LM4867_02 [NSC]
Output-Transient-Free Dual 2.1W Audop Amplifier Plus No Coupling Capacitor Stereo Headphone Function; 输出瞬态免费双2.1W Audop放大器加上无耦合电容器立体声耳机功能型号: | LM4867_02 |
厂家: | National Semiconductor |
描述: | Output-Transient-Free Dual 2.1W Audop Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
文件: | 总28页 (文件大小:845K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
August 2002
LM4867
Output-Transient-Free Dual 2.1W Audio Amplifier Plus
No Coupling Capacitor Stereo Headphone Function
General Description
Key Specifications
n PO at 1% THD+N
The LM4867 is a dual bridge-connected audio power ampli-
fier which, when connected to a 5V supply, will deliver 2.1W
to a 4Ω load (Note 1) or 2.4W to a 3Ω load (Note 2) with less
than 1.0% THD+N. The LM4867 uses advanced, latest gen-
eration circuitry to eliminate all traces of clicks and pops
when the supply voltage is first applied. The amplifier has a
headphone-amplifier-select input pin. It is used to switch the
amplifiers from bridge to single-ended mode for driving
headphones. A new circuit topology eliminates headphone
output coupling capacitors (patent pending). A MUX control
pin allows selection between the two sets of stereo input
signals. The MUX control can also be used to select be-
tween two different customer-specified closed-loop re-
sponses.
n
n
n
n
LM4867LQ, 3Ω load
LM4867LQ, 4Ω load
LM4867MTE, 4Ω
LM4867MT, 8Ω
2.4W (typ)
2.1W (typ)
1.9W (typ)
1.1W (typ)
n Single-ended mode - THD+N at 75mW into 32Ω
(max)
n Shutdown current
0.5%
0.7µA (typ)
Features
n Advanced “click and pop” suppression circuitry
n Eliminates headphone amplifier output coupling
capacitors (patent pending)
Boomer audio power amplifiers are designed specifically to
provide high quality output power from a surface mount
package and require few external components. To simplify
audio system design, the LM4867 combines dual bridge
speaker amplifiers and stereo headphone amplifiers in one
package.
n Stereo headphone amplifier mode
n Input mux control and two separate inputs per channel
n Thermal shutdown protection circuitry
n LLP, TSSOP, and exposed-DAP TSSOP packaging
available
The LM4867 features an externally controlled power-saving
micropower shutdown mode, a stereo headphone amplifier
mode, and thermal shutdown protection.
Note 1: An LM4867LQ or LM4867MTE that has been properly mounted to
a circuit board will deliver 2.1W into 4Ω. The Mux control can also be used to
select two different closed-loop responses. LM4867MT will deliver 1.1W into
8Ω. See the Application Information sections for further information concern-
ing the LM4867LQ and the LM4867MT.
Applications
n Multimedia monitors
n Portable and desktop computers
n Portable audio systems
Note 2: An LM4867LQ or LM4867MTE that has been properly mounted to a
circuit board and forced-air cooled will deliver 2.4W into 3Ω.
Connection Diagrams
20001358
Top View
Order Number LM4867MT, LM4867MTE
See NS Package Number MTC20 for TSSOP
See NS Package Number MXA20A for Exposed-DAP TSSOP
Boomer® is a registered trademark of National Semiconductor Corporation.
© 2004 National Semiconductor Corporation
DS200013
www.national.com
Connection Diagrams (Continued)
20001338
Top View
Order Number LM4867LQ
See NS Package Number LQA24A for Exposed-DAP LLP
Typical Application
20001331
* Refer to the Application Information section titled PROPER SELECTION OF EXTERNAL COMPONENTS for details concerning the value of C .
B
FIGURE 1. Typical Audio Amplifier Application Circuit
(Pin out shown for the 24-pin Exposed-DAP LLP package. Numbers in ( ) are for the 20-pin MTE and MT packages.)
www.national.com
2
Absolute Maximum Ratings (Note 3)
Thermal Resistance
θJC (typ)—MTC20
θJA (typ)—MTC20
θJC (typ)—MXA20A
θJA (typ)—MXA20A
θJA (typ)—MXA20A
θJA (typ)—MXA20A
θJC (typ)—LQA24A
θJA (typ)—LQA24A
20˚C/W
80˚C/W
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
2˚C/W
Supply Voltage
6.0V
−65˚C to +150˚C
−0.3V to VDD +0.3V
Internally limited
41˚C/W (Note 7)
51˚C/W (Note 8)
90˚C/W (Note 9)
3.0˚C/W
Storage Temperature
Input Voltage
Power Dissipation (Note 4)
ESD Susceptibility (Note 5)
42˚C/W (Note 10)
All pins except Pin 3 (MT, MTE), Pin 2 (LQ)
Pin 3 (MT, MTE), Pin 2 (LQ)
ESD Susceptibility (Note 6)
Junction Temperature
2000V
8000V
200V
Operating Ratings
Temperature Range
TMIN ≤ TA ≤ TMAX
Supply Voltage
150˚C
−40˚C ≤ TA ≤ 85˚C
2.0V ≤ VDD ≤ 5.5V
Solder Information
Small Outline Package
Vapor Phase (60 sec.)
215˚C
220˚C
Infrared (15 sec.)
See AN-450 “Surface Mounting and their Effects on
Product Reliablilty” for other methods of soldering
surface mount devices.
Electrical Characteristics for Entire IC (Notes 3, 11)
The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25˚C.
Symbol
Parameter
Conditions
LM4867
Typical Limit
Units
(Limits)
(Note 12) (Note 13)
VDD
IDD
ISD
Supply Voltage
2
V (min)
V (max)
5.5
Quiescent Power Supply Current VIN = 0V, IO = 0A (Note 14), HP-IN = 0V
VIN = 0V, IO = 0A (Note 14), HP-IN = 4V
7.5
3.0
0.7
15
6
mA (max)
mA (max)
µA (max)
Shutdown Current
VDD applied to the SHUTDOWN pin
2
Electrical Characteristics for Bridged-Mode Operation (Notes 3, 11)
The following specifications apply for VDD= 5V unless otherwise specified. Limits apply for TA= 25˚C.
