PC8477B_技术文档

August 1993

PC8477B (SuperFDC^TM)

Advanced Floppy Disk Controller

Y

16 byte FIFO (default disabled)

Ð Burst and Non-Burst modes

Ð Programmable threshold

General Description

The PC8477B CMOS advanced floppy disk controller is an

enhanced version of National’s DP8473 floppy controller.

The PC8477B is software compatible with the DP8473 and

NEC mPD765 floppy disk controllers. In addition, it is pin and

software compatible with the Intel 82077AA floppy control-

ler. The PC8477B, a 24 MHz crystal, a device chip select,

and a resistor package are all that is needed for a complete

PC-AT , PS/2 or EISA floppy controller solution.

Y

Perpendicular Mode Recording drive support

High performance internal analog data separator (no

external filter components required)

Low power CMOS with manual power down mode

Automatic power down mode, for complete software

transparency

Y

É

Y

Integrates all PC-AT, and PS/2 logic

Ð On chip Oscillator

Ð PC compatible FDC address decode

Ð PS/2 Model 30 and Model 50/60/80 diagnostic

registers

The PC8477B includes advanced features such as

a

16 byte FIFO (Burst and Non-Burst modes), support of Per-

pendicular Recording Mode disk drives, PS/2 diagnostic

registers for Model 30 and Models 50/60/80, standard

CMOS disk I/O, and additional commands to control these

new features. The 16 byte FIFO will increase system per-

formance at higher data rates and with multi-tasking bus

structures. This controller is designed to fit into all PC-AT,

EISA, and PS/2 designs, as well as other advanced applica-

tions.

Ð DMA control circuitry

Ð High current CMOS disk interface outputs

Ð Data Rate and Digital Output registers

Ð 12 mA mP bus interface buffers

Data Rate Support: 250/300 kb/s, 500 kb/s,

and 1 Mb/s

Y

Write precompensation software programmable

68 pin PLCC package

Features

Y

Pin and software compatible with Intel 82077AA FDC

60 pin PQFP package

Ideal for space limited applications

Y

Software compatible with NSC’s DP8473

Functional Block Diagram

TL/F/11332–3

FIGURE 1-1

SuperFDC^TMis a trademark of National Semiconductor Corporation.

TRI-STATEÉ is a registered trademark of National Semiconductor Corporation.

IBMÉ, PC-ATÉ and PS/2É are registered trademarks of International Business Machines Corp.

C

1995 National Semiconductor Corporation

TL/F/11332

RRD-B30M75/Printed in U. S. A.

Table of Contents

1.0 INTRODUCTION

4.2.15 Scan Commands

2.0 PIN DESCRIPTION

4.2.16 Seek Command

4.2.17 Sense Drive Status Command

4.2.18 Sense Interrupt Command

4.2.19 Set Track Command

4.2.20 Specify Command

3.0 REGISTER DESCRIPTION

3.1 Status Register A (SRA)

3.1.1 SRAÐPS/2 Mode

3.1.2 SRAÐModel 30 Mode

3.2 Status Register B (SRB)

3.2.1 SRBÐPS/2 Mode

4.2.21 Verify Command

4.2.22 Version Command

3.2.2 SRBÐModel 30 Mode

3.3 Digital Output Register (DOR)

3.4 Tape Drive Register (TDR)

3.5 Main Status Register (MSR)

3.6 Data Rate Select Register (DSR)

3.7 Data Register (FIFO)

4.2.23 Write Data Command

4.2.24 Write Deleted Data Command

5.0 FUNCTIONAL DESCRIPTION

5.1 Microprocessor Interface

5.2 Modes of Operation

5.3 Controller Phases

3.8 Digital Input Register (DIR)

3.8.1 DIRÐPC-AT Mode

5.3.1 Command Phase

5.3.2 Execution Phase

3.8.2 DIRÐPS/2 Mode

5.3.2.1 DMA ModeÐFIFO Disabled

5.3.2.2 DMA ModeÐFIFO Enabled

5.3.2.3 Interrupt ModeÐFIFO Disabled

5.3.2.4 Interrupt ModeÐFIFO Enabled

5.3.2.5 Software Polling

3.8.3 DIRÐModel 30 Mode

3.9 Configuration Control Register (CCR)

3.9.1 CCRÐPC-AT and PS/2 Modes

3.9.2 CCRÐModel 30 Mode

3.10 Result Phase Status Registers

3.10.1 Status Register 0 (ST0)

3.10.2 Status Register 1 (ST1)

3.10.3 Status Register 2 (ST2)

3.10.4 Status Register 3 (ST3)

4.0 COMMAND SET DESCRIPTION

4.1 Command Set Summary

4.2 Command Description

5.3.3 Result Phase

5.3.4 Idle Phase

5.3.5 Drive Polling Phase

5.4 Data Separator

5.5 Crystal Oscillator

5.6 Dynamic Window Margin Performance

5.7 Perpendicular Recording Mode

5.8 Data Rate Selection

4.2.1 Configure Command

4.2.2 Dumpreg Command

5.9 Write Precompensation

5.10 Low Power Mode Logic

5.11 Reset Operation

4.2.3 Format Command

4.2.4 Invalid Command

6.0 DEVICE DESCRIPTION

6.1 DC Electrical Characteristics

6.2 AC Electrical Characteristics

6.2.1 AC Test Conditions

4.2.5 Lock Command

4.2.6 Mode Command

4.2.7 NSC Command

4.2.8 Perpendicular Mode Command

4.2.9 Read Data Command

4.2.10 Read Deleted Data Command

4.2.11 Read ID Command

6.2.2 Clock Timing

6.2.3 Microprocessor Read Timing

6.2.4 Microprocessor Write Timing

6.2.5 DMA Timing

4.2.12 Read A Track Command

4.2.13 Recalibrate Command

4.2.14 Relative Seek Command

6.2.6 Reset Timing

6.2.7 Write Data Timing

6.2.8 Drive Control Timing

6.2.9 Read Data Timing

7.0 REFERENCE SECTION

7.1 Mnemonic Definitions for PC8477B Commands

7.2 PC8477B Enhancements vs. 82077AA

7.3 PC8477B Interface in a PC-AT

7.4 Software Initialization Sequence

7.5 PC8477B/PC8477A differences

7.6 Revision History

2

List of Figures

PC8477B Functional Block Diagram ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ1-1

PC8477B Pin Diagram for 68 Pin PLCC and 60 Pin PQFP ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ1-2

IBM , Perpendicular, and ISO Formats Supported by Format CommandÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-1

É

PC8477B Data Separator Block Diagram ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ5-1

Read Data AlgorithmÐState DiagramÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ5-2

PC8477B Dynamic Window Margin Performance ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ5-3

g

PC8477B Dynamic Window Margin Performance with 3% ISVÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ5-4

Perpendicular Recording Drive R/W Head and Pre-Erase Head ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ5-5

Clock Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-1

Microprocessor Read Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-2

Microprocessor Write Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-3

DMA Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-4

Reset Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-5

Write Data Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-6

Drive Control TimingÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-7

Read Data Timing ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-8

PC8477B in a PC-AT System ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ7-1

PC84777B Initialization ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ7-2

List of Tables

Register Description and Addresses ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-1

Drive Enable Values ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-2

Tape Drive Assignment ValuesÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-3

Write Precompensation Delays ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-4

Default Precompensation DelaysÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-5

Data Rate Select EncodingÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ3-6

Typical Format Gap Length Values ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-1

DENSEL Encoding ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-2

DENSEL Default Encoding ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-3

Effects of WGATE and GAP ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-4

Sector Size SelectionÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-5

SK Effect of Read Data Command ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-6

Result Phase Termination Values with No Error ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-7

SK Effect on Read Deleted Data Command ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-8

Maximum Recalibrate Step Pulses Based on R255 and ETR ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-9

Scan Command Termination ValuesÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-10

Status Register 0 Termination Codes ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-11

Set Track Register Address ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-12

Step Rate (SRT) Values ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-13

Motor Off Time (MFT) Values ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-14

Motor On Time (MNT) ValuesÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-15

Verify Command Result Phase Table ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ4-16

Nominal t , t

Values ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-1

ValuesÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ6-2

ICP DRP

Minimum t

WDW

PC8477B–82077 Parameter Comparison ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ7-1

Density Encoding ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ7-2

3

1.0 Introduction

The PC8477B advanced floppy disk controller is suitable for

all PC-AT, EISA, PS/2, and general purpose applications.

The operational mode (PC-AT, PS/2, and Model 30) of the

PC8477B is determined by hardware strapping of the IDENT

and MFM pins. DP8473 and Intel 82077AA software com-

patibility is provided. Key features include the 16 byte FIFO,

PS/2 diagnostic register support, the perpendicular record-

ing mode, CMOS disk interface, and a high performance

analog data separator.

The high performance internal analog data separator needs

no external components. It improves on the window margin

performance standards of the DP8473, and is compatible

with the strict data separator requirements of floppy and

floppy-tape drives.

The PC8477B contains write precompensation and circuitry

that will default to 125 ns for 250, 300, and 500 kb/s,

41.67 ns at 1 Mb/s. These values can be overridden

through software to disable write precompensation or to

provide levels of precompensation up to 250 ns. The

PC8477B has internal 12 mA data bus buffers which allow

direct connection to the system bus. The internal 48 mA

totem-pole disk interface buffers are compatible with both

CMOS drive inputs and 150X resistor terminated disk drive

inputs.

The PC8477B supports the standard PC data rates of 250,

300, 500 kb/s, and 1 Mb/s in MFM encoded data mode, but

is no longer guaranteed through functional testing to sup-

port the older FM encoded data mode. References to the

older FM mode remain in this document to clarify the true

functional operation of the device.

The 1 Mb/s data rate is used by new high performance tape

and floppy drives emerging in the PC market today. The new

floppy drives utilize high density media which requires the

PC8477B supported perpendicular recording mode format.

When used with the 1 Mb/s data rate this new format allows

the use of 4 Mb floppy drives which format ED media to

2.88 MB data capacity.

The PC8477B is available in a 68 pin Plastic Leaded Chip

Carrier (PLCC) package, and in a 60 pin Plastic Quad Flat

Package (PQFP).

4

Connection Diagrams

TL/F/11332–1

Plastic Chip Carrier (V)

Order Number PC8477BV-1

See NS Package Number V68A

TL/F/11332–2

Plastic Quad Flat Package (VF)

Order Number PC8477BVF-1

See NS Package Number VF60A

FIGURE 1-2

5

2.0 Pin Description

PLCC

PQFP

Symbol

I/O

Function

A0

7

8

44

45

46

I

Address. These address lines from the microprocessor determine which internal FDC

register is accessed. See TABLE 3-1 in the Register Description section. A0–A2 are don’t

cares during a DMA transfer.

A1

A2

10

AVCC

CS

46

6

17

43

Analog Supply. This pin is the 5V supply for the analog data separator.

I

Chip Select. Active low input from address decoder used to enable the RD and WR inputs

during register I/O. Should be held inactive during DMA transfers.

