LP3882EMR-1.5 [NSC]
IC VREG 1.5 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator;
| 型号： | LP3882EMR-1.5 |
| 厂家： | 
National Semiconductor |
| 描述： | IC VREG 1.5 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator 光电二极管 |
| 文件： | 总13页 (文件大小：788K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
June 2006
LP3882
1.5A Fast-Response Ultra Low Dropout Linear
Regulators
General Description
Features
@
n Ultra low dropout voltage (110 mV 1.5A typ)
The LP3882 is a high current, fast response regulator which
can maintain output voltage regulation with minimum input to
output voltage drop. Fabricated on a CMOS process, the
device operates from two input voltages: Vbias provides
voltage to drive the gate of the N-MOS power transistor,
while Vin is the input voltage which supplies power to the
load. The use of an external bias rail allows the part to
operate from ultra low Vin voltages. Unlike bipolar regula-
tors, the CMOS architecture consumes extremely low quies-
cent current at any output load current. The use of an
n Low ground pin current
n Load regulation of 0.04%/A
n 60 nA typical quiescent current in shutdown
n 1.5% output accuracy (25˚C)
n TO-220, TO-263 and PSOP-8 packages
n Over temperature/over current protection
n −40˚C to +125˚C junction temperature range
N-MOS power transistor results in wide bandwidth, yet mini- Applications
mum external capacitance is required to maintain loop sta-
bility.
n DSP Power Supplies
n Server Core and I/O Supplies
n PC Add-in-Cards
n Local Regulators in Set-Top Boxes
n Microcontroller Power Supplies
n High Efficiency Power Supplies
n SMPS Post-Regulators
The fast transient response of these devices makes them
suitable for use in powering DSP, Microcontroller Core volt-
ages and Switch Mode Power Supply post regulators. The
parts are available in TO-220, TO-263 and PSOP-8 pack-
ages.
@
Dropout Voltage: 110 mV (typ) 1.5A load current.
Ground Pin Current: 3 mA (typ) at full load.
Shutdown Current: 60 nA (typ) when S/D pin is low.
Precision Output Voltage: 1.5% room temperature accu-
racy.
Typical Application Circuit
20063201
At least 4.7 µF of input and output capacitance is required for stability.
© 2006 National Semiconductor Corporation
DS200632
www.national.com
Connection Diagrams
20063202
20063203
TO-220, Top View
TO-263, Top View
20063253
PSOP-8, Top View
Ordering Information
Order Number
LP3882ES-1.2
LP3882ESX-1.2
LP3882ET-1.2
Package Type
TO263-5
TO263-5
TO220-5
TO263-5
TO263-5
TO220-5
TO263-5
TO263-5
TO220-5
PSOP-8
PSOP-8
PSOP-8
PSOP-8
PSOP-8
PSOP-8
Package Drawing
TS5B
Supplied As
Rail
TS5B
Tape and Reel
T05D
Rail
LP3882ES-1.5
LP3882ESX-1.5
LP3882ET-1.5
TS5B
Rail
TS5B
Tape and Reel
T05D
Rail
LP3882ES-1.8
LP3882ESX-1.8
LP3882ET-1.8
TS5B
Rail
TS5B
Tape and Reel
T05D
Rail
LP3882EMR-1.2
LP3882EMRX-1.2
LP3882EMR-1.5
LP3882EMRX-1.5
LP3882EMR-1.8
LP3882EMRX-1.8
MRA08B
MRA08B
MRA08B
MRA08B
MRA08B
MRA08B
Rail
2500 Units on Tape and Reel
Rail
2500 Units on Tape and Reel
Rail
2500 Units on Tape and Reel
Block Diagram
20063224
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
IOUT (Survival)
Internally Limited
−0.3V to +6V
Output Voltage (Survival)
Junction Temperature
−40˚C to +150˚C
Storage Temperature Range
Lead Temp. (Soldering, 5 seconds)
ESD Rating
−65˚C to +150˚C
260˚C
Operating Ratings
VIN Supply Voltage
Shutdown Input Voltage
IOUT
(VOUT + VDO) to 5.5V
0 to +6V
Human Body Model (Note 3)
Machine Model (Note 10)
Power Dissipation (Note 2)
VIN Supply Voltage (Survival)
VBIAS Supply Voltage (Survival)
Shutdown Input Voltage (Survival)
2 kV
200V
1.5A
Operating Junction
Temperature Range
VBIAS Supply Voltage
−40˚C to +125˚C
Internally Limited
−0.3V to +6V
−0.3V to +7V
−0.3V to +7V
4.5V to 6V
Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply
over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, VBIAS = 4.5V, IL = 10 mA, CIN
COUT = 4.7 µF, VS/D = VBIAS
=
.