Symbol
Parameter
Conditions
LM4867
Typical Limit
(Note 12) (Note 13)
Units
(Limits)
VOS
PO
Output Offset Voltage
VIN = 0V
5
50
mV (max)
Output Power (Note 15)
THD = 1%, f = 1kHz (Note 16)
LM4867MTE, RL = 3Ω
LM4867LQ, RL = 3Ω
2.2
2.4
1.9
2.1
1.1
W
W
LM4867MTE, RL = 4Ω
LM4867LQ, RL = 4Ω
W
W
LM4867, RL = 8Ω
1.0
W (min)
THD+N = 10%, f = 1kHz (Note 16)
LM4867MTE, RL = 3Ω
LM4867LQ, RL = 3Ω
3.0
3.0
2.6
2.6
1.5
0.34
W
W
W
W
W
W
LM4867MTE, RL = 4Ω
LM4867LQ, RL = 4Ω
LM4867, RL = 8Ω
THD+N = 1%, f = 1 kHz, RL = 32Ω
3
www.national.com
Electrical Characteristics for Bridged-Mode Operation (Notes 3, 11) (Continued)
The following specifications apply for VDD= 5V unless otherwise specified. Limits apply for TA= 25˚C.
Symbol
Parameter
Conditions
LM4867
Typical Limit
Units
(Limits)
(Note 12) (Note 13)
THD+N Total Harmonic Distortion+Noise 20Hz ≤ f ≤ 20kHz, AVD = 2
LM4867MTE, RL = 4Ω, PO = 2W
0.3
0.3
0.3
67
%
%
LM4867LQ, RL = 4Ω, PO = 2W
LM4867, RL = 8Ω, PO = 1W
VDD = 5V, VRIPPLE = 200 mVRMS, RL = 8Ω,
CB = 2.2µF
%
PSRR
Power Supply Rejection Ratio
dB
XTALK
SNR
Channel Separation
f = 1 kHz, CB = 2.2µF
80
97
dB
dB
Signal To Noise Ratio
VDD = 5V, PO = 1.1W, RL = 8Ω
Electrical Characteristics for Single-Ended Operation (Notes 3, 11)
The following specifications apply for VDD= 5V unless otherwise specified. Limits apply for TA= 25˚C.
Symbol
Parameter
Conditions
LM4867
Units
(Limits)
Typical
Limit
(Note 13)
50
(Note 12)
5
VOS
PO
Output Offset Voltage
Output Power
VIN = 0V
mV (max)
mW (min)
mW
THD = 0.5%, f = 1kHz, RL = 32Ω
THD+N = 1%, f = 1kHz, RL = 8Ω (Note 17)
THD+N = 1%, f = 1kHz, RL = 16Ω
THD+N = 1%, f = 1kHz, RL = 32Ω
THD+N = 10%, f = 1kHz, RL = 16Ω
THD+N = 10%, f = 1kHz, RL = 32Ω
THD = 0.05%, RL = 5kΩ
85
75
180
165
88
mW
mW
208
114
1
mW
mW
VOUT
Output Voltage Swing
VP-P
THD+N
Total Harmonic Distortion+Noise
AV = −1, PO = 75mW, 20 Hz ≤ f ≤ 20kHz,
RL = 32Ω
0.2
%
PSRR
Power Supply Rejection Ratio
CB = 2.2µF, VRIPPLE = 200mVRMS
,
52
dB
f = 1kHz
XTALK
SNR
Channel Separation
f = 1kHz, CB = 2.2µF
60
94
dB
dB
Signal To Noise Ratio
VDD = 5V, PO = 340mW, RL = 8Ω
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device operates within the Operating Ratings. Specifications are not guaranteed for parameters where
no limit is given. The typical value however, is a good indication of device performance.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
, θ , and the ambient temperature T . The maximum
A
JMAX JA
allowable power dissipation is P
= (T
− T )/θ . For the LM4867, T
= 150˚C. For the θ s for different packages, please see the Application
DMAX
JMAX
A
JA
JMAX
JA
Information section or the Absolute Maximum Ratings section.
Note 5: Human body model, 100pF discharged through a 1.5kΩ resistor.
Note 6: Machine model, 220pF–240pF discharged through all pins.
2
Note 7: The given θ is for an LM4867 packaged in an MXA20A with the Exposed-DAP soldered to an exposed 2in area of 1oz printed circuit board copper.
JA
2
Note 8: The given θ is for an LM4867 packaged in an MXA20A with the Exposed-DAP soldered to an exposed 1in area of 1oz printed circuit board copper.
JA
Note 9: The given θ is for an LM4867 packaged in an MXA20A with the Exposed-DAP not soldered to printed circuit board copper.
JA
2
Note 10: The given θ is for an LM4867 packaged in an LQA24A with the Exposed-DAP soldered to an exposed 2in area of 1oz printed circuit board copper.
JA
Note 11: All voltages are measured with respect to the ground (GND) pins, unless otherwise specified.
Note 12: Typicals are measured at 25˚C and represent the parametric norm.
Note 13: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are guaranteed by design, test, or
statistical analysis.
Note 14: The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Note 15: Output power is measured at the device terminals.
Note 16: When driving 3Ω or 4Ω loads and operating on a 5V supply, the LM4867LQ and LM4867MTE must be mounted to a circuit board that has a minimum of
2
2.5in of exposed, uniterrupted copper area connected to the LLP or TSSOP package’s exposed DAP.
Note 17: See Application Information section "Single-Ended Output Power Performance and Measurement Considerations" for more information.
www.national.com
4
Typical Performance Characteristics
MTE- and LQ- Specific Characteristics
LM4867MTE
LM4867MTE
THD+N vs Output Power
THD+N vs Frequency
20001334
20001354
20001355
20001333
LM4867LQ
LM4867LQ
THD+N vs Frequency
THD+N vs Output Power
20001353
LM4867MTE
LM4867LQ
THD+N vs Output Power
THD+N vs Output Power
20001336
5
www.national.com
Typical Performance Characteristics
MTE- and LQ- Specific Characteristics (Continued)
LM4867LQ, LM4867MTE
LM4867MTE (Note 18)
Power Dissipation vs Power Output
Power Derating Curve
20001361
20001359
LM4867LQ
Power Derating Curve
20001369
Note 18: This curve shows the LM4867MTE’s thermal dissipation ability at different ambient temperatures given these conditions:
500LFPM + JEDEC board: The part is soldered to a 1S2P 20-lead exposed-DAP TSSOP test board with 500 linear feet per minute of forced-air flow across
it. Board information - copper dimensions: 74x74mm, copper coverage: 100% (buried layer) and 12% (top/bottom layers), 16 vias under the exposed-DAP.
2
2
500LFPM + 2.5in : The part is soldered to a 2.5in , 1 oz. copper plane with 500 linear feet per minute of forced-air flow across it.
