seal model.
(0.5)
AT541
.020
Protective Guard
Assembled
Cap Height
(1.2)
.047
AT4072 Protective Guard
Opens 90°
Closes manually
(12.0)
.472
(22.9)
.902
Materials:
Lid: Polycarbonate
Base: Glass Fiber
Reinforced Polycarbonate
(1.2)
.047
(6.6)
.260
(11.2)
.441
(16.0) Dia
.630
(23.9)
.941
Spring Loaded Protective Guard
AT4175 Spring Loaded
Protective Guard
Opens 180°
Assembled
Bezel Height
Closes automatically
(12.5)
.492
(23.4)
.921
(16.0) Dia
.630
(45.0) Min*
1.772
(1.2)
.047
(11.4)
.449
(16.0) Dia
.630
(23.9)
.941
AT4175
180
°
(12.5)
.492
(23.4)
.921
Materials:
Lid: Polycarbonate
Base: Glass Fiber Reinforced Polyamide
Coil Spring: Stainless Steel
(23.9)
.941
(24.0) Min
.945
* Minimum dimension allows opening of cover to 180°
www.nkk.com
D111
Series YB
Short Body Pushbuttons
ASSEMBLY INSTRUCTIONS
Cap Assembly
LED Polarity & Orientation in Lamp Socket
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Spot
Plunger
Pinhole
Grip Slot
Projections
Positive
Lamp Socket
Negative
Lamp Socket
Flat
Flat
(+)
Flat
(+)
Switch
Body
(+)
(+)
(-)
(-)
(-)
Part Number
(-)
Top View of Switch
LED
AT628
AT634
LEDs
AT625G
AT631B AT632F
LED
AT621
Spot Illuminated Cap
with Built-in LED
D
The following installation tools are available: AT106 Socket Wrench for bushing mounting (Overtightening the mounting nut AT092
may damage the switch housing.); AT109 Cap Extractor; AT111 Lamping Tool.
Further details and dimensions are shown in the Accessories and Hardware section.
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for YB Lens
Recommended Methods: Laser Etch on clear lens, Screen Print or Pad Print on Lens.
Epoxy based ink is recommended.
O
(13.48) (15.0)
.531 .591
N
(0.76) Typ
.030
(13.48) Sq
.531
(0.76) Typ
.030
(19.48)
.767
(0.76) Typ
.030
(13.48) Dia
.531
(0.76) Typ
.030
(21.0)
.827
(15.0) Dia
.591
(15.0) Sq
.591
Shaded areas are printable areas.
Suggested Printable Area for Film Insert
Recommended Print Method: Laser Print
Lens
Film Insert: Clear Polyester, 4 mil max. thickness
Film
Insert
O
N
Filter
Seal
(9.88) (11.4)
.389 .449
(10.68) (12.2)
.420 .480
(0.76) Typ
.030
(16.68)
.657
(0.76) Typ
.030
(10.68) Sq (0.76) Typ
(0.76) Typ
.030
(10.68)
.420
(0.76) Typ
.030
.420
.030
(18.2)
.717
(12.2) Sq
.480
(12.2)
.480
Cap
Base
Shaded areas are printable areas.
D112
www.nkk.com
相关型号:
YB15RKW03
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15RKW03-05-BB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15RWG01-05-BB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKG01
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKG03
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKW01
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKW01-05-BB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKW01-05-JB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKW01-12-CB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
GREATECS
YB15SKW03
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SKW03-05-BB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
YB15SWG01-05-BB
Short Body PushbuttonsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
NKK
©2020 ICPDF网 联系我们和版权申明