COP822CJ [NSC]
8-Bit CMOS ROM Based Microcontrollers with 1k or 2k Memory, Comparator and Brown Out Detector; 基于8位CMOS微控制器的ROM与1K或2K的内存，比较器和欠压检测器
| 型号： | COP822CJ |
| 厂家： | 
National Semiconductor |
| 描述： | 8-Bit CMOS ROM Based Microcontrollers with 1k or 2k Memory, Comparator and Brown Out Detector |
| 文件： | 总35页 (文件大小：499K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
September 1999
COP820CJ/COP840CJ Family
8-Bit CMOS ROM Based Microcontrollers with 1k or 2k
Memory, Comparator and Brown Out Detector
Family features include an 8-bit memory mapped architec-
ture, 10MHz CKI with 1us instruction cycle, one multi-
General Description
The COP820CJ/840CJ Family ROM based microcontrollers
™
function 16-bit timer/counter, MICROWIRE/PLUS serial
™
are integrated COP8 Base core devices with 1k or 2k
I/O, one analog comparator, power saving HALT mode,
MIWU, on-chip R/C oscillator capacitor (COP840CJ), high
current outputs, software selectable I/O options, WATCH-
memory, an Analog comparator and Brownout detection.
These single-chip CMOS devices are suited for lower-
functionality applications where power and voltage fluctua-
tions are a consideration. Pin and software compatible (no
Brownout; different Vcc range) 4k/32k OTP versions are
available (COP87LxxCJ/RJ Family) for pre-production, and
for use with a range of COP8 software and hardware devel-
opment tools.
™
DOG timer, modulator/timer, Brownout detector, Power on
Reset, 2.5v-6.0v operation, and 16/20/28 pin packages.
In this datasheet, the term COP820CJ refers to packages in-
cluding the COP820CJ, COP822CJ, and COP823CJ; and
COP840CJ refers to COP840CJ, COP842CJ, COP940CJ,
and COP942CJ.
Devices included in this data sheet are:
Device
Memory (bytes) RAM (bytes) I/O Pins
Packages
Temperature
Comments
COP820CJ
COP822CJ
COP823CJ
COP840CJ
COP940CJ
COP842CJ
COP942CJ
1k ROM
1k ROM
1k ROM
2k ROM
2k ROM
2k ROM
2k ROM
64
54
24
16
12
24
24
16
16
28 DIP/SOIC -40 to +85˚C
20 DIP/SOIC -40 to +85˚C
64
16 SOIC
-40 to +85˚C
128
128
128
128
28 DIP/SOIC -40 to +85˚C
28 DIP/SOIC -0 to +70˚C
20 DIP/SOIC -40 to +85˚C
20 DIP/SOIC -0 to +70˚C
Low EMI
2.5V-4.5V, CJH = 4V-6V
2.5V-4.5V, CJH = 4V-6V
n Schmitt trigger inputs on Port G
n MICROWIRE/PLUS serial I/O
Key Features
n Multi-Input Wake Up (on the 8-bit Port L)
n Brown out detector
CPU/Instruction Set Feature
n 1 µs instruction cycle time
n Three multi-source vectored interrupts servicing
— External interrupt with selectable edge
— Timer interrupt
n Analog comparator
n Modulator/timer (High speed PWM for IR transmission)
n 16-bit multi-function timer supporting
— PWM mode
— External event counter mode
— Input capture mode
— Software interrupt
n 8-bit Stack Pointer (SP)—stack in RAM
n Two 8-bit register indirect data memory pointers (B, X)
n 1024 or 2048 bytes of ROM
n 64 or 128 bytes of RAM
n Quiet design (low radiated emissions)
n Integrated capacitor for the R/C oscillator for COP840CJ
Fully Static CMOS
<
n Low current drain (typically 1 µA)
n Single supply operation: 2.5V to 6.0V
n Temperature ranges: −0˚C to +70˚C and −40˚C to +85˚C
I/O Features
n Software selectable I/O options (TRI-STATE® output,
push-pull output, weak pull-up input, high impedance
input)
Development Support
n Emulation and OTP devices
n Real time emulation and full program debug offered by
MetaLink Development System
n High current outputs (8 pins)
n Packages
— 16 SO with 12 I/O pins for COP820CJ
— 20 DIP/SO with 16 I/O pins
— 28 DIP/SO with 24 I/O pins
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
™
™
™
™
COP8 , MICROWIRE , MICROWIRE/PLUS and WATCHDOG are trademarks of National Semiconductor Corporation.
iceMASTER® is a registered trademark of MetaLink Corporation.
© 2000 National Semiconductor Corporation
DS011208
www.national.com
Block Diagram
DS011208-1
2k ROM and 128 Bytes RAM for COP840CJ
FIGURE 1. Block Diagram
Connection Diagrams
DS011208-5
DS011208-4
Top View
Order Number COPCJ823-XXX/WM
See NS Package Number M16B
Top View
Order Number COPCJ822-XXX/N or
COPCJ822-XXX/M
DS011208-3
Top View
Order Number COPCJ820-XXX/N or
COPCJ820-XXX/M,
Order Number COPCJ840-XXX/N or
COPCJ840-XXX/M,
Order Number COPCJ940-XXX/N or
COPCJ940-XXX/M
Order Number COPCJ842-XXX/N or
COPCJ842-XXX/M
Order Number COPCJ942-XXX/N or
COPCJ942-XXX/M
See NS Package Number N20A or
M20B
See NS Package Number N28B or
M28B
FIGURE 2. Connection Diagrams
www.national.com
2
Connection Diagrams (Continued)
COP820CJ/COP840CJ Pin Assignment
Port Pin
L0
Typ.
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
ALT Function
MIWU/CMPOUT
MIWU/CMPIN−
MIWU/CMPIN+
MIWU
16-Pin
20-Pin
7
28-Pin
11
12
13
14
15
16
17
18
25
26
27
28
1
5
6
L1
8
L2
7
9
L3
8
10
11
12
13
14
17
18
19
20
1
L4
MIWU
9
L5
MIWU
10
11
12
L6
MIWU
L7
MIWU/MODOUT
INTR
G0
G1
G2
G3
G4
G5
G6
G7
I0
TIO
SO
SK
15
16
1
2
2
SI
3
3
I
CKO
2
4
4
I
7
I1
I
8
I2
I
9
I3
I
10
19
20
21
22
6
D0
O
D1
O
D2
O
D3
O
VCC
GND
CKI
RESET
4
13
3
6
15
5
23
5
14
16
24
3
www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Current into VCC pin (Source)
Total Current out of GND pin (sink)
Storage Temperature Range
Note 1: Absolute maximum ratings indicate limits beyond which damage to
the device may occur.
80 mA
80 mA
−65˚C to +150˚C
Supply Voltage (VCC
Voltage at any Pin
)
7.0V
DC and AC electrical specifications are not ensured when operating the de-
vice at absolute maximum ratings.
−0.3V to VCC + 0.3V
DC Electrical Characteristics
−0˚C ≤ TA ≤ + 70˚C for COP94x and −40˚C ≤ TA ≤ +85˚C for all others
Parameter Conditions
Operating Voltage Brown Out Disabled
Min
2.5
2.5
4.5
Typ
Max
6.0
Units
V
V
V
V
COP94xCJ
Brown Out Disabled
Brown Out Disabled
Peak to Peak
4.5
COP94xCJH
6.0
Power Supply Ripple 1 (Note 2)
Supply Current (Note 3)
CKI = 10 MHz
0.1 VCC
VCC = 6V, tc = 1 µs
6.0
3.5
2.0
1.5
10
mA
mA
mA
mA
µA
CKI = 4 MHz
VCC = 6V, tc = 2.5 µs
VCC = 4.0V, tc = 2.5 µs
VCC = 4.0V, tc = 10 µs
VCC = 6V, CKI = 0 MHz
CKI = 4 MHz
CKI = 1 MHz
<
HALT Current with Brown Out
Disabled (Note 4)
1
HALT Current with Brown Out
Enabled
VCC = 6V, CKI = 0 MHz
<
50
110
µA
COP840CJ Supply Current (Note
3)
CKI = 10 MHz, R = 2.2k
CKI = 4 MHz, R = 4.7k
CKI = 4 MHz, R = 4.7k
CKI = 1 MHz, R = 20k
VCC = 6V, tc = 1 µs
8.0
6.0
2.5
1.5
8
mA
mA
mA
mA
µA
VCC = 6V, tc = 2.5 µs
VCC = 4.5V, tc = 2.5 µs
VCC = 4.5V, tc = 10 µs
VCC = 6V, CKI = 0 MHz
<
HALT Current with Brown Out
Disabled
2.2
<
HALT Current with Brown Out
Enabled
VCC = 6V, CKI = 0 MHz
50
100
µA
Brown Out Trip Level (Brown Out
Enabled)
1.8
1.9
3.1
3.1
4.2
3.9
V
V
COP840CJ Brown Out Trip Level
(Brown Out Enabled)
INPUT LEVELS (VIH, VIL)
Reset, CKI:
Logic High
0.8 VCC
0.7 VCC
V
V
Logic Low
0.2 VCC
All Other Inputs
Logic High
V
V
Logic Low
0.2 VCC
+2
Hi-Z Input Leakage
Input Pullup Current
L- and G-Port Hysteresis (Note 6)
VCC = 6.0V
−2
µA
µA
V
VCC = 6.0V, VIN = 0V
−40
−250
COP840CJ
0.05 VCC
0.35 VCC
www.national.com
4
DC Electrical Characteristics (Continued)
−0˚C ≤ TA ≤ + 70˚C for COP94x and −40˚C ≤ TA ≤ +85˚C for all others
Parameter
Output Current Levels
D Outputs:
Conditions
Min
Typ
Max
Units
Source
VCC = 4.5V, VOH = 3.8V
−0.4
−0.2
10
mA
mA
mA
mA
mA
VCC = 2.5V, VOH = 1.8V
VCC = 4.5V, VOL = 1.0V
VCC = 2.5V, VOH = 0.4V
VCC = 4.5V, VOL = 2.5V
Sink
2
L4–L7 Output Sink
All Others
15
Source (Weak Pull-up Mode)
VCC = 4.5V, VOH = 3.2V
VCC = 2.5V, VOH = 1.8V
VCC = 4.5V, VOH = 3.8V
VCC = 2.5V, VOH = 1.8V
VCC = 4.5V, VOL = 0.4V
VCC = 2.5V, VOL = 0.4V
−10
−2.5
−0.4
−0.2
1.6
−110
−33
µA
µA
Source (Push-pull Mode)
Sink (Push-pull Mode)
mA
mA
mA
mA
µA
0.7
TRI-STATE Leakage
Allowable Sink/Source
Current Per Pin
−2.0
+2.0
D Outputs
15
20
3
mA
mA
mA
mA
L4–L7 (Sink)
All Others
±
Maximum Input Current
without Latchup (Note 5)
RAM Retention Voltage, Vr
Room Temperature
100
500 ns Rise and
Fall Time (Min)
2.0
V
Input Capacitance
7
pF
pF
Load Capacitance on D2
1000
Note 2: Rate of voltage change must be less than 10 V/mS.