D0

D1

D2

D3

D4

D5

D6

D7

11

13

14

15

17

19

20

22

47

48

49

50

52

54

55

56

I/O Data. Bi-directional data lines to the microprocessor. D0 is the LSB and D7 is the MSB.

These signals all have 12 mA buffered outputs.

DACK

3

40

I

DMA Acknowledge. Active low input to acknowledge the DMA request and enable the RD

and WR inputs during a DMA transfer. DACK should be held inactive high during normal read

or write accesses when CS is active. When in PC-AT or Model 30 mode, this signal is

enabled by bit D3 of the DOR. When in PS/2 mode, DAK is always enabled, and bit D3 of the

DOR is reserved.

DENSEL

DIR

49

56

19

26

O

Density Select. Indicates when a high density data rate (500 kb/s or 1 Mb/s) or a low

density data rate (250 or 300 kb/s) has been selected. DENSEL is active high for high

density (5.25 drives) when IDENT is high, and active low for high density (3.5 drives) when

×

IDENT is low. DENSEL is also programmable via the Mode command (see Section 4.2.6).

e

step out) during a seek operation. During read or writes, DIR will be inactive.

O

Direction. This output determines the direction of the head movement (active

e

step in,

inactive

DR0

DR1

DR2

DR3

58

62

64

67

28

32

34

36

Drive Select 0–3. These are the decoded drive select outputs that are controlled by Digital

Output Register bits D0, D1. The Drive Select outputs are gated by DOR bits 4–7.

DRATE0

DRATE1

28

29

2

3

O

Data Rate 0,1. These outputs reflect the currently selected data rate, (bits 0 and 1 in the

CCR or the DSR, whichever was written to last). These pins are totem-pole buffered outputs

(6 mA sink, 4 mA source).

DRQ

24

58

DMA Request. Active high output to signal the DMA controller that a data transfer is needed.

When in PC-AT or Model 30 mode, this signal is enabled by bit D3 of the DOR. When in PS/2

mode, DRQ is always enabled, and bit D3 of the DOR is reserved.

DRV2

30

31

4

5

I

Drive2. This input indicates whether a second disk drive has been installed. The state of this

pin is available from Status Register A in PS/2 mode.

DSKCHG

Disk Change. The input indicates if the drive door has been opened. The state of this pin is

available from the Digital Input register. This pin can also be configured as the RGATE data

separator diagnostic input via the Mode command (see Section 4.2.6).

GND

9, 12,

10, 11,

Ground

16, 21, 12, 14,

36, 50, 15, 20,

54, 59, 24, 29,

65

51

GNDA

45

16

Analog Ground. This is the analog ground for the data separator.

6

2.0 Pin Description (Continued)

PLCC PQFP

Symbol

I/O

Function

HDSEL

51

21

O

Head Select. This output determines which side of the disk drive is accessed. Active selects side

1, inactive selects side 0.

HIFIL

38

27

(Note 1)

1

High Filter. No connect. No external capacitor is required. An external capacitor can be

connected, but it will have no effect on the data separator performance.

IDENT

I

Identity. During chip reset, the IDENT and MFM pins are sampled to determine the mode of

operation according to the following table:

IDENT

MFM

Mode

1

0

1 or NC

PC-AT Mode

Illegal

0

1 or NC

0

PS/2 Mode

Model 30 Mode

AT ModeÐThe DMA enable bit in the DOR is valid. TC is active high. Status Registers A and B

are disabled (TRI-STATE ).

É

Model 30 ModeÐThe DMA enable bit in the DOR is valid. TC is active high. Status Registers A

and B are enabled.

PS/2 ModeÐThe DMA enable bit in the DOR is a don’t care, and the DRQ and INT signals will

always be enabled. TC is active low. Status Registers A and B are enabled.

After chip reset, the state of IDENT determines the polarity of the DENSEL output.

When IDENT is a logic ‘‘1’’, DENSEL is active high for 500 kb/s and 1 Mb/s data rates.

When IDENT is a logic ‘‘0’’, DENSEL is active low for 500 kb/s and 1 Mb/s data rates.

(See Mode command for further explanation of DENSEL.)

INDEX

INT

26

23

60

57

I

Index. This input signals the beginning of a track.

O

Interrupt. Active high output to signal the completion of the execution phase for certain

commands. Also used to signal when a data transfer is ready during a Non-DMA operation. When

in PC-AT or Model 30 mode, this signal is enabled by bit D3 of the DOR. When in PS/2 mode, INT

is always enabled, and bit D3 of the DOR is reserved.

INVERT

35

9

I

Invert. Determines the polarity of all disk interface signals. When tied low, the internal disk output

buffers and inverting Schmitt input receivers are enabled, and the disk interface signals are active

low. When tied high, the disk interface signals are active high, and external receivers and output

buffers are required.

LOFIL

MFM

37

48

(Note 1)

18

Low Filter. No connect. No external capacitor is required. An external capacitor can be

connected, but it will have no effect on the data separator performance.

I/O MFM. During a chip reset when in PS/2 mode (IDENT low), this pin is sampled to select the PS/2

mode (MFM high), or the Model 30 mode (MFM low). An internal pull-up or external pull-down

10 kX resistor will select between the two PS/2 modes. When the PC-AT mode is desired (IDENT

high), MFM should be left pulled high internally. MFM reflects the current data encoding format

e

low. Defaults to low after a chip reset. This signal

when RESET is inactive. MFM

high, FM

can also be configured as the PUMP data separator diagnostic output via the Mode command (see

Section 4.2.6).

MTR0

MTR1

MTR2

MTR3

57

61

63

66

27

31

33

35

O

Motor Select 0–3. These are the motor enable lines for drives 0–3, and are controlled by bits D7–

D4 of the Digital Output register.

NC

42

43

44

47

(Note 1)

No Connect. These pins must be left unconnected.

7

2.0 Pin Description (Continued)

PLCC

PQFP

Symbol

I/O

Function

PLL0

39

40

(Note 1)

Phase Locked Loop 0,1. No connects. These pins can be tied high or low with no affect

PLL1

on the data separator performance.

RD

4

41

13

6

I

Read. Active low input to signal a read from the controller to the microprocessor.

Read Data. This input is the raw serial data read from the disk drive.

RDATA

RESET

41

32

Reset. Active high input that resets the controller to the idle state, and resets all disk

interface outputs to their inactive states. The DOR, DSR, CCR, Mode command,

Configure command, and Lock command parameters are cleared to their default values.

The Specify command parameters are not affected.

STEP

TC

55

25

59

O

I

Step. This output signal issues pulses to the disk drive at a software programmable rate

to move the head during a seek operation.

Terminal Count. Control signal from the DMA controller to indicate the termination of a

DMA transfer. TC is accepted only when DACK is active. TC is active high in PC-AT and

Model 30 modes, and active low in PS/2 mode.

TRK0

2

39

I

Track 0. This input indicates to the controller that the head of the selected disk drive is at

track zero.

a

Voltage. This is the 5V supply voltage for the digital circuitry.

V

CC

18

60

68

30

37

53

WDATA

WGATE

53

23

O

Write Data. This output is the write precompensated serial data that is written to the

selected disk drive. Precompensation is software selectable.

52

22

Write Gate. This output signal enables the write circuitry of the selected disk drive.

WGATE has been designed to prevent glitches during power up and power down. This

prevents writing to the disk when power is cycled.

WP

1

5

38

42

7

I

Write Protect. This input indicates that the disk in the selected drive is write protected.

Write. Active low input to signal a write from the microprocessor to the controller.

WR

XTAL1/CLK

33

Crystal1/Clock. One side of an external 24 MHz crystal is attached here. If a crystal is

not used, a TTL or CMOS compatible clock is connected to this pin.

XTAL2

34

8

I

Crystal2. One side of an external 24 MHz crystal is attached here. This pin is left

unconnected if an external clock is used.

Note 1: When converting the 68 pin PLCC to a 60 pin PQFP, eight pins were removed. The following signals were affected in this conversion process:

1. NC (No Connect) signals on pins 42 and 43 of the 68 pin PLCC were converted to GND (Ground) signals on pins 14 and 15 of the 60 pin PQFP,

respectively.

2. NC (No Connect) signals on pins 44 and 47 of the 68 pin PLCC were removed for the 60 pin PQFP.

3. HIFIL (pin 38) and LOFIL (pin 37) of the 68 pin PLCC were removed for the 60 pin PQFP.

4. PLL0 (pin 39) and PLL1 (pin 40) of the 68 PLCC were converted to GND (ground) signals on the PQFP (pins 11 and 12 respectively).

5. The GND (ground) signals on pins 9, 12, 21, and 65 of the 68 pin PLCC are not available for the 60 pin PQFP. These signals are tied to ground internally.

8

3.0 Register Description

The following PC8477B registers are mapped into the ad-

dresses shown below, with the base address range being

provided by the CS pin. For PC-AT or PS/2 applications, the

diskette controller primary address range is 3F0 to 3F7

(hex), and the secondary address range is 370 to 377 (hex).

The PC8477B supports three different register modes: the

PC-AT mode, PS/2 mode (Models 50/60/80), and the Mod-

el 30 mode (Model 30). See Section 5.1 for more details on

how each register mode is enabled. When applicable, the

register definition for each mode of operation will be given.

If no special notes are made, then the register is valid for all

three register modes.

TABLE 3-1. Register Description and Addresses

A2

A1

A0

IDENT

R/W

Register

Status Register A

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

R

SRA

SRB

DOR

TDR

MSR

DSR

FIFO

Status Register B

X

R/W

R

Digital Output Register

Tape Drive Register

Main Status Register

Data Rate Select Register

Data Register (FIFO)

None (Bus TRI-STATE)

Digital Input Register

Configuration Control Register

W

R/W

X

R

DIR

W

CCR

e

Note: SRA and SRB are enabled by IDENT

0 during a chip reset only.

3.1 STATUS REGISTER A (SRA) Read Only

3.1.2 SRAÐ Model 30 Mode

This is a read only diagnostic register that is part of the

PS/2 floppy controller register set, and is enabled when in

the PS/2 or Model 30 mode. This register monitors the state

of the INT pin and some of the disk interface signals. The

state of these bits is independent of the INVERT pin. The

SRA can be read at any time when in PS/2 mode. In the

PC-AT mode, D7–D0 are TRI-STATE during a mP read.

D7

D6

D5

D4

D3

D2 D1 D0

INT

DESC

DRQ STEP TRK0 HDSEL INDX WP DIR

PEND

RESET

COND

0

N/A

1

N/A N/A

1

D7

D6

D5

Interrupt Pending: This active high bit reflects

that state of the INT pin.

3.1.1 SRAÐPS/2 Mode

D7

D6

D5

D4

D3

D2 D1 D0

DMA Request: Active high status of the DRQ

signal.

INT

DESC

DRV2 STEP TRK0 HDSEL INDX WP DIR

Step: Active high status of the latched STEP

disk interface output. This bit is latched with the

STEP output going active, and is cleared with a

read from the DIR, or with a hardware or soft-

ware reset.

