LM4881MM [NSC]
Dual 200 mW Headphone Amplifier with Shutdown Mode; 双200毫瓦耳机放大器，具有关断模式
| 型号： | LM4881MM |
| 厂家： | 
National Semiconductor |
| 描述： | Dual 200 mW Headphone Amplifier with Shutdown Mode |
| 文件： | 总11页 (文件大小：416K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
September 1997
LM4881
Dual 200 mW Headphone Amplifier with Shutdown Mode
General Description
Key Specifications
The LM4881 is a dual audio power amplifier capable of deliv-
ering 200 mW of continuous average power into an 8Ω load
with 0.1% (THD) from a 5V power supply.
n THD at 1 kHz at 125 mW
continuous average output
power into 8Ω
0.1% (max)
0.02% (typ)
Boomer audio power amplifiers were designed specifically to
provide high quality output power with a minimal amount of
external components using surface mount packaging. Since
the LM4881 does not require bootstrap capacitors or snub-
ber networks, it is optimally suited for low-power portable
systems.
n THD at 1 kHz at 75 mW continuous
average output power into 32Ω
n Output power at 10 THD+N
%
at 1 kHz into 8Ω
300 mW (typ)
0.7 µA (typ)
n Shutdown Current
The LM4881 features an externally controlled, low power
consumption shutdown mode which is virtually clickless and
popless, as well as an internal thermal shutdown protection
mechanism.
Features
n MSOP surface mount packaging
n Unity-gain stable
The unity-gain stable LM4881 can be configured by external
gain-setting resistors.
n External gain configuration capability
n Thermal shutdown protection circuitry
n No bootstrap capacitors, or snubber circuits are
necessary
Applications
n Headphone Amplifier
n Personal Computers
n Microphone Preamplifier
Typical Application
Connection Diagrams
MSOP Package
DS100005-2
SOP and DIP Package
DS100005-1
*Refer to the Application Information Section for information concerning
proper selection of the input and output coupling capacitors.
DS100005-38
FIGURE 1. Typical Audio Amplifier Application Circuit
Top View
Order Number LM4881MM, LM4881M, or LM4881N
See NS Package Number MUA08A, M08A, or N08E
Boomer® is a registered trademark of National Semiconductor Corporation.
© 1999 National Semiconductor Corporation
DS100005
www.national.com
Absolute Maximum Ratings (Note 3)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Thermal Resistance
θJC (MSOP)
θJA (MSOP)
θJC (SOP)
56˚C/W
210˚C/W
35˚C/W
θJA (SOP)
170˚C/W
37˚C/W
Supply Voltage
6.0V
−65˚C to +150˚C
−0.3V to VDD + 0.3V
Internally limited
3500V
θJC (DIP)
Storage Temperature
Input Voltage
θJA (DIP)
107˚C/W
Power Dissipation (Note 4)
ESD Susceptibility (Note 5)
ESD Susceptibility (Note 6)
Junction Temperature
Soldering Information (Note 1)
Small Outline Package
Vapor Phase (60 seconds)
Infrared (15 seconds)
Operating Ratings
Temperature Range
TMIN ≤ TA ≤ TMAX
Supply Voltage
250V
150˚C
−40˚C ≤ T ≤ 85˚C
A
2.7V ≤ VDD ≤ 5.5V
Note 1: See AN-450 “Surface Mounting and their Effects on Product Reli-
ability” for other methods of soldering surface mount devices.
215˚C
220˚C
Electrical Characteristics (Notes 2, 3)
The following specifications apply for VDD = 5V unless otherwise specified. Limits apply for TA = 25C.