Note 3: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 4: The HALT mode will stop CKI from oscillating in the RC and crystal configurations. HALT test conditions: L, and G0..G5 ports configured as outputs and set
high. The D port set to zero. All inputs tied to V . The comparator and the Brown Out circuits are disabled.
CC
Note 5: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than V
and the pins will have sink current
CC
to V when biased at voltages greater than V (the pins do not have source current when biased at a voltage below V ). The effective resistance to V is 750Ω
CC
CC
CC
CC
(typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V.
5
www.national.com
AC Electrical Characteristics
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Conditions
Min
Typ
Max
Units
Instruction Cycle Time (tc)
Crystal/Resonator
R/C Oscillator
4.5V ≤ VCC ≤ 6.0V
2.5V ≤ VCC ≤ 4.5V
4.5V ≤ VCC ≤ 6.0V
COP840CJ
1
2.5
3
DC
DC
DC
DC
DC
DC
µs
µs
µs
µs
µs
µs
µs
2
2.5V ≤ VCC ≤ 4.5V
COP840CJ
7.5
5
VCC Rise Time when Using Brown
Out
VCC = 0V to 6V
50
Frequency at Brown Out Reset
CKI Frequency For Modular Output
CKI Clock Duty Cycle (Note 6)
Rise Time (Note 6)
Fall Time (Note 6)
4
4
MHz
MHz
%
fr = Max
40
60
12
8
fr = 10 MHz ext. Clock
fr = 10 MHz ext. Clock
ns
ns
Inputs
tSetup
4.5V ≤ VCC ≤ 6.0V
2.5V ≤ VCC ≤ 4.5V
4.5V ≤ VCC ≤ 6.0V
2.5V ≤ VCC ≤ 4.5V
RL = 2.2k, CL = 100 pF
200
500
60
ns
ns
ns
ns
tHold
150
Output Propagation Delay
tPD1, tPD0
SO, SK
4.5V ≤ VCC ≤ 6.0V
2.5V ≤ VCC ≤ 4.5V
4.5V ≤ VCC ≤ 6.0V
2.5V ≤ VCC ≤ 4.5V
0.7
1.75
1
µs
µs
µs
µs
All Others
5
Input Pulse Width
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer Input Low Time
MICROWIRE Setup Time (tµWS
1
1
tc
tc
1
tc
1
tc
)
20
56
ns
ns
ns
MICROWIRE Hold Time (tµWH
MICROWIRE Output
)
220
Propagation Delay (tµPD
Reset Pulse Width
)
1.0
µs
Note 6: Parameter characterized but not production tested.
DS011208-2
FIGURE 3. MICROWIRE/PLUS Timing
www.national.com
6
Comparator DC and AC Characteristics
4V ≤ VCC ≤ 6V, −40˚C ≤ TA ≤ + 85˚C (Note 7)
Parameters
Input Offset Voltage
Conditions
Min
Type
Max
Units
mV
V
<
<
±
±
25
0.4V VIN VCC − 1.5V
10
Input Common Mode Voltage Range
Voltage Gain
0.4
VCC − 1.5
300k
V/V
µA
ns
DC Supply Current (when enabled)
Response Time
VCC = 6.0V
250
140
165
300
100 mV Overdrive
500 mV Overdrive
1000 mV Overdrive
60
80
100
125
215
ns
135
ns
Note 7: For comparator output current characteristics see L-Port specs.
Typical Performance Characteristics for COP820CJ
Dynamic—IDD vs VCC
(Crystal Clock Option)
Halt—IDD vs VCC
(Brown Out Disabled)
Halt—IDD vs VCC
(Brown Out Enabled)
DS011208-32
DS011208-33
DS011208-34
Ports L/G Weak
Pull-Up Source Current
Ports L/G Push-Pull
Source Current
Ports L/G Push-Pull
Sink Current
DS011208-35
DS011208-36
DS011208-37
7
www.national.com
Typical Performance Characteristics for COP820CJ (Continued)
Ports L4–L7
Sink Current
Port D Source Current
Port D Sink Current
DS011208-40
DS011208-39
DS011208-38
Brown Out Voltage
vs Temperature
DS011208-41
Typical Performance Characteristics for COP840CJ
Port D Sink current
Halt Current with
Brown Out Disabled
Halt Current with
Brown Out Enabled
DS011208-42
DS011208-43
DS011208-44
www.national.com
8
Typical Performance Characteristics for COP840CJ (Continued)
Halt Current with
Comparator Enabled
Ports L/G Push-Pull
Source Current
Ports L/G Push-Pull
Sink Current
DS011208-45
DS011208-46
DS011208-47
Port D Source Current
Port D Sink Current
DS011208-49
DS011208-48
Brown Out Voltage
vs Temperature
DS011208-50
9
www.national.com
G7 CKO crystal oscillator output (selected by mask option)
or HALT restart input/general purpose input (if clock
option is R/C or external clock)
Pin Description
VCC and GND are the power supply pins.
CKI is the clock input. This can come from an external
source, a R/C generated oscillator or a crystal (in conjunc-
tion with CKO). See Oscillator description.
G6 SI (MICROWIRE serial data input)
G5 SK (MICROWIRE clock I/O)
G4 SO (MICROWIRE serial data output)
G3 TIO (timer/counter input/output)
G0 INTR (an external interrupt)
RESET is the master reset input. See Reset description.
PORT I is a 4-bit Hi-Z input port.
PORT L is an 8-bit I/O port.
Pins G2 and G1 currently do not have any alternate func-
tions.
There are two registers associated with the L port: a data
register and a configuration register. Therefore, each L I/O
bit can be individually configured under software control as
shown below:
The selection of alternate Port G functions are done through
registers PSW [00EF] to enable external interrupt and CN-
TRL1 [00EE] to select TIO and MICROWIRE operations.
Port L
Port L
Port L
Setup
PORT D is a four bit output port that is preset when RESET
goes low. One data memory address location is allocated for
the data register [00DC].
Config.
Data
0
0
1
1
0
1
0
1
Hi-Z Input (TRI-STATE)
Input with Weak Pull-up
Push-pull Zero Output
Push-pull One Output
Note: Care must be exercised with the D2 pin operation. At RESET, the ex-
ternal loads on this pin must ensure that the output voltages stay
above 0.8 V
to prevent the chip from entering special modes. Also
CC
keep the external loading on D2 to less than 1000 pF.
Three data memory address locations are allocated for this
port, one each for data register [00D0], configuration register
[00D1] and the input pins [00D2].
Functional Description
The internal architecture is shown in the block diagram. Data
paths are illustrated in simplified form to depict how the vari-
ous logic elements communicate with each other in imple-
menting the instruction set of the device.
Port L has the following alternate features:
L7 MIWU or MODOUT (high sink current capability)
L6 MIWU (high sink current capability)
L5 MIWU (high sink current capability)
L4 MIWU (high sink current capability)
L3 MIWU
ALU and CPU Registers
The ALU can do an 8-bit addition, subtraction, logical or shift
operations in one cycle time. There are five CPU registers:
A
is the 8-bit Accumulator register
L2 MIWU or CMPIN+
PC is the 15-bit Program Counter register
L1 MIWU or CMPIN−
PU is the upper 7 bits of the program counter (PC)
PL is the lower 8 bits of the program counter (PC)
L0 MIWU or CMPOUT
The selection of alternate Port L functions is done through
registers WKEN [00C9] to enable MIWU and CNTRL2
[00CC] to enable comparator and modulator.
B
X
is the 8-bit address register and can be auto incre-
mented or decremented.
is the 8-bit alternate address register and can be auto
incremented or decremented.
All eight L-pins have Schmitt Triggers on their inputs.
PORT G is an 8-bit port with 6 I/O pins (G0–G5) and 2 input
pins (G6, G7).
SP is the 8-bit stack pointer which points to the subroutine
stack (in RAM).
All eight G-pins have Schmitt Triggers on the inputs.
B, X and SP registers are mapped into the on chip RAM. The
B and X registers are used to address the on chip RAM. The
SP register is used to address the stack in RAM during sub-
routine calls and returns. The SP must be preset by software
upon initialization.
There are two registers associated with the G port: a data
register and a configuration register. Therefore each G port
bit can be individually configured under software control as
shown below:
Port G
Port G
Port G
Setup
Memory
Config.
Data
The memory is separated into two memory spaces: program
and data.
0
0
1
1
0
1
0
1
Hi-Z Input (TRI-STATE)
Input with Weak Pull-up
Push-pull Zero Output
Push-pull One Output
PROGRAM MEMORY
Program memory consists of 1024 x 8 ROM or 2048 x 8
ROM. These bytes of ROM may be instructions or constant
data. The memory is addressed by the 15-bit program
counter (PC). ROM can be indirectly read by the LAID in-
struction for table lookup.
Three data memory address locations are allocated for this
port, one for data register [00D4], one for configuration reg-
ister [00D5] and one for the input pins [00D6]. Since G6 and
G7 are Hi-Z input only pins, any attempt by the user to con-
figure them as outputs by writing a one to the configuration
register will be disregarded. Reading the G6 and G7 configu-
ration bits will return zeros. Note that the device will be
placed in the Halt mode by writing a “1” to the G7 data bit.
DATA MEMORY
The data memory address space includes on chip RAM, I/O
and registers. Data memory is addressed directly by the in-
struction or indirectly through B, X and SP registers. The de-
vice has 64 or 128 bytes of RAM. Sixteen bytes of RAM are
Six pins of Port G have alternate features:
www.national.com
10
If a two pin crystal/resonator oscillator is being used:
Memory (Continued)
RAM Contents
UNCHANGED
mapped as “registers”, these can be loaded immediately,
decremented and tested. Three specific registers: X, B, and
SP are mapped into this space, the other registers are avail-
able for general usage.
Timer T1 and A Contents
WATCHDOG Timer Prescaler/Counter
UNKNOWN
ALTERED
If the external or RC Clock option is being used:
Any bit of data memory can be directly set, reset or tested.
All I/O and registers (except A and PC) are memory mapped;
therefore, I/O bits and register bits can be directly and indi-
vidually set, reset and tested, except the write once only bit
(WDREN, WATCHDOG Reset Enable), and the unused and
read only bits in CNTRL2 and WDREG registers.