PEND

RESET

COND

0

N/A

0

N/A

0

N/A N/A 0

D7

D6

Interrupt Pending: This active high bit reflects

the state of the INT pin.

D4

D3

D2

D1

D0

Track 0: Active high status of TRK0 disk inter-

face input.

2nd Drive Installed: Active low status of the

DRV2 disk interface input, indicating if a second

drive has been installed.

Head Select: Active low status of the HDSEL

disk interface output.

Index: Active high status of the INDEX disk in-

terface input.

D5

D4

D3

D2

D1

D0

Step: Active high status of the STEP disk inter-

face output.

Write Protect: Active high status of the WP

disk interface input.

Track 0: Active low status of the TRK0 disk in-

terface input.

Direction: Active low status of the DIR disk in-

terface output.

Head Select: Active high status of the HDSEL

disk interface output.

Index: Active low status of the INDEX disk in-

terface input.

3.2 STATUS REGISTER B (SRB) Read Only

This is a read only diagnostic register that is part of the

PS/2 floppy controller register set, and is enabled when in

the PS/2 or Model 30 mode. The state of these bits is inde-

pendent of the INVERT pin. The SRB can be read at any

time when in PS/2 mode. In the PC-AT mode, D7–D0 are

TRI-STATE during a mP read.

Write Protect: Active low status of the WP disk

interface input.

Direction: Active high status of the DIR disk in-

terface output.

9

3.0 Register Description (Continued)

3.2.1 SRBÐPS/2 Mode

3.3 DIGITAL OUTPUT REGISTER (DOR) Read/Write

The DOR controls the drive select and motor enable disk

interface outputs, enables the DMA logic, and contains a

software reset bit. The contents of the DOR are set to 00

(hex) after a hardware reset, and are unaffected by a soft-

ware reset. The DOR can be written to at any time.

D7 D6 D5

D4

D3

D2

D1

D0

DESC

1

DR0 WDATA RDATA WGATE MTR1 MTR0

RESET

COND

N/A N/A

0

DOR

D7

D6

D5

Reserved: Always 1.

D7

D6

D5

D4

D3

D2

D1

D0

DRIVE DRIVE

SEL 1 SEL 0

Drive Select 0: Reflects the status of the Drive

Select 0 bit in the DOR (address 2, bit 0). This

bit is cleared after a hardware reset, not a soft-

ware reset.

DESC MTR3 MTR2 MTR1 MTR0 DMAEN RESET

RESET

0

COND

D4

D3

Write Data: Every inactive edge transition of

the WDATA disk interface output causes this bit

to change states.

D7

Motor Enable 3: This bit controls the MTR3

disk interface output. A 1 in this bit causes the

MTR3 pin to go active. The actual level of

MTR3 depends on the state of the INVERT pin.

Read Data: Every positive edge transition of the

RDATA disk interface output causes this bit to

change states.

D6

D5

D4

D3

Motor Enable 2: Same function as D7 except

for MTR2.

D2

D1

Write Gate: Active high status of the WGATE

disk interface output.

Motor Enable 1: Same function as D7 except

for MTR1.

Motor Enable 1: Active high status of the

MTR1 disk interface output. Low after a hard-

ware reset, unaffected by a software reset.

Motor Enable 0: Same function as D7 except

for MTR0.

DMA Enable: This bit has two modes of opera-

tion. PC-AT mode or Model 30 mode: Writing

a 1 to this bit will enable the DRQ, DAK, INT

D0

Motor Enable 0: Active high status of the

MTR0 disk interface output. Low after a hard-

ware reset, unaffected by a software reset.

and TC pins. Writing

a 0 to this bit will

TRI-STATE DRQ and INT, and disable DAK and

TC. This bit is a 0 after a reset when in these

modes. PS/2 mode: This bit is reserved, and

the DRQ, DAK, INT and TC pins will always be

enabled. During a reset, the DRQ, DAK, and

INT lines will remain enabled, and D3 will be a

0.

3.2.2 SRBÐModel 30 Mode

D7 D6 D5 D4

D3

D2

D1 D0

DESC DRV2 DR1 DR0 WDATA RDATA WGATE DR3 DR2

RESET

N/A

1

0

1

COND

D2

Reset Controller: Writing a 0 to this bit resets

the controller. It will remain in the reset condi-

tion until a 1 is written to this bit. A software

reset does not affect the DSR, CCR, and other

bits of the DOR. A software reset will affect the

Configure and Mode command bits (see Sec-

tion 4.0 Command Set Description). The mini-

mum time that this bit must be low is 100 ns.

Thus, toggling the Reset Controller bit during

consecutive writes to the DOR is an acceptable

method of issuing a software reset.

D7

2nd Drive Installed: Active low status of the

DRV2 disk interface input.

D6

D5

D4

Drive Select 1: Active low status of the DR1

disk interface output.

Drive Select 0: Active low status of the DR0

disk interface output.

Write Data: Active high status of latched

WDATA signal. This bit is latched by the inac-

tive going edge of WDATA and is cleared by a

read from the DIR. This bit is not gated by

WGATE.

D1–D0

Drive Select: These two bits are binary encod-

ed for the four drive selects DR0–DR3, so that

only one drive select output is active at a time.

The actual level of the drive select outputs is

determined by the state of the INVERT pin.

D3

D2

Read Data: Active high status of latched

RDATA signal. This bit is latched by the inactive

going edge of RDATA and is cleared by a read

from the DIR.

It is common programming practice to enable both the mo-

tor enable and drive select outputs for a particular drive.

Table 3-2 below shows the DOR values to enable each of

the four drives.

Write Gate: Active high status of latched

WGATE signal. This bit is latched by the active

going edge of WGATE and is cleared by a read

from the DIR.

TABLE 3-2. Drive Enable Values

D1

D0

Drive Select 3: Active low status of the DR3

disk interface output.

Drive

DOR Value

Drive Select 2: Active low status of the DR2

disk interface output.

0

1

2

3

1C (Hex)

2D

4E

8F

10

3.0 Register Description (Continued)

3.4 DRIVE REGISTER (TDR) Read/Write

D7

Request for Master: Indicates that the control-

ler is ready to send or receive data from the mP

through the FIFO. This bit is cleared immediate-

ly after a byte transfer and will become set

again as soon as the disk controller is ready for

the next byte. During a Non-DMA Execution

phase, the RQM indicates the status of the in-

terrupt pin.

This register is used to assign a particular drive number with

the tape drive support mode of the data separator. All other

logical drives are assigned floppy drive support with the

data separator. Any future reference to the assigned tape

drive will invoke tape drive support. The TDR is unaffected

by a software reset.

TDR

D6

D5

Data I/O (Direction): Indicates whether the

controller is expecting a byte to be written to (0)

or read from (1) the Data Register.

D7 D6 D5 D4 D3 D2

D1

D0

TAPE TAPE

SEL1 SEL0

Non-DMA Execution: Indicates that the con-

troller is in the Execution Phase of a byte trans-

fer operation in the Non-DMA mode. Used for

multiple byte transfers by the mP in the Execu-

tion Phase through interrupts or software poll-

ing.

DESC

X

RESET

COND

N/A N/A N/A N/A N/A N/A

0

D7–D2

D1–D0

Reserved: These bits are ignored when written

to and are TRI-STATE when read.

D4

D3

Command in Progress: This bit is set after the

first byte of the Command Phase is written. This

bit is cleared after the last byte of the Result

Phase is read. If there is no Result Phase in a

command, the bit is cleared after the last byte

of the Command Phase is written.

Tape Select 1,0: These two bits assign a logical

drive number to be a tape drive. Drive 0 is not

available as a tape drive, and is reserved as the

floppy disk boot drive. See Table 3-3 for the

tape drive assignment values.

Drive 3 Busy: Set after the last byte of the

Command Phase of a Seek or Recalibrate com-

mand is issued for drive 3. Cleared after reading

the first byte in the Result Phase of the Sense

Interrupt Command for this drive.

TABLE 3-3. Tape Drive Assignment Values

DRIVE

TAPESEL1

TAPESEL0

SELECTED

0

1

0

1

0

1

None

D2

D1

D0

Drive 2 Busy: Same as above for drive 2.

Drive 1 Busy: Same as above for drive 1.

Drive 0 Busy: Same as above for drive 0.

1

2

3

3.6 DATA RATE SELECT REGISTER (DSR) Write Only

3.5 MAIN STATUS REGISTER (MSR) Read Only

This write only register is used to program the data rate,

amount of write precompensation, power down mode, and

software reset. The data rate is programmed via the CCR,

not the DSR, for PC-AT and PS/2 Model 30 and MicroChan-

nel applications. Other applications can set the data rate in

the DSR. The data rate of the floppy controller is deter-

mined by the most recent write to either the DSR or CCR.

The DSR is unaffected by a software reset. A hardware re-

set will set the DSR to 02 (hex), which corresponds to the

default precompensation setting and 250 kb/s.

The read only Main Status Register indicates the current

status of the disk controller. The Main Status Register is

always available to be read. One of its functions is to control

the flow of data to and from the Data Register (FIFO). The

Main Status Register indicates when the disk controller is

ready to send or receive data through the Data Register. It

should be read before each byte is transferred to or from

the Data Register except during a DMA transfer. No delay is

required when reading this register after a data transfer.

After a hardware or software reset, or recovery from a pow-

er down state, the Main Status Register is immediately avail-

able to be read by the mP. It will contain a value of 00 hex

until the oscillator circuit has stabilized, and the internal reg-

isters have been initialized. When the PC8477B is ready to

receive a new command, it will report an 80 hex to the mP.

The system software can poll the MSR until it is ready. The

worst case time allowed for the MSR to report an 80 hex

value (RQM set) is 2.5 ms after reset or power up.

DSR

D7

D6 D5 D4

D3

D2

D1

D0

S/W LOW

PRE- PRE- PRE-

DESC

0

DRATE1 DRATE0

RESET PWR

COMP2 COMP1 COMP0

RESET

COND

0

1

0

D7

Software Reset: A 1 in this bit location will re-

set the part similar to the DOR RESET (D2) ex-

cept that this software reset is self-clearing.

MSR

D7 D6 D5

D4

D3

D2

D1

D0

D6

Low Power: A 1 to this bit will put the controller

into the Manual Low Power mode. The oscilla-

tor and data separator circuits will be turned off.

Manual Low Power can also be accessed via

the Mode command. The chip will come out of

low power after a software reset, or access to

the Data Register or Main Status Register.

RQM DIO NON CMD DRV3 DRV2 DRV1 DRV0

DMA PROG BUSY BUSY BUSY BUSY

DESC

RESET

COND

0

11

3.0 Register Description (Continued)

D5

Undefined: Should be set to 0.

only the Execution Phase byte transfers use the 16 byte

FIFO. The FIFO is always disabled during the Command

and Result Phases of a controller operation. If the FIFO is

enabled, it will not be disabled after a software reset if the

LOCK bit is set in the Lock Command. After a hardware

reset, the FIFO is disabled to maintain compatibility with PC-

AT systems.

