LMV7235M5 [NSC]
45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output; 为45nS ,超低功耗,低电压轨至轨输入比较器具有漏极开路/推挽输出型号: | LMV7235M5 |
厂家: | National Semiconductor |
描述: | 45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output |
文件: | 总12页 (文件大小:323K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
February 2002
LMV7235/LMV7239
45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input
Comparator with Open-Drain/Push-Pull Output
General Description
Features
The LMV7235/39 are ultra low power, low voltage, 45ns
comparators. They are guaranteed to operate over the full
supply voltage range of 2.7V to 5V. These devices achieve a
45ns propagation delay while consuming only 65µA of sup-
ply current at 5V.
(VS = 5V, TA = 25˚C, Typical values unless otherwise speci-
fied)
n Propagation delay
n Low supply current
n Rail-to-Rail input
45ns
65µA
The LMV7235/39 have a greater than rail-to-rail common
mode voltage range. The input common mode voltage range
extends 200mV below ground and 200mV above supply,
allowing both ground and supply sensing.
n Open drain and push-pull output
n Ideal for 2.7V and 5V single supply applications
n Available in space saving packages: 5-pin SOT23-5
and 5-pin SC70-5
The LMV7235 features an open drain output. By connecting
an external resistor, the output of the comparator can be
used as a level shifter.
Applications
n Portable and battery powered systems
n Scanners
The LMV7239 features a push-pull output stage. This feature
allows operation without the need of an external pull-up
resistor.
n Set top boxes
n High speed differential line receiver
n Window comparators
n Zero-crossing detectors
n High speed sampling circuits
The LMV7235/39 are available in the SC70-5 and SOT23-5
packages, which are ideal for systems where small size and
low power is critical.
Typical Application
10135902
© 2002 National Semiconductor Corporation
DS101359
www.national.com
Connection Diagram
SC70-5/SOT23-5
10135903
Top View
Ordering Information
Package
Part Number
LMV7235M7
LMV7235M7X
LMV7239M7
LMV7239M7X
LMV7235M5
LMV7235M5X
LMV7239M5
LMV7239M5X
Marking
C21
Supplied as
NSC Drawing
1k Units Tape and Reel
3k Units Tape and Reel
1k Units Tape and Reel
3k Units Tape and Reel
1k Units Tape and Reel
3k Units Tape and Reel
1k Units Tape and Reel
3k Units Tape and Reel
5-pin SC70-5
C21
MAA05A
C20
C20
C21A
C21A
C20A
C20A
5-pin SOT23-5
MF05A
Simplified Schematic
10135901
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Voltage at Input/Output Pins
Current at Input Pin (Note 9)
(V+) +0.3V
(V−) −0.3V
±
10mA
ESD Tolerance (Note 2)
Operating Ratings
Machine Body
100V
1000V
Supply Voltages (V+ - V−)
Junction Temperature Range
(Note 4)
2.7V to 5V
Human Model Body
−40˚C to +85˚C
±
Differential Input Voltage
Output Short Circuit Duration
Supply Voltage (V+ - V−)
Soldering Information
Supply Voltage
(Note 3)
Storage Temperature Range
Package Thermal Resistance
SC70-5
−65˚C to +150˚C
5.5V
478˚C/W
265˚C/W
Infrared or Convection (20 sec)
Wave Soldering (10 sec)
235˚C
SOT23-5
260˚C (lead temp)
2.7V Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25˚C, VCM = V+/2, V+ = 2.7V, V− = 0V−. Boldface limits apply at the
temperature extremes.
