LM75BIMMX-5 [NSC]
Digital Temperature Sensor and Thermal WATCHDOG? with Two-Wire Interface; 数字温度传感器和热看门狗？带双线接口
| 型号： | LM75BIMMX-5 |
| 厂家： | 
National Semiconductor |
| 描述： | Digital Temperature Sensor and Thermal WATCHDOG? with Two-Wire Interface |
| 文件： | 总18页 (文件大小：353K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
February 2004
LM75
Digital Temperature Sensor and Thermal Watchdog with
Two-Wire Interface
n Register readback capability
n Power up defaults permit stand-alone operation as
General Description
The LM75 is a temperature sensor, Delta-Sigma analog-to-
thermostat
digital converter, and digital over-temperature detector with
n Shutdown mode to minimize power consumption
n Up to 8 LM75s can be connected to a single bus
n UL Recognized Component
I2C® interface. The host can query the LM75 at any time to
read temperature. The open-drain Overtemperature Shut-
down (O.S.) output becomes active when the temperature
exceeds a programmable limit. This pin can operate in either
“Comparator” or “Interrupt” mode.
Key Specifications
The host can program both the temperature alarm threshold
(TOS) and the temperature at which the alarm condition goes
away (THYST). In addition, the host can read back the con-
tents of the LM75’s TOS and THYST registers. Three pins (A0,
A1, A2) are available for address selection. The sensor
powers up in Comparator mode with default thresholds of
j
Supply Voltage
3.0V to 5.5V
250 µA (typ)
1 mA (max)
4 µA (typ)
2˚C(max)
j
Supply Current
operating
shutdown
j
Temperature Accuracy −25˚C to 100˚C
−55˚C to 125˚C
80˚C TOS and 75˚C THYST
.
3˚C(max)
The LM75’s 3.0V to 5.5V supply voltage range, low supply
current and I2C interface make it ideal for a wide range of
applications. These include thermal management and pro-
tection applications in personal computers, electronic test
equipment, and office electronics.
Applications
n System Thermal Management
n Personal Computers
n Office Electronics
Features
n Electronic Test Equipment
n SOP-8 and Mini SOP-8 (MSOP) packages save space
n I2C Bus interface
n Separate open-drain output pin operates as interrupt or
comparator/thermostat output
Simplified Block Diagram
01265801
2
I
C® is a registered trademark of Philips Corporation.
© 2004 National Semiconductor Corporation
DS012658
www.national.com
Connection Diagram
Ordering Information
SOP-8 and Mini SOP-8
01265802
Noise Filter
on SDA and
SCL
Package
Order Number
NS Package
Number
Supply
Voltage
Transport Media
95 Units in Rail
Marking
LM75BIM-3
LM75BIM-3
LM75BIM-3
T01B
M08A (SOP-8)
M08A (SOP-8)
3.3V
3.3V
3.3V
3.3V
5V
Yes
LM75BIMX-3
LM75BIMM-3
LM75BIMMX-3
LM75BIM-5
2500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
95 Units in Rail
Yes
MUA08A (MSOP-8)
MUA08A (MSOP-8)
M08A (SOP-8)
Yes
T01B
Yes
LM75BIM-5
LM75BIM-5
T00B
Yes
LM75BIMX-5
LM75BIMM-5
LM75BIMMX-5
LM75CIM-3
M08A (SOP-8)
5V
2500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
95 Units in Rail
Yes
MUA08A (MSOP-8)
MUA08A (MSOP-8)
M08A (SOP-8)
5V
Yes
T00B
5V
Yes
LM75CIM-3
LM75CIM-3
T01C
3.3V
3.3V
3.3V
3.3V
5V
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
LM75CIMX-3
LM75CIMM-3
LM75CIMMX-3
LM75CIM-5
M08A (SOP-8)
2500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
95 Units in Rail
MUA08A (MSOP-8)
MUA08A (MSOP-8)
M08A (SOP-8)
T01C
LM75CIM-5
LM75CIM-5
T00C
LM75CIMX-5
LM75CIMM-5
LM75CIMMX-5
M08A (SOP-8)
5V
2500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
MUA08A (MSOP-8)
MUA08A (MSOP-8)
5V
T00C
5V
Pin Description
#
Label
SDA
Pin
1
Function
Typical Connection
I2C Serial Bi-Directional Data Line. Open Drain.
I2C Clock Input
From Controller, tied to a pull-up
From Controller
SCL
O.S.