Symbol
Parameter
Conditions
LM4881
Units (Limits)
Typ (Note 7)
Limit (Note 8)
VDD
Power Supply Voltage
2.7
5.5
6.0
5
V (min)
V (max)
IDD
ISD
Quiescent Current
Shutdown Current
Offset Voltage
VIN = 0V, IO = 0A
3.6
0.7
5
mA (max)
µA (max)
mV (max)
VPIN1 = VDD
VOS
P O
VIN = 0V
50
Output Power
THD = 0.1% (max); f = 1 kHz;
RL = 8Ω
200
150
85
125
mW (min)
mW
RL = 16Ω
RL = 32Ω
mW
THD + N = 10%; f = 1 kHz;
RL = 8Ω
300
200
mW
mW
mW
%
RL = 16Ω
RL = 32Ω
110
THD+N
PSRR
Total Harmonic Distortion +
Noise
RL = 16Ω, P = 120 mWrms;
0.025
0.02
O
RL = 32Ω, PO = 75 mWrms;
%
f = 1 kHz
CB = 1.0 µF, VRIPPLE = 200
mVrms, f = 120Hz
50
dB
www.national.com
2
Electrical Characteristics (Notes 2, 3)
The following specifications apply for VDD = 3V unless otherwise specified. Limits apply for TA = 25C.
Symbol
Parameter
Conditions
LM4881
Typ (Note 7) Limit (Note 8)
Units (Limits)
IDD
ISD
Quiescent Current
Shutdown Current
Offset Voltage
VIN = 0V, IO = 0A
1.1
0.7
5
mA
µA
VPIN1 = VDD
VIN = 0V
VOS
P O
mV
Output Power
THD = 1% (max);
f = 1 kHz;
RL = 8Ω
RL= 16Ω
RL = 32Ω
70
65
30
mW
mW
mW
THD + N = 10%;
f = 1 kHz;
RL = 8Ω
RL = 16Ω
RL = 32Ω
95
65
mW
mW
mW
%
35
THD+N Total Harmonic Distortion +
Noise
RL = 16Ω, P = 60 mWrms;
0.2
0.03
O
RL = 32Ω, PO
25 mWrms; f = 1 kHz
Power Supply Rejection Ratio CB = 1.0 µF, VRIPPLE
200 mVrms, f = 100 Hz
=
%
PSRR
=
50
dB
Note 2: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func-
tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar-
antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is
given, however, the typical value is a good indication of device performance.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
, θ , and the ambient temperature T . The maximum
A
JMAX JA
allowable power dissipation is P
= (T
JMAX
− T ) / θ . For the LM4881, T
JA
= 150˚C, and the typical junction-to-ambient thermal resistance, when board
JMAX
DMAX
A
mounted, is 210˚C/W for the MSOP Package and 107˚C/W for package N08E.
Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 6: Machine Model, 220 pF–240 pF discharged through all pins.
Note 7: Typicals are measured at 25˚C and represent the parametric norm.
Note 8: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
3
www.national.com
External Components Description (Figure 1)
Compo-
nents
Functional Description
1. Ri
Inverting input resistance which sets the closed-loop gain in conjuction with Rf. This resistor also
forms a high pass filter with Ci at fc = 1 / (2πR Ci).
i
2. Ci
Input coupling capacitor which blocks the DC voltage at the amplifier’s input terminals. Also creates a
highpass filter with Ri at fc = 1 / (2πRiC ). Refer to the section, Proper Selection of External
i
Components, for and explanation of how to determine the value of Ci.
3. Rf
Feedback resistance which sets closed-loop gain in conjuction with Ri.
4. CS
Supply bypass capacitor which provides power supply filtering. Refer to the Application Information
section for proper placement and selection of the supply bypass capacitor.
5. CB
6. CO
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of
External Components, for information concerning proper placement and selection of CB.