D4–D2

Precompensation Select: These three bits se-

lect the amount of write precompensation the

floppy controller will use on the WDATA disk

interface output. Table 3-4 shows the amount of

precompensation used for each bit pattern. In

most cases, the default values (Table 3-5) can

be used; however, alternate values can be cho-

sen for specific types of drives and media.

Track 0 is the default starting track number for

precompensation. The starting track number

can be changed in the Configure command.

The 16 byte FIFO can be used for DMA, Interrupt, or soft-

ware polling type transfers during the execution of a read,

write, format, or scan command. In addition, the FIFO can

be put into a Burst or Non-Burst mode with the Mode com-

mand. In the Burst mode, DRQ or INT remains active until

all of the bytes have been transferred to or from the FIFO. In

the Non-Burst mode, DRQ or INT is deasserted for 350 ns

to allow higher priority transfer requests to be serviced. The

Mode command can also disable the FIFO for either reads

or writes separately. The FIFO allows the system a larger

latency without causing a disk overrun/underrun error. Typi-

cal uses of the FIFO would be at the 1 Mb/s data rate, or

with multi-tasking operating systems. The default state of

the FIFO is disabled, with a threshold of zero. The default

state is entered after a hardware reset.

D1–D0

Data Rate Select 1,0: These bits determine the

data rate for the floppy controller. See Table 3-6

for the corresponding data rate for each value

of D1, D0. The data rate select bits are unaffect-

ed by a software reset, and are set to 250 kb/s

after a hardware reset.

TABLE 3-4. Write Precompensation Delays

PRECOMP

Precompensation Delay

4

3

2

Data Register (FIFO)

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

0.0 ns

41.7 ns

D7 D6 D5 D4 D3 D2 D1 D0

83.3 ns

[

Data 7:0

]

DESC

125.0 ns

166.7 ns

208.3 ns

250.0 ns

DEFAULT

RESET

COND

Byte Mode

During the Execution Phase of a command involving data

transfer to/from the FIFO, the system must respond to a

data transfer service request based on the following formu-

la:

TABLE 3-5. Default Precompensation Delays

Maximum Allowable Data Transfer Service Time

Data Rate

Precompensation Delay

a

c

b

c

(16 t

ICP

(THRESH

1)

8

t

)

DRP

1 Mb/s

500 kb/s

300 kb/s

250 kb/s

41.7 ns

125.0 ns

This formula is good for all data rates with the FIFO enabled

or disabled. THRESH is a four bit value programmed in the

Configure command, which sets the FIFO threshold. If the

FIFO is disabled, THRESH is zero in the above formula. The

c

last term of the formula, (16

t ) is an inherent delay due

ICP

to the microcode overhead required by the PC8477B. This

delay is also data rate dependent. See Table 6-1 for the

TABLE 3-6. Data Rate Select Encoding

Data Rate Select

Data Rate

MFM

t

and t

times.

ICP

DRP

The programmable FIFO threshold (THRESH) is useful in

adjusting the floppy controller to the speed of the system. In

other words, a slow system with a sluggish DMA transfer

capability would use a high value of THRESH, giving the

system more time to respond to a data transfer service re-

quest (DRQ for DMA mode or INT for Interrupt mode). Con-

versely, a fast system with quick response to a data transfer

service request would use a low value of THRESH.

1

2

FM

1

0

1

0

1

0

1 Mb/s

500 kb/s

300 kb/s

250 kb/s

Illegal

250 kb/s

150 kb/s

125 kb/s

Note: FM mode is not guaranteed through functional testing.

3.7 DATA REGISTER (FIFO) Read/Write

3.8 DIGITAL INPUT REGISTER (DIR) Read Only

The FIFO (read/write) is used to transfer all commands,

data, and status between the mP and the PC8477B. During

the Command Phase, the mP writes the command bytes into

the FIFO after polling the RQM and DIO bits in the MSR.

During the Result Phase, the mP reads the result bytes from

the FIFO after polling the RQM and DIO bits in the MSR.

This diagnostic register is used to detect the state of the

DSKCHG disk interface input and some diagnostic signals.

The function of this register depends on the register mode

of operation. When in the PC-AT mode, the D6–D0 are

TRI-STATE to avoid conflict with the fixed disk status regis-

ter at the same address. The DIR is unaffected by a soft-

ware reset.

The enabling of the FIFO and setting of the FIFO threshold

is done via the Configure command. If the FIFO is enabled,

12

3.0 Register Description (Continued)

3.8.1 DIRÐPC-AT Mode

3.9.1 CCRÐPC-AT and PS/2 Modes

D7 D6 D5 D4 D3 D2

D1

D0

D7

D6

D5

D4

D3

D2

D1

D0

DESC

0

DRATE1 DRATE0

DESC DSKCHG

X

RESET

COND

N/A N/A N/A N/A N/A N/A

1

0

RESET

N/A

COND

N/A N/A N/A N/A N/A N/A N/A

D7–D2

D1–D0

Reserved: Should be set to 0.

D7

Disk Changed: Active high status of DSKCHG

disk interface input, independent of INVERT

value.

Data Rate Select 1,0: These bits determine the

data rate of the floppy controller. See Table 3-6

for the appropriate values.

D6–D0

Undefined: TRI-STATE. Used by hard disk con-

troller status register.

3.9.2 CCRÐModel 30 Mode

D7 D6 D5 D4 D3

D2

D1

D0

3.8.2 DIRÐPS/2 Mode

DESC

0

0 NOPRE DRATE1 DRATE0

D7

D6 D5 D4 D3

D2

D1

D0

RESET

COND

N/A N/A N/A N/A N/A

0

1

0

HIGH

DEN

DESC DSKCHG

1

DRATE1 DRATE0

D7–D3

D2

Reserved: Should be set to 0.

RESET

N/A

COND

N/A N/A N/A N/A

N/A

1

No Precompensation: This bit can be set by

software, but it has no functionality. It can be

read by bit D2 of the DIR when in the Model 30

register mode. Unaffected by a software reset.

D7

Disk Changed: Active high status of DSKCHG

disk interface input, independent of INVERT

value.

D1–D0

Data Rate Select 1,0: These bits determine the

data rate of the floppy controller. See Table 3-6

for the appropriate values.

D6–D3

D2–D1

Reserved: Always 1.

Data Rate Select 1,0: These bits indicate the

status of the DRATE1–0 bits programmed

through the DSR/CCR.

3.10 RESULT PHASE STATUS REGISTERS

The Result Phase of a command contains bytes that hold

status information. The format of these bytes are described

below. Do not confuse these status bytes with the Main

Status Register, which is a read only register that is always

valid. The Result Phase status registers are read from the

Data Register (FIFO) only during the Result Phase of certain

commands (see Section 4.1 Command Set Summary). The

status of each register bit is indicated when the bit is a 1.

D0

High Density: This bit is low when the 1 Mb/s

or 500 kb/s data rate is chosen, and high when

the 300 kb/s or 250 kb/s data rate is chosen.

This bit is independent of the IDENT or INVERT

value.

3.8.3 DIRÐModel 30 Mode

D7

D6 D5 D4

D3

D2

D1

D0

3.10.1 Status Register 0 (ST0)

DESC DSKCHG

0

DMAEN NOPRE DRATE1 DRATE0

RESET

N/A

COND

D7 D6 D5 D4 D3

D2

D1

D0

0

1

0

DESC

IC

0

IC SE EC

0

HDS DS1 DS0

D7

Disk Changed: Active low status of DSKCHG

disk interface input, independent of INVERT

value.

RESET

COND

0

D7–D6

Interrupt Code:

D6–D4

D3

Reserved: Always 0.

e

00

01

Normal Termination of Command.

DMA Enable: Active high status of the DMAEN

bit in the DOR.

Abnormal Termination of Command. Exe-

cution of command was started, but was

not successfully completed.

D2

No Precompensation: Active high status of the

NOPRE bit in the CCR.

e

10

11

Invalid Command Issued. Command is-

sued was not recognized as a valid com-

mand.

D1–D0

Data Rate Select 1,0: These bits indicate the

status of the DRATE1–0 bits programmed

through the DSR/CCR.

Internal drive ready status changed state

during the drive polling mode. Only occurs

after a hardware or software reset.

3.9 CONFIGURATION CONTROL REGISTER (CCR) Write

Only

D5

D4

D3

Seek End: Seek, Relative Seek, or Recalibrate

command completed by the controller. (Used

during a Sense Interrupt command.)

This is the write only data rate register commonly used in

PC-AT applications. This register is not affected by a soft-

ware reset, and is set to 250 kb/s after a hardware reset.

The data rate of the floppy controller is determined by the

last write to either the CCR or DSR.

Equipment Check: After a Recalibrate com-

mand, Track 0 signal failed to occur. (Used dur-

ing Sense Interrupt command.)

Not Used. Always 0.

13

3.0 Register Description (Continued)

D2

Head Select: Indicates the active high status of

the HDSEL pin at the end of the Execution

Phase.

3.10.3 Status Register 2 (ST2)

D7 D6 D5 D4

D3

D2

D1 D0

DESC

0

CM CD WT SEH SNS BT MD

D1–D0

Drive Select 1,0: These two binary encoded

bits indicate the logical drive selected at the end

of the Execution Phase.

RESET

COND

0

e

00

01

10

11

Drive 0 selected.

Drive 1 selected.

Drive 2 selected.

Drive 3 selected.

D7

Not Used. Always 0.

D6

Control Mark: Controller tried to read a sector

which contained a deleted data address mark

during execution of Read Data or Scan com-

mands. Or, if a Read Deleted Data command

was executed, a regular address mark was de-

tected.

3.10.2 Status Register 1 (ST1)

D7 D6 D5 D4 D3 D2

D1

D0

DESC

ET

0

CE OR

0

ND NW MA

D5

D4

CRC Error in Data Field: Controller detected a

CRC error in the Data Field. Bit 5 of ST1 is also

set.

RESET

COND

0

Wrong Track: Only set if desired sector is not

found, and the track number recorded on any

sector of the current track is different from the

track address specified in the Command Phase.

D7

End of Track: Controller transferred the last

byte of the last sector without the TC pin be-

coming active. The last sector is the End of

Track sector number programmed in the Com-

mand Phase.

D3

D2

Scan Equal Hit: ‘‘Equal’’ condition satisfied dur-

ing any Scan command.

D6

D5

Not Used. Always 0.

Scan Not Satisfied: Controller cannot find a

sector on the track which meets the desired

condition during any Scan command.

CRC Error: If this bit is set and bit 5 of ST2 is

clear, then there was a CRC error in the Ad-

dress Field of the correct sector. If bit 5 of ST2

is also set, then there was a CRC error in the

Data Field.

D1

D0

Bad Track: Only set if the desired sector is not

found, the track number recorded on any sector

on the track is FF (hex) indicating a hard error in

IBM format, and is different from the track ad-

dress specified in the Command Phase.