2
2
2.5in : The part is soldered to a 2.5in , 1oz. copper plane.
Not Attached: The part is not soldered down and is not forced-air cooled.
www.national.com
6
Typical Performance Characteristics
THD+N vs Frequency
THD+N vs Frequency
THD+N vs Output Power
THD+N vs Output Power
20001303
20001304
20001306
20001308
THD+N vs Frequency
20001305
THD+N vs Output Power
20001307
7
www.national.com
Typical Performance Characteristics (Continued)
THD+N vs Output Power
THD+N vs Frequency
20001365
20001363
THD+N vs Output Power
THD+N vs Frequency
20001366
20001364
Output Power vs
Load Resistance
Power Dissipation vs
Supply Voltage
20001362
20001360
www.national.com
8
Typical Performance Characteristics (Continued)
Output Power vs
Supply Voltage
Output Power vs
Supply Voltage
20001309
20001310
20001312
20001314
Output Power vs
Supply Voltage
Output Power vs
Load Resistance
20001311
Output Power vs
Load Resistance
Power Dissipation vs
Output Power
20001313
9
www.national.com
Typical Performance Characteristics (Continued)
Dropout Voltage vs
Supply Voltage
Power Derating Curve
20001315
20001316
Power Dissipation vs
Output Power
Noise Floor
20001317
20001318
Channel Separation
Channel Separation
20001319
20001320
www.national.com
10
Typical Performance Characteristics (Continued)
Power Supply
Rejection Ratio
Open Loop
Frequency Response
20001321
20001322
Supply Current vs
Supply Voltage
20001323
External Components Description
Figure 1
Components
Functional Description
1.
Ri
Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a
high pass filter with C at fc = 1/(2πRiCi).
i
2.
Ci
Input coupling capacitor which blocks the DC voltage at the amplifier’s input terminals. Also creates a
highpass filter with Ri at fc = 1/(2πRiCi). Refer to the section, Proper Selection of External Components,
for an explanation of how to determine the value of Ci.
3.
4.
Rf
Feedback resistance which sets the closed-loop gain in conjunction with Ri.
Cs
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of
External Components, for information concerning proper placement and selection of CB.
5.
CB
which the output amplifiers are typically biased and couples
the audio signal to the headphones. The signal return to
circuit ground is through the headphone jack’s sleeve.
Application Information
ELIMINATING OUTPUT COUPLING CAPACITORS
The LM4867 eliminates these coupling capacitors. Amp2A is
internally configured to apply VDD/2 to a stereo headphone
jack’s sleeve. This voltage matches the quiescent voltage
present on the Amp1A and Amp1B outputs that drive the
headphones. The headphones operate in a manner very
similar to a bridge-tied-load (BTL). The same DC voltage is
Typical single-supply audio amplifiers that can switch be-
tween driving bridge-tied-load (BTL) speakers and single-
ended (SE) headphones use a coupling capacitor on each
SE output. This capacitor blocks the half-supply voltage to
11
www.national.com
Application Information (Continued)
applied to both headphone speaker terminals. This results in
no net DC current flow through the speaker. AC current flows
through a headphone speaker as an audio signal’s output
amplitude increases on the speaker’s terminal.
When operating as a headphone amplifier, the headphone
jack sleeve is not connected to circuit ground. Using the
headphone output jack as a line-level output will place the
LM4867’s one-half supply voltage on a plug’s sleeve con-
nection. Driving a portable notebook computer or audio-
visual display equipment is possible. This presents no diffi-
culty when the external equipment uses capacitively coupled
inputs. For the very small minority of equipment that is
DC-coupled, the LM4867 monitors the current supplied by
the amplifier that drives the headphone jack’s sleeve. If this
current exceeds 500mAPK, the amplifier is shutdown, pro-
tecting the LM4867 and the external equipment. For more
information, see the section titled "Single-Ended Output
Power Performance and Measurement Considerations".
20001356
FIGURE 2. Differential output signal (Trace B) is devoid
of transients. The SHUTDOWN pin is driven by a
shutdown signal (Trace A). The inverting output (Trace
C) and the non-inverting output (Trace D) are applied
across an 8Ω BTL load.
OUTPUT TRANSIENT ("POPS AND CLICKS")
ELIMINATED
The LM4867’s pin configuration simplifies the process of
upgrading systems that use the LM4863. Except for its four
MUX function pins, the LM4867’s pin configuration matches
the LM4863’s pin configuration. If the LM4867’s MUX func-
tionality is not needed when replacing an LM4863, connect
the MUX CTRL pin to either VDD or ground. To ensure
correct amplifier operation, unused MUX inputs must be
tied to GND. As shown in Table 1, grounding the MUX CTRL
pin selects stereo input 1 (−IN A1 and −IN B1), whereas
applying VDD to the MUX CTRL pin selects stereo input 2
(−IN A2 and −IN B2).
The LM4867 contains advanced circuitry that eliminates out-
put transients ("pop and click"). This circuitry prevents all
traces of transients when the supply voltage is first applied,
when the part resumes operation after shutdown, or when
switching between BTL speakers and SE headphones. Two
circuits combine to eliminate pop and click. One circuit
mutes the output when switching between speaker loads.
Another circuit monitors the input signal. It maintains the
muted condition until there is sufficient input signal magni-
>
tude ( 60mVRMS, typ) to mask any remaining transient that
may occur.
The LM4867’s unique headphone sense circuit requires a
dual switch headphone jack. Replace the four-terminal head-
phone jack used with the LM4863 and LM4873 with the
five-terminal headphone jack, such as the Switchcraft
35RAPC4BH3, shown in Figure 4. Connect the +OUT A
(Amp2A) pin to the five-terminal headphone jack’s sleeve
pin.
Figure 2 shows the LM4867’s lack of transients in the differ-
ential signal (Trace B) across a BTL 8Ω load. The LM4867’s
active-high SHUTDOWN pin is driven by the logic signal
shown in Trace A. Trace C is the VOUT- output signal and
trace D is the VOUT+ output signal. The shutdown signal
frequency is 1Hz with a 50% duty cycle. Figure 3 is gener-
ated with the same conditions except that the output drives a
32Ω single-ended (SE) load. Again, no trace of output tran-
sients is seen.