GND
+VS
2
3
Overtemperature Shutdown Open Drain Output
Power Supply Ground
Pull–up Resistor, Controller Interrupt Line
Ground
4
8
Positive Supply Voltage Input
DC Voltage from 3V to 5.5V; 0.1µF bypass
capacitor with 10µF bulk capacitance in the
near vicinity
A0–A2
7,6,5
User-Set I2C Address Inputs
Ground (Low, “0”) or +VS (High, “1”)
www.national.com
2
Pin Description (Continued)
01265803
FIGURE 1. Typical Application
3
www.national.com
Absolute Maximum Ratings (Note 1)
ESD Susceptibility (Note 4)
Human Body Model
Machine Model
LM75B LM75C
2500V
250V
1500V
100V
Supply Voltage
−0.3V to 6.5V
−0.3V to +VS + 0.3V
5 mA
Voltage at any Pin
Input Current at any Pin (Note 2)
Package Input Current (Note 2)
O.S. Output Sink Current
O.S. Output Voltage
Operating Ratings
Specified Temperature Range
20 mA
10 mA
TMIN to TMAX
−55˚C to +125˚C
+3.0V to +5.5V
6.5V
(Note 5)
Storage Temperature
−65˚C to +150˚C
Supply Voltage Range (+VS)
Soldering Information, Lead Temperature
SOP and MSOP Package (Note 3)
Vapor Phase (60 seconds)
215˚C
220˚C
Infrared (15 seconds)
Temperature-to-Digital Converter Characteristics
Unless otherwise noted, these specifications apply for +VS = +5 Vdc for LM75BIM-5, LM75BIMM-5, LM75CIM-5, and
LM75CIMM-5 and +VS = +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3, and LM75CIMM-3 (Note 6). Boldface limits
apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise noted.
Typical
(Note 12)
Limits
(Note 7)
2.0
Units
(Limit)
˚C (max)
˚C (max)
Bits
Parameter
Conditions
Accuracy
TA = −25˚C to +100˚C
TA = −55˚C to +125˚C
3.0
Resolution
9
100
0.25
4
Temperature Conversion Time
Quiescent Current LM75B
(Note 8)
ms
I2C Inactive
0.5
1.0
0.8
mA (max)
µA
Shutdown Mode, +VS = 3V
Shutdown Mode, +VS = 5V
I2C Inactive
6
µA
LM75C
0.25
4
mA (max)
µA
Shutdown Mode, +VS = 3V
Shutdown Mode, +VS = 5V
IOUT = 4.0 mA
6
µA
O.S. Output Saturation Voltage
O.S. Delay
V (max)
(Note 9)
(Note 10)
1
6
Conversions (min)
Conversions (max)
TOS Default Temperature
THYST Default Temperature
(Note 11)
(Note 11)
80
75
˚C
˚C
Logic Electrical Characteristics
DIGITAL DC CHARACTERISTICS Unless otherwise noted, these specifications apply for +VS = +5 Vdc for LM75BIM-5,
LM75BIMM-5, LM75CIM-5, and LM75CIMM-5 and +VS = +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3, and
LM75CIMM-3 (Note 6). Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise
noted.
Typical
(Note 12)
Limits
(Note 7)
+VS x 0.7
+VS + 0.5
−0.3
Units
(Limit)
Symbol
Parameter
Conditions
VIN(1)
Logical “1” Input Voltage
V (min)
V (max)
V (min)
V (max)
µA (max)
µA (max)
pF
VIN(0)
Logical “0” Input Voltage
+VS x 0.3
1.0
IIN(1)
IIN(0)
CIN
Logical “1” Input Current
Logical “0” Input Current
All Digital Inputs
VIN = 5V
0.005
−0.005
20
VIN = 0V
−1.0
IOH
High Level Output Current
Low Level Output Voltage
Output Fall Time
VOH = 5V
100
0.4
µA (max)
V (max)
ns (max)
VOL
tOF
IOL = 3 mA
CL = 400 pF
250
www.national.com
4
Logic Electrical Characteristics (Continued)
DIGITAL DC CHARACTERISTICS Unless otherwise noted, these specifications apply for +VS = +5 Vdc for LM75BIM-5,
LM75BIMM-5, LM75CIM-5, and LM75CIMM-5 and +VS = +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3, and
LM75CIMM-3 (Note 6). Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise
noted.
