YB215CWCKG01-5F-JB [NKK]
22mm Panel Seal Pushbuttons; 22毫米面板密封按钮开关
| 型号： | YB215CWCKG01-5F-JB |
| 厂家： | 
NIHON KAIHEIKI INDUSTRY CO. LTD. |
| 描述： | 22mm Panel Seal Pushbuttons |
| 文件： | 总8页 (文件大小：311K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series YB2
22mm Panel Seal Pushbuttons
General Specifications
Electrical Capacity (Resistive Load)
Power Level (silver):
Logic Level (gold):
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
D
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Single pole: 1.5N
Double pole: 3.0N
Contact Timing:
Travel:
Nonshorting (break-before-make)
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Materials & Finishes
Bezel:
Housing:
Black: Glass fiber reinforced polyamide (UL94V-0); Silver: Polycarbonate
Glass fiber reinforced polyamide (UL94V-0)
Diallyl phthalate resin (UL94V-0)
Base:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Phosphor bronze with silver or gold plating
Phosphor bronze & silver alloy
Silver alloy or copper with gold plating
Switch Terminals: Phosphor bronze with tin plating
Lamp Terminals: Phosphor bronze with tin plating
Environmental Data
Operating Temperature Range:
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Humidity:
Vibration:
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
2
Shock:
50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing:
IP65 of IEC60529 standard
Installation
Mounting Torque:
0.785Nm (6.95 lb•in) maximum
Soldering Time & Temperature:
Manual Soldering: 390°C maximum for 4 seconds maximum
Standards & Certifications
Flammability Standards:
UL:
UL94V-0 housing, base & black or metallic silver bezel
File No. E44145
All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/CUL” to end of part number to order cULus mark on switch.
D114
www.nkk.com
22mm Panel Seal Pushbuttons
Series YB2
Distinctive Characteristics
22mm pushbutton with the shortest above-panel dimension (1.8mm) in the industry
for splashproof design.
Meets IP65 of IEC60529 standards (similar to NEMA 4 and 13), providing
dust tight and splashproof panel seal protection.
Tamper resistant 19mm diameter actuator.
D
Short body of .965” (24.5mm) conserves behind-panel
space.
Distinctive long stroke and light touch actuation for clear
indication of circuit status.
Choice of cap colors includes clear, red, green, amber,
or metallic silver for enhanced panel appearance.
Metallic silver cap option has bright ring illumination.
Brilliant illumination with multiple LED colors.
Bezel color options in silver or black.
Available in momentary and alternate action with latchdown.
Crisp actuation and clear circuit status provided by snap-action
contact mechanism. Arc barrier protects against crossover.
Combination solder lug and .110” quick connect terminals. Terminals
are epoxy sealed to lock out flux, dust, solvents, and other contaminants,
as well as to secure terminals and improve contact stability.
Actual Size
Custom legends on actuator available.
www.nkk.com
D115
Series YB2
22mm Panel Seal Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
1 5 C W C K W 01
6 F
JB
YB2
Poles
Contact Point
Shape
Terminals
LEDS
Cap Types & Colors
D
D
1
2
SPDT
DPDT
Normally Open and
Normally Closed
C
Round
Solder Lug/.110”
(2.8mm) Quick Connect*
01
C
Bright LED
Lens/Diffuser Colors
Clear/White
LED Colors
Resistor
JB
JS
No Resistor
(not for
Green)
Metallic Silver Cap/Clear Ring
Red/White
5C Red
No
Code
CB
EB
FB
Yellow/White
5D Amber
5F Green
05
12
24
5-volt
Circuits
Panel Seal
Bezel
Contact Materials
& Ratings
Green/White
12-volt
24-volt
5
ON
) = Momentary
ON ON
(ON)
W
With Panel Seal
K
Black
LED & cap need to be the same color.
Yellow cap pairs with amber LED to achieve
amber illumination. Codes JB & JS may
be combined with all LED colors.
Silver
(
S
Metallic Silver
W
G
Rated 3A @ 125V AC
6
Gold
Alternate Action
with Latchdown
Rated 0.4VA maximum @
28V AC/DC maximum
Super Bright LED
White
Lens/Diffuser Cap Colors
6B
6F
JB
JS
Clear/White
Green
Metallic Silver Cap/Clear Ring
* Wire harness & cable assemblies
offered only in Americas
IMPORTANT:
6G
Blue
Switches are supplied without
cULus marking unless specified.
Specific models & ratings noted
on General Specifications page.
Nonilluminated
Cap Color
Metallic Silver
Clear/White
Red/White
N
No Lamp
S
JB
CB
EB
FB
Yellow/White
Green/White
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
YB215CWCKW01-6F-JB
Green, Super Bright LED
LED Cap with Clear Lens
& White Diffuser
Black Bezel
Round Black Housing
With Panel Seal
SPDT
ON-(ON) Circuit
Silver Contacts with
3 Amp Rating
Solder Lug/.110” (2.8mm)
Quick Connect Terminals
D116
www.nkk.com
www.nkk.com
D117
Series YB2
22mm Panel Seal Pushbuttons
POLES & CIRCUITS
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Switch/Lamp Schematics
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires an
external power source.