Symbol
VOS
Parameter
Input Offset Voltage
Conditions
Typ
(Note 5)
0.8
Limits
(Note 6)
6
Units
mV
max
nA
8
IB
Input Bias Current
30
5
400
600
200
400
52
max
nA
IOS
Input Offset Current
max
dB
<
<
CMRR
PSRR
VCM
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Input Common-Mode Voltage Range
0V VCM 2.7V
62
(Note 7)
min
dB
V+ = 2.7V to 5V
85
65
min
V
V+ +0.2
−0.2
V+ −0.26
V+ −0.02
230
V+ +0.1
V+
>
CMRR 50dB
min
V
−0.1
0
max
V
VO
Output Swing High
(LMV7239 only)
IL = 4mA,
V+ −0.35
VID = 500mV
IL = 0.4mA,
min
V
VID = 500mV
IL = −4mA,
min
mV
max
mV
max
mA
Output Swing Low
350
(LMV7239/LMV7235)
VID = −500mV
IL = −0.4mA,
450
15
VID = −500mV
Sourcing, VO = 0V
(LMV7239 only)
(Note 3)
ISC
Output Short Circuit Current
15
Sinking, VO = 2.7V
(LMV7235 RL = 10k) (Note 3)
No load
20
52
mA
IS
Supply Current
85
µA
100
max
3
www.national.com
2.7V Electrical Characteristics (Continued)
Unless otherwise specified, all limits guaranteed for TJ = 25˚C, VCM = V+/2, V+ = 2.7V, V− = 0V−. Boldface limits apply at the
temperature extremes.
Symbol
tPD
Parameter
Propagation Delay
Conditions
Overdrive = 20mV
Typ
(Note 5)
68
Limits
Units
ns
(Note 6)
(Note 10)
Overdrive = 50mV
(Note 10)
63
50
5
ns
Overdrive = 100mV
(Note 10)
ns
tSKEW
tr
Propagation Delay Skew
(LMV7239 only)
(Note 8)
ns
Output Rise Time
LMV7239
1.7
112
ns
10% to 90%
LMV7235
ns
10% to 90%
(Note 10)
tf
Output Fall Time
90% to 10%
1.7
3
ns
ILEAKAGE
Output Leakage Current
(LMV7235 only)
nA
5V Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25˚C, VCM = V+/2, V+ = 5V, V− = 0V. Boldface limits apply at the
temperature extremes.
Symbol
VOS
Parameter
Input Offset Voltage
Conditions
Typ
(Note 5)
1
Limits
(Note 6)
6
Units
mV
max
nA
8
IB
Input Bias Current
30
5
400
600
200
400
52
max
nA
IOS
Input Offset Current
max
dB
<
<
CMRR
PSRR
VCM
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Input Common-Mode Voltage Range
0V VCM 5V
67
min
dB
V+ = 2.7V to 5V
85
65
min
V
V+ +0.2
−0.2
V+ −0.15
V+ −0.01
230
V+ +0.1
V+
>
CMRR 50dB
min
V
−0.1
0
max
V
VO
Output Swing High
(LMV7239 only)
IL = 4mA,
V+ −0.25
VID = 500mV
IL = 0.4mA,
VID = 500mV
IL = −4mA,
min
V
min
mV
max
mV
max
Output Swing Low
350
(LMV7239/LMV7235)
VID = −500mV
IL = −0.4mA,
VID = −500mV
450
10
www.national.com
4
5V Electrical Characteristics (Continued)
Unless otherwise specified, all limits guaranteed for TJ = 25˚C, VCM = V+/2, V+ = 5V, V− = 0V. Boldface limits apply at the
temperature extremes.
Symbol
ISC
Parameter
Conditions
Typ
(Note 5)
55
Limits
(Note 6)
25
Units
Output Short Circuit Current
Sourcing, VO = 0V
mA
min
(LMV7239 only)
(Note 3)
15
Sinking, VO = 5V
(LMV7235 RL = 10k)
(Note 3)
60
30
mA
min
20
IS
Supply Current
No load
65
62
57
45
5
95
µA
max
ns
110
tPD
Propagation Delay
Overdrive = 20mV
(Note 10)
max
ns
Overdrive = 50mV
(Note 10)
max
ns
Overdrive = 100mV
(Note 10)
max
ns
tSKEW
tr
Propagation Delay Skew
(LMV7239 only)
(Note 8)
Output Rise Time
LMV7239
1.2
100
ns
ns
10% to 90%
LMV7235
10% to 90%
(Note 10)
tf
Output Fall Time
90% to 10%
1.2
3
ns
ILEAKAGE
Output Leakeage Current
(LMV7235 only)
nA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical characteristics.
Note 2: Human body model, 1.5kΩ in series with 100pF. Machine model, 200pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
±
maximum allowed junction temperature of 150˚C. Output currents in excess of 30mA over long term may adversely affect reliability.
Note 4: The maximum power dissipation is a function of T , θ , and T . The maximum allowable power dissipation at any ambient temperature is
J(max)
JA
A
P
D
= (T
- T )/θ . All numbers apply for packages soldered directly into a PC board.