Typical
(Note 12)
Limits
(Note 7)
Units
(Limit)
Symbol
Parameter
Conditions
IO = 3 mA
I2C DIGITAL SWITCHING CHARACTERISTICS Unless otherwise noted, these specifications apply for +VS = +5 Vdc for
LM75BIM-5, LM75BIMM-5, LM75CIM-5, and LM75CIMM-5 and +VS = +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3,
and LM75CIMM-3. CL (load capacitance) on output lines = 80 pF unless otherwise specified. Boldface limits apply for TA
TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise noted. The switching characteristics of the LM75 fully
=
meet or exceed the published specifications of the I2C bus. The following parameters are the timing relationships between SCL
and SDA signals related to the LM75. They are not the I2C bus specifications.
Typical
(Note 12)
Limits
(Note 7)
2.5
Units
(Limit)
Symbol
t1
Parameter
Conditions
SCL (Clock) Period
µs (min)
ns (min)
ns (min)
ns (min)
ns (min)
ms (min)
ms (max)
t2
t3
t4
t5
Data in Set-Up Time to SCL High
100
Data Out Stable after SCL Low
0
SDA Low Set-Up Time to SCL Low (Start Condition)
SDA High Hold Time after SCL High (Stop Condition)
100
100
tTIMEOUT SDA Time Low for Reset of Serial Interface (Note 13)
LM75B
LM75C
75
325
Not
Applicable
01265804
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions.
<
>
+V ) the current at that pin should be limited to 5 mA. The 20 mA
Note 2: When the input voltage (V ) at any pin exceeds the power supplies (V
GND or V
I
I
I
S
maximum package input current rating limits the number of pins that can safely exceedthe power supplies with an input current of 5 mA to four.
Note 3: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National
Semiconductor Linear Data Book for other methods of soldering surface mount devices.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin.
5
www.national.com
Note 5: LM75 θ (thermal resistance, junction-to-ambient) when attached to a printed circuit board with 2 oz. foil similar to the one shown in Figure 3 is summarized
JA
in the table below:
NS Package
Number
M08A
Thermal
Resistance (θJA
200˚C/W
Device Number
)
LM75BIM-3, LM75BIM-5, LM75CIM-3, LM75CIM-5
LM75BIMM-3, LM75BIMM-5, LM75CIMM-3, LM75CIMM-5
MUA08A
250˚C/W
Note 6: All part numbers of the LM75 will operate properly over the +V supply voltage range of 3V to 5.5V. The devices are tested and specified for rated accuracy
S
at their nominal supply voltage. Accuracy will typically degrade 1˚C/V of variation in +V as it varies from the nominal value.
S
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: This specification is provided only to indicate how often temperature data is updated. The LM75 can be read at any time without regard to conversion state
(and will yield last conversion result). If a conversion is in process it will be interrupted and restarted after the end of the read.
Note 9: For best accuracy, minimize output loading. Higher sink currents can affect sensor accuracy with internal heating. This can cause an error of 0.64˚C at full
rated sink current and saturation voltage based on junction-to-ambient thermal resistance.
Note 10: O.S. Delay is user programmable up to 6 “over limit” conversions before O.S. is set to minimize false tripping in noisy environments.
Note 11: Default values set at power up.
Note 12: Typicals are at T = 25˚C and represent most likely parametric norm.
A
Note 13: Holding the SDA line low for a time greater than t
will cause the LM75B to reset SDA to the IDLE state of the serial bus communication (SDA set
TIMEOUT
High).
01265805
FIGURE 2. Temperature-to-Digital Transfer Function (Non-linear scale for clarity)
www.national.com
6
01265806
FIGURE 3. Printed Circuit Board Used for Thermal Resistance Specifications
Typical Performance Characteristics
Static Quiescent Current vs
Temperature
Dynamic Quiescent Current vs
Temperature
Accuracy vs Temperature
01265816
01265817
01265818
2. The LM75B also has a bus fault timeout feature. If the
SDA line is held low for longer than tTIMEOUT (75 ms
minimum to 325 ms maximum) the LM75B will reset to
the IDLE state (SDA set to high impedance) and wait for
a new start condition.
1.0 Functional Description
The LM75 temperature sensor incorporates a band-gap type
temperature sensor and 9-bit ADC (Delta-Sigma Analog-to-
Digital Converter). The temperature data output of the LM75
is available at all times via the I2C bus. If a conversion is in
progress, it will be stopped and restarted after the read. A
digital comparator is also incorporated that compares a se-
ries of readings, the number of which is user-selectable, to
user-programmable setpoint and hysteresis values. The
comparator trips the O.S. output line, which is programmable
for mode and polarity.