D4

Overrun: Controller was not serviced by the mP

soon enough during a data transfer in the Exe-

cution Phase. For read operations, indicates a

data overrun. For write operations, indicates a

data underrun.

Missing Address Mark in Data Field: Control-

ler cannot find the Data Field AM during a Read,

Scan, or Verify command. Bit 0 of ST1 is also

set.

D3

D2

Not Used. Always 0.

No Data: Three possible problems:

1. Controller cannot find the sector specified in

the Command Phase during the execution of

a Read, Write, Scan, or Verify command. An

address mark was found however, so it is not

a blank disk.

3.10.4 Status Register 3 (ST3)

D7 D6 D5 D4 D3

D2

D1

D0

DESC

0

WP

0

1

TK0

0

1

HDS DS1 DS0

RESET

COND

0

2. Controller cannot read any Address Fields

without a CRC error during a Read ID com-

mand.

D7

Not Used. Always 0.

D6

Write Protect: Indicates active high status of

the WP pin.

3. Controller cannot find starting sector during

execution of Read A Track command.

D5

D4

Not Used. Always 1.

D1

D0

Not Writable: Write Protect pin is active when a

Write or Format command is issued.

Track 0: Indicates active high status of the

TRK0 pin.

Missing Address Mark: If bit 0 of ST2 is clear

then the controller cannot detect any Address

Field Address Mark after two disk revolutions. If

bit 0 of ST2 is set then the controller cannot

detect the Data Field Address Mark after finding

the correct Address Field.

D3

D2

Not Used. Always 1.

Head Select: Indicates the active high status of

the HD bit in the Command Phase.

D1–D0

Drive Select 1,0: These two binary encoded

bits indicate the DS1–DS0 bits in the Command

Phase.

14

4.0 Command Set Description

The following is a table of the PC8477B command set. Each

command contains a unique first command byte called the

opcode byte which will identify to the controller how many

command bytes to expect. If an invalid command byte is

issued to the controller, it will immediately go into the Result

Phase and the status will be 80 (hex), which signifies Invalid

Command.

Result Phase

Status Register 0

Status Register 1

Status Register 2

Undefined

4.1 COMMAND SET SUMMARY

Undefined

CONFIGURE

Command Phase

Undefined

INVALID

Command Phase

0

1

0

1

0

1

0

Invalid Op Codes

EIS

FIFO

POLL

PRETRK

THRESH

Result Phase

Status Register 0 (80 hex)

Execution Phase: Internal registers written.

No Result Phase

LOCK

Command Phase

LOCK

0

1

0

1

0

DUMPREG

Command Phase

Execution Phase: Internal register is written.

0

1

0

Result Phase

Execution Phase: Internal registers read.

0

LOCK

0

Result Phase

MODE

Command Phase

PTR Drive 0

PTR Drive 1

PTR Drive 2

PTR Drive 3

0

1

ETR

0

TMR

IAF

IPS

LOW PWR

1

0

FWR FRD BST R255

DENSEL BFR WLD

0

Step Rate Time

Motor On Time

Sectors per Track/End of Track

DC3 DC2 DC1 DC0 GAP WG

EIS FIFO POLL THRESH

PRETRK

Motor Off Time

Head Settle

RG

DMA

0

O

PU

Execution Phase: Internal registers are written.

LOCK

0

No Result Phase

NSC

Command Phase

Note: Sectors per Track parameter returned if last command issued was

Format. End of Track parameter returned if last command issued was Read

or Write.

0

1

0

1

Result Phase

FORMAT TRACK

Command Phase

0

1

0

MFM

X

0

1

0

1

PERPENDICULAR MODE

Command Phase

X

HD

DR1

DR0

Bytes per Sector

Sectors per Track

Format Gap

0

1

0

1

0

OW

DC3

DC2

DC1

DC0

GAP

WG

Execution Phase: Internal registers are written.

Data Pattern

No Result Phase

Execution Phase: System transfers four ID bytes (track,

head, sector, bytes/sector) per sector to the floppy control-

ler via DMA or Non-DMA modes. The entire track is format-

ted. The data block in the Data Field of each sector is filled

with the data pattern byte.

15

4.0 Command Set Description (Continued)

READ DATA

Command Phase

Result Phase

Status Register 0

Status Register 1

Status Register 2

Track Number

MT

IPS

MFM

X

SK

X

0

1

0

X

HD

DR1

DR0

Track Number

Drive Head Number

Sector Number

Head Number

Sector Number

Bytes per Sector

End of Track Sector Number

Intersector Gap Length

Data Length

READ A TRACK

Command Phase

Execution Phase: Data read from disk drive is transferred

to system via DMA or Non-DMA modes.

0

MFM

X

0

1

0

IPS

X

HD

DR1

DR0

Result Phase

Track Number

Status Register 0

Status Register 1

Status Register 2

Track Number

Drive Head Number

Sector Number

Bytes per Sector

End of Track Sector Number

Intersector Gap Length

Data Length

Head Number

Sector Number

Bytes per Sector

Execution Phase: Data read from disk drive is transferred

to system via DMA or Non-DMA modes.

READ DELETED DATA

Command Phase

Result Phase

Status Register 0

Status Register 1

Status Register 2

Track Number

MT

IPS

MFM

X

SK

X

0

1

0

X

HD

DR1

DR0

Track Number

Drive Head Number

Sector Number

Head Number

Sector Number

Bytes per Sector

End of Track Sector Number

Intersector Gap Length

Data Length

RECALIBRATE

Command Phase

Execution Phase: Data read from disk drive is transferred

to system via DMA or Non-DMA modes.

0

1

0

1

DR1

DR0

Result Phase

Execution Phase: Disk drive head is stepped out to

Track 0.

Status Register 0

Status Register 1

Status Register 2

Track Number

No Result Phase

RELATIVE SEEK

Command Phase

Head Number

1

DIR

X

0

1

Sector Number

Bytes per Sector

X

HD

DR1

DR0

Relative Track Number

Execution Phase: Disk drive head stepped in or out a

programmable number of tracks.

READ ID

Command Phase

No Result Phase

0

MFM

X

0

1

0

1

0

X

HD

DR1

DR0

Execution Phase: Controller reads first ID Field header

bytes it can find and reports these bytes to the system in the

result bytes.

16

4.0 Command Set Description (Continued)

SCAN EQUAL

Command Phase

SCAN LOW OR EQUAL

Command Phase

MT

IPS

MFM

X

SK

X

1

0

1

MT

IPS

MFM

X

SK

X

1

0

1

X

HD

DR1

DR0

X

HD

DR1

DR0

Track Number

Drive Head Number

Sector Number

Drive Head Number

Sector Number

Bytes per Sector

End of Track Sector Number

Intersector Gap Length

Sector Step Size

End of Track Sector Number

Intersector Gap Length

Sector Step Size

Execution Phase: Data transferred from system to

controller is compared to data read from disk.

Execution Phase: Data transferred from system to

controller is compared to data read from disk.

Result Phase

Status Register 0

Status Register 1

Status Register 2

Track Number

Status Register 0

Status Register 1

Status Register 2

Track Number

Head Number

Sector Number

Bytes per Sector

Sector Number

Bytes per Sector

SEEK

Command Phase

SCAN HIGH OR EQUAL

Command Phase

0

1

MT

IPS

MFM

X

SK

X

1

0

1

X

HD DR1 DR0

X

HD

DR1

DR0

New Track Number

MSN of Track Number

Track Number

0

Drive Head Number

Sector Number

Note: Last Command Phase byte is required only if ETR is set in Mode

Command.

Execution Phase: Disk drive head is stepped in or out to a

programmable track.

Bytes per Sector

End of Track Sector Number

Intersector Gap Length

Sector Step Size

No Result Phase

SENSE DRIVE STATUS

Command Phase

Execution Phase: Data transferred from system to

controller is compared to data read from disk.

0

1

0

X

HD

DR1

DR0

Result Phase

Execution Phase: Disk drive status information is detected

and reported.

Status Register 0

Status Register 1

Status Register 2

Track Number

Result Phase

Status Register 3

Head Number

SENSE INTERRUPT

Command Phase

Sector Number

Bytes per Sector

0

1

0

Execution Phase: Status of interrupt is reported.

Result Phase

Status Register 0

Present Track Number (PTR)

MSN of PTR

0

Note: Third Result Phase byte can only be read if ETR is set in the Mode

Command.

17

4.0 Command Set Description (Continued)

SET TRACK

Command Phase

WRITE DATA

Command Phase

0

WNR

0

1

0

1

0

1

MT

IPS

MFM

X

0

1

0

1

MSB

DR1

DR0

X

HD

DR1

DR0

New Track Number (PTR)

Track Number

Drive Head Number

Sector Number

Execution Phase: Internal register is read or written.

Result Phase

Bytes per Sector

Value

End of Track Sector Number

Intersector Gap Length

Data Length

SPECIFY

Command Phase

Execution Phase: Data is transferred from the system to

the controller via DMA or Non-DMA modes and written to

the disk.

0

1

Step Rate Time

Motor On Time

Motor Off Time

DMA

Result Phase

Execution Phase: Internal registers are written.

Status Register 0

Status Register 1

Status Register 2

Track Number

No Result Phase

VERIFY

Command Phase

Head Number

MT

EC

MFM

X

SK

X

1

0

1

0

Sector Number

Bytes per Sector

X

HD

DR1

DR0

Track Number

Drive Head Number

Sector Number

WRITE DELETED DATA

Command Phase

Bytes per Sector

MT

IPS

MFM

X

0

1

0

1

End of Track Sector Number

Intersector Gap Length

Data Length/Sector Count

X

HD

DR1

DR0

Track Number

Drive Head Number

Sector Number

Execution Phase: Data is read from disk but not transferred

to the system.

Bytes per Sector

Result Phase

End of Track Sector Number

Intersector Gap Length

Data Length

Status Register 0

Status Register 1

Status Register 2

Track Number

Execution Phase: Data is transferred from the system to

the controller via DMA or Non-DMA modes and written to

the disk.

Head Number

Sector Number

Bytes per Sector

Result Phase

Status Register 0

Status Register 1

Status Register 2

Track Number

VERSION

Command Phase

0

1

0

Head Number

Result Phase

Sector Number

Bytes per Sector

1

0

18

4.0 Command Set Description (Continued)

4.2 COMMAND DESCRIPTION

4.2.2 Dumpreg Command

The Dumpreg command is designed to support system run-

time diagnostics and application software development and

debug. This command has a one byte command phase and

a ten byte result phase, which return the values of parame-

ters set in other commands. That is, the PTR (Present Track

Register) contains the least significant byte of the track the

microcode has stored for each drive. The Step Rate Time,

Motor Off and Motor On Times, and the DMA bit are all set

in the Specify command.

4.2.1 Configure Command

The Configure Command will control some operation modes

of the controller. It should be issued during the initialization

of the PC8477B after power up. The function of the bits in

the Configure registers is described below. These bits are

set to their default values after a hardware reset. The value

of each bit after a software reset is explained. The default

value of each bit is denoted by a ‘‘bullet’’ to the left of each

item.