RAM Contents
UNCHANGED
Timer T1 and A Contents
WATCHDOG Timer Prescaler/Counter
UNCHANGED
ALTERED
The external RESET takes priority over the Brown Out Re-
set.
Note: RAM contents are undefined upon power-up.
Note: If the RESET pin is pulled low while Brown Out occurs (Brown Out cir-
cuit has detected Brown Out condition), the external reset will not oc-
cur until the Brown Out condition is removed. External reset has prior-
Reset
ity only if V
is greater than the Brown Out voltage.
CC
EXTERNAL RESET
The RESET input pin when pulled low initializes the
micro-controller. The user must insure that the RESET pin is
held low until VCC is within the specified voltage range and
the clock is stabilized. An R/C circuit with a delay 5x greater
than the power supply rise time is recommended (Figure 4).
The device immediately goes into reset state when the RE-
SET input goes low. When the RESET pin goes high the de-
vice comes out of reset state synchronously. The device will
be running within two instruction cycles of the RESET pin go-
ing high. The following actions occur upon reset:
DS011208-51
>
RC 5 x Power Supply Rise Time
FIGURE 4. Recommended Reset Circuit
Port L
TRI-STATE
Port G
TRI-STATE
WATCHDOG RESET
Port D
HIGH
With WATCHDOG enabled, the WATCHDOG logic resets
the device if the user program does not service the WATCH-
DOG timer within the selected service window. The WATCH-
DOG reset does not disable the WATCHDOG. Upon
WATCHDOG reset, the WATCHDOG Prescaler and Counter
are each initialized with FF Hex.
PC
CLEARED
RAM Contents
RANDOM with Power-On-
Reset
UNAFFECTED with external
Reset (power already applied)
Same as RAM
The following actions occur upon WATCHDOG reset that are
different from external reset.
B, X, SP
PSW, CNTRL1,
CNTRL2
WDREN WATCHDOG Reset Enable bit
UNCHANGED
WDUDFWATCHDOG Underflow bitUNCHANGED
and WDREG Reg.
CLEARED
Additional initialization actions that occur as a result of
WATCHDOG reset are as follows:
Multi-Input Wakeup
Reg.
Port L
TRI-STATE
WKEDG, WKEN
WKPND
CLEARED
Port G
TRI-STATE
UNKNOWN
Port D
HIGH
Data and Configuration
Registers for L & G
WATCHDOG Timer
PC
CLEARED
CLEARED
RAM Contents
B, X, SP
UNCHANGED/RANDOM
UNCHANGED
CLEARED
Prescaler/Counter each
loaded with FF
PSW, CNTRL1 and
CNTRL2 (except WDUDF
Bit) Registers
The device comes out of the HALT mode when the RESET
pin is pulled low. In this case, the user has to ensure that the
RESET signal is low long enough to allow the oscillator to re-
start. An internal 256 tc delay is normally used in conjunction
with the two pin crystal oscillator. When the device comes
out of the HALT mode through Multi-Input Wakeup, this de-
lay allows the oscillator to stabilize.
Multi-Input Wakeup
Registers
WKEDG, WKEN
WKPND
CLEARED
UNKNOWN
The following additional actions occur after the device
comes out of the HALT mode through the RESET pin.
Data and Configuration
Registers for L & G
WATCHDOG Timer
CLEARED
Prescalar/Counter
each loaded with FF
11
www.national.com
voltage (Max frequency 4 MHz), For temperature range of
0˚C to 70˚C the Brown Out voltage is expected to be be-
tween 1.9V to 3.9V. The circuit can be enabled or disabled
by Brown Out mask option. If the device is intended to oper-
ate at lower VCC (lower than Brown Out voltage VBO max),
the Brown Out circuit should be disabled by the mask option.
Reset (Continued)
BROWN OUT RESET
The on-board Brown Out protection circuit resets the device
when the operating voltage (VCC) is lower than the Brown
Out voltage. The device is held in reset when VCC stays be-
low the Brown Out Voltage. The device will remain in RESET
as long as VCC is below the Brown Out Voltage. The Device
will resume execution if VCC rises above the Brown Out Volt-
age. If a two pin crystal/resonator clock option is selected,
the Brown Out reset will trigger a 256tc delay. This delay al-
lows the oscillator to stabilize before the device exits the re-
set state. The delay is not used if the clock option is either
R/C or external clock. The contents of data registers and
RAM are unknown following a Brown Out reset. The external
reset takes priority over Brown Out Reset and will deactivate
the 256 tc cycles delay if in progress. The Brown Out reset
takes priority over the WATCHDOG reset.
The Brown Out circuit may be used as a power-up reset pro-
vided the power supply rise time is slower than 50 µs (0V to
6.0V). Brown Out should not be used at frequencies over 4
MHz (COP840CJ).
Note: Brown Out Circuit is active in HALT mode (with the Brown Out mask
option selected).
Oscillator Circuits
EXTERNAL OSCILLATOR
CKI can be driven by an external clock signal provided it
meets the specified duty cycle, rise and fall times, and input
levels. G7/CKO is available as a general purpose input G7
and/or Halt control.
The following actions occur as a result of Brown Out reset:
Port L
TRI-STATE
TRI-STATE
HIGH
CRYSTAL OSCILLATOR
Port G
By selecting G7/CKO as a clock output, CKI and G7/CKO
can be connected to create a crystal controlled oscillator.
Table 1 shows the component values required for various
standard crystal values.
Port D
PC
CLEARED
RANDOM
UNKNOWN
RAM Contents
B, X, SP
R/C OSCILLATOR (COP820CJ)
PSW, CNTRL1, CNTRL2
and WDREG Registers
Multi-Input Wakeup Registers
WKEDG, WKEN
WKPND
For COP820CJ, selecting CKI as a single pin oscillator, CKI
can make a R/C oscillator. G7/CKO is available as a general
purpose input and/or HALT control. Table 2 shows variation
in the oscillator frequencies as functions of the component
(R and C) values.
CLEARED
CLEARED
UNKNOWN
Data and Configuration
Registers for L & G
WATCHDOG Timer
CLEARED
Prescalar/Counter each
loaded with FF
Timer T1 and Accumulator
Unknown data after
coming out of the HALT
(through Brown Out
Reset) with any Clock
option
Note 8: The development system will detect the BROWN OUT RESET ex-
ternally and will force the RESET pin low. The Development System does not
emulate the 256tc delay.
Brown Out Detection
An on-board detection circuit monitors the operating voltage
(VCC) and compares it with the minimum operating voltage
specified. The Brown Out circuit is designed to reset the de-
vice if the operating voltage is below the Brown Out voltage
(between 1.8V to 4.2V at −40˚C to +85˚C). The Minimum op-
erating voltage for the device is 2.5V with Brown Out dis-
abled, but with BROWN OUT enabled the device is guaran-
teed to operate properly down to minimum Brown Out
DS011208-7
FIGURE 5. Clock Oscillator Configurations
TABLE 1. Crystal Oscillator Configuration
R1
(kΩ)
0
R2
(MΩ)
1
C1
(pF)
30
C2
(pF)
CKI Freq.
(MHz)
10
Conditions
30–36
30–36
100–156
VCC = 5V
VCC = 5V
VCC = 5V
0
1
30
4
5.6
1
100/200
0.455
www.national.com
12
Reset (Continued)
TABLE 2. R/C Oscillator Configuration (Part-To-Part Variation)
R
C
CK1 Freq.
(MHz)
Instr. Cycle
(µs)
Conditions
(kΩ)
3.3
5.6
6.8
(pF)
82
2.2 to 2.7
1.1 to 1.3
0.9 to 1.1
3.7 to 4.6
7.4 to 9.0
8.8 to 10.8
VCC = 5V
VCC = 5V
VCC = 5V
100
100
R/C OSCILLATOR (COP840CJ)
a general purpose input G7 and/or Halt control. Adding an
external capacitor will jeopardize the clock frequency toler-
ance and increase EMI emissions. Table 3 shows the clock
frequency for the different resistor values.
For COP840CJ, selecting the R/C oscillator option makes a
R/C oscillator when connecting a resistor from the CKI pin to
V . The capacitor is on-chip. The G7/CKO pin is available as
TABLE 3. RC Oscillator Configuration (Part-To-Part Variation)
CK1 Freq. (MHz) Temperature VCC
R (kΩ)
2.2
±
7.0 15%
-40˚C to +85˚C
-40˚C to +85˚C
-40˚C to +85˚C
4.5V to 5.5V
4.5V to 5.5V
4.5V to 5.5V
±
4.2 10%
4.7
±
7.1 10%
20.0
Note 9: The resistance level is calculated with a total of 5.3 pF capacitance added from the printed circuit board. It is important to take this into account when figuring
the clock frequency.
HALT Mode
The device is a fully static device. The device enters the
HALT mode by writing a one to the G7 bit of the G data reg-
ister. Once in the HALT mode, the internal circuitry does not
receive any clock signal and is therefore frozen in the exact
state it was in when halted. In this mode, the chip will only
draw leakage current (output current and DC current due to
the Brown Out circuit if Brown Out is enabled).
clock option is either RC or External clock, the delay is not
used, but the WATCHDOG Prescaler/Counter contents are
changed. The Development System will not emulate the
256tc delay.
The RESET pin or Brown Out will cause the device to reset
and start executing from address X’0000. A low to high tran-
sition on the G7 pin (if single pin oscillator is used) or
Multi-Input Wakeup will cause the device to start executing
from the address following the HALT instruction.
The device supports four different methods of exiting the
HALT mode. The first method is with a low to high transition
on the CKO (G7) pin. This method precludes the use of the
crystal clock configuration (since CKO is a dedicated out-
put). It may be used either with an RC clock configuration or
an external clock configuration. The second method of exit-
ing the HALT mode is with the multi-Input Wakeup feature on
the L port. The third method of exiting the HALT mode is by
pulling the RESET input low. The fourth method is with the
operating voltage going below Brown Out voltage (if Brown
Out is enabled by mask option).
When RESET pin is used to exit the device from the HALT
mode and the two pin crystal/resonator (CKI/CKO) clock op-
tion is selected, the contents of the Accumulator and the
Timer T1 are undetermined following the reset. All other in-
formation except the WATCHDOG Prescaler/Counter con-
tents is retained until continuing. If the device comes out of
the HALT mode through Brown Out reset, the contents of
data registers and RAM are unknown following the reset. All
information except the WATCHDOG Prescaler/Counter con-
tents is retained if the device exits the HALT mode through
G7 pin or Multi-Input Wakeup.