1.1 O.S. OUTPUT, TOS AND THYST LIMITS
In Comparator mode the O.S. Output behaves like a ther-
mostat. The output becomes active when temperature ex-
ceeds the TOS limit, and leaves the active state when the
temperature drops below the THYST limit. In this mode the
O.S. output can be used to turn a cooling fan on, initiate an
emergency system shutdown, or reduce system clock
speed. Shutdown mode does not reset O.S. state in a com-
parator mode.
The LM75B contains all the functionality of the LM75C, plus
two additional features:
1. The LM75B has an integrated low-pass filter on both the
SDA and the SCL line. These filters increase communi-
cations reliability in noisy environments.
In Interrupt mode exceeding TOS also makes O.S. active but
O.S. will remain active indefinitely until reset by reading any
register via the I2C interface. Once O.S. has been activated
7
www.national.com
above the nominal 1.7V power up threshold, the internal
registers are reset to the power up default values listed
above.
1.0 Functional Description (Continued)
by crossing TOS, then reset, it can be activated again only by
Temperature going below THYST. Again, it will remain active
indefinitely until being reset by a read. Placing the LM75 in
shutdown mode also resets the O.S. Output.
1.3 I2C BUS INTERFACE
The LM75 operates as a slave on the I2C bus, so the SCL
line is an input (no clock is generated by the LM75) and the
SDA line is a bi-directional serial data path. According to I2C
bus specifications, the LM75 has a 7-bit slave address. The
four most significant bits of the slave address are hard wired
inside the LM75 and are “1001”. The three least significant
bits of the address are assigned to pins A2–A0, and are set
by connecting these pins to ground for a low, (0); or to +VS
for a high, (1).
1.2 POWER UP AND POWER DOWN
The LM75 always powers up in a known state. The power up
default conditions are:
1. Comparator mode
2. TOS = 80˚C
3. THYST = 75˚C
4. O.S. active low
5. Pointer = “00”
If the LM75 is not connected to the I2C bus on power up, it
will act as a stand-alone thermostat with the above tempera-
ture settings.
Therefore, the complete slave address is:
1
0
0
1
A2
A1
A0
MSB
LSB
When the supply voltage is less than about 1.7V, the LM75 is
considered powered down. As the supply voltage rises
01265807
Note 14: These interrupt mode resets of O.S. occur only when LM75 is read or placed in shutdown. Otherwise, O.S. would remain active indefinitely for any event.
FIGURE 4. O.S. Output Temperature Response Diagram
www.national.com
8
1.7 COMPARATOR/INTERRUPT MODE
1.0 Functional Description (Continued)
1.4 TEMPERATURE DATA FORMAT
As indicated in the O.S. Output Temperature Response Dia-
gram, Figure 4, the events that trigger O.S. are identical for
either Comparator or Interrupt mode. The most important
difference is that in Interrupt mode the O.S. will remain set
indefinitely once it has been set. To reset O.S. while in
Interrupt mode, perform a read from any register in the
LM75.
Temperature data can be read from the Temperature, TOS
Set Point, and THYST Set Point registers; and written to the
TOS Set Point, and THYST Set Point registers. Temperature
data is represented by a 9-bit, two’s complement word with
an LSB (Least Significant Bit) equal to 0.5˚C:
Temperature
Digital Output
Binary
1.8 O.S. OUTPUT
Hex
0FAh
032h
001h
000h
1FFh
1CEh
192h
The O.S. output is an open-drain output and does not have
an internal pull-up. A “high” level will not be observed on this
pin until pull-up current is provided from some external
source, typically a pull-up resistor. Choice of resistor value
depends on many system factors but, in general, the pull-up
resistor should be as large as possible. This will minimize
any errors due to internal heating of the LM75. The maxi-
mum resistance of the pull up, based on LM75 specification
for High Level Output Current, to provide a 2V high level, is
30 kΩ.
+125˚C
+25˚C
+0.5˚C
0˚C
0 1111 1010
0 0011 0010
0 0000 0001
0 0000 0000
1 1111 1111
1 1100 1110
1 1001 0010
−0.5˚C
−25˚C
−55˚C
1.9 O.S. POLARITY
1.5 SHUTDOWN MODE
The O.S. output can be programmed via the configuration
register to be either active low (default mode), or active high.
In active low mode the O.S. output goes low when triggered
exactly as shown on the O.S. Output Temperature Response
Diagram, Figure 4. Active high simply inverts the polarity of
the O.S. output.