USING THE LM4867 TO UPGRADE LM4863 AND LM4873
DESIGNS
The LM4867’s noise-free operation plus coupling-
capacitorless headphone operation and functional compat-
ibility with the LM4873 and the LM4863 simplifies upgrading
systems using these parts. Upgrading older designs that use
either the LM4863 or the LM4873 is easy. Simply remove
and short the coupling capacitors located between the
LM4873’s or LM4863’s Amp1A and Amp1B outputs and the
headphone connections. Also remove the 1kΩ resistor be-
tween each headphone connection and ground. Finally, re-
move any resistors connected to the HP-IN pin (typically two
100kΩ resistors). Connect the HP-IN pin directly to the head-
phone jack control pin as shown in Figure 4.
20001357
FIGURE 3. Single-ended output signal (Trace B) is
devoid of transients. The SHUTDOWN pin is driven by
a shutdown signal (Trace A). The inverting output
(Trace C) and the VBYPASS output (Trace D) are applied
across a 32Ω BTL load.
www.national.com
12
Application Information (Continued)
20001331
FIGURE 4. Typical Audio Amplifier Application Circuit
(Pin out shown for the 24-pin Exposed-DAP LLP package. Numbers in ( ) are for the 20-pin MTE and MT packages.)
STEREO-INPUT MULTIPLEXER (STEREO MUX)
Typical LM4867 applications use the MUX to switch between
two stereo input signals. Each stereo channel’s gain can be
tailored to produce the required output signal level by choos-
ing the appropriate input and feedback resistor ratio.
The LM4867 has two stereo inputs. The MUX CTRL Pin
controls which stereo input is active. As shown in the Truth
Table for Logic Inputs, applying 0V to the MUX CTRL input
activates stereo input 1, whereas applying VDD to the MUX
CTRL inputs activates stereo input 2. To ensure correct
amplifier operation, unused MUX inputs must be tied to
GND.
Another configuration uses the MUX to select two different
gains or frequency compensated gains that amplify a single
pair of stereo input signals. Figure 5 shows two different
feedback networks, Network 1 and Network 2. Network 1
produces increasing gain as the input signal’s frequency
decreases. This can be used to compensate a small, full-
range speaker’s low frequency response roll-off. Network 2
sets the gain for an alternate load such as headphones. The
circuit in Figure 6 uses Network 1 when driving external
speakers, switching to Network 2 when headphones are
connected. The normally closed control switch in Figure 6’s
headphone jack connects to the MUX CTRL pin. When
headphones are connected, the LM4867’s internal pull-up
that applies VDD to the HP-IN and the external 100kΩ resis-
tor applies VDD to MUX CTRL pin. Simultaneously applying
these control voltages automatically selects the amplifier
(headphone or bridge) and switches the gain (MUX channel
selection). Alternatively, leaving the MUX CTRL pin indepen-
dently accessible allows a user to select bass boost as
needed. This alternative user-selectable bass-boost scheme
requires connecting equal ratio resistor feedback networks
to each MUX input channel. The value of the resistor in the
RC network is chosen to give a gain that is necessary to
achieve the desired bass-boost.
20001370
FIGURE 5. Input MUX Example
Switching between the MUX channels may change the input
signal source or the feedback resistor network. During the
channel switching transition, the average voltage level
13
www.national.com
Note 19: If the LM4867 replaces an LM4863 and the input MUX circuitry is
Application Information (Continued)
not being used, the LM4867 MUX CTRL pin must be tied to V or GND and
DD
the unused MUX inputs must be connected to GND.
present on the internal amplifier’s input may change. This
change can slew at a rate that may produce audible voltage
transients or clicks in the amplifier’s output signal. Using the
MUX to select between two vastly dissimilar gains is a typical
transient-producing situation. As the MUX is switched, an
audible click may occur as the gain suddenly changes.
PIN OUT COMPATIBILITY WITH THE LM4863
The LM4867 pin out was designed to simplify replacing the
LM4863: except for the four Pins(-IN A2, MUX CTRL, -IN B2,
and NC) that implement the LM4867’s extra functionality, the
LM4867MT/MTE and LM4863MT/MTE pin outs match.
(Note 19)
20001339
FIGURE 6. As configured, connecting headphones to this jack automatically selects the stereo headphone amplifier
and, with the additional NC switch, changes MUX channels (Network 2 in Figure 5 )
EXPOSED-DAP MOUNTING CONSIDERATIONS
Best thermal performance is achieved with the largest prac-
tical copper heat sink area. If the heatsink and amplifier
share the same PCB layer, a nominal 2.5in2 (min) area is
necessary for 5V operation with a 4Ω load. Heatsink areas
not placed on the same PCB layer as the LM4867 should be
5in2 (min) for the same supply voltage and load resistance.
The last two area recommendations apply for 25˚C ambient
temperature. Increase the area to compensate for ambient
temperatures above 25˚C. In systems using cooling fans, the
LM4867MTE can take advantage of forced air cooling. With
an air flow rate of 450 linear-feet per minute and a 2.5in2
exposed copper or 5.0in2 inner layer copper plane heatsink,
the LM4867MTE can continuously drive a 3Ω load to full
power. The LM4867LQ achieves the same output power
level without forced-air cooling. In all circumstances and
under all conditions, the junction temperature must be held
below 150˚C to prevent activating the LM4867’s thermal
shutdown protection. The LM4867’s power de-rating curve in
the Typical Performance Characteristics shows the maxi-
mum power dissipation versus temperature. Example PCB
layouts for the exposed-DAP TSSOP and LQ packages are
shown in the Demonstration Board Layout section. Further
detailed and specific information concerning PCB layout and
fabrication and mounting an LQ (LLP) is found in National
Semiconductor’s AN1187.
The LM4867’s exposed-DAP (die attach paddle) packages
(MTE and LQ) provide a low thermal resistance between the
die and the PCB to which the part is mounted and soldered.
This allows rapid heat transfer from the die to the surround-
ing PCB copper area heatsink, copper traces, ground plane,
and finally, surrounding air. The result is a low voltage audio
power amplifier that produces 2.4W dissipation in a 4Ω load
at ≤ 1% THD+N and over 3W in a 3Ω load at 10% THD+N.
This high power is achieved through careful consideration of
necessary thermal design. Failing to optimize thermal design
may compromise the LM4867’s high power performance and
activate unwanted, though necessary, thermal shutdown
protection.