If the two pin crystal/resonator oscillator is being used and
Multi-Input Wakeup or Brown Out causes the device to exit
the HALT mode, the WAKEUP signal does not allow the chip
to start running immediately since crystal oscillators have a
delayed start up time to reach full amplitude and freuqency
stability. The WATCHDOG timer (consisting of an 8-bit pres-
caler followed by an 8-bit counter) is used to generate a fixed
delay of 256tc to ensure that the oscillator has indeed stabi-
lized before allowing instruction execution. In this case, upon
detecting a valid WAKEUP signal only the oscillator circuitry
is enabled. The WATCHDOG Counter and Prescaler are
each loaded with a value of FF Hex. The WATCHDOG pres-
caler is clocked with the tc instruction cycle. (The tc clock is
derived by dividing the oscillator clock down by a factor of
10). The Schmitt trigger following the CKI inverter on the chip
ensures that the WATCHDOG timer is clocked only when the
oscillator has a sufficiently large amplitude to meet the
Schmitt trigger specs. This Schmitt trigger is not part of the
oscillator closed loop. The start-up timeout from the WATCH-
DOG timer enables the clock signals to be routed to the rest
of the chip. The delay is not activated when the device
comes out of HALT mode through RESET pin. Also, if the
G7 is the HALT-restart pin, but it can still be used as an input.
If the device is not halted, G7 can be used as a general pur-
pose input.
If the Brown Out Enable mask option is selected, the Brown
Out circuit remains active during the HALT mode causing ad-
ditional current to be drawn.
Note: To allow clock resynchronization, it is necessary to program two NOP’s
immediately after the device comes out of the HALT mode. The user
must program two NOP’s following the “enter HALT mode” (set G7
data bit) instruction.
MICROWIRE/PLUS
MICROWIRE/PLUS is a serial synchronous bidirectional
communications interface. The MICROWIRE/PLUS capabil-
ity enables the device to interface with any of National Semi-
conductor’s MICROWIRE peripherals (i.e. A/D converters,
display drivers, EEPROMS, etc.) and with other microcon-
trollers which support the MICROWIRE/PLUS interface. It
consists of an 8-bit serial shift register (SIO) with serial data
13
www.national.com
TABLE 4.
SL0
Reset (Continued)
SL1
0
SK Cycle Time
input (SI), serial data output (SO) and serial shift clock (SK).
Figure 6 shows the block diagram of the MICROWIRE/PLUS
interface.
0
1
x
2tc
4tc
8tc
0
1
where,
is the instruction cycle time.
t
c
MICROWIRE/PLUS OPERATION
Setting the BUSY bit in the PSW register causes the
MICROWIRE/PLUS arrangement to start shifting the data. It
gets reset when eight data bits have been shifted. The user
may reset the BUSY bit by software to allow less than 8 bits
to shift. The device may enter the MICROWIRE/PLUS mode
either as a Master or as a Slave. Figure 7 shows how two de-
vice microcontrollers and several peripherals may be inter-
connected using the MICROWIRE/PLUS arrangement.
DS011208-8
MASTER MICROWIRE/PLUS OPERATION
FIGURE 6. MICROWIRE/PLUS Block Diagram
In the MICROWIRE/PLUS Master mode of operation the
shift clock (SK) is generated internally by the device. The
MICROWIRE/PLUS Master always initiates all data ex-
changes (Figure 7). The MSEL bit in the CNTRL register
must be set to enable the SO and SK functions on the G
Port. The SO and SK pins must also be selected as outputs
by setting appropriate bits in the Port G configuration regis-
ter. Table 5 summarizes the bit settings required for Master
mode of operation.
The shift clock can be selected from either an internal source
or an external source. Operating the MICROWIRE/PLUS in-
terface with the internal clock source is called the Master
mode of operation. Operating the MICROWIRE/PLUS inter-
face with an external shift clock is called the Slave mode of
operation.
The CNTRL register is used to configure and control the
MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS ,
the MSEL bit in the CNTRL register is set to one. The SK
clock rate is selected by the two bits, SL0 and SL1, in the
CNTRL register. Table 4 details the different clock rates that
may be selected.
SLAVE MICROWIRE/PLUS OPERATION
In the MICROWIRE/PLUS Slave mode of operation the SK
clock is generated by an external source. Setting the MSEL
bit in the CNTRL register enables the SO and SK functions
on the G Port. The SK pin must be selected as an input and
the SO pin selected as an output pin by appropriately setting
up the Port G configuration register. Table 5 summarizes the
settings required to enter the Slave mode of operation.
DS011208-23
FIGURE 7. MICROWIRE/PLUS Application
www.national.com
14
MODE 1. TIMER WITH AUTO-LOAD REGISTER
Reset (Continued)
In this mode of operation, the timer T1 counts down at the in-
struction cycle rate. Upon underflow the value in the register
R1 gets automatically reloaded into the timer which contin-
ues to count down. The timer underflow can be programmed
to interrupt the microcontroller. A bit in the control register
CNTRL enables the TIO (G3) pin to toggle upon timer under-
flows. This allows the generation of square-wave outputs or
pulse width modulated outputs under software control
(Figure 8).
The user must set the BUSY flag immediately upon entering
the Slave mode. This will ensure that all data bits sent by the
Master will be shifted properly. After eight clock pulses the
BUSY flag will be cleared and the sequence may be re-
peated. (See Figure 7).
TABLE 5.
G4
G5
G4
G5
G6
Config. Config.
Fun.
Fun. Fun.
Operation
MODE 2. EXTERNAL COUNTER
Bit
Bit
In this mode, the timer T1 becomes a 16-bit external event
counter. The counter counts down upon an edge on the TIO
pin. Control bits in the register CNTRL program the counter
to decrement either on a positive edge or on a negative
edge. Upon underflow the contents of the register R1 are au-
tomatically copied into the counter. The underflow can also
be programmed to generate an interrupt (Figure 9).
1
1
SO
TRI-STATE
SO
Int.
SK
SI
SI
SI
SI
MICROWIRE
Master
0
1
0
1
0
0
Int.
SK
MICROWIRE
Master
Ext.
SK
MICROWIRE
Slave
TRI-STATE
Ext.
SK
MICROWIRE
Slave
Timer/Counter
The device has a powerful 16-bit timer with an associated
16-bit register enabling it to perform extensive timer func-
tions. The timer T1 and its register R1 are each organized as
two 8-bit read/write registers. Control bits in the register CN-
TRL allow the timer to be started and stopped under soft-
ware control. The timer-register pair can be operated in one
of three possible modes. Table 6 details various timer oper-
ating modes and their requisite control settings.
DS011208-24
FIGURE 8. Timer/Counter Auto
Reload Mode Block Diagram
TABLE 6. Timer Operating Modes
CNTRL
Timer
Bits
7 6 5
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Operation Mode
T Interrupt
Counts
On
External Counter w/Auto-Load Reg.
External Counter w/Auto-Load Reg.
Not Allowed
Timer Underflow
Timer Underflow
Not Allowed
TIO Pos. Edge
TIO Neg. Edge
Not Allowed
Not Allowed
Not Allowed
Not Allowed
Timer w/Auto-Load Reg.
Timer w/Auto-Load Reg./Toggle TIO Out
Timer w/Capture Register
Timer w/Capture Register
Timer Underflow
Timer Underflow
TIO Pos. Edge
TIO Neg. Edge
tc
tc
tc
tc
15
www.national.com
Timer/Counter (Continued)
DS011208-29
FIGURE 9. Timer in External Event Counter Mode
MODE 3. TIMER WITH CAPTURE REGISTER
Timer T1 can be used to precisely measure external fre-
quencies or events in this mode of operation. The timer T1
counts down at the instruction cycle rate. Upon the occur-
rence of a specified edge on the TIO pin the contents of the
timer T1 are copied into the register R1. Bits in the control
register CNTRL allow the trigger edge to be specified either
as a positive edge or as a negative edge. In this mode the
user can elect to be interrupted on the specified trigger edge
(Figure 10).
DS011208-26
FIGURE 11. Timer Application
WATCHDOG
The device has an on-board 8-bit WATCHDOG timer. The
timer contains an 8-bit READ/WRITE down counter clocked
by an 8-bit prescaler. Under software control the timer can
be dedicated for the WATCHDOG or used as a general pur-
pose counter. Figure 12 shows the WATCHDOG timer block
diagram.
DS011208-25
FIGURE 10. Timer Capture Mode Block Diagram
MODE 1: WATCHDOG TIMER
TIMER PWM APPLICATION
The WATCHDOG is designed to detect user programs get-
ting stuck in infinite loops resulting in loss of program control
or “runaway” programs. The WATCHDOG can be enabled or
disabled (only once) after the device is reset as a result of
brown out reset or external reset. On power-up the WATCH-
DOG is disabled. The WATCHDOG is enabled by writing a
“1” to WDREN bit (resides in WDREG register). Once en-
abled, the user program should write periodically into the
8-bit counter before the counter underflows. The 8-bit
counter (WDCNT) is memory mapped at address 0CE Hex.
The counter is loaded with n-1 to get n counts. The counter
underflow resets the device, but does not disable the
WATCHDOG. Loading the 8-bit counter initializes the pres-
caler with FF Hex and starts the prescaler/counter. Prescaler
and counter are stopped upon counter underflow. Prescaler
and counter are each loaded with FF Hex when the device
goes into the HALT mode. The prescaler is used for crystal/
resonator start-up when the device exits the HALT mode
through Multi-Input Wakeup. In this case, the prescaler/
counter contents are changed.
Figure 11 shows how a minimal component D/A converter
can be built out of the Timer-Register pair in the Auto-Reload
mode. The timer is placed in the “Timer with auto reload”
mode and the TIO pin is selected as the timer output. At the
outset the TIO pin is set high, the timer T1 holds the on time
and the register R1 holds the signal off time. Setting TRUN
bit starts the timer which counts down at the instruction cycle
rate. The underflow toggles the TIO output and copies the off
time into the timer, which continues to run. By alternately
loading in the on time and the off time at each successive in-
terrupt a PWM frequency can be easily generated.
www.national.com
16
starts the timer. The counter underflow stops the timer. The
WDTEN bit serves as a start bit for the WATCHDOG timer.
This bit is set when the 8-bit counter is loaded by the user
program. The load could be as a result of WATCHDOG ser-
vice (WATCHDOG timer dedicated for WATCHDOG func-
tion) or write to the counter (WATCHDOG timer used as a
general purpose counter). The bit is cleared upon Brown Out
reset, WATCHDOG reset or external reset. The bit is not
memory mapped and is transparent to the user program.
WATCHDOG (Continued)
MODE 2: TIMER
In this mode, the prescaler/counter is used as a timer by
keeping the WDREN (WATCHDOG reset enable) bit at 0.