Shutdown mode is enabled by setting the shutdown bit in the
Configuration register via the I2C bus. Shutdown mode re-
duces power supply current to 4 µA typical. In Interrupt mode
O.S. is reset if previously set and is undefined in Comparator
mode during shutdown. The I2C interface remains active.
Activity on the clock and data lines of the I2C bus may
slightly increase shutdown mode quiescent current. TOS
,
THYST, and Configuration registers can be read from and
written to in shutdown mode.
1.6 FAULT QUEUE
A fault queue of up to 6 faults is provided to prevent false
tripping of O.S. when the LM75 is used in noisy environ-
ments. The number of faults set in the queue must occur
consecutively to set the O.S. output.
9
www.national.com
1.0 Functional Description (Continued)
1.10 INTERNAL REGISTER STRUCTURE
01265808
There are four data registers in the LM75, selected by the
Pointer register. At power-up the Pointer is set to “00”; the
location for the Temperature Register. The Pointer register
latches whatever the last location it was set to. In Interrupt
Mode, a read from the LM75, or placing the device in shut-
down mode, resets the O.S. output. All registers are read
and write, except the Temperature register which is read
only.
The first data byte is the most significant byte with most
significant bit first, permitting only as much data as neces-
sary to be read to determine temperature condition. For
instance, if the first four bits of the temperature data indi-
cates an overtemperature condition, the host processor
could immediately take action to remedy the excessive tem-
peratures. At the end of a read, the LM75 can accept either
Acknowledge or No Acknowledge from the Master (No Ac-
knowledge is typically used as a signal for the slave that the
Master has read its last byte).
A write to the LM75 will always include the address byte and
the Pointer byte. A write to the Configuration register re-
quires one data byte, and the TOS and THYST registers
require two data bytes.
An inadvertent 8-bit read from a 16-bit register, with the D7
bit low, can cause the LM75 to stop in a state where the SDA
line is held low as shown in Figure 5. This can prevent any
further bus communication until at least 9 additional clock
cycles have occurred. Alternatively, the master can issue
clock cycles until SDA goes high, at which time issuing a
“Stop” condition will reset the LM75.
Reading the LM75 can take place either of two ways: If the
location latched in the Pointer is correct (most of the time it is
expected that the Pointer will point to the Temperature reg-
ister because it will be the data most frequently read from the
LM75), then the read can simply consist of an address byte,
followed by retrieving the corresponding number of data
bytes. If the Pointer needs to be set, then an address byte,
pointer byte, repeat start, and another address byte will
accomplish a read.
01265809
FIGURE 5. Inadvertent 8-Bit Read from 16-Bit Register where D7 is Zero (“0”)
www.national.com
10
1.0 Functional Description (Continued)
1.11 POINTER REGISTER
(Selects which registers will be read from or written to):
P7
P6
P5
P4
P3
P2
P1
Register
Select
P0
0
0
0
0
0
0
P0-P1: Register Select:
P1
0
P0
Register
0
1
0
1
Temperature (Read only) (Power-up default)
Configuration (Read/Write)
THYST (Read/Write)
0
1
1
TOS (Read/Write)
P2–P7: Must be kept zero.
1.12 TEMPERATURE REGISTER
(Read Only):
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MSB Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
X
X
X
X
X
X
X
D0–D6: Undefined
D7–D15: Temperature Data. One LSB
complement format.
=
0.5˚C. Two’s
1.13 CONFIGURATION REGISTER
(Read/Write):
D7
D6
D5
D4
D3
D2
D1
Cmp/Int
D0
Shutdown
0
0
0
Fault Queue
O.S.
Polarity
Power up default is with all bits “0” (zero).
D3–D4: Fault Queue: Number of faults necessary to detect
before setting O.S. output to avoid false tripping due to
noise. Faults are determind at the end of a conversion.
Conversions take about 100 ms, typically, to complete.
D0: Shutdown: When set to 1 the LM75 goes to low power
shutdown mode.
D1: Comparator/Interrupt mode: 0 is Comparator mode, 1 is
Interrupt mode.
D2: O.S. Polarity: 0 is active low, 1 is active high. O.S. is an
open-drain output under all conditions.
D4
0
D3
0
Number of Faults
1 (Power-up default)
0
1
2
4
6
1
0
1
1
D5–D7: These bits are used for production testing and must
be kept zero for normal operation.
1.14 THYST AND TOS REGISTER
(Read/Write):
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MSB Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
X
X
X
X
X
X
X
D0–D6: Undefined
D7–D15: THYST Or TOS Trip Temperature Data. Power up
default is TOS = 80˚C, THYST = 75˚C.