The MTE and LQ packages must have their DAPs soldered
to a copper pad on the PCB. The DAP’s PCB copper pad is
then, ideally, connected to a large plane of continuous un-
broken copper. This plane forms a thermal mass, heat sink,
and radiation area. Place the heat sink area on either outside
plane in the case of a two-sided or multi-layer PCB. (The
heat sink area can also be placed on an inner layer of a
multi-layer board. The thermal resistance, however, will be
higher.) Connect the DAP copper pad to the inner layer or
backside copper heat sink area with 32 (4 X 8) (MTE) or 6 (3
X 2) (LQ) vias. The via diameter should be 0.012in - 0.013in
with a 1.27mm pitch. Ensure efficient thermal conductivity by
plugging and tenting the vias with plating and solder mask,
respectively.
www.national.com
14
order to choose an amplifier’s closed-loop gain without caus-
ing excessive clipping, please refer to the Audio Power
Amplifier Design section.
Application Information (Continued)
PCB LAYOUT AND SUPPLY REGULATION
CONSIDERATIONS FOR DRIVING 3Ω AND 4Ω LOADS
Another advantage of the differential bridge output is no net
DC voltage across the load. This is accomplished by biasing
channel A’s and channel B’s outputs at half-supply. This
eliminates the coupling capacitor that single supply, single-
ended amplifiers require. Eliminating an output coupling ca-
pacitor in a single-ended configuration forces a single-supply
amplifier’s half-supply bias voltage across the load. This
increases internal IC power dissipation and may perma-
nently damage loads such as speakers.
Power dissipated by a load is a function of the voltage swing
across the load and the load’s impedance. As load imped-
ance decreases, load dissipation becomes increasingly de-
pendent on the interconnect (PCB trace and wire) resistance
between the amplifier output pins and the load’s connec-
tions. Residual trace resistance causes a voltage drop,
which results in power dissipated in the trace and not in the
load as desired. For example, 0.1Ω trace resistance reduces
the output power dissipated by a 4Ω load from 2.1W to 2.0W.
The problem of decreased load dissipation is exacerbated
as load impedance decreases. Therefore, to maintain the
highest load dissipation and widest output voltage swing,
PCB traces that connect the output pins to a load must be as
wide as possible.
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful single-ended or bridged amplifier. Equation (2)
states the maximum power dissipation point for a single-
ended amplifier operating at a given supply voltage and
driving a specified output load.
Poor power supply regulation adversely affects maximum
output power. A poorly regulated supply’s output voltage
decreases with increasing load current. Reduced supply
voltage causes decreased headroom, output signal clipping,
and reduced output power. Even with tightly regulated sup-
plies, trace resistance creates the same effects as poor
supply regulation. Therefore, making the power supply
traces as wide as possible helps maintain full output voltage
swing.
PDMAX = (VDD)2/(2π2RL): Single-Ended
(2)
However, a direct consequence of the increased power de-
livered to the load by a bridge amplifier is higher internal
power dissipation for the same conditions.
The LM4867 has two operational amplifiers per channel. The
maximum internal power dissipation per channel operating in
the bridge mode is four times that of a single-ended ampli-
fier. From Equation (3), assuming a 5V power supply and an
4Ω load, the maximum single channel power dissipation is
1.27W or 2.54W for stereo operation.
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 4, the LM4867 consists of two pairs of
operational amplifiers, forming a two-channel (channel A and
channel B) stereo amplifier. (Though the following discusses
channel A, it applies equally to channel B.) External resistors
Rf and Ri set the closed-loop gain of Amp1A, whereas two
internal 20kΩ resistors set Amp2A’s gain at -1. The LM4867
drives a load, such as a speaker, connected between the two
amplifier outputs, -OUTA and +OUTA.
PDMAX = 4 * (VDD)2/(2π2RL): Bridge Mode (3)
The LM4867’s power dissipation is twice that given by Equa-
tion (2) or Equation (3) when operating in the single-ended
mode or bridge mode, respectively. Twice the maximum
power dissipation point given by Equation (3) must not ex-
ceed the power dissipation given by Equation (4):
Figure 4 shows that Amp1A’s output serves as Amp2A’s
input. This results in both amplifiers producing signals iden-
tical in magnitude, but 180˚ out of phase. Taking advantage
of this phase difference, a load is placed between -OUTA
and +OUTA and driven differentially ("commonly referred to
as bridge mode"). This results in a differential gain of
PDMAX’ = (TJMAX − TA)/θJA
(4)
AVD = 2 * (Rf/R )
(1)
The LM4867’s TJMAX = 150˚C. In the LQ package soldered
to a DAP pad that expands to a copper area of 5in2 on a
PCB, the LM4867’s θJA is 20˚C/W. In the MTE package
soldered to a DAP pad that expands to a copper area of 2in2
on a PCB, the LM4867’s θJA is 41˚C/W. At any given ambient
temperature TA, use Equation (4) to find the maximum inter-
nal power dissipation supported by the IC packaging. Rear-
ranging Equation (4) and substituting PDMAX for PDMAX’ re-
sults in Equation (5). This equation gives the maximum
ambient temperature that still allows maximum stereo power
dissipation without violating the LM4867’s maximum junction
temperature.
i
Bridge mode amplifiers are different from single-ended am-
plifiers that drive loads connected between a single amplifi-
er’s output and ground. For a given supply voltage, bridge
mode has a distinct advantage over the single-ended con-
figuration: its differential output doubles the voltage swing
across the load. This produces four times the output power
when compared to a single-ended amplifier under the same
conditions. This increase in attainable output power as-
sumes that the amplifier is not current limited or that the
output signal is not clipped. To ensure minimum output sig-
nal clipping when choosing an amplifier’s closed-loop gain,
refer to the Audio Power Amplifier Design section.
TA = TJMAX − 2 X PDMAX θJA
(5)
A bridge amplifier design has a few distinct advantages over
the single-ended configuration, as it provides differential
drive to the load, thus doubling the output swing for a speci-
fied supply voltage. Four times the output power is possible
as compared to a single-ended amplifier under the same
conditions. This increase in attainable output power as-
sumes that the amplifier is not current limited or clipped. In
For a typical application with a 5V power supply and an 4Ω
load, the maximum ambient temperature that allows maxi-
mum stereo power dissipation without exceeding the maxi-
mum junction temperature is approximately 99˚C for the LQ
package and 45˚C for the MTE package.
15
www.national.com
ground as short as possible. Connecting a 1µF capacitor,
CB, between the BYPASS pin and ground improves the
internal bias voltage’s stability and improves the amplifier’s
PSRR. The PSRR improvements increase as the bypass pin
capacitor value increases. Too large, however, increases
turn−on time and can compromise the amplifier’s click and
pop performance. The selection of bypass capacitor values,
especially CB, depends on desired PSRR requirements,
click and pop performance (as explained in the section,
Proper Selection of External Components), system cost,
and size constraints.