Output coupling capacitor which blocks the DC voltage at the amplifier’s output. Forms a high pass
filter with RL at fO = 1/(2πRLCO)
Typical Performance Characteristics
THD+N vs Frequency
THD+N vs Frequency
THD+N vs Frequency
DS100005-3
DS100005-4
DS100005-5
THD+N vs Frequency
THD+N vs Frequency
THD+N vs Frequency
DS100005-6
DS100005-7
DS100005-8
www.national.com
4
Typical Performance Characteristics (Continued)
THD+N vs Output Power
THD+N vs Output Power
THD+N vs Output Power
DS100005-9
DS100005-10
DS100005-11
THD+N vs Output Power
THD+N vs Output Power
THD+N vs Output Power
DS100005-12
DS100005-13
DS100005-14
Output Power vs
Supply Voltage
Output Power vs
Supply Voltage
Output Power vs
Supply Voltage
DS100005-15
DS100005-16
DS100005-17
5
www.national.com
Typical Performance Characteristics (Continued)
Power Dissipation vs
Output Power
Output Power vs
Load Resistance
Output Power vs
Load Resistance
DS100005-18
DS100005-21
DS100005-24
DS100005-19
DS100005-20
Power Dissipation vs
Output Power
Clipping Voltage vs
Supply Voltage
Clipping Voltage vs
Supply Voltage
DS100005-22
DS100005-23
Output Attenuation in
Shutdown Mode
Supply Current vs
Supply Voltage
Channel Separation
DS100005-26
DS100005-25
www.national.com
6
Typical Performance Characteristics (Continued)
Power Supply
Rejection Ratio
Open Loop
Frequency Response
Noise Floor
DS100005-27
DS100005-29
DS100005-28
Frequency Response vs
Output Capacitor Size
Frequency Response vs
Output Capacitor Size
Frequency Response vs
Output Capacitor Size
DS100005-30
DS100005-31
DS100005-32
Typical Application
Typical Application
Frequency Response
Frequency Response
Power Derating Curve
DS100005-33
DS100005-34
DS100005-35
7
www.national.com
POWER SUPPLY BYPASSING
Application Information
As with any power amplifer, proper supply bypassing is criti-
cal for low noise performance and high power supply rejec-
tion. The capacitor location on both the bypass and power
supply pins should be as close to the device as possible. As
displayed in the Typical Performance Characteristics sec-
tion, the effect of a larger half supply bypass capacitor is im-
proved low frequency PSRR due to increased half-supply
stability. Typical applications employ a 5V regulator with
10 µF and a 0.1 µF bypass capacitors which aid in supply
stability, but do not eliminate the need for bypassing the sup-
ply nodes of the LM4881. The selection of bypass capaci-
tors, especially CB, is thus dependent upon desired low fre-
quency PSRR, click and pop performance as explained in
the section, Proper Selection of External Components
section, system cost, and size constraints.
SHUTDOWN FUNCTION
In order to reduce power consumption while not in use, the
LM4881 contains a shutdown pin to externally turn off the
amplifier’s bias circuitry. This shutdown feature turns the am-
plifier off when a logic high is placed on the shutdown pin.
The trigger point between a logic low and logic high level is
typically half supply. It is best to switch between ground and
supply to provide maximum device performance. By switch-
ing the shutdown pin to the VDD, the LM4881 supply current
draw will be minimized in idle mode. While the device will be
disabled with shutdown pin voltages less than V DD, the idle
current may be greater than the typical value of 0.7 µA. In ei-
ther case, the shutdown pin should be tied to a definite volt-
age because leaving the pin floating may result in an un-
wanted shutdown condition. In many applications,
a
PROPER SELECTION OF EXTERNAL COMPONENTS
microcontroller or microprocessor output is used to control
the shutdown circuitry which provides a quick, smooth tran-
sition into shutdown. Another solution is to use a single-pole,
single-throw switch in conjunction with an external pull-up re-
sistor. When the switch is closed, the shutdown pin is con-
nected to ground and enables the amplifier. If the switch is
open, then the external pull-up resistor will disable the
LM4881. This scheme guarantees that the shutdown pin will
not float which will prevent unwanted state changes.