Normal
Down
Normal
Down
Pole
Model
1 (COM)
YB215
YB216
ON
ON
(ON)
ON
L (+)
(-) L
(-) L
SP
1-3
1-2
SPDT
3 NC
2 NO
1
(COM)
6 NC
4
YB225
YB226
ON
ON
(ON)
ON
L (+)
DP
1-3 4-6
1-2 4-5
DPDT
3 NC
2 NO
5 NO
D
CONTACT POINT
PANEL SEAL
C
W
Panel Seal
Normally Open and Normally Closed
Contact points are both Normally Open and
Normally Closed.
Two o-rings provide
panel seal protection
meeting IP65 of
IEC60529 standards.
SHAPE
BEZEL
C
K
S
Round
Black
Metallic Silver
CONTACT MATERIALS & RATINGS
W
G
Silver Contacts
Gold Contacts
Power Level: 3A @ 125/250V AC
Switch base is green
Logic Level: 0.4VA max. @ 28V AC/DC max.
Switch base is red
TERMINALS
Solder Lug/
.110” (2.8mm) Quick Connect
01
Epoxy Seal
(7.3)
.288
(2.0)
.079
(2.8)
.110
(1.2)
.047
Thk = (0.5)
.020
D118
www.nkk.com
22mm Panel Seal Pushbuttons
Series YB2
BRIGHT & SUPER BRIGHT LEDS
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and
requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required.
Base of AT634 and AT636 is Black for 5V, Light Blue for 12V and Gray for 24V.
Electrical Specifications for Bright LED without Resistor
Colors
Bright
AT628
5C
5D
No Code
Red
Amber
Available:
No Resistor
Amber
Unit
LED Colors
Red
40
26
1.9
4
Forward Peak Current
IFM
IF
40
26
2.0
4
mA
mA
V
Continuous Forward Current
Forward Voltage
T-1 Bi-pin
VF
D
Reverse Peak Voltage
VRM
∆IF
V
(+)
(-)
Current Reduction Rate Above 25°C
Ambient Temperature Range
0.50
–25 ~ +50
mA/°C
°C
Electrical Specifications for Bright Red & Amber LED with Resistor
Bright
AT634
Colors
5C
5D
05
12
24
Red
Amber
IFM
Available:
Unit
mA
mA
V
Forward Peak Current
—
25
5
—
—
10
24
16
—
Continuous Forward Current
Forward Voltage
IF
20
VF
12
Reverse Peak Voltage
VRM
∆IF
4
8
—
V
T-11⁄
Bi-pin
4
Current Reduction Rate Above 25°C
Ambient Temperature Range
—
mA/°C
°C
–25 ~ +50
AT634
5-volt,
2-element
AT634
12-volt,
4-element
AT634
24-volt,
4-element
(+)
(-)
(+)
(+)
(-)
(-)
with Resistor
with Resistor
with Resistor
Electrical Specifications for Bright Green LED with Resistor
Bright
AT636
Colors
ATTENTION
ELECTROSTATIC
5F
05
12
24
Available:
Unit
mA
mA
V
Green
IFM
SENSITIVE DEVICES
Forward Peak Current
—
11
5
—
—
8.7
24
5
Continuous Forward Current
Forward Voltage
IF
9.5
T-11⁄
Bi-pin
4
VF
12
(-)
(+)
(+)
5V
Reverse Peak Voltage
VRM
∆IF
5
5
—
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
—
—
mA/°C
°C
(-)
12V & 24V
–25 ~ +50
Electrical Specifications for Super Bright LED
Super Bright
AT625G Blue
AT631B White
AT632F Green
ATTENTION
ELECTROSTATIC
6B
White
6F
Green
30
6G
Blue
30
(+)
(-)
SENSITIVE DEVICES
Colors:
IFM
Unit
mA
mA
V
Forward Peak Current
30
Continuous Forward Current
Forward Voltage
IF
20
20
20
VF
3.6
5
3.5
5
3.6
5
Reverse Peak Voltage
VRM
∆IF
V
Current Reduction Rate Above 25°C
Ambient Temperature Range
0.50
mA/°C
°C
T-1 Bi-pin
–25 ~ +50
www.nkk.com
D119
Series YB2
22mm Panel Seal Pushbuttons
BALLAST RESISTOR CALCULATION FOR LEDS
E – VF
IF
R
I
F
+
R =
If the source voltage is greater than the rated voltage of
a lamp or LED, a ballast resistor must be connected in
series with the lamp. This circuit diagram and formula
will assist in calculating the value of the required ballast
resistor.
Anode
Where: R = Resistor Value (Ohms)
E = Source Voltage (V)
E
V
F
VF = Forward Voltage (V)
IF = Forward Current (A)
Cathode
–
CAPS & CAP COLORS
AT3017 Cap for
Bright LED
AT3018 Cap for
Super Bright LED
AT3019 Cap for
Nonilluminated
AT3020 Cap with
Illumination Ring for
Bright or Super Bright LED
D
Lens/Diffuser Colors Available:
Lens/Diffuser Colors Available:
Cap Color Available:
Cap Color Available:
Metallic Silver with
Clear Ring
JB
JB
S
JS
Clear/White
Clear/White
Metallic Silver
CB
Red/White
Note: AT3017 Cap can
also be used without
illumination.