J(max) A JA
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: CMRR is not linear over the common mode range. Limits are guaranteed over the worst case from 0 to V
or V
to V
.
CC
CC/2
CC/2
Note 8: Propagation Delay Skew is defined as the absolute value of the difference between t
and t
.
PDHL
PDLH
Note 9: Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings.
Note 10: A 10k pull-up resistor was used when measuring the LMV7235. The rise time of the LMV7235 is a function of the R-C time constant.
5
www.national.com
Typical Performance Characteristics (Unless otherwise specified, VS = 5V, CL = 10pF, TA = 25˚C).
Supply Current vs. Supply Voltage
Sourcing Current vs. Output Voltage
10135904
10135905
Sourcing Current vs. Output Voltage
Sinking Current vs. Output Voltage
10135906
10135907
Sinking Current vs. Output Voltage
Input Bias Current vs. Input Voltage
10135909
10135908
www.national.com
6
Typical Performance Characteristics (Unless otherwise specified, VS = 5V, CL = 10pF, TA
=
25˚C). (Continued)
Input Bias Current vs. Input Voltage
Propagation Delay vs. Temperature
10135911
10135910
Propagation Delay vs. Capacitive Load
Propagation Delay vs. Capacitive Load
10135912
10135913
Propagation Delay vs. Input Overdrive
Propagation Delay vs. Input Overdrive
10135914
10135915
7
www.national.com
Typical Performance Characteristics (Unless otherwise specified, VS = 5V, CL = 10pF, TA
=
25˚C). (Continued)
Propagation Delay vs. Common Mode Voltage
Propagation Delay vs. Common Mode Voltage
10135916
10135917
Application Section
The LMV7235/LMV7239 are single supply comparators with
45ns of propagation delay and only 65µA of supply current.
Comparator with Hysteresis
The basic comparator configuration may oscillate or produce
a noisy output if the applied differential input voltage is near
the comparator’s offset voltage. This usually happens when
the input signal is moving very slowly across the compara-
tor’s switching threshold. This problem can be prevented by
the addition of hysteresis or positive feedback.
The LMV7235/LMV7239 are rail-to-rail input and output. The
typical input common mode voltage range of −0.2V below
the ground to 0.2V above the supply. The LMV7235/39 use a
complimentary PNP and NPN input stage in which the PNP
stage senses common mode voltage near V− and the NPN
stage senses common mode voltage near V+. If either of the
input signals falls below the negative common mode limit,
the parasitic PN junction formed by the substrate and the
base of the PNP will turn on resulting in an increase of input
bias current.
Inverting Comparator with Hysteresis
The inverting comparator with hysteresis requires a three
resistor network that is referenced to the supply voltage VCC
of the comparator. When VIN at the inverting input is less
than VA, the voltage at the non-inverting node of the com-
If one of the input goes above the positive common mode
limit, the output will still maintain the correct logic level as
long as the other input stays within the common mode range.
However, the propagation delay will increase. When both
inputs are outside the common mode voltage range, current
saturation occurs in the input stage, and the output becomes
unpredictable.
<
parator (VIN VA), the output voltage is high (for simplicity
assume VO switches as high as VCC). The three network
resistors can be represented as R1//R3 in series with R2.
The lower input trip voltage VA1 is defined as
VA1 = VCCR2 / ((R1//R3) + R2)
>
When VIN is greater than VA (VIN VA), the output voltage is
low, very close to ground. In this case the three network
resistors can be presented as R2//R3 in series with R1. The
upper trip voltage VA2 is defined as
The propagation delay does not increase significantly with
large differential input voltages. However, large differential
voltages greater than the supply voltage should be avoided
to prevent damage to the input stage.
VA2 = VCC (R2//R3) / ((R1+ (R2//R3)
The total hysteresis provided by the network is defined as
Delta VA = VA1- VA2
The LMV7239 has a push-pull output. When the output
switches, there is a direct path between VCC and ground,
causing high output sinking or sourcing current during the
transition. After the transition, the output current decreases
and the supply current settles back to about 65µA at 5V, thus
conserving power consumption.