The counter underflow sets the WDUDF (underflow) bit and
the underflow does not reset the device. Loading the 8-bit
counter (load n-1 for n counts) sets the WDTEN bit (WATCH-
DOG Timer Enable) to “1”, loads the prescaler with FF, and
TABLE 7. WATCHDOG Control/Status
HALT
Mode
WD
EXT/BOR
Counter
Load
Parameter
Reset
Reset
(Note 10)
8-Bit Prescaler
FF
FF
FF
FF
FF
FF
0
FF
8-Bit WD Counter
WDREN Bit
User Value
Unchanged
0
Unchanged
Unchanged
0
No Effect
WDUDF Bit
0
0
1
WDTEN Signal
Unchanged
0
Note 10: BOR is Brown Out Reset.
CONTROL/STATUS BITS
WDREN bit resides in a separate register (bit 0 of WDREG).
This bit enables the WATCHDOG timer to generate a reset.
The bit is cleared upon Brown Out reset, or external reset.
The bit under software control can be written to only once
(once written to, the hardware does not allow the bit to be
changed during program execution).
WDUDF: WATCHDOG Timer Underflow Bit
This bit resides in the CNTRL2 Register. The bit is set when
the WATCHDOG timer underflows. The underflow resets the
device if the WATCHDOG reset enable bit is set (WDREN =
1). Otherwise, WDUDF can be used as the timer underflow
flag. The bit is cleared upon Brown-Out reset, external reset,
load to the 8-bit counter, or going into the HALT mode. It is a
read only bit.
WDREN = 1 WATCHDOG reset is enabled.
WDREN = 0 WATCHDOG reset is disabled.
Table 7 shows the impact of Brown Out Reset, WATCHDOG
Reset, and External Reset on the Control/Status bits.
WDREN: WD Reset Enable
17
www.national.com
WATCHDOG (Continued)
DS011208-15
FIGURE 12. WATCHDOG Timer Block Diagram
Modulator/Timer
The Modulator/Timer contains an 8-bit counter and an 8-bit
autoreload register (MODRL address 0CF Hex). The
Modulator/Timer has two modes of operation, selected by
the control bit MC3. The Modulator/Timer Control bits MC1,
MC2 and MC3 reside in CNTRL2 Register.
low time. Unless the number of counts is changed, the user
program does not have to load the counter each time the
counter is started. The counter can simply be started by set-
ting the MC1 bit. Setting MC1 by software will load the
counter with the value of the autoreload register. The soft-
ware can reset MC1 to stop the counter.
MODE 1: MODULATOR
MODE 2: PWM TIMER
The Modulator is used to generate high frequency pulses on
the modulator output pin (L7). The L7 pin should be config-
ured as an output. The number of pulses is determined by
the 8-bit down counter. Under software control the modulator
input clock can be either CKI or tC. The tc clock is derived by
dividing down the oscillator clock by a factor of 10. Three
control bits (MC1, MC2, and MC3) are used for the
Modulator/Timer output control. When MC2 = 1 and MC3 =
1, CKI is used as the modulator input clock. When MC2 = 0,
and MC3 = 1, tc is used as the modulator input clock. The
user loads the counter with the desired number of counts
(256 max) and sets MC1 to start the counter. The modulator
autoreload register is loaded with n-1 to get n pulses. CKI or
tc pulses are routed to the modulator output (L7) until the
counter underflows (Figure 13). Upon underflow the hard-
ware resets MC1 and stops the counter. The L7 pin goes low
and stays low until the counter is restarted by the user pro-
gram. The user program has the responsibility to timeout the
The counter can also be used as a PWM Timer. In this mode,
an 8-bit register is used to serve as an autoreload register
(MODRL).
a. 50% Duty Cycle:
When MC1 is 1 and MC2, MC3 are 0, a 50% duty cycle free
running signal is generated on the L7 output pin (Figure 14).
The L7 pin must be configured as an output pin. In this mode
the 8-bit counter is clocked by tC. Setting the MC1 control bit
by software loads the counter with the value of the autore-
load register and starts the counter. The counter underflow
toggles the (L7) output pin. The 50% duty cycle signal will be
continuously generated until MC1 is reset by the user pro-
gram.
www.national.com
18
TABLE 8. Modulator/Timer Modes
Modulator/Timer (Continued)
Control Bits in
Operation Mode
L7 Function
b. Variable Duty Cycle:
CNTRL2(00CC)
When MC3 = 0 and MC2 = 1, a variable duty cycle PWM sig-
nal is generated on the L7 output pin. The counter is clocked
by tC. In this mode the 16-bit timer T1 along with the 8-bit
down counter are used to generate a variable duty cycle
PWM signal. The timer T1 underflow sets MC1 which starts
the down counter and it also sets L7 high (L7 should be con-
figured as an output).When the counter underflows the MC1
control bit is reset and the L7 output will go low until the next
timer T1 underflow. Therefore, the width of the output pulse
is controlled by the 8-bit counter and the pulse duration is
controlled by the 16-bit timer T1 (Figure 15). Timer T1 must
be configured in “PWM Mode/Toggle TIO Out” (CNTRL1 Bits
7,6,5 = 101).
MC3 MC2 MC1
0
0
0
0
0
1
Normal I/O
50% Duty Cycle Mode (Clocked by
tc)
0
1
X
Variable Duty Cycle Mode (Clocked
by tc) Using Timer 1 Underflow
1
1
0
1
X
X
Modulator Mode (Clocked by tc)
Modulator Mode (Clocked by CKI)
Note 11: MC1, MC2 and MC3 control bits are cleared upon reset.
Table
8 shows the different operation modes for the
Modulator/Timer.
Internal Data Bus
DS011208-16
FIGURE 13. Mode 1: Modulator Block Diagram/Output Waveform
DS011208-17
19
www.national.com
Modulator/Timer (Continued)
DS011208-18
FIGURE 14. Mode 2a: 50% Duty Cycle Output
DS011208-19
DS011208-20
FIGURE 15. Mode 2b: Variable Duty Cycle Output
(CMPEN = 1, CMPOE=X)
Comparator
CMPOE Enables comparator output to pin L0
The device has one differential comparator. Ports L0–L2 are
used for the comparator. The output of the comparator is
brought out to a pin. Port L has the following assignments:
(“1”=enable), CMPEN bit must be set to enable
this function. If CMPEN=0, L0 will be 0.
The Comparator Select/Control bits are cleared on RESET
(the comparator is disabled). To save power the program
should also disable the comparator before the device enters
the HALT mode.
L0 Comparator output
L1 Comparator negative input
L2 Comparator positive input
The user program must set up L0, L1 and L2 ports correctly
for comparator Inputs/Output: L1 and L2 need to be config-
ured as inputs and L0 as output. See Table 9.
THE COMPARATOR STATUS/CONTROL BITS
These bits reside in the CNTRL2 Register (Address 0CC)
CMPEN Enables comparator (“1” = enable)
CMPRD Reads comparator output internally
TABLE 9. Comparator DC and AC Characteristics
4V ≤ VCC ≤ 6V, −40˚C ≤ TA ≤ + 85˚C (Note 7)
Parameters
Conditions
Min
Type
Max
Units
mV
V
<
<
±
±
25
Input Offset Voltage
0.4V VIN VCC − 1.5V
10
Input Common Mode Voltage Range
Voltage Gain
0.4
VCC − 1.5
300k
V/V
µA
ns
DC Supply Current (when enabled)
Response Time
VCC = 6.0V
250
140
165
300
100 mV Overdrive
500 mV Overdrive
1000 mV Overdrive
60
80
100
125
215
ns
135
ns
Note 12: For comparator output current characteristics see L-Port specs.
www.national.com
20
prescaler generates a fixed delay to ensure that the oscil-
lator has indeed stabilized before allowing the device to
execute instructions. In this case, upon detecting a valid
Wakeup signal only the oscillator circuitry and the
WATCHDOG timer are enabled. The WATCHDOG timer
prescaler is loaded with a value of FF Hex (256 counts)
and is clocked from the tc instruction cycle clock. The tc
clock is derived by dividing down the oscillator clock by a
factor of 10. A Schmitt trigger following the CKI on chip in-
verter ensures that the WATCHDOG timer is clocked only
when the oscillator has a sufficiently large amplitude to
meet the Schmitt trigger specs. This Schmitt trigger is not
part of the oscillator closed loop. The startup timeout from
the WATCHDOG timer enables the clock signals to be
routed to the rest of the chip.
Multi-Input Wake Up
The Multi-Input Wakeup feature is used to return
(wakeup) the device from the HALT mode. Figure 16
shows the Multi-Input Wakeup logic.
This feature utilizes the L Port. The user selects which
particular L port bit or combination of L Port bits will cause
the device to exit the HALT mode. Three 8-bit memory
mapped registers, Reg:WKEN, Reg:WKEDG, and Reg-
:WKPND are used in conjunction with the L port to imple-
ment the Multi-Input Wakeup feature.
All three registers Reg:WKEN, Reg:WKPND, and
Reg:WKEDG are read/write registers, and are cleared at
reset, except WKPND. WKPND is unknown on reset.
The user can select whether the trigger condition on the
selected L Port pin is going to be either a positive edge
(low to high transition) or a negative edge (high to low
transition). This selection is made via the Reg:WKEDG,
which is an 8-bit control register with a bit assigned to
each L Port pin. Setting the control bit will select the trig-
ger condition to be a negative edge on that particular L
Port pin. Resetting the bit selects the trigger condition to
be a positive edge. Changing an edge select entails sev-
eral steps in order to avoid a pseudo Wakeup condition as
a result of the edge change. First, the associated WKEN
bit should be reset, followed by the edge select change in
WKEDG. Next, the associated WKPND bit should be
cleared, followed by the associated WKEN bit being
re-enabled.
An example may serve to clarify this procedure. Suppose
we wish to change the edge select from positive (low go-
ing high) to negative (high going low) for L port bit 5,
where bit 5 has previously been enabled for an input. The
program would be as follows:
RBIT 5, WKEN ; Disable MIWU
DS011208-21
SBIT 5, WKEDG ; Change edge polarity
RBIT 5, WKPND ; Reset pending flag
SBIT 5, WKEN ; Enable MIWU
FIGURE 16. Multi-Input Wakeup Logic
INTERRUPTS
If the L port bits have been used as outputs and then
changed to inputs with Multi-Input Wakeup, a safety pro-
cedure should also be followed to avoid inherited pseudo
wakeup conditions. After the selected L port bits have
been changed from output to input but before the associ-
ated WKEN bits are enabled, the associated edge select
bits in WKEDG should be set or reset for the desired edge
selects, followed by the associated WKPND bits being
cleared. This same procedure should be used following
RESET, since the L port inputs are left floating as a result
of RESET.
The device has a sophisticated interrupt structure to allow
easy interface to the real world. There are three possible
interrupt sources, as shown below.