Application Information (Continued)
TJMAX = PDMAX θJA + TA
(6)
Equation (6) gives the maximum junction temperature
TJMAX. If the result violates the LM4867’s 150˚C, reduce the
maximum junction temperature by reducing the power sup-
ply voltage or increasing the load resistance. Further allow-
ance should be made for increased ambient temperatures.
The above examples assume that a device is a surface
mount part operating around the maximum power dissipation
point. Since internal power dissipation is a function of output
power, higher ambient temperatures are allowed as output
power or duty cycle decreases.
MICRO−POWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the
LM4867’s shutdown function. Activate micro−power shut-
down by applying VDD to the SHUTDOWN pin. When active,
the LM4867’s micro−power shutdown feature turns off the
amplifier’s bias circuitry, reducing the supply current. The
logic threshold is typically VDD/2. The low 0.7µA typical
shutdown current is achieved by applying a voltage that is as
near as VDD as possible to the SHUTDOWN pin. A voltage
that is less than VDD may increase the shutdown current.
Table 1 shows the logic signal levels that activate and deac-
tivate micro−power shutdown and headphone amplifier op-
eration. To ensure that the output signal remains
transient−free, do not cycle the shutdown function
faster than 1Hz.
If the result of Equation (2) is greater than that of Equation
(3), then decrease the supply voltage, increase the load
impedance, or reduce the ambient temperature. If these
measures are insufficient, a heat sink can be added to
reduce θJA. The heat sink can be created using additional
copper area around the package, with connections to the
ground pin(s), supply pin and amplifier output pins. External,
solder attached SMT heatsinks such as the Thermalloy
7106D can also improve power dissipation. When adding a
heat sink, the θJA is the sum of θJC, θCS, and θSA. (θJC is the
junction−to−case thermal impedance, θCS is the
case−to−sink thermal impedance, and θSA is the
sink−to−ambient thermal impedance.) Refer to the Typical
Performance Characteristics curves for power dissipation
information at lower output power levels.
There are a few ways to control the micro−power shutdown.
These include using a single−pole, single, throw switch, a
microprocessor, or a microcontroller. When using a switch,
connect an external 100kΩ pull−up resistor between the
SHUTDOWN pin and VDD. Connect the switch between the
SHUTDOWN pin and ground. Select normal amplifier opera-
tion by closing the switch. Opening the switch connects the
SHUTDOWN pin to VDD through the pull−up resistor, acti-
vating micro−power shutdown. The switch and resistor guar-
antee that the SHUTDOWN pin will not float. This prevents
unwanted state changes. In a system with a microprocessor
or a microcontroller, use a digital output to apply the control
voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin
with active circuitry eliminates the pull up resistor.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10µF in parallel with a 0.1µF filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0µF
tantalum bypass capacitance connected between the
LM4867’s supply pins and ground. Do not substitute a ce-
ramic capacitor for the tantalum. Doing so may cause oscil-
lation. Keep the length of leads and traces that connect
capacitors between the LM4867’s power supply pin and
Truth Table for Logic Inputs
SHUTDOWN
PIN
HP-IN
PIN
MUX CHANNEL
INPUT SELECT
Logic Low
Logic High
Logic Low
Logic High
X
OPERATIONAL MODE (MUX
INPUTCHANNEL #)
Logic Low
Logic Low
Logic Low
Logic Low
Logic High
= −OUTB signal
= −OUTB signal
Bridged amplifiers (1)
Bridged amplifiers (2)
≠
≠
−OUTB signal
−OUTB signal
X
Single-ended amplifiers (1)
Single-ended amplifiers (2)
Micro−power shutdown
the VDD/2 voltage present on pin 14. The result is muted
bridge-connected loads. Quiescent current consumption is
reduced when the IC is in this single−ended mode.
HEADPHONE (SINGLE-ENDED) AMPLIFIER
OPERATION
Figure 8 shows the implementation of the LM4867’s head-
phone control function. An internal comparator with a nomi-
nal 400mV offset monitors the signal present at the −OUTB
output. It compares this signal against the signal applied to
the HP−IN pin. When these signals are equal, as is the case
when a BTL is connected to the amplifier, the comparator
forces the LM4867 to maintain bridged−amplifier operation.
When the HP−IN pin is externally floated, such as when
An internal pull−up circuit is connected to the HP−IN (pin 20)
headphone amplifier control pin. When this pin is left uncon-
nected, VDD is applied to the HP−IN. This turns off Amp2B
and switches Amp2A’s input signal from an audio signal to
www.national.com
16
Figure 7 shows an optional resistor connected between the
amplifier output that drives the headphone jack sleeve and
ground. This resistor provides a ground path that supressed
power supply hum. This hum may occur in applications such
as notebook computers in a shutdown condition and con-
nected to an external powered speaker. The resistor’s 100Ω
value is a suggested starting point. Its final value must be
determined based on the tradeoff between the amount of
noise suppression that may be needed and minimizing the
additional current drawn by the resistor (25mA for a 100Ω
resistor and a 5V supply).
Application Information (Continued)
headphones are connected to the jack shown in Figure 8,
and internal pull−up forces VDD on the internal comparator’s
HP−IN inputs. This changes the comparator’s output state
and enables the headphone function: it turns off Amp2B,
switches Amp2A’s input signal from an audio signal to the
VDD/2 voltage present on pin 14, and mutes the bridge-
connected loads. Amp1A and Amp1B drive the headphones.
Figure 8 also shows the suggested headphone jack electri-
cal connections. The jack is designed to mate with a
three−wire plug. The plug’s tip and ring should each carry
one of the two stereo output signals, whereas the sleeve
provides the return to Amp2A. A headphone jack with one
control pin contact is sufficient to drive the HP−IN pin when
connecting headphones.
ESD PROTECTION
As stated in the Absolute Maximum Ratings, pin 28 on the
MT and MH packages have a maximum ESD susceptibility
rating of 8000V. For higher ESD voltages, the addition of a
PCDN042 dual transil (from California Micro Devices), as
shown in Figure 7, will provide additional protection.
A switch can replace the headphone jack contact pin. When
a switch shorts the HP−IN pin to VDD, bridge−connected
speakers are muted and Amp1A and Amp2A drive a pair of
headphones. When a switch shorts the HP−IN pin to GND,
the LM4867 operates in bridge mode. If headphone drive is
not needed, short the HP−IN pin to the −OUTB pin.