(19.0) Dia
.748
(19.0) Dia
.748
EB
*Yellow/White
(13.1)
.516
(13.1)
.516
FB
(4.9)
.193
(4.9)
.193
Green/White
(19.0) Dia
.748
(19.0) Dia
.748
(13.1)
.516
(13.1)
.516
*Yellow cap
pairs with
(4.9)
.193
(4.9)
.193
Materials
Lens: Polycarbonate
Insert: Polyester
amber LED
to achieve
amber illumination.
Material for Lens & Diffuser: Polycarbonate
TYPICAL SWITCH DIMENSIONS
Single Pole
Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
M16 P1
(3.7)
.146
.047 x .079
(0.5) Typ
.020
NC
L
NC
3
1
3
1
6
4
L
(9.7)
.382
(9.7)
.382
2
2
5
-
+
- +
COM
COM
(2.8) Typ
.110
(7.3)
.288
(3.0)
.118
(19.0) Dia
.748
(1.8)
.071
(6.0)
.236
(33.6)
1.323
(5.55)
.219
(11.1)
.437
(25.0) Dia
.984
YB215CWCKW01-6F-JB
PANEL THICKNESS & CUTOUT
+ 0.3
– 0.0
Dia Typ
(25.4) Min
1.00
(22.0)
.866
Panel Thickness
.020” ~ .197”
(0.5mm ~ 5.0mm)
(25.4) Min
1.00
Side-by-side Mounting
(10.5)
.413
(1.7) Typ
.067
D120
www.nkk.com
22mm Panel Seal Pushbuttons
Series YB2
ASSEMBLY INSTRUCTIONS
1. Remove knurled
mounting nut.
5. Install the red o-ring which
was removed in step 2 at
the inside bottom of the
bezel.
Red O-ring
Bezel
Knurled
Mounting Nut
6. Align tab inside of the bezel with keyway on housing and
bring bezel back into its original position.
2. Remove bezel and red
o-ring from housing.
There are two o-rings
in this assembly: one is
D
Keyway
Housing
Orange
O-ring
red, one is orange.
Bezel
Red O-ring
Red
O-ring
Tab
Part Number
This Side
Bezel
Cathode
Socket (–)
3. Install LED.
Anode
Back of
Bezel
Socket (+)
7. Before installing into panel,
make sure that the orange
o-ring is present at the back
of the bezel. Align keyway
on bezel with tab in panel
and push switch all the way
into the panel.
Bezel
LEDs
Keyway
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
AT634 & AT636
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
D-Flat
(+)
(–)
Panel
Tab
LED AT628
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
D-Flat
8. Attach mounting nut behind panel and tighten. Make
sure that bezel and actuator fit properly and that there is
no space between bezel and panel. Do not overtighten.
Mounting torque: 0.785Nm (6.95 lb•in) maximum.
Optional socket wrench AT106 available.
(+)
(–)
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
LEDs AT625G,
AT631B,
AT632F
The larger metal part within the LED
represents the cathode (–). Align LED
for appropriate polarity and insert LED
into base.
Actuator
Bezel
Cathode (–)
Anode (+)
(–)
(+)
Panel
Actuator
4. Align tabs (B) on both
sides of actuator with
the projections (A) inside
of the housing and push
actuator firmly down to
snap in.
B
Knurled
Mounting Nut
A
Housing
AT106 Socket Wrench
www.nkk.com
D121
Series YB2
22mm Panel Seal Pushbuttons
LEGENDS
NKK Switches can provide custom legends for caps. Contact factory for more information.
Recommended Methods: Laser Etch on clear cap, Screen Print or Pad Print on cap.
Epoxy based ink is recommended.
Shaded Area is Printable Area for Caps
AT3017, AT3018 and AT3019
Shaded Area is Printable Area for Cap
AT3020 (with clear ring for illumination)
D
(0.76) Typ
.030
(17.48) Dia
.688
(15.88) Dia
.625
(1.56) Typ
.062
(19.0) Dia
.748
(19.0) Dia
.748
Shaded Area is Printable Area for Film Inserts
(0.1)
.0039
+/–
(0.6) R Typ
.024
(1.2)
.047
Typ
Film Material and Thickness:
(14.78)
+(0.08) .0031
– (0.1) .0039
.582 (16.3)
Clear Polyester, 4 mil max.
.642
Recommended Print Method:
(15.88)
.625
(0.76) Typ
.030
Screen Print; Epoxy based ink is recommended
+(0.08) .0031
(17.4)
.685
– (0.1) .0039
HANDLING & PRECAUTIONS
LEDs are electrostatic sensitive devices. When installing and handling LEDs, use an electrostatic
protected work station to prevent LED damage.
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
D122
www.nkk.com
相关型号：
©2020 ICPDF网 联系我们和版权申明