MIN
(Note 5)
1.198
Typical
(Note 4)
MAX
(Note 5)
1.234
Symbol
VO
Parameter
Conditions
Units
<
<
Output Voltage Tolerance
10 mA IL 1.5A
VO(NOM) + 1V ≤ VIN ≤ 5.5V
4.5V ≤ VBIAS ≤ 6V
1.216
1.5
1.186
1.246
1.478
1.522
V
1.455
1.545
1.773
1.827
1.8
1.746
1.854
∆VO/∆VIN
∆VO/∆IL
VDO
Output Voltage Line Regulation
(Note 7)
VO(NOM) + 1V ≤ VIN ≤ 5.5V
0.01
%/V
%/A
<
<
Output Voltage Load Regulation 10 mA IL 1.5A
0.04
(Note 8)
0.06
Dropout Voltage (Note 9)
IL = 1.5A
170
270
190
320
7
110
125
3
(TO220 and TO263 only)
IL = 1.5A
mV
(PSOP only)
<
<
IQ(VIN
)
Quiescent Current Drawn from
VIN Supply
10 mA IL 1.5A
mA
µA
8
V
≤ 0.3V
1
S/D
0.03
1
30
2
<
<
IQ(VBIAS
)
Quiescent Current Drawn from
VBIAS Supply
10 mA IL 1.5A
mA
3
V
≤ 0.3V
1
S/D
0.03
4.3
µA
A
30
ISC
Short-Circuit Current
VOUT = 0V
Shutdown Input
VSDT
Output Turn-off Threshold
Output = ON
Output = OFF
RLOAD X COUT
RLOAD X COUT
V S/D =1.3V
1.3
0.7
0.7
20
15
1
V
0.3
<<
<<
Td (OFF)
Td (ON)
IS/D
Turn-OFF Delay
Turn-ON Delay
S/D Input Current
Td (OFF)
Td (ON)
µs
µA
V
≤ 0.3V
−1
S/D
3
www.national.com
Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply
over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, VBIAS = 4.5V, IL = 10 mA, CIN
COUT = 4.7 µF, VS/D = VBIAS. (Continued)
=
MIN
(Note 5)
Typical
(Note 4)
MAX
(Note 5)
Symbol
Parameter
Conditions
Units
AC Parameters
PSRR (VIN
)
Ripple Rejection for VIN Input
Voltage
VIN = VOUT +1V, f = 120 Hz
80
65
70
VIN = VOUT + 1V, f = 1 kHz
dB
PSRR
Ripple Rejection for VBIAS
Voltage
VBIAS = VOUT + 3V, f = 120 Hz
(VBIAS
)
VBIAS = VOUT + 3V, f = 1 kHz
f = 120 Hz
65
1
Output Noise Density
Output Noise Voltage
VOUT = 1.8V
µV/root−Hz
µV (rms)
en
BW = 10 Hz − 100 kHz
BW = 300 Hz − 300 kHz
150
90
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink thermal values. θ
for TO-220
J-A
devices is 65˚C/W if no heatsink is used. If the TO-220 device is attached to a heatsink, a θ
approximately 40˚C/W if soldered down to a copper plane which is at least 1.5 square inches in area. θ
value of 4˚C/W can be assumed. θ
for TO-263 devices is
J-S
J-A
value for typical PSOP-8 PC board mounting is 166˚C/W.
J-A
If power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25˚C operation.
Note 5: Limits are guaranteed through testing, statistical correlation, or design.
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 7: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 8: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load to full load.
Note 9: Dropout voltage is defined as the minimum input to output differential required to maintain the output with 2% of nominal value. The PSOP-8 package
devices have a slightly higher dropout voltage due to increased band wire resistance.
Note 10: The machine model is a 220 pF capacitor discharged directly into each pin. The machine model ESD rating of pin 5 is 100V.
www.national.com
4
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7µF, Cin =
4.7µF, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V.