11
www.national.com
www.national.com
12
13
www.national.com
DIGITAL NOISE ISSUES
3.0 Application Hints
The LM75B features an integrated low-pass filter on both the
SCL and the SDA digital lines to mitigate the effects of bus
noise. Although this filtering makes the LM75B communica-
tion robust in noisy environments, good layout practices are
always recommended. Minimize noise coupling by keeping
digital traces away from switching power supplies. Also,
ensure that digital lines containing high-speed data commu-
nications cross at right angles to the SDA and SCL lines.
To get the expected results when measuring temperature
with an integrated circuit temperature sensor like the LM75,
it is important to understand that the sensor measures its
own die temperature. For the LM75, the best thermal path
between the die and the outside world is through the LM75’s
pins. In the MSOP-8 package, the GND pin is directly con-
nected to the die, so the GND pin provides the best thermal
path. If the other pins are at different temperatures (unlikely,
but possible), they will affect the die temperature, but not as
strongly as the GND pin. In the SO-8 package, none of the
pins is directly connected to the die, so they will all contribute
similarly to the die temperature. Because the pins represent
a good thermal path to the LM75 die, the LM75 will provide
an accurate measurement of the temperature of the printed
circuit board on which it is mounted. There is a less efficient
thermal path between the plastic package and the LM75 die.
If the ambient air temperature is significantly different from
the printed circuit board temperature, it will have a small
effect on the measured temperature.
Excessive noise coupling into the SDA and SCL lines on the
LM75C—specifically noise with amplitude greater than 400
mVpp (the LM75’s typical hysteresis), overshoot greater than
300 mV above +Vs, and undershoot more than 300 mV
below GND—may prevent successful serial communication
with the LM75C. Serial bus no-acknowledge is the most
common symptom, causing unnecessary traffic on the bus.
The layout procedures mentioned above apply also to the
LM75C. Although the serial bus maximum frequency of com-
munication is only 100 kHz, care must be taken to ensure
proper termination within a system with long printed circuit
board traces or multiple parts on the bus. Resistance can be
added in series with the SDA and SCL lines to further help
filter noise and ringing. A 5 kΩ resistor should be placed in
series with the SCL line, placed as close as possible to the
SCL pin on the LM75C. This 5 kΩ resistor, with the 5 pF to 10
pF stray capacitance of the LM75 provides a 6 MHz to 12
MHz low pass filter, which is sufficient filtering in most cases.
In probe-type applications, the LM75 can be mounted inside
a sealed-end metal tube, and can then be dipped into a bath
or screwed into a threaded hole in a tank. As with any IC, the
LM75 and accompanying wiring and circuits must be kept
insulated and dry, to avoid leakage and corrosion. This is
especially true if the circuit may operate at cold temperatures
where condensation can occur. Printed-circuit coatings and
varnishes such as Humiseal and epoxy paints or dips are
often used to insure that moisture cannot corrode the LM75
or its connections.
4.0 Typical Applications
01265812
When using the two-wire interface: program O.S. for active high and connect O.S. directly to Q2’s gate.
FIGURE 8. Simple Fan Controller, Interface Optional
www.national.com
14
4.0 Typical Applications (Continued)
01265813
FIGURE 9. Data Acquisition System with Temperature Input via I2C Bus
01265814
FIGURE 10. Simple Thermostat, Interface Optional
15
www.national.com
4.0 Typical Applications (Continued)
01265815
FIGURE 11. Temperature Sensor with Loudmouth Alarm (Barking Watchdog)
www.national.com
16
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead (0.150" Wide) Molded Small Outline Package (SOP), JEDEC
Order Number LM75CIM-3, LM75CIMX-3, LM75CIM-5, LM75CIMX-5,
LM75BIM-3, LM75BIMX-3, LM75BIM-5, or LM75BIMX-5
NS Package Number M08A
17
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8-Lead Molded Mini Small Outline Package (MSOP)
(JEDEC REGISTRATION NUMBER M0-187)
Order Number LM75CIMM-3, LM75CIMMX-3,
LM75CIMM-5, LM75CIMMX-5,
LM75BIMM-3, LM75BIMMX-3,
LM75BIMM-5, or LM75BIMMX-5
NS Package Number MUA08A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号：
LM75BIMMX-5/NOPB
DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 3Cel, SQUARE, SURFACE MOUNT, MO-187, MSOP-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明