20001371
FIGURE 7. The PCDN042 provides additional ESD protection beyond the 8000V shown in the Absolute Maximum
Ratings for the AMP2A output
SINGLE-ENDED OUTPUT POWER PERFORMANCE
AND MEASUREMENT CONSIDERATIONS
sleeve. An on-board circuit monitors this amplifier’s output
current. The sudden increase in THD+N is caused by the
current limit circuitry forcing AMP2A into a high−impedance
output mode. When this occurs, the output waveform has
discontinuities that produce large amounts of distortion. It
has been observed that as the output power is steadily
increased, the distortion may jump from 5% to greater than
35%. Indeed, 10% THD+N may not actually be achievable.
The LM4867 delivers clean, low distortion SE output power
into loads that are greater than 10Ω. As an example, output
power for 16Ω and 32Ω loads are shown in the Typical
Performance Characteristic curves. For loads less than
10Ω, the LM4876 can typically supply 180mW of low distor-
tion power. However, when higher dissipation is desired in
loads less than 10Ω, a dramatic increase in THD+N may
occur. This is normal operation and does not indicate that
proper functionality has ceased. When a jump from moder-
ate to excessively high distortion is seen, simply reducing
the output voltage swing will restore the clean, low distortion
SE operation.
USING THE SINGLE−ENDED OUTPUT FOR LINE
LEVEL APPLICATIONS
Some samples of the LM4867 may exhibit small amplitude,
high frequency oscillation when the SE output is connected
to a line-level input. This oscillation can be eliminated by
connecting a 5%, 300Ω resistor between Amp2A’s output pin
and each amplifier, AMP1A and AMP1B, output.
The dramatic jump in distortion for loads less than 10Ω
occurs when current limiting circuitry activates. During SE
operation, AMP2A (refer to Figure 4) drives the headphone
17
www.national.com
Application Information (Continued)
20001324
FIGURE 8. Headphone Circuit
(Pin numbers in ( ) are for the 20-pin MTE and MT packages.)
INPUT CAPACITOR VALUE SELECTION
1.0µF along with a small value of Ci (in the range of 0.1µF to
0.39µF), produces a click-less and pop-less shutdown func-
tion. As discussed above, choosing Ci no larger than neces-
sary for the desired bandwidth helps minimize clicks and
pops. CB’s value should be in the range of 5 times to 7 times
the value of Ci. This ensures that output transients are
eliminated when power is first applied or the LM4867 re-
sumes operation after shutdown.
Amplifying the lowest audio frequencies requires high value
input coupling capacitor (Ci in Figure 4). A high value capaci-
tor can be expensive and may compromise space efficiency
in portable designs. In many cases, however, the speakers
used in portable systems, whether internal or external, have
little ability to reproduce signals below 150Hz. Applications
using speakers with this limited frequency response reap
little improvement by using large input capacitor.
OPTIMIZING CLICK AND POP REDUCTION
PERFORMANCE
Besides effecting system cost and size, Ci has an affect on
the LM4867’s click and pop performance. When the supply
voltage is first applied, a transient (pop) is created as the
charge on the input capacitor changes from zero to a quies-
cent state. The magnitude of the pop is directly proportional
to the input capacitor’s size. Higher value capacitors need
more time to reach a quiescent DC voltage (usually VDD/2)
when charged with a fixed current. The amplifier’s output
charges the input capacitor through the feedback resistor,
Rf. Thus, pops can be minimized by selecting an input
capacitor value that is no higher than necessary to meet the
desired −3dB frequency and is between 0.14CB and 0.20CB.
The LM4867 contains circuitry that eliminates turn-on and
shutdown transients (“clicks and pops“) and transients that
could occur when switching between BTL speakers and
single-ended headphones. For this discussion, turn-on re-
fers to either applying the power supply voltage or when the
shutdown mode is deactivated. While the power supply is
ramping to its final value, the LM4867’s internal amplifiers
are configured as unity gain buffers and are disconnected
from the -OUT and +OUT pins. An internal current source
changes the voltage of the BYPASS pin in a controlled,
linear manner. Ideally, the input and outputs track the voltage
applied to the BYPASS pin. The gain of the internal amplifi-
ers remains unity until the voltage on the bypass pin reaches
1/2 VDD. As soon as the voltage on the bypass pin is stable,
the device becomes fully operational and the amplifier out-
puts are reconnected to the -OUT and +OUT pins. Although
the BYPASS pin current cannot be modified, changing the
size of CB alters the device’s turn-on time. There is a linear
relationship between the size of CB and the turn-on time.
Here are some typical turn-on times for various values of CB:
A shown in Figure 4, the input resistor (RI) and the input
capacitor, CI produce a −3dB high pass filter cutoff frequency
that is found using Equation (7).
f−3dB = 1/(2πRINCI)
(7)
As an example when using a speaker with a low frequency
limit of 150Hz, Ci, using Equation (4) is 0.063µF. The 1.0µF
Ci shown in Figure 4 allows the LM4867 to drive high effi-
ciency, full range speaker whose response extends below
30Hz.
CB
TON
3ms
0.01µF
0.1µF
0.22µF
0.47µF
1.0µF
2.2µF
BYPASS CAPACITOR VALUE SELECTION
30ms
63ms
Besides minimizing the input capacitor size, careful consid-
eration should be paid to value of CB, the capacitor con-
nected to the BYPASS pin. Since CB determines how fast
the LM4867 settles to quiescent operation, its value is critical
when minimizing turn-on pops. The slower the LM4867’s
outputs ramp to their quiescent DC voltage (nominally 1/2
VDD), the smaller the turn-on pop. Choosing CB equal to
134ms
300ms
630ms
www.national.com
18
Thus, a minimum gain of 2.83 allows the LM4867’s to reach
full output swing and maintain low noise and THD+N perfor-
mance. For this example, let AVD = 3.
Application Information (Continued)
In order eliminate “clicks and pops“, all capacitors must be
discharged before turn-on. Rapidly switching VDD may not
allow the capacitors to fully discharge, which may cause
“clicks and pops“.
The amplifier’s overall gain is set using the input (Ri) and
feedback (Ri) resistors. With the desired input impedance
set at 20kΩ, the feedback resistor is found using Equation
(11).
Rf/Ri = AVD/2
(11)
NO LOAD STABILITY
The LM4867 may exhibit low level oscillation when the load
resistance is greater than 10kΩ. This oscillation only occurs
as the output signal swings near the supply voltages. Pre-
vent this oscillation by connecting a 5kΩ between the output
pins and ground.
The value of Rf is 30kΩ.