Dropout vs IL
IGND vs VSD
20063205
20063204
VOUT vs Temperature
DC Load Regulation
20063206
20063207
Line Regulation vs VIN
Line Regulation vs VBIAS
20063208
20063209
5
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7µF, Cin =
4.7µF, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V. (Continued)
IBIAS vs IL
IGND vs VSD
20063212
20063210
Noise Measurement
VOUTStartup Waveform
20063215
20063214
VOUTStartup Waveform
Line Regulation vs VBIAS
20063218
20063216
www.national.com
6
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7µF, Cin =
4.7µF, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V. (Continued)
Line Regulation vs VBIAS
VIN PSRR
20063219
20063220
VIN PSRR
VBIAS PSRR
20063223
20063222
7
www.national.com
The reason for this is that PNP or P-FET regulators have a
higher output impedance (compared to an NPN regulator),
which results in a pole-zero pair being formed by every
different capacitor connected to the output.
Application Hints
EXTERNAL CAPACITORS
To assure regulator stability, input and output capacitors are
required as shown in the Typical Application Circuit.
The zero frequency is approximately:
Fz = 1 / (2 X π X ESR X C)
OUTPUT CAPACITOR
Where ESR is the equivalent series resistance of the capaci-
tor, and C is the value of capacitance.
At least 4.7µF of output capacitance is required for stability
(the amount of capacitance can be increased without limit).
The output capacitor must be located less than 1 cm from
the output pin of the IC and returned to a clean analog
ground. The ESR (equivalent series resistance) of the output
capacitor must be within the "stable" range as shown in the
graph below over the full operating temperature range for
stable operation.
The pole frequency is:
Fp = 1 / (2 X π X RL X C)
Where RL is the load resistance connected to the regulator
output.
To understand why a small capacitor can reduce phase
margin: assume a typical LDO with a bandwidth of 1MHz,
which is delivering 0.5A of current from a 2.5V output (which
means RL is 5 Ohms). We then place a .047 µF capacitor on
the output. This creates a pole whose frequency is:
Fp = 1 / (2 X π X 5 X .047 X 10E-6) = 677 kHz
This pole would add close to 60 degrees of phase lag at the
crossover (unity gain) frequency of 1 MHz, which would
almost certainly make this regulator oscillate. Depending on
the load current, output voltage, and bandwidth, there are
usually values of small capacitors which can seriously re-
duce phase margin. If the capacitors are ceramic, they tend
to oscillate more easily because they have very little internal
inductance to damp it out. If bypass capacitors are used, it is
best to place them near the load and use trace inductance to
"decouple" them from the regulator output.
INPUT CAPACITOR
The input capacitor must be at least 4.7 µF, but can be
increased without limit. It’s purpose is to provide a low
source impedance for the regulator input. Ceramic capaci-
tors work best for this, but Tantalums are also very good.
There is no ESR limitation on the input capacitor (the lower,
the better). Aluminum electrolytics can be used, but their
ESR increase very quickly at cold temperatures. They are
not recommended for any application where temperatures
go below about 10˚C.
20063231
Minimum ESR vs Output Load Current
Tantalum capacitors are recommended for the output as
their ESR is ideally suited to the part’s requirements and the
ESR is very stable over temperature. Aluminum electrolytics
are not recommended because their ESR increases very
rapidly at temperatures below 10C. Aluminum caps can only
be used in applications where lower temperature operation
is not required.
BIAS CAPACITOR
A second problem with Al caps is that many have ESR’s
which are only specified at low frequencies. The typical loop
bandwidth of a linear regulator is a few hundred kHz to
several MHz. If an Al cap is used for the output cap, it must
be one whose ESR is specified at a frequency of 100 kHz or
more.
The 0.1µF capacitor on the bias line can be any good quality
capacitor (ceramic is recommended).
BIAS VOLTAGE
The bias voltage is an external voltage rail required to get
gate drive for the N-FET pass transistor. Bias voltage must
be in the range of 4.5 - 6V to assure proper operation of the
part.
Because the ESR of ceramic capacitors is only a few milli
Ohms, they are not suitable for use as output capacitors on
LP388X devices. The regulator output can tolerate ceramic
capacitance totaling up to 15% of the amount of Tantalum
capacitance connected from the output to ground.
UNDER VOLTAGE LOCKOUT
The bias voltage is monitored by a circuit which prevents the
regulator output from turning on if the bias voltage is below
approximately 4V.
OUTPUT "BYPASS" CAPACITORS
Many designers place small value "bypass" capacitors at
various circuit points to reduce noise. Ceramic capacitors in
the value range of about 1000pF to 0.1µF placed directly on
the output of a PNP or P-FET LDO regulator can cause a
loss of phase margin which can result in oscillations, even
when a Tantalum output capacitor is in parallel with it. This is
not unique to National Semiconductor LDO regulators, it is
true of any P-type LDO regulator.