— A maskable interrupt on external G0 input (positive or
negative edge sensitive under software control)
— A maskable interrupt on timer carry or timer capture
— A non-maskable software/error interrupt on opcode
zero
INTERRUPT CONTROL
The occurrence of the selected trigger condition for
Multi-Input Wakeup is latched into a pending register
called Reg:WKPND. The respective bits of the WKPND
register will be set on the occurrence of the selected trig-
ger edge on the corresponding Port L pin. The user has
the responsibility of clearing these pending flags. Since
the Reg:WKPND is a pending register for the occurrence
of selected wakeup conditions, the device will not enter
the HALT mode if any Wakeup bit is both enabled and
pending. Setting the G7 data bit under this condition will
not allow the device to enter the HALT mode. Conse-
quently, the user has the responsibility of clearing the
pending flags before attempting to enter the HALT mode.
The GIE (global interrupt enable) bit enables the interrupt
function. This is used in conjunction with ENI and ENTI to
select one or both of the interrupt sources. This bit is reset
when interrupt is acknowledged.
ENI and ENTI bits select external and timer interrupts re-
spectively. Thus the user can select either or both sources
to interrupt the microcontroller when GIE is enabled.
IEDG selects the external interrupt edge (0 = rising edge,
1 = falling edge). The user can get an interrupt on both ris-
ing and falling edges by toggling the state of IEDG bit after
each interrupt.
IPND and TPND bits signal which interrupt is pending. Af-
ter an interrupt is acknowledged, the user can check these
two bits to determine which interrupt is pending. This per-
mits the interrupts to be prioritized under software. The
If a crystal oscillator is being used, the Wakeup signal will
not start the chip running immediately since crystal oscil-
lators have a finite start up time. The WATCHDOG timer
21
www.national.com
Note: There is always the possibility of an interrupt occurring during an in-
struction which is attempting to reset the GIE bit or any other inter-
rupt enable bit. If this occurs when a single cycle instruction is being
used to reset the interrupt enable bit, the interrupt enable bit will be
reset but an interrupt may still occur. This is because interrupt pro-
cessing is started at the same time as the interrupt bit is being re-
set. To avoid this scenario, the user should always use a two, three,
or four cycle instruction to reset interrupt enable bits.
Multi-Input Wake Up (Continued)
pending flags have to be cleared by the user. Setting the
GIE bit high inside the interrupt subroutine allows nested
interrupts.
The software interrupt does not reset the GIE bit. This
means that the controller can be interrupted by other inter-
rupt sources while servicing the software interrupt.
DETECTION OF ILLEGAL CONDITIONS
The device incorporates a hardware mechanism that allows
it to detect illegal conditions which may occur from coding er-
rors, noise, and “brown out” voltage drop situations. Specifi-
cally, it detects cases of executing out of undefined ROM
area and unbalanced tack situations.
INTERRUPT PROCESSING
The interrupt, once acknowledged, pushes the program
counter (PC) onto the stack and the stack pointer (SP) is
decremented twice. The Global Interrupt Enable (GIE) bit
is reset to disable further interrupts. The microcontroller
then vectors to the address 00FFH and resumes execu-
tion from that address. This process takes 7 cycles to
complete. At the end of the interrupt subroutine, any of the
following three instructions return the processor back to
the main program: RET, RETSK or RETI. Either one of the
three instructions will pop the stack into the program
counter (PC). The stack pointer is then incremented twice.
The RETI instruction additionally sets the GIE bit to
re-enable further interrupts.
Reading an undefined ROM location returns 00 (hexadeci-
mal) as its contents. The opcode for a software interrupt is
also “00”. Thus a program accessing undefined ROM will
cause a software interrupt.
Reading an undefined RAM location returns an FF (hexa-
decimal). The subroutine stack on the device grows down for
each subroutine call. By initializing the stack pointer to the
top of RAM, the first unbalanced return instruction will cause
the stack pointer to address undefined RAM. As a result the
program will attempt to execute from FFFF (hexadecimal),
which is an undefined ROM location and will trigger a soft-
ware interrupt.
Any of the three instructions can be used to return from a
hardware interrupt subroutine. The RETSK instruction
should be used when returning from a software interrupt
subroutine to avoid entering an infinite loop.
DS011208-27
FIGURE 17. Interrupt Block Diagram
www.national.com
22
Control Registers
CNTRL1 REGISTER (ADDRESS 00EE)
CNTRL2 REGISTER (ADDRESS 00CC)
MC3 MC2 MC1 CMPEN CMPRD CMPOE WDUDF unused
TC3 TC2 TC1 TRUN MSEL IEDG SL1
Bit 7
SL0
R/W R/W R/W
Bit 7
R/W
R/O
R/W
R/O
Bit 0
Bit 0
The Timer and MICROWIRE control register contains the fol-
lowing bits:
MC3
MC2
MC1
Modulator/Timer Control Bit
Modulator/Timer Control Bit
Modulator/Timer Control Bit
TC3
Timer T1 Mode Control Bit
Timer T1 Mode Control Bit
Timer T1 Mode Control Bit
Used to start and stop the timer/counter
(1 = run, 0 = stop)
TC2
CMPEN Comparator Enable Bit
CMPRD Comparator Read Bit
TC1
TRUN
CMPOE Comparator Output Enable Bit
WDUDF WATCHDOG Timer Underflow Bit (Read Only)
MSEL
IEDG
Selects G5 and G4 as MICROWIRE signals
SK and SO respectively
WDREG REGISTER (ADDRESS 00CD)
External interrupt edge polarity select
SL1 and SL0 Select the MICROWIRE clock divide-by
(00 = 2, 01 = 4, 1x = 8)
UNUSED
WDREN
Bit 7
Bit 0
WDREN WATCHDOG Reset Enable Bit (Write Once Only)
PSW REGISTER (ADDRESS 00EF)
HC
C
TPND ENTI IPND BUSY ENI
GIE
Bit 7
Bit 0
The PSW register contains the following select bits:
HC
C
Half-Carry Flip/Flop
Carry Flip/Flop
TPND Timer T1 interrupt pending
(timer Underflow or capture edge)
ENTI Timer T1 interrupt enable
IPND External interrupt pending
BUSY MICROWIRE busy shifting flag
ENI
GIE
External interrupt enable
Global interrupt enable (enables interrupts)
The Half-Carry bit is also effected by all the instructions that
effect the Carry flag. The flag values depend upon the in-
struction. For example, after executing the ADC instruction
the values of the Carry and the Half-Carry flag depend upon
the operands involved. However, instructions like SET C and
RESET C will set and clear both the carry flags. Table 10 lists
the instructions that effect the HC and the C flags.
TABLE 10. Instructions Effecting HC and C Flags
Instr.
ADC
HC Flag
C Flag
Depends on
Operands
Depends on
Operands
SUBC
Depends on
Operands
Depends on
Operands
SET C
RESET C
RRC
Set
Set
Set
Set
Depends on
Operands
Depends on
Operands
23
www.national.com
Memory Map
All RAM, ports and registers (except A and PC) are mapped
into data memory address space.
Addressing Modes
There are ten addressing modes, six for operand addressing
and four for transfer of control.
Address
Contents
OPERAND ADDRESSING MODES
00 to 2F
(820CJ)
On-chip RAM bytes (48 bytes)
REGISTER INDIRECT
This is the “normal” addressing mode for the chip. The oper-
00 to 6F
(840CJ)
On-chip RAM bytes (112 bytes)
and is the data memory addressed by the B or X pointer.
REGISTER INDIRECT WITH AUTO POST INCREMENT
OR DECREMENT
30 to 7F
(820CJ)
Unused RAM Address Space (Reads as All
Ones)
This addressing mode is used with the LD and X instruc-
tions. The operand is the data memory addressed by the B
or X pointer. This is a register indirect mode that automati-
cally post increments or post decrements the B or X pointer
after executing the instruction.
70 to 7F
(840CJ)
Unused RAM Address Space (Reads as All
Ones)
80 to BF
Expansion Space for On-Chip EERAM
(Reads Undefined Data)
DIRECT
C0 to C7
C8
Reserved
The instruction contains an 8-bit address field that directly
points to the data memory for the operand.
MIWU Edge Select Register (Reg:WKEDG)
MIWU Enable Register (Reg:WKEN)
MIWU Pending Register (Reg:WKPND)
Reserved
C9
IMMEDIATE
CA
The instruction contains an 8-bit immediate field as the oper-
and.
CB
SHORT IMMEDIATE
CC
Control2 Register (CNTRL2)
WATCHDOG Register (WDREG)
WATCHDOG Counter (WDCNT)
Modulator Reload (MODRL)
Port L Data Register
This addressing mode issued with the LD B,# instruction,
where the immediate is less than 16. The instruction con-
tains a 4-bit immediate field as the operand.
CD
#
CE
CF
INDIRECT
D0
This addressing mode is used with the LAID instruction. The
contents of the accumulator are used as a partial address
(lower 8 bits of PC) for accessing a data operand from the
program memory.
D1
Port L Configuration Register
Port L Input Pins (Read Only)
Reserved for Port L
D2
D3
TRANSFER OF CONTROL ADDRESSING MODES
D4
Port G Data Register
RELATIVE
D5
Port G Configuration Register
Port G Input Pins (Read Only)
Port I Input Pins (Read Only)
Reserved for Port C
This mode is used for the JP instruction with the instruction
field being added to the program counter to produce the next
instruction address. JP has a range from −31 to +32 to allow
a one byte relative jump (JP + 1 is implemented by a NOP in-
struction). There are no “blocks” or “pages” when using JP
since all 15 bits of the PC are used.
D6
D7
D8 to DB
DC
Port D Data Register
DD to DF
E0 to EF
E0 to E7
E8
Reserved for Port D
ABSOLUTE
On-Chip Functions and Registers
Reserved for Future Parts
Reserved
This mode is used with the JMP and JSR instructions with
the instruction field of 12 bits replacing the lower 12 bits of
the program counter (PC). This allows jumping to any loca-
tion in the current 4k program memory segment.
E9
MICROWIRE Shift Register
Timer Lower Byte
ABSOLUTE LONG
EA
This mode is used with the JMPL and JSRL instructions with
the instruction field of 15 bits replacing the entire 15 bits of
the program counter (PC). This allows jumping to any loca-
tion in the entire 32k program memory space.
EB
Timer Upper Byte
EC
Timer1 Autoreload Register Lower Byte
Timer1 Autoreload Register Upper Byte
CNTRL1 Control Register
PSW Register
ED
EE
INDIRECT
EF
This mode is used with the JID instruction. The contents of
the accumulator are used as a partial address (lower 8 bits of
PC) for accessing a location in the program memory. The
contents of this program memory location serves as a partial
address (lower 8 bits of PC) for the jump to the next instruc-
tion.