The sixth byte of the result phase varies depending on

which commands have been previously executed. If a for-

mat command has previously been issued, and no reads or

writes have been issued since then, then this byte will con-

tain the Sectors per track value. If a read or a write com-

mand has been executed more recently than a format com-

mand, this byte will contain the End of Track value. The

LOCK bit is set in the Lock command. The eighth result byte

also contains the bits programmed in the Perpendicular

Mode command. The last two bytes of the Dumpreg Result

Phase are set in the Configure command. After a hardware

or software reset, the parameters in the result bytes will be

set to their appropriate default values.

EIS: Enable Implied Seeks. Default after a software reset.

e

0

Implied seeks disabled through Configure command.

Implied seeks can still be enabled through the Mode

#

e

command when EIS

0. (default)

e

1

Implied seeks enabled for a read, write, scan, or veri-

fy operation. A seek and sense interrupt operation

will be performed prior to the execution of the read,

write, scan, or verify operation. The IPS bit does not

need to be set.

FIFO: Enable FIFO for Execution Phase data transfers. De-

fault after a software reset if the LOCK bit is 0. If the LOCK

bit is 1, then the FIFO bit will retain its previous value after a

software reset.

Note: Some of these parameters are unaffected by a software reset, de-

pending on the state of the LOCK bit.

e

0

1

FIFO enabled for both reads and writes.

FIFO disabled. (default)

4.2.3 Format Track Command

#

This command will format one track on the disk in IBM, ISO,

or Perpendicular Format. After the index hole is detected,

data patterns are written on the disk including all Gaps, Ad-

dress Marks, Address Fields, and Data Fields. The exact

format is determined by the following parameters:

POLL: Disable for Drive Polling Mode. Default after a soft-

ware reset.

e

0

1

Enable polling mode. An interrupt is generated after

a reset. (default)

#

e

Disable drive polling mode. If the Configure com-

mand is issued within 500 ms of a hardware or soft-

ware reset, then an interrupt will not be generated. In

addition, the four Sense Interrupt commands to clear

the ‘‘Ready Changed State’’ of the four logical drives

will not be required.

1. The MFM bit in the Opcode (first command) byte, which

determines the format of the Address Marks and the en-

coding scheme.

2. The IAF bit in the Mode command, which selects be-

tween IBM and ISO format.

3. The WGATE and GAP bits in the Perpendicular Mode

command, which select between the conventional and

Toshiba Perpendicular format.

THRESH: The FIFO threshold in the Execution Phase of

read and write data transfers. Programmable from 00 to 0F

hex. Defaults to 00 after a software reset if the LOCK bit is

0. If the LOCK bit is 1, then THRESH will retain its value. A

high value of THRESH is suited for slow response systems,

and a low value of THRESH is better for fast response sys-

tems.

4. The Bytes per Sector code, which determines the sector

size.

5. The Sectors per Track parameter, which determines how

many sectors will be formatted on the track.

PRETRK: Starting track number for write precompensation.

Programmable from track 0 (‘‘00’’) to track 255 (‘‘FF’’). De-

faults to track 0 (‘‘00’’) after a software reset if the LOCK bit

is 0. If the LOCK bit is 1, then PRETRK will retain its value.

6. The Data Pattern byte, which is used as the filler byte in

the Data Field of each sector.

To allow for flexible formatting, the mP must supply the four

Address Field bytes (track, head, sector, bytes per sector

code) for each sector formatted during the Execution

Phase. This allows for non-sequential sector interleaving.

This transfer of bytes from the mP to the controller can be

done in the DMA or Non-DMA mode, with the FIFO enabled

or disabled.

19

4.0 Command Set Description (Continued)

TL/F/11332–4

Notes:

e

FE*

FC*

FB*

F8*

A1*

C2*

Data Pattern of FE, Clock Pattern of C7

Data Pattern of FC, Clock Pattern of D7

Data Pattern of FB, Clock Pattern of C7

Data Pattern of F8, Clock Pattern of C7

Data Pattern of A1, Clock Pattern of 0A

Data Pattern of C2, Clock Pattern of 14

All byte counts in decimal

All byte values in hex

16

12

5

a a

x

a

Two byte CRC uses standard polynomial x

x

1

FM mode is not guaranteed through functional testing.

e

Perpendicular Format GAP2

All other data rates use GAP2

41 bytes for 1 Mb/s

e

22 bytes

FIGURE 4-1. IBM, Perpendicular, and ISO Formats Supported by Format Command

20

4.0 Command Set Description (Continued)

The Format command terminates when the index hole is

detected a second time, at which point an interrupt is gener-

ated. Only the first three status bytes in the Result Phase

are significant. The Format Gap byte in the Command

Phase is dependent on the data rate and type of disk drive,

and will control the length of GAP3. Some typical values for

the programmable GAP3 are given in Table 4-1 below. Fig-

ure 4-1 shows the track format for the different formats rec-

ognized by the Format Command.

4.2.4 Invalid Command

If an invalid command (illegal Opcode byte in the Command

Phase) is received by the controller, the controller will re-

spond with ST0 in the Result Phase. The controller does not

generate an interrupt during this condition. Bits 6 and 7 in

the MSR are both set to a 1, indicating to the mP that the

controller is in the Result Phase and the contents of ST0

must be read. The system will read an 80 (hex) value from

ST0 indicating an invalid command was received.

TABLE 4-1. Typical Format Gap Length Values

Sector

Size

Sector

Code

Sector

Gap

Format

GAP3

Mode

EOT

Hex

Decimal

Hex

125 kb/s

FM

128

256

512

1024

2048

00

01

02

03

04

12

10

08

04

02

01

07

10

18

46

C8

09

19

30

87

FF

250 kb/s

MFM

256

512

1024

2048

4096

01

02

03

04

05

12

10

08

09

04

02

01

0A

20

2A

80

C8

0C

32

50

F0

FF

250 kb/s

FM

128

256

512

1024

2048

4096

00

01

02

03

04

05

1A

0F

08

04

02

01

07

0E

1B

47

C8

1B

2A

3A

8A

FF

500 kb/s

MFM

256

512

1024

2048

4096

8192

01

02

03

04

05

06

1A

0F

12

08

04

02

01

0E

1B

35

99

C8

36

54

6C

74

FF

Note: FM mode is not guaranteed through functional testing.

Typical Values for PC Compatible Diskette Media

Media

Type

Sector

Size

Sector

EOT

Code

Sector

Gap

Format

GAP

Decimal

Hex

360K

1.2M

512

02

09

0F

09

12

24

2A

1B

50

54

50

6C

53

720K

1.44M

2.88M

Notes:

Sector Gap refers to the Intersector Gap Length parameter specified in the Command Phase of the Read, Write, Scan, and Verify commands. Although this is the

recommended value, the PC8477B treats this byte as a don’t care in the Read, Write, Scan, and Verify commands.

Format Gap is the suggested value to use in the Format Gap parameter of the Format command. This is the programmable GAP3 as shown in Figure 4-1.

The 2.88M diskette media is a new Barium Ferrite media intended for use in Perpendicular Recording drives at the data rate of up to 1 Mb/s.

21

4.0 Command Set Description (Continued)

4.2.5 Lock Command

ETR: Extended Track Range. Default after a software reset.

e

The Lock command allows the user full control of the FIFO

parameters after a software reset. If the LOCK bit is set to 1,

then the FIFO, THRESH, and PRETRK bits in the Configure

command are not affected by a software reset. In addition,

the FWR, FRD, and BST bits in the Mode command will be

unaffected by a software reset. If the LOCK is 0 (default

after a hardware reset), then the above bits will be set to

their default values after a software reset. This command is

useful if the system designer wishes to keep the FIFO en-

abled and retain the other FIFO parameter values (such as

THRESH) after a software reset.

0

Track number is stored as a standard 8-bit value

compatible with the IBM, ISO, and Perpendicular

formats. This will allow access to up to 256 tracks

during a seek operation.

#

e

1

Track number is stored as a 12-bit value. The up-

per four bits of the track value are stored in the

upper four bits of the head number in the sector

Address Field. This allows access to up to 4096

tracks during a seek operation. With this bit set, an

extra byte is required in the Seek Command

Phase and Sense Interrupt Result Phase.

After the command byte is written, the result byte must be

read before continuing to the next command. The execution

of the Lock command is not performed until the result byte

is read by the mP. If the part is reset after the command byte

is written but before the result byte is read, then the Lock

command execution will not be performed. This is done to

prevent accidental execution of the Lock command.

FWR: FIFO Write Disable for mP write transfers to control-

ler. Default after a software reset if LOCK is 0. If LOCK is 1,

FWR will retain its value after a software reset.

Note: This bit is only valid if the FIFO is enabled in the Configure command.

If the FIFO is not enabled in the Configure command, then this bit is a

don’t care.

e

0

Enable FIFO. Execution Phase mP write transfers

use the internal FIFO. (default)

#

4.2.6 Mode Command

e

1

Disable FIFO. All write data transfers take place

without the FIFO.

This command is used to select the special features of the

controller. The bits for the Command Phase bytes are

shown in Section 4.1 Command Set Summary, and their

function is described below. These bits are set to their de-

fault values after a hardware reset. The default value of

each bit is denoted by a ‘‘bullet’’ to the left of each item. The

value of each parameter after a software reset will be ex-

plained.

FRD: FIFO Read Disable for mP read transfer from control-

ler. Default after a software reset if LOCK is 0. If LOCK is 1,

FRD will retain its value after a software reset.

Note: This bit is only valid if the FIFO is enabled in the Configure command.

If the FIFO is not enabled in the Configure command, then this bit is a

don’t care.

e

0

Enable FIFO. Execution Phase mP read transfer

use the internal FIFO. (default)

#

TMR: Motor Timer mode. Default after a software reset.

e

0

Timers for motor on and motor off are defined for

Mode 1. (See Specify command.) (default)

#

e

1

Disable FIFO. All read data transfers take place

without the FIFO.

e

1

Timers for motor on and motor off are defined for

Mode 2. (See Specify command.)

BST: Burst Mode Disable. Default after a software reset if

LOCK is 0. If LOCK is 1, BST will retain its value after a

software reset.

IAF: Index Address Format. Default after a software reset.

e

0

The controller will format tracks with the Index Ad-

dress Field included. (IBM and Perpendicular for-

mat.)

#

Note: This bit is only valid if the FIFO is enabled in the Configure command.

If the FIFO is not enabled in the Configure command, then this bit is a

don’t care.

e

0

Burst mode enabled for FIFO Execution Phase

data transfers. (default)

#

e

1

The controller will format tracks without including

the Index Address Field. (ISO format.)

e

1

Non-Burst mode enabled. The DRQ or INT pin will

be strobed once for each byte to be transferred

while the FIFO is enabled.

IPS: Implied Seek. Default after a software reset.

e

0

The implied seek bit in the command byte of a

read, write or scan is ignored. Implied seeks could

still be enabled by the EIS bit in the Configure

command.