Selection of external components when using integrated
power amplifiers is critical to optimize device and system
performance. While the LM4881 is tolerant of external com-
ponent combinations, consideration to component values
must be used to maximize overall system quality.
The LM4881 is unity gain stable and this gives a designer
maximum system flexibility. The LM4881 should be used in
low gain configurations to minimize THD+N values, and
maximum the signal-to-noise ratio. Low gain configurations
require large input signals to obtain a given output power. In-
put signals equal to or greater than 1 Vrms are available
from sources such as audio codecs. Please refer to the sec-
tion, Audio Power Amplifier Design, for a more complete
explanation of proper gain selection.
POWER DISSIPATION
Power dissipation is a major concern when using any power
amplifier and must be thoroughly understood to ensure a
successful design. Equation 1 states the maximum power
dissipation point for a single-ended amplifier operating at a
given supply voltage and driving a specified output load.
2
Besides gain, one of the major considerations is the closed
loop bandwidth of the amplifier. To a large extent, the band-
width is dicated by the choice of external components shown
in Figure 1. Both the input coupling capacitor, Ci, and the out-
put coupling capacitor, Co, form first order high pass filters
which limit low frequency response. These values should be
chosen based on needed frequency response for a few dis-
tinct reasons.
PDMAX = (VDD
)
/ (2π2RL)
(1)
Since the LM4881 has two operational amplifiers in one
package, the maximum internal power dissipation point is
twice that of the number which results from Equation 1. Even
with the large internal power dissipation, the LM4881 does
not require heat sinking over a large range of ambient tem-
perature. From Equation 1, assuming a 5V power supply and
an 8Ω load, the maximum power dissipation point is 158 mW
per amplifier. Thus the maximum package dissipation point
is 317 mW. The maximum power dissipation point obtained
must not be greater than the power dissipation that results
from Equation 2:
Selection of Input and Output Capacitor Size
Large input and output capacitors are both expensive and
space hungry for portable designs. Clearly a certain sized
capacitor is needed to couple in low frequencies without se-
vere attenuation. But in many cases the speakers used in
portable systems, whether internal or external, have little
ability to reproduce signals below 150 Hz. Thus using large
input and output capacitors may not increase system perfor-
mance.
PDMAX = (TJMAX − TA) / θJA
For package MUA08A, θJA = 230˚C/W, and for package
M08A, θJA = 170˚C/W, and for package N08E,
(2)
θ
=
JA
107˚C/W. TJMAX = 150˚C for the LM4881. Depending on the
ambient temperature, TA, of the system surroundings, Equa-
tion 2 can be used to find the maximum internal power dissi-
pation supported by the IC packaging. If the result of Equa-
tion 1 is greater than that of Equation 2, then either the
supply voltage must be decreased, the load impedance in-
creased or TA reduced. For the typical application of a 5V
power supply, with an 8Ω load, the maximum ambient tem-
perature possible without violating the maximum junction
temperature is approximately 96˚C provided that device op-
eration is around the maximum power dissipation point.
Power dissipation is a function of output power and thus, if
typical operation is not around the maximum power dissipa-
tion point, the ambient temperature may be increased ac-
cordingly. Refer to the Typical Performance Characteris-
tics curves for power dissipation information for lower output
powers.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
Ci. A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 VDD). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the ca-
pacitor size based on necessary low frequency response,
turn on pops can be minimized.
Besides minimizing the input and output capacitor sizes,
careful consideration should be paid to the bypass capacitor
value. Bypass capacitor CB is the most critical component to
minimize turn on pops since it determines how fast the
LM4881 turns on. The slower the LM4881’s outputs ramp to
their quiescent DC voltage (nominally 1/2 VDD), the smaller
the turn on pop. Thus choosing CB equal to 1.0 µF along with
a small value of Ci (in the range of 0.1 µF to 0.39 µF), the
www.national.com
8
dissipation point from Equation 1 must be multiplied by two
since there are two independent amplifiers inside the pack-
age.