F0 to FF
FC
On-Chip RAM Mapped as Registers
X Register
FD
SP Register
FE
B Register
Reading other unused memory locations will return unde-
fined data.
www.national.com
24
Instruction Set
REGISTER AND SYMBOL DEFINITIONS
Symbols
[B]
[X]
Memory indirectly addressed by B register
Memory indirectly addressed by X register
Registers
A
B
X
8-bit Accumulator register
8-bit Address register
8-bit Address register
Mem Direct address memory or [B]
MemI Direct address memory or [B] or Immediate data
Imm 8-bit Immediate data
SP 8-bit Stack pointer register
PC 15-bit Program counter register
PU upper 7 bits of PC
Reg
Register memory: addresses F0 to FF (Includes B, X
and SP)
Bit
←
↔
Bit number (0 to 7)
Loaded with
PL lower 8 bits of PC
C
1-bit of PSW register for carry
Exchanged with
HC Half Carry
GIE 1-bit of PSW register for global interrupt enable
INSTRUCTION SET
←
←
ADD
ADC
add
A
A
A + MemI
A + MemI + C, C
←
add with carry
Carry
Carry
←
HC
Half Carry
←
←
SUBC
subtract with carry
A
A + MemI +C, C
←
HC
Half Carry
A and MemI
A or MemI
←
AND
OR
Logical AND
A
A
A
←
←
Logical OR
XOR
IFEQ
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
X
Logical Exclusive-OR
IF equal
A xor MemI
Compare A and MemI, Do next if A = MemI
>
Compare A and MemI, Do next if A MemI
≠
Do next if lower 4 bits of B Imm
IF greater than
IF B not equal
←
Reg − 1, skip if Reg goes to 0
Decrement Reg. ,skip if zero
Set bit
Reg
1 to bit, Mem (bit= 0 to 7 immediate)
0 to bit, Mem
Reset bit
If bit
If bit, Mem is true, do next instr.
↔
←
Exchange A with memory
Load A with memory
Load Direct memory Immed.
Load Register memory Immed.
Exchange A with memory [B]
Exchange A with memory [X]
Load A with memory [B]
Load A with memory [X]
Load Memory Immediate
Clear A
A
A
Mem
LD A
LD mem
LD Reg
X
MemI
←
Mem
Reg
Imm
←
Imm
↔
←
←
←
←
±
B 1)
A
[B]
[X]
[B]
[X]
(B
(X
(B
(X
↔
±
X 1)
X
A
←
±
B 1)
LD A
LD A
LD M
CLRA
INCA
DECA
LAID
DCORA
RRCA
SWAPA
SC
A
←
±
X 1)
A
←
←
B 1)
±
[B]
Imm (B
←
A
A
A
A
A
C
0
←
←
←
←
→
Increment A
A + 1
A − 1
Decrement A
Load A indirect from ROM
DECIMAL CORRECT A
ROTATE A RIGHT THRU C
Swap nibbles of A
Set C
ROM(PU,A)
BCD correction (follows ADC, SUBC)
→
→
→
C
A7
…
A0
↔
A7 … A4
A3 … A0
←
←
←
C
C
1, HC
1
0
←
0, HC
RC
Reset C
IFC
If C
If C is true, do next instruction
IFNC
JMPL
If not C
If C is not true, do next instruction
←
ii (ii = 15 bits, 0 to 32k)
Jump absolute long
PC
25
www.national.com
Instruction Set (Continued)
INSTRUCTION SET (Continued)
←
JMP
JP
Jump absolute
PC11..0
i (i = 12 bits)
←
PC
Jump relative short
Jump subroutine long
Jump subroutine
Jump indirect
PC + r (r is −31 to +32, not 1)
←
←
←
←
←
ii
JSRL
JSR
[SP]
[SP]
PL,[SP-1]
PL,[SP-1]
PU,SP-2,PC
←
PU,SP-2,PC11.. 0
i
←
ROM(PU,A)
JID
PL
←
←
←
←
RET
RETSK
RETI
INTR
NOP
Return from subroutine
Return and Skip
SP+2,PL
SP+2,PL
SP+2,PL
[SP],PU
[SP],PU
[SP],PU
[SP-1]
[SP-1],Skip next instruction
←
←
←
Return from Interrupt
Generate an interrupt
No operation
[SP-1],GIE
1
←
←
←
PU,SP-2,PC 0FF
[SP]
PL,[SP−1]
←
PC
PC + 1
www.national.com
26
Instruction Set (Continued)
0 – 3
B i t s
27
www.national.com
Instructions Using A & C
Instruction Execution Time
Instructions
CLRA
INCA
Bytes/Cycles
Most instructions are single byte (with immediate addressing
mode instruction taking two bytes).
1/1
1/1
1/1
1/3
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Most single instructions take one cycle time to execute.
Skipped instructions require x number of cycles to be
skipped, where x equals the number of bytes in the skipped
instruction opcode.
DECA
LAID
DCOR
RRCA
SWAPA
SC
See the BYTES and CYCLES per INSTRUCTION table for
details.
Bytes and Cycles per
Instruction
RC
The following table shows the number of bytes and cycles for
each instruction in the format of byte/cycle.
IFC
IFNC
Arithmetic Instructions (Bytes/Cycles)
Transfer of Control Instructions
Instructions Bytes/Cycles
JMPL
[B]
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Direct
3/4
Immed.
2/2
ADD
ADC
SUBC
AND
OR
3/4
2/2
3/4
2/3
1/3
3/5
2/5
1/3
1/5
1/5
1/5
1/7
1/1
3/4
2/2
JMP
JP
3/4
2/2
3/4
2/2
JSRL
JSR
XOR
IFEQ
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
3/4
2/2
3/4
2/2
JID
3/4
2/2
RET
RETSK
RETI
INTR
NOP
1/3
3/4
3/4
3/4
1/1
1/1
1/1
Memory Transfer Instructions (Bytes/Cycles)
Register
Register Indirect
Auto Incr & Decr
Indirect Direct Immed.
[B] [X]
1/1 1/3
1/1 1/3
[B+, B−]
1/2
[X+, X−]
1/3
*
X A,
2/3
2/3
*
LD A,
2/2
1/1
2/3
1/2
1/3
<
(If B 16)
LD B,Imm
LD B,Imm
>
(If B 15)
LD
3/3
2/2
Mem,Imm
LD
2/3
Reg,Imm
>
*
=
Memory location addressed by B or X or directly.
The following table shows the instructions assigned to un-
used opcodes. This table is for information only. The opera-
tions performed are subject to change without notice. Do not
use these opcodes.
Unused
Opcode
67
Instruction
Unused
Instruction
Opcode
B5
NOP
RET
NOP
X A, [X]
NOP
8C
B7
Unused
Opcode
60
Instruction
Unused
Opcode
A9
Instruction
99
NOP
B9
9F
LD [B], #i
X A, [B]
NOP
BF
LD A, [X]
NOP
NOP
NOP
NOP
NOP
A7
61
AF
LD A, [B]
A8
→
62
B1
C
HC
63
B4
NOP
www.national.com
28
Mask Options
Development Tools Support
The mask programmable options are listed below. The op-
tions are programmed at the same time as the ROM pattern
to provide the user with hardware flexibility to a variety of os-
cillation and packaging configuration.
OVERVIEW
National is engaged with an international community of inde-
pendent 3rd party vendors who provide hardware and soft-
ware development tool support. Through National’s interac-
tion and guidance, these tools cooperate to form a choice of
solutions that fits each developer’s needs.
OPTION 1: CKI INPUT
= 1 Crystal (CKI/IO) CKO for crystal configuration
= 2 External (CKI/IO) CKO available as G7 input
= 3 R/C (CKI/IO) CKO available as G7 input
This section provides a summary of the tool and develop-
ment kits currently available. Up-to-date information, selec-
tion guides, free tools, demos, updates, and purchase infor-
mation can be obtained at our web site at:
www.national.com/cop8.
OPTION 2: BROWN OUT
= 1 Enable Brown Out Detection
= 2 Disable Brown Out Detection
SUMMARY OF TOOLS
COP8 Evaluation Tools
OPTION 3: BONDING
•
COP8–NSEVAL: Free Software Evaluation package for
Windows. A fully integrated evaluation environment for
COP8, including versions of WCOP8 IDE (Integrated De-
velopment Environment), COP8-NSASM, COP8-MLSIM,
COP820CJ
= 1 28-pin DIP
= 2 20-pin DIP/SO
= 3 16-pin SO
= 4 28-pin SO
COP840CJ
28-pin DIP/SO
20-pin DIP/SO
™
COP8C, DriveWay COP8, Manuals, and other COP8
information.
N/A
N/A
•
•
COP8–MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
COP8–EPU: Very Low cost COP8 Evaluation & Pro-
gramming Unit. Windows based evaluation and
hardware-simulation tool, with COP8 device programmer
and erasable samples. Includes COP8-NSDEV, Drive-
way COP8 Demo, MetaLink Debugger, I/O cables and
power supply.
•
•
COP8–EVAL-ICUxx: Very Low cost evaluation and de-
sign test board for COP8ACC and COP8SGx Families,
from ICU. Real-time environment with add-on A/D, D/A,
and EEPROM. Includes software routines and reference
designs.
Manuals, Applications Notes, Literature: Available free
from our web site at: www.national.com/cop8.
COP8 Integrated Software/Hardware Design Develop-
ment Kits
•
COP8-EPU: Very Low cost Evaluation & Programming
Unit. Windows based development and hardware-
simulation tool for COPSx/xG families, with COP8 device
programmer and samples. Includes COP8-NSDEV,
Driveway COP8 Demo, MetaLink Debugger, cables and
power supply.
•
COP8-DM: Moderate cost Debug Module from MetaLink.
A Windows based, real-time in-circuit emulation tool with
COP8 device programmer. Includes COP8-NSDEV,
DriveWay COP8 Demo, MetaLink Debugger, power sup-
ply, emulation cables and adapters.
COP8 Development Languages and Environments
•
COP8-NSASM: Free COP8 Assembler v5 for Win32.
Macro assembler, linker, and librarian for COP8 software
development. Supports all COP8 devices. (DOS/Win16
v4.10.2 available with limited support). (Compatible with
WCOP8 IDE, COP8C, and DriveWay COP8).
•
COP8-NSDEV: Very low cost Software Development
Package for Windows. An integrated development envi-
ronment for COP8, including WCOP8 IDE, COP8-
NSASM, COP8-MLSIM.
29
www.national.com
COP8 Productivity Enhancement Tools
Development Tools Support
•
WCOP8 IDE: Very Low cost IDE (Integrated Develop-
ment Environment) from KKD. Supports COP8C, COP8-
NSASM, COP8-MLSIM, DriveWay COP8, and MetaLink
debugger under a common Windows Project Manage-
ment environment. Code development, debug, and emu-
lation tools can be launched from the project window
framework.