#

R255: Recalibrate Step Pulses. The bit will determine the

maximum number of recalibrate step pulses the controller

will issue before terminating with an error. Default after a

software reset.

e

1

The IPS bit in the command byte of a read, write

or scan is enabled so that if it is set, the controller

will perform seek and sense interrupt operations

before executing the command.

e

1,

0

85 maximum recalibrate step pulses. If ETR

#

controller will issue 3925 recalibrate step pulses

maximum.

LOW PWR: Low Power mode. Default after a software

reset.

e

1

255 maximum recalibrate step pulses. If ETR

1,

controller will issue 4095 maximum recalibrate

step pulses.

e

00

01

Completely disable the low power mode. (default)

#

Automatic low power. Go into low power mode

512 ms after the head unload timer times out. This

is based on 500 kb/s or 1 Mb/s data rate. Double

this value for 250 kb/s.

DENSEL: Density Select Pin Configuration. This two bit val-

ue will configure the Density Select output to one of three

possible modes. The default mode will configure the DEN-

SEL pin according to the state of the IDENT input pin after a

data rate has been selected. That is, if IDENT is high, the

DENSEL pin is active high for the 500 kb/s or 1 Mb/s data

rates.

e

10

11

Manual low power. Go into low power mode now.

Not used.

22

4.0 Command Set Description (Continued)

e

If IDENT is low, the DENSEL pin is active low for the

500 kb/s or 1 Mb/s data rates. In addition to these modes,

the DENSEL output can be set to always low or always high,

as shown in Table 4-2. This will allow the user more flexibili-

ty with new drive types.

1

Enable the MFM output to act as the active low out-

put of the Data Separator charge pump. This signal

consists of a series of pulses indicating when the

phase comparator is making a phase correction.

This Pump output will be active low for a pump up or

pump down signal from the phase comparator, and

is intended as a test mode to aid in the evaluation of

the Data Separator.

Note: The DENSEL output values shown below are with the INVERT pin

tied low. If the INVERT pin is tied high, the outputs shown below have

the opposite polarity.

TABLE 4-2. DENSEL Decoding

4.2.7 NSC Command

Bit 1

Bit 0

DENSEL Pin Definition

The NSC command can be used to distinguish between the

PC8477B version and the Intel 82077AA. The result Phase

byte uniquely identifies the floppy controller as a PC8477B,

which returns a value of 73 hex. The 82077AA and DP8473

return a value 80h signifying an invalid command. The lower

four bits of this result byte are subject to change by NSC,

and will reflect the particular version of the PC8477B part.

0

1

0

1

0

1

low

high

undefined

DEFAULT

TABLE 4-3. DENSEL Default Encoding

DENSEL (default)

Note: The PC8477A will return a value of 72h in the result phase of the

NSC command.

Data Rate

e

0

IDENT

1

IDENT

4.2.8 Perpendicular Mode Command

The Perpendicular Mode command is designed to support

the unique Format and Write Data requirements of Perpen-

dicular (Vertical) Recording disk drives (4 Mbytes unformat-

ted capacity). The Perpendicular Mode command will con-

figure each of the four logical drives as a perpendicular or

conventional disk drive. Configuration of the four logical disk

drives is done via the D3–D0 bits, or with the GAP and WG

control bits. This command should be issued during the ini-

tialization of the floppy controller.

250 kb/s

300 kb/s

500 kb/s

1 Mb/s

low

high

low

high

BFR: CMOS Disk Interface Buffer Enable.

e

0

Drive output signals configured as standard 4 mA

4 mA

#

push-pull outputs (actually 48 mA sink,

source). (default)

Perpendicular Recording drives operate in ‘‘Extra High Den-

sity’’ mode at 1 Mb/s, and are downward compatible with

1.44 Mbyte and 720 kbyte drives at 500 kb/s (High Density)

and 250 kb/s (Double Density) respectively. If perpendicular

drives are present in the system, this command should be

issued during initialization of the floppy controller, which will

configure each drive as perpendicular or conventional.

Then, when a drive is accessed for a Format or Write Data

command, the floppy controller will adjust the Format or

Write Data parameters based on the data rate (see Table

4-4).

e

1

Drive output signals configured as 48 mA open-

drain outputs.

WLD: Scan Wild Card.

e

0

An FF (hex) from either the mP or the disk during a

Scan command is interpreted as a wildcard charac-

ter that will always match true. (default)

#

e

1

The Scan commands do not recognize FF (hex) as

a wildcard character.

Head Settle: Time allowed for read/write head to settle af-

ter a seek during an Implied Seek operation.

Looking at the second command byte, DC3–DC0 corre-

spond to the four logical drives. A ‘‘0’’ written to DCn sets

drive n to conventional mode, and a ‘‘1’’ sets drive n to

perpendicular mode. Also, the OW (Overwrite) bit offers ad-

e

Data Rate

HST

N x 8

Range

250 kb/s

300 kb/s

500 kb/s

1 Mb/s

0–120 ms

0–100 ms

0–60 ms

0–30 ms

N x 6.67

N x 4

ditional control. When OW

1, changing the values of

DC3–DC0 (drive configuration bits) is enabled. When

e

regardless of what is written to DC3–DC0.

OW

0, the internal values of DC3–DC0 are unaffected,

N x 2

e

Head Settle Time

Note: N

8 (default)

HST

The function of the DCn bits must also be qualified by set-

ting both WG and GAP to 0. If WG and GAP are used (i.e.,

not set to 00), they will override whatever is programmed in

the DCn bits. Table 4-4A indicates the operation of the

PC8477B based on the values of GAP and WG. Note that

when GAP and WG are both 0, the DCn bits are used to

configure each logical drive as conventional or perpendicu-

lar. DC3–DC0 are unaffected by a software reset, but WG

and GAP are both cleared to 0 after a software reset. A

hardware reset will reset all the bits to zero (conventional

mode for all drives). The Perpendicular Mode command bits

may be rewritten at any time.

RG: Read Gate Diagnostic.

e

0

Enable DSKCHG disk interface input for normal op-

eration. (default)

#

e

1

Enable DSKCHG to act as an external Read Gate

input signal to the Data Separator. This is intended

as a test mode to aid in evaluation of the Data Sep-

arator.

PU: PUMP Pulse Output Diagnostic.

e

0

Enable MFM output pin for normal operation. (de-

fault)

#

Note: When in the Perpendicular Mode for any drive at any data rate via the

DC3–DC0 bits, write precompensation is set to zero.

23

4.0 Command Set Description (Continued)

TABLE 4-4. Effect of Drive Mode and Data Rate on Format and Write Commands

GAP2 Length

Written During

Format

Portion of GAP2

Re-Written by Write

Data Command

Drive

Mode

Data Rate

250/300/500 kb/s

1 Mb/s

Conventional

Perpendicular

22 bytes

0 bytes

19 bytes

Conventional

Perpendicular

22 bytes

41 bytes

0 bytes

38 bytes

TABLE 4-4A. Effect of GAP and WG on Format and Write Commands

GAP2 Length

Mode

Portion of GAP2

Re-Written by Write

Data Command

GAP

WG

Written During

Format

Description

0

1

Conventional

Perpendicular

22 bytes

0 bytes

19 bytes

s

(

500 kb/s)

1

0

1

Reserved

22 bytes

41 bytes

0 bytes

(Conventional)

Perpendicular

(1 Mb/s)

38 bytes

Perpendicular Recording type disk drives have a Pre-Erase

Head which leads the Read/Write Head by 200 mm, which

translates to 38 bytes at the 1 Mb/s data transfer rate (19

bytes at 500 kb/s). The increased spacing between the two

heads requires a larger GAP2 between the Address Field

and Data Field of a sector at 1 Mb/s. (See Perpendicular

Format in Table 4-1.) This GAP2 length of 41 bytes (at

1 Mb/s) will ensure that the Preamble in the Data Field is

completely ‘‘pre-erased’’ by the Pre-Erase Head. Also, dur-

ing Write Data operations to a perpendicular drive, a portion

of GAP2 must be rewritten by the controller to guarantee

that the Data Field Preamble has been pre-erased (see Ta-

ble 4-4).

TABLE 4-5. Sector Size Selection

Bytes per

Number of Bytes

in Data Field

Sector Code

0

1

2

3

4

5

6

7

128

256

512

1024

2048

4096

8192

16384

4.2.9 Read Data Command

The controller then starts the Data Separator and waits for

the Data Separator to find the next sector Address Field.

The controller compares the Address Field ID information

(track, head, sector, bytes per sector) with the desired ID

specified in the Command Phase. If the sector ID bytes do

not match, then the controller waits for the Data Separator

to find the next sector Address Field. The ID comparison

process repeats until the Data Separator finds a sector Ad-

dress Field ID that matches that in the command bytes, or

until an error occurs. Possible errors are:

The Read Data command reads logical sectors containing a

Normal Data AM from the selected drive and makes the

data available to the host mP. After the last Command

Phase byte is written, the controller will simulate the Motor

On Time for the selected drive internally. The user must turn

on the drive motor directly by enabling the appropriate drive

and motor select disk interface outputs with the Digital Out-

put Register (DOR).

If Implied Seeks are enabled, the controller will perform a

Seek operation to the track number specified in the Com-

mand Phase. The controller will also issue a Sense Interrupt

for the seek and wait the Head Settle time specified in the

Mode command.

1. The mP aborted the command by writing to the FIFO. If

there is no disk in the drive, the controller will hang up.

The mP must then take the controller out of this hung

state by writing a byte to the FIFO. This will put the con-

troller into the Result Phase.

The correct ID information (track, head, sector, bytes per

sector) for the desired sector must be specified in the com-

mand bytes. See Table 4-5 Sector Size Selection for details

on the bytes per sector code. In addition, the End of Track

Sector Number (EOT) should be specified, allowing the con-

troller to read multiple sectors. The Data Length byte is a

don’t care and should be set to FF (hex).

2. Two index pulses were detected since the search began,

and no valid ID has been found. If the track address ID

differs, the WT bit or BT bit (if the track address is FF hex)

will be set in ST2. If the head, sector, or bytes per sector

code did not match, the ND bit is set in ST1. If the Ad-

dress Field AM was never found, the MA bit is set in ST1.

3. The Address Field was found with a CRC error. The CE

bit is set in ST1.

24

4.0 Command Set Description (Continued)

Once the desired sector Address Field is found, the control-

ler waits for the Data Separator to find the subsequent Data

Field for that sector. If the Data Field (normal or deleted) is

not found with the expected time, the controller terminates

the operation and enters the Result Phase (MD is set in

ST2). If a Deleted Data Mark is found and SK was set in the

Opcode command byte, the controller skips this sector and

searches for the next sector Address Field as described

above. The effect of SK on the Read Data command is

summarized in Table 4-6.

3. Overrun error. The OR bit in ST1 is set. The IC bits in ST0

are set to Abnormal Termination. If the mP cannot service

a transfer request in time, the last correctly read byte will

be transferred.