SHUTDOWN OPERATION
Pulling down the shutdown (S/D) pin will turn-off the regula-
tor. Pin S/D must be actively terminated through a pull-up
resistor (10 kΩ to 100 kΩ) for a proper operation. If this pin
is driven from a source that actively pulls high and low (such
as a CMOS rail to rail comparator), the pull-up resistor is not
required. This pin must be tied to Vin if not used.
www.national.com
8
In this equation, θCH is the thermal resistance from the case
to the surface of the heat sink and θJC is the thermal resis-
tance from the junction to the surface of the case. θJC is
about 3˚C/W for a TO220 package. The value for θCH de-
pends on method of attachment, insulator, etc. θCH varies
between 1.5˚C/W to 2.5˚C/W. If the exact value is unknown,
2˚C/W can be assumed.
Application Hints (Continued)
POWER DISSIPATION/HEATSINKING
A heatsink may be required depending on the maximum
power dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction tem-
perature must be within the range specified under operating
conditions. The total power dissipation of the device is given
by:
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as
a heatsink. The tab of these packages are soldered to the
copper plane for heat sinking. The graph below shows a
curve for the θJA of TO-263 package for different copper area
sizes, using a typical PCB with 1 ounce copper and no solder
mask over the copper area for heat sinking.
PD = (VIN−VOUT)IOUT+ (VIN)IGND
where IGND is the operating ground current of the device.
The maximum allowable temperature rise (TRmax) depends
on the maximum ambient temperature (TAmax) of the appli-
cation, and the maximum allowable junction temperature
(TJmax):
TRmax = TJmax− TAmax
The maximum allowable value for junction to ambient Ther-
mal Resistance, θJA, can be calculated using the formula:
θJA = TRmax / PD
These parts are available in TO-220 and TO-263 packages.
The thermal resistance depends on amount of copper area
or heat sink, and on air flow. If the maximum allowable value
of θJA calculated above is ≥ 60 ˚C/W for TO-220 package
and ≥ 60 ˚C/W for TO-263 package no heatsink is needed
since the package can dissipate enough heat to satisfy these
requirements. If the value for allowable θJA falls below these
limits, a heat sink is required.
HEATSINKING TO-220 PACKAGE
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of θJA will
be same as shown in next section for TO263 package.
20063225
FIGURE 1. θJA vs Copper (1 Ounce) Area for TO-263
package
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θHA≤ θJA − θCH − θJC
.
9
www.national.com
slug must be soldered down to a copper plane to get good
heat transfer. It can also be connected through vias to inter-
nal copper planes. Since the heat slug is at ground potential,
traces must not be routed under it which are not at ground
potential. Under all possible conditions, the junction tem-
perature must be within the range specified under operating
conditions.
Application Hints (Continued)
As shown in the graph below, increasing the copper area
beyond 1 square inch produces very little improvement. The
minimum value for θJA for the TO-263 package mounted to a
PCB is 32˚C/W.
Figure 2 shows the maximum allowable power dissipation
for TO-263 packages for different ambient temperatures,
assuming θJA is 35˚C/W and the maximum junction tempera-
ture is 125˚C.
Figure 3 shows a curve for the θJA of the PSOP package for
different copper area sizes using a typical PCB with one
ounce copper in still air.
20063226
20063254
FIGURE 2. Maximum Power Dissipation vs Ambient
Temperature For TO-263 Package
FIGURE 3. θJA vs. Copper (1 ounce) Area for PSOP
Package
HEATSINKING PSOP PACKAGE
Heatsinking for the PSOP-8 package is accomplished by
allowing heat to flow through the ground slug on the bottom
of the package into the copper on the PC board. The heat
www.national.com
10
Physical Dimensions inches (millimeters) unless otherwise noted
TO220 5-lead, Molded, Stagger Bend Package (TO220-5)
NS Package Number T05D
TO263 5-Lead, Molded, Surface Mount Package (TO263-5)
NS Package Number TS5B
11
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
PSOP 8-Lead, Molded, PSOP-2
NS Package Number MRA08B
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances
and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at:
www.national.com/quality/green.
Lead free products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号：
LP3882EMR-1.5/NOPB
IC VREG 1.5 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
LP3882EMR-1.8
IC VREG 1.8 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
LP3882EMR-1.8/NOPB
IC VREG 1.8 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
LP3882EMRX-1.2/NOPB
IC VREG 1.216 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
LP3882EMRX-1.8
IC VREG 1.8 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
LP3882EMRX-1.8/NOPB
IC VREG 1.8 V FIXED POSITIVE LDO REGULATOR, 0.32 V DROPOUT, PDSO8, PSOP-8, Fixed Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明