The last step in this design example is setting the amplifier’s
−3dB frequency bandwidth. To achieve the desired 0.25dB
pass band magnitude variation limit, the low frequency re-
sponse must extend to at least one-fifth the lower bandwidth
limit and the high frequency response must extend to at least
five times the upper bandwidth limit. The gain variation for
both response limits is 0.17dB, well within the 0.25dB
desired limit. The results are an
AUDIO POWER AMPLIFIER DESIGN
Audio Amplifier Design: Driving 1W into an 8Ω Load
The following are the desired operational parameters:
fL = 100Hz/5 = 20Hz
(12)
Power Output:
Load Impedance:
Input Level:
1 WRMS
8Ω
1 VRMS
and an
fH = 20kHz x 5 = 100kHz
(13)
Input Impedance:
Bandwidth:
20 kΩ
100 Hz−20 kHz 0.25 dB
As mentioned in the Selecting Proper External Compo-
nents section, Ri and Ci create a highpass filter that sets the
amplifier’s lower bandpass frequency limit. Find the coupling
capacitor’s value using Equation (12).
The design begins by specifying the minimum supply voltage
necessary to obtain the specified output power. One way to
find the minimum supply voltage is to use the Output Power
vs Supply Voltage curve in the Typical Performance Char-
acteristics section. Another way, using Equation (8), is to
calculate the peak output voltage necessary to achieve the
desired output power for a given load impedance. To ac-
count for the amplifier’s dropout voltage, two additional volt-
ages, based on the Dropout Voltage vs Supply Voltage in the
Typical Performance Characteristics curves, must be
added to the result obtained by Equation (8). The result is
Equation (9).
Ci≥ 1/(2πR ifL)
(14)
The result is
1/(2π*20kΩ*20Hz) = 0.397µF
(15)
Use a 0.39µF capacitor, the closest standard value.
The product of the desired high frequency cutoff (100kHz in
this example) and the differential gain AVD, determines the
upper passband response limit. With AVD = 3 and fH
=
100kHz, the closed-loop gain bandwidth product (GBWP) is
300kHz. This is less than the LM4867’s 3.5MHz GBWP. With
this margin, the amplifier can be used in designs that require
more differential gain while avoiding performance,restricting
bandwidth limitations.
(8)
VDD ≥ (VOUTPEAK+ (VOD
+ VODBOT))
(9)
TOP
RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT
The Output Power vs Supply Voltage graph for an 8Ω load
indicates a minimum supply voltage of 4.6V. This is easily
met by the commonly used 5V supply voltage. The additional
voltage creates the benefit of headroom, allowing the
LM4867 to produce peak output power in excess of 1W
without clipping or other audible distortion. The choice of
supply voltage must also not create a situation that violates
of maximum power dissipation as explained above in the
Power Dissipation section.
Figures 8 through 12 show the recommended four-layer PC
board layout that is optimized for the 24-pin LQ-packaged
LM4867 and associated external components. Figures 13
through 17 show the recommended four-layer PC board
layout that is optimized for the 24-pin MTE-packaged
LM4867 and associated external components. Figures 18
through 20 show the recommended two-layer PC board
layout that is optimized for the 20-pin MT-packaged LM4867
and associated external components. These circuits are de-
signed for use with an external 5V supply and 4Ω speakers.
After satisfying the LM4867’s power dissipation require-
ments, the minimum differential gain needed to achieve 1W
dissipation in an 8Ω load is found using Equation (10).
These circuit boards are easy to use. Apply 5V and ground to
the board’s VDD and GND pads, respectively. Connect 4Ω
speakers between the board’s −OUTA and +OUTA and
OUTB and +OUTB pads.
(10)
19
www.national.com
Application Information (Continued)
20001340
FIGURE 9. Recommended LQ PC Board Layout:
Component-Side Silkscreen
20001341
FIGURE 10. Recommended LQ PC Board Layout:
Component-Side Layout
www.national.com
20
Application Information (Continued)
20001342
FIGURE 11. Recommended LQ PC Board Layout:
Upper Inner-Layer Layout
20001343
FIGURE 12. Recommended LQ PC Board Layout:
Lower Inner-Layer Layout
21
www.national.com
Application Information (Continued)
20001344
FIGURE 13. Recommended LQ PC Board Layout:
Bottom-Side Layout
20001345
FIGURE 14. Recommended MTE PC Board Layout:
Component-Side Silkscreen
www.national.com
22
Application Information (Continued)
20001346
FIGURE 15. Recommended MTE PC Board Layout:
Component-Side Layout
20001347
FIGURE 16. Recommended MTE PC Board Layout:
Upper Inner-Layer Layout
23
www.national.com
Application Information (Continued)
20001348
FIGURE 17. Recommended MTE PC Board Layout:
Lower Inner-Layer Layout
20001349
FIGURE 18. Recommended MTE PC Board Layout:
Bottom-Side Layout
www.national.com
24
Application Information (Continued)
20001350
FIGURE 19. Recommended MT PC Board Layout:
Component-Side Silkscreen
20001351
FIGURE 20. Recommended MT PC Board Layout:
Component-Side Layout
25
www.national.com
Application Information (Continued)
20001352
FIGURE 21. Recommended MT PC Board Layout:
Bottom-Side Layout
www.national.com
26
Physical Dimensions inches (millimeters)
unless otherwise noted
24-Lead MOLDED PKG, Leadless Leadframe Package LLP
Order Number LM4867LQ
NS Package Number LQA24A
20-Lead MOLDED PKG, TSSOP, JEDEC, 4.4mm BODY WIDTH
Order Number LM4867MT
NS Package Number MTC20
27
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
20-Lead MOLDED TSSOP, EXPOSED PAD, 6.5x4.4x0.9mm
Order Number LM4867MTE
NS Package Number MXA20A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号:
LM4868
Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function
NSC
LM4868LQ
Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function
NSC
LM4868MT
Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function
NSC
LM4868MTE
Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function
NSC
LM4868MTE/NOPB
IC 3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20, 6.50 X 4.40 MM, 0.90 MM HEIGHT, EXPOSED PAD, PLASTIC, TSSOP-20, Audio/Video Amplifier
TI
LM4868MTEX
3W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20, 6.50 X 4.40 MM, 0.90 MM HEIGHT, EXPOSED PAD, PLASTIC, TSSOP-20
TI
LM4868MTEX/NOPB
3W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20, 6.50 X 4.40 MM, 0.90 MM HEIGHT, EXPOSED PAD, PLASTIC, TSSOP-20
TI
©2020 ICPDF网 联系我们和版权申明