(Continued)
•
COP8C: Moderately priced C Cross-Compiler and Code
Development System from Byte Craft (no code limit). In-
cludes BCLIDE (Byte Craft Limited Integrated Develop-
ment Environment) for Win32, editor, optimizing C Cross-
Compiler, macro cross assembler, BC-Linker, and
MetaLink tools support. (DOS/SUN versions available;
Compiler is installable under WCOP8 IDE; Compatible
with DriveWay COP8).
•
DriveWay-COP8: Low cost COP8 Peripherals Code
Generation tool from Aisys Corporation. Automatically
generates tested and documented C or Assembly source
code modules containing I/O drivers and interrupt han-
dlers for each on-chip peripheral. Application specific
code can be inserted for customization using the inte-
grated editor. (Compatible with COP8-NSASM, COP8C,
and WCOP8 IDE.)
•
•
EWCOP8-KS: Very Low cost ANSI C-Compiler and Em-
bedded Workbench from IAR (Kickstart version:
COP8Sx/Fx only with 2k code limit; No FP). A fully inte-
grated Win32 IDE, ANSI C-Compiler, macro assembler,
editor, linker, Liberian, C-Spy simulator/debugger, PLUS
MetaLink EPU/DM emulator support.
•
•
COP8-UTILS: Free set of COP8 assembly code ex-
amples, device drivers, and utilities to speed up code de-
velopment.
EWCOP8-AS: Moderately priced COP8 Assembler and
Embedded Workbench from IAR (no code limit). A fully in-
tegrated Win32 IDE, macro assembler, editor, linker, li-
brarian, and C-Spy high-level simulator/debugger with
I/O and interrupts support. (Upgradeable with optional
C-Compiler and/or MetaLink Debugger/Emulator sup-
port).
COP8-MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
COP8 Real-Time Emulation Tools
•
COP8-DM: MetaLink Debug Module. A moderately
•
EWCOP8-BL: Moderately priced ANSI C-Compiler and
Embedded Workbench from IAR (Baseline version: All
COP8 devices; 4k code limit; no FP). A fully integrated
Win32 IDE, ANSI C-Compiler, macro assembler, editor,
linker, librarian, and C-Spy high-level simulator/debugger.
(Upgradeable; CWCOP8-M MetaLink tools interface sup-
port optional).
priced real-time in-circuit emulation tool, with COP8 de-
vice programmer. Includes COP8-NSDEV, DriveWay
COP8 Demo, MetaLink Debugger, power supply, emula-
tion cables and adapters.
•
IM-COP8: MetaLink iceMASTER®. A full featured, real-
time in-circuit emulator for COP8 devices. Includes Met-
aLink Windows Debugger, and power supply. Package-
specific probes and surface mount adaptors are ordered
separately.
•
•
EWCOP8: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, and C-Spy high-level
simulator/debugger. (CWCOP8-M MetaLink tools inter-
face support optional).
COP8 Device Programmer Support
•
MetaLink’s EPU and Debug Module include development
device programming capability for COP8 devices.
EWCOP8-M: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, C-Spy high-level
simulator/debugger, PLUS MetaLink debugger/hardware
interface (CWCOP8-M).
•
Third-party programmers and automatic handling equip-
ment cover needs from engineering prototype and pilot
production, to full production environments.
•
Factory programming available for high-volume require-
ments.
www.national.com
30
Development Tools Support (Continued)
TOOLS ORDERING NUMBERS FOR THE COP820CJ/COP840CJ FAMILY DEVICES
Vendor
Tools
Order Number
COP8-NSEVAL
Cost
Notes
National COP8-NSEVAL
COP8-NSASM
COP8-MLSIM
COP8-NSDEV
COP8-EPU
Free Web site download
COP8-NSASM
Free Included in EPU and DM. Web site download
Free Included in EPU and DM. Web site download
COP8-MLSIM
COP8-NSDEV
VL
Included in EPU and DM. Order CD from website
Not available for this device
Contact MetaLink
COP8-DM
Development
Devices
COP87L20/40CJxx
COP87L22/42CJxx
VL
L
4k or 32k OTP devices. No windowed devices
OTP
Programming
Adapters
COP8SA-PGMA
For programming 16/20/28 SOIC and 44 PLCC on the
EPU
COP8-PGMA-44QFP
COP8-PGMA-28CSP
COP8-PGMA-28SO
Contact MetaLink
L
For programming 44QFP on any programmer
For programming 28CSP on any programmer
For programming 16/20/28 SOIC on any programmer
L
VL
IM-COP8
MetaLink COP8-EPU
COP8-DM
Not available for this device
DM4-COP8-840CJ (10
MHz), plus PS-10, plus
DM-COP8/xxx (ie. 28D)
M
Included p/s (PS-10), target cable of choice (DIP or
PLCC; i.e. DM-COP8/28D), 16/20/28/40 DIP/SO and
44 PLCC programming sockets. Add OTP adapter (if
needed) and target adapter (if needed)
DM Target
Adapters
MHW-CONVxx (xx = 33,
34 etc.)
L
L
H
DM target converters for
16DIP/20/SO/28SO/44QFP/28CSP; (MHW-CNV38 for
20 pin DIP to SO package converter)
OTP
Programming
Adapters
MHW-COP8-PGMA-DS
For programming 16/20/28 SOIC and 44 PLCC on the
EPU
IM-COP8
IM-COP8-AD-464 (-220)
(10 MHz maximum)
Base unit 10 MHz; -220 = 220V; add probe card
(required) and target adapter (if needed); included
software and manuals
PC-840CJxxDW-AD-10
(xx = 20 or 28)
M
L
10 MHz 20 or 28 DIP probe card; 2.5V to 6.0V
IM Probe Target
Adapter
MHW-SOICxx (xx = 16,
20, 28)
16 or 20 or 28 pin SOIC adapter for probe card
ICU or
COP8-EVAL-ICUxx Not available for this device
National
KKD
IAR
WCOP8-IDE
EWCOP8-xx
COP8C
WCOP8-IDE
See summary above
COP8C
VL
Included in EPU and DM
L - H Included all software and manuals
Byte
Craft
M
Included all software and manuals
Aisys
DriveWay COP8
DriveWay COP8
Contact vendors
L
Included all software and manuals
OTP Programmers
L - H For approved programmer listings and vendor
information, go to our OTP support page at:
www.national.com/cop8
<
Cost: Free; VL = $100; L = $100 - $300; M = $300 - $1k; H = $1k - $3k; VH = $3k - $5k
31
www.national.com
Development Tools Support (Continued)
WHERE TO GET TOOLS
Tools are ordered directly from the following vendors. Please go to the vendor’s web site for current listings of distributors.
Vendor
Home Office
U.S.A.: Santa Clara, CA
1-408-327-8820
Electronic Sites
Other Main Offices
Distributors
Aisys
www.aisysinc.com
@
info aisysinc.com
fax: 1-408-327-8830
U.S.A.
Byte Craft
IAR
www.bytecraft.com
Distributors
@
1-519-888-6911
info bytecraft.com
fax: 1-519-746-6751
Sweden: Uppsala
+46 18 16 78 00
fax: +46 18 16 78 38
www.iar.se
U.S.A.: San Francisco
1-415-765-5500
@
info iar.se
@
info iar.com
fax: 1-415-765-5503
U.K.: London
@
info iarsys.co.uk
@
info iar.de
+44 171 924 33 34
fax: +44 171 924 53 41
Germany: Munich
+49 89 470 6022
fax: +49 89 470 956
Switzeland: Hoehe
+41 34 497 28 20
fax: +41 34 497 28 21
ICU
Sweden: Polygonvaegen
+46 8 630 11 20
www.icu.se
@
support icu.se
@
fax: +46 8 630 11 70
Denmark:
support icu.ch
KKD
www.kkd.dk
MetaLink
U.S.A.: Chandler, AZ
1-800-638-2423
www.metaice.com
Germany: Kirchseeon
80-91-5696-0
@
sales metaice.com
@
fax: 1-602-926-1198
support metaice.com
fax: 80-91-2386
@
bbs: 1-602-962-0013
www.metalink.de
islanger metalink.de
Distributors Worldwide
National
U.S.A.: Santa Clara, CA
1-800-272-9959
www.national.com/cop8
Europe: +49 (0) 180 530 8585
fax: +49 (0) 180 530 8586
Distributors Worldwide
@
support nsc.com
@
fax: 1-800-737-7018
europe.support nsc.com
The following companies have approved COP8 program-
mers in a variety of configurations. Contact your local office
or distributor. You can link to their web sites and get the lat-
est listing of approved programmers from National’s COP8
OTP Support page at: www.national.com/cop8.
Customer Support
Complete product information and technical support is avail-
able from National’s customer response centers, and from
our on-line COP8 customer support sites.
Advantech; Advin; BP Microsystems; Data I/O; Hi-Lo Sys-
tems; ICE Technology; Lloyd Research; Logical Devices;
MQP; Needhams; Phyton; SMS; Stag Programmers; Sys-
tem General; Tribal Microsystems; Xeltek.
www.national.com
32
Physical Dimensions inches (millimeters) unless otherwise noted
16-Lead Molded Package S.O. (M)
Order Number COPCJ823-XXX/WM
NS Package Number M16B
20-Lead Surface Mount Package (M)
Order Number COPCJ822-XXX/WM, COP842CJ-XXX/M, or COP942CJ-XXX/M
NS Package Number M20B
33
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
28-Lead Molded Package S.O. (M)
Order Number COPCJ820-XXX/WM, COP840CJ-XXX/M, or COP940CJ-XXX/M
NS Package Number M28B
20-Lead Molded Dual-In-Line Package (N)
Order Number COPCJ822-XXX/N, COP842CJ-XXX/N, or COP942CJ-XXX/N
NS Package Number N20A
www.national.com
34
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
28-Lead Molded Dual-In-Line Package (N)
Order Number COPCJ820-XXX/N, COP840CJ-XXX/N, or COP940CJ-XXX/N
NS Package Number N28B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Email: nsj.crc@jksmtp.nsc.com
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 87 90
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号：
COP822CJMHD-2
IC 8-BIT, UVPROM, 10 MHz, MICROCONTROLLER, CDIP20, WINDOWED, CERAMIC, DIP-20, Microcontroller
NSC
COP823CJ
8-Bit CMOS ROM Based Microcontrollers with 1k or 2k Memory, Comparator and Brown Out Detector
NSC
COP840C
8-Bit CMOS ROM Based Microcontrollers with 1k or 2k Memory, Comparator and Brown Out Detector
NSC
©2020 ICPDF网 联系我们和版权申明