To assure that the comparator will always switch fully to VCC
and not be pulled down by the load the resistors, values
should be chosen as follow:
<<
RPULL-UP
RLOAD
The LMV7235 has an open drain that requires a pull-up
resistor to a positive supply voltage for the output to switch
properly. When the internal output transistor is off, the output
voltage will be pulled up to the external positive voltage.
www.national.com
8
Application Section (Continued)
10135924
10135919
FIGURE 1.
10135920
Non-Inverting Comparator with Hysteresis
FIGURE 2. Non-Inverting Comparator with Hysteresis
Circuit Layout and Bypassing
A non inverting comparator with hysteresis requires a two
resistor network, and a voltage reference (VREF) at the in-
verting input. When VIN is low, the output is also low. For the
output to switch from low to high, VIN must rise up to VIN1
where VIN1 is calculated by.
The LMV7235/39 require high speed layout. Follow these
layout guidelines:
1. Use printed circuit board with a good, unbroken low-
inductance ground plane.
VIN1 = R1*(VREF/R2) + VREF
When VIN is high, the output is also high, to make the
comparator switch back to it’s low state, VIN must equal VREF
before VA will again equal VREF. VIN can be calculated by
2. Place a decoupling capacitor (0.1µF ceramic surface
mount capacitor) as close as possible to VCC pin.
3. On the inputs and the output, keep lead lengths as short
as possible to avoid unwanted parasitic feedback around the
comparator. Keep inputs away from output.
VIN2 = (VREF (R1+ R2) - VCCR1)/R2
The hysteresis of this circuit is the difference between VIN1
and VIN2
.
4. Solder the device directly to the printed circuit board rather
than using a socket.
Delta VIN = VCCR1/R2
5. For slow moving input signals, take care to prevent para-
sitic feedback. A small capacitor (1000pF or less) placed
between the inputs can help eliminate oscillations in the
transition region. This capacitor causes some degradation to
tPD when the source impedance is low.
6. The topside ground plane runs between the output and
inputs.
7. Ground trace from the ground pin runs under the device
up to the bypass capacitor, shielding the inputs from the
outputs.
9
www.national.com
the inverting input node at an appropriate DC average level
based on the output. The crystal’s path provides resonant
positive feedback and stable oscillation occurs. The output
duty cycle for this circuit is roughly 50%, but it is affected by
resistor tolerances and to a lesser extent by the comparator
offset.
Application Section (Continued)
Zero-Crossing Detector
The inverting input is connected to ground and the non-
inverting input is connected to 100mVp-p signal. As the
signal at the non-inverting input crosses 0V, the compara-
tor’s output changes state.
10135918
10135922
FIGURE 3. Zero-Crossing Detector
Threshold Detector
FIGURE 5. Crystal Oscillator
IR Receiver
Instead of tying the inverting input to 0V, the inverting input
can be tied to a reference voltage. The non-inverting input is
connected to the input. As the input passes the VREF thresh-
old, the comparator’s output changes state.
The LMV7239 is an ideal candidate to be used as an infrared
receiver. The infrared photo diode creates a current relative
to the amount of infrared light present. The current creates a
voltage across RD. When this voltage level cross the voltage
applied by the voltage divider to the inverting input, the
output transitions.
10135921
FIGURE 4. Threshold Detector
Crystal Oscillator
A simple crystal oscillator using the LMV7239 is shown
below. Resistors R1 and R2 set the bias point at the com-
parator’s non-inverting input. Resistors R3, R4 and C1 sets
10135923
FIGURE 6. IR Receiver
www.national.com
10
Physical Dimensions inches (millimeters) unless otherwise noted
5-Pin SC70-5
NS Package Number MAA05A
11
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
5-Pin SOT23-5
NS Package Number MF05A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: support@nsc.com
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
LMV7235M5X
45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
NSC
LMV7235M5X
LMV7235/LMV7239/LMV7239Q 75 nsec, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
TI
LMV7235M7
45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
NSC
LMV7235M7
LMV7235/LMV7239/LMV7239Q 75 nsec, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
TI
LMV7235M7X
45ns, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
NSC
LMV7235M7X
LMV7235/LMV7239/LMV7239Q 75 nsec, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
TI
LMV7235_06
45 nsec, Ultra Low Power, Low Voltage, Rail-to-Rail Input Comparator with Open-Drain/Push-Pull Output
NSC
©2020 ICPDF网 联系我们和版权申明