Application Information (Continued)
shutdown function should be virtually clickless and popless.
While the device will function properly, (no oscillations or mo-
torboating), with C B equal to 0.1 µF, the device will be much
more susceptible to turn on clicks and pops. Thus, a value of
CB equal to 0.1 µF or larger is recommended in all but the
most cost sensitive designs.
Once the power dissipation equations have been addressed,
the required gain can be determined from Equation 4.
(4)
AV = Rf/Ri
(5)
AUDIO POWER AMPLIFIER DESIGN
From Equation 4, the minimum gain is: AV = 1.26
Since the desired input impedance was 20 kΩ, and with a
gain of 1.26, a value of 27 kΩ is designated for Rf, assuming
5% tolerance resistors. This combination results in a nominal
gain of 1.35. The final design step is to address the band-
width requirements which must be stated as a pair of −3 dB
frequency points. Five times away from a −3 dB point is
0.17 dB down from passband response assuming a single
pole roll-off. As stated in the External Components section,
both Ri in conjunction with C i, and Co with RL, create first or-
der highpass filters. Thus to obtain the desired frequency low
Design a Dual 200mW/8Ω Audio Amplifier
Given:
Power Output
Load Impedance
Input Level
200 mWrms
8Ω
1 Vrms (max)
20 kΩ
Input Impedance
Bandwidth
±
100 Hz–20 kHz 0.50 dB
A designer must first determine the needed supply rail to ob-
tain the specified output power. Calculating the required sup-
ply rail involves knowing two parameters, VOPEAK and also
the dropout voltage. The latter is typically 530 mV and can
be found from the graphs in the Typical Performance Char-
acteristics. VOPEAK can be determined from Equation 3.
±
response of 100 Hz within 0.5 dB, both poles must be
taken into consideration. The combination of two single order
filters at the same frequency forms a second order response.
This results in a signal which is down 0.34 dB at five times
away from the single order filter −3 dB point. Thus, a fre-
quency of 20 Hz is used in the following equations to ensure
that the response is better than 0.5 dB down at 100 Hz.
Ci ≥ 1 / (2π * 20 kΩ * 20 Hz) = 0.397 µF; use 0.39 µF.
Co ≥ 1 / (2π * 8Ω * 20 Hz) = 995 µF; use 1000 µF.
(3)
For 200 mW of output power into an 8Ω load, the required
V
OPEAK is 1.79 volts. A minimum supply rail of 2.32V results
The high frequency pole is determined by the product of the
desired high frequency pole, fH, and the closed-loop gain, A
from adding VOPEAK and VOD. Since 5V is a standard supply
voltage in most applications, it is chosen for the supply rail.
Extra supply voltage creates headroom that allows the
LM4881 to reproduce peaks in excess of 200 mW without
clipping the signal. At this time, the designer must make sure
that the power supply choice along with the output imped-
ance does not violate the conditions explained in the Power
Dissipation section. Remember that the maximum power
V. With a closed-loop gain of 1.35 and fH = 100 kHz, the re-
sulting GBWP = 135 kHz which is much smaller than the
LM4881 GBWP of 18 MHz. This figure displays that if a de-
signer has a need to design an amplifier with a higher gain,
the LM4881 can still be used without running into bandwidth
limitations.
9
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Order Number LM4881MM
NS Package Number MUA08A
Order Number LM4881M
NS Package Number M08A
www.national.com
10
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Order Number LM4881N
NS Package Number N08E
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
Email: sea.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号：
LM48820TM/NOPB
IC 0.095 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA14, ROHS COMPLIANT, MICRO SMD-14, Audio/Video Amplifier
NSC
LM48821
Direct Coupled, Ultra Low Noise, 52mW Differential Input Stereo Headphone Amplifier with I2C Volume Control
NSC
©2020 ICPDF网 联系我们和版权申明