4. CRC error. The CE bit in ST1 and CD bit in ST2 are set.

The IC bits in ST0 are set to Abnormal Termination.

If MT was set in the Opcode command byte, and the last

sector of side 0 has been transferred, the controller will then

continue with side 1, starting with sector 1 and continuing

until EOT sector number is reached or TC occurs.

Having found the Data Field, the controller then transfers

data bytes from the disk drive to the host (described in Sec-

tion 5.3 Controller Phases) until the bytes per sector count

has been reached, or the host terminates the operation

(through TC, end of track, or implicitly through overrun). The

controller will then generate the CRC for the sector and

compare this value with the CRC at the end of the Data

Field.

Upon terminating the Execution Phase of the Read Data

command, the controller will assert INT, indicating the be-

ginning of the Result Phase. The mP must then read the

result bytes from the FIFO. The values that will be read back

in the result bytes are shown in Table 4-7. If an error occurs,

the result bytes will indicate the sector read when the error

occurred.

4.2.10 Read Deleted Data Command

Having finished reading the sector, the controller will contin-

ue reading the next logical sector unless one or more of the

following termination conditions occurred:

The Read Deleted Data command reads logical sectors

containing a Deleted Data AM from the selected drive and

makes the data available to the host mP. This command is

identical to the Read Data command, except for the setting

of the CM bit in ST2 and the skipping of sectors. The effect

of SK on the Read Deleted Data command is summarized in

Table 4-8. See Table 4-7 for the state of the result bytes for

a Normal Termination of the command.

1. The DMA controller asserted TC. The IC bits in ST0 are

set to Normal Termination.

2. The last sector address (of side 1 if MT was set) was

equal to EOT. The EOT bit in ST1 is set. The IC bits in

ST0 are set to Abnormal Termination. This is the expect-

ed condition during Non-DMA transfers.

TABLE 4-6. SK Effect on Read Data Command

Sector Read? CM Bit (ST2)

SK

0

Data Type

Normal

Description of Results

Normal Termination

No Further Sectors Read

Normal Termination

Sector Skipped

Y

0

Deleted

Normal

Y

N

1

0

1

Deleted

TABLE 4-7. Result Phase Termination Values with No Error

ID Information at Result Phase

MT

HD

Last Sector

Track

Head

NC

H

Sector

Bytes/Sector

k

a

0

1

0

1

0

1

EOT

NC

S

1

NC

e

k

e

k

e

k

e

a

EOT

T

1

a

NC

a

1

a

NC

a

0

1

a

NC

H

a

0

1

e

EOT

End of Track Sector Number from Command Phase

T

Track Number programmed in Command Phase

Head last selected by controller

e

NC

No Change in Value

H

e

S

Sector Number last operated on by controller

TABLE 4-8. SK Effect on Read Deleted Data Command

SK

0

Data Type

Normal

Sector Read?

CM Bit (ST2)

Description of Results

No Further Sectors Read

Normal Termination

Sector Skipped

Y

N

Y

1

0

1

0

Deleted

Normal

1

Deleted

Normal Termination

25

4.0 Command Set Description (Continued)

4.2.11 Read ID Command

brate step pulse values based on the R255 and ETR bits in

the Mode command. If the number of tracks on the disk

drive exceeds the maximum number of recalibrate step

pulses, another Recalibrate command may need to be is-

sued.

The Read ID command finds the next available Address

Field and returns the ID bytes (track, head, sector, bytes per

sector) to the mP in the Result Phase. There is no data

transfer during the Execution Phase of this command. An

interrupt will be generated when the Execution Phase is

completed.

TABLE 4-9. Maximum Recalibrate Step

Pulses Based on R255 and ETR

The controller first simulates the Motor On time for the se-

lected drive internally. The user must turn on the drive motor

directly by enabling the appropriate drive and motor select

disk interface outputs with the Digital Output Register

(DOR). The Read ID command does not perform an implied

seek.

Maximum Recalibrate

R255

ETR

Step Pulses

0

1

0

1

0

1

85 (default)

255

3925

After waiting the Motor On time, the controller starts the

Data Separator and waits for the Data Separator to find the

next sector Address Field. If an error condition occurs, the

IC bits in ST0 are set to Abnormal Termination, and the

controller enters the Result Phase. Possible errors are:

4095

After the last command byte is issued, the DRx BUSY bit is

set in the MSR for the selected drive. The controller will

simulate the Motor On time, and then enter the Idle Phase.

The execution of the actual step pulses occurs while the

controller is in the Drive Polling Phase. An interrupt will be

generated after the TRK0 signal is asserted, or after the

maximum number of recalibrate step pulses are issued.

There is no Result Phase. Recalibrates on more than one

drive at a time should not be issued for the same reason as

explained in the Seek command. No other command except

the Sense Interrupt command should be issued while a Re-

calibrate command is in progress.

1. The mP aborted the command by writing to the FIFO. If

there is no disk in the drive, the controller will hang up.

The mP must then take the controller out of this hung

state by writing a byte to the FIFO. This will put the con-

troller into the Result Phase.

2. Two index pulses were detected since the search began,

and no AM has been found. If the Address Field AM was

never found, the MA bit is set in ST1.

4.2.12 Read A Track Command

4.2.14 Relative Seek Command

The Read a Track command reads sectors in physical order

from the selected drive and makes the data available to the

host. This command is similar to the Read Data command

except for the following differences:

The Relative Seek command steps the selected drive in or

out a given number of steps. This command will step the

read/write head an incremental number of tracks, as op-

posed to comparing against the internal present track regis-

ter for that drive. The Relative Seek parameters are defined

as follows:

1. The controller waits for the index pulse before searching

for a sector Address Field. If the mP writes to the FIFO

before the index pulse, the command will enter the Result

Phase with the IC bits in ST0 set to Abnormal Termina-

tion.

DIR: Read/Write Head Step Direction Control

e

0

1

Step Head Out

Step Head In

2. A comparison of the sector Address Field ID bytes will be

performed, except for the sector number. The internal

sector address is set to 1, and then incremented for each

successive sector read.

RTN: Relative Track Number. This value will determine how

many incremental tracks to step the head in or out

from the current track number.

The controller will issue RTN number of step pulses and

update the Present Track Register for the selected drive.

The one exception to this is if the TRK0 disk input goes

active, which indicates that the drive read/write head is at

the outermost track. In this case, the step pulses for the

Relative Seek are terminated, and the PTR value is set ac-

cording to the actual number of step pulses issued. The

arithmetic is done modulo 255. The DRx BUSY bit in the

MSR is set for the selected drive. The controller will simu-

late the Motor On time before issuing the step pulses. After

the Motor On time, the controller will enter the Idle Phase.

The execution of the actual step pulses occurs in the Idle

Phase of the controller.

3. If the Address Field ID comparison fails, the controller

sets ND in ST1, but continues to read the sector. If there

is a CRC error in the Address Field, the controller sets CE

in ST1, but continues to read the sector.

4. Multi-track and Skip operations are not allowed. SK and

MT should be set to 0.

5. If there is a CRC error in the Data Field, the controller

sets CE in ST1 and CD in ST2, but continues reading

sectors.

6. The controller reads a maximum of EOT physical sectors.

There is no support for multi-track reads.

4.2.13 Recalibrate Command

After the step operation is complete, the controller will gen-

erate an interrupt. There is no Result Phase. Relative Seeks

on more than one drive at a time should not be issued for

the same reason as explained in the Seek command. No

other command except the Sense Interrupt command

should be issued while a Relative Seek command is in prog-

ress.

The Recalibrate command is very similar to the Seek com-

mand. The controller sets the Present Track Register (PTR)

of the selected drive to zero. It then steps the head of the

selected drive out until the TRK0 disk interface input signal

goes active, or until the maximum number of step pulses

have been issued. See Table 4-9 for the maximum recali-

26

4.0 Command Set Description (Continued)

4.2.15 Scan Commands

command except a Sense Interrupt command should be is-

sued while a Seek command is in progress.

The Scan commands allow data read from the disk to be

compared against data sent from the mP. There are three

Scan commands to choose from:

If the extended track range mode is enabled with the ETR

bit in the Mode command, a fourth command byte should be

written in the Command Phase to indicate the four most

significant bits of the desired track number. Otherwise, only

three command bytes should be written.

e

mP Data

Scan Equal

Scan Low or Equal

Scan High or Equal

Disk Data

s

Disk Data mP Data

t

Disk Data mP Data

Each sector is interpreted with the most significant bytes

first. If the Wildcard mode is enabled in the Mode command,

an FF (hex) from either the disk or the mP is used as a don’t

care byte that will always match equal. After each sector is

read, if the desired condition has not been met, the next

sector is read. The next sector is defined as the current

sector number plus the Sector Step Size specified. The

Scan command will continue until the scan condition has

been met, or the EOT has been reached, or if TC is assert-

ed.

4.2.17 Sense Drive Status Command

The Sense Drive Status command returns the status of the

selected disk drive in ST3. This command does not gener-

ate an interrupt.

4.2.18 Sense Interrupt Command

The Sense Interrupt command is used to determine the

cause of interrupt when the interrupt is a result of the

change in status of any disk drive. Four possible causes of

the interrupt are:

Read errors on the disk will have the same error conditions

as the Read Data command. If the SK bit is set, sectors with

deleted data marks are ignored. If all sectors read are

skipped, the command will terminate with D3 of ST2 set

(Scan Equal Hit). The Result Phase of the command is

shown in Table 4-10.

1. Upon entering the Result Phase of:

a. Read Data command

b. Read Deleted Data command

c. Read a Track command

d. Read ID command

e. Write Data command

f. Write Deleted Data command

g. Format command

TABLE 4-10. Scan Command Termination Values

Status

h. Scan command

i. Verify command

Register 2

Command

Conditions

2. During data transfers in the Execution Phase while in the

Non-DMA mode.

D2

D3

e

mP

Scan Equal

0

1

0

Disk

3. Ready Changed State during the polling mode for an in-

ternally selected drive. (Occurs only after a hardware or

software reset.)

i

Disk mP

e

mP

Scan Low

or Equal

0

1

0

Disk

4. Seek, Relative Seek, or Recalibrate termination.

k

Disk mP

l

An interrupt due to reasons 1 and 2 does not require the

Sense Interrupt command and is cleared automatically. This

interrupt occurs during normal command operations and is

easily discernible by the mP via the MSR. This interrupt is

cleared reading or writing information from/to the Data Reg-

ister (FIFO).

Disk mP

e

mP

Scan High

or Equal

0

1

0

Disk

k

Disk mP

l

Disk mP

4.2.16 Seek Command

Interrupts caused by reason 3 and 4 are identified with the

aid of the Sense Interrupt command. The interrupt is cleared

after the first result byte has been read. Use bits 5, 6, and 7

of ST0 to identify the cause of the interrupt as shown in

Table 4-11.

The Seek command issues step pulses to move the select-

ed drive head in or out until the desired track number is

reached. During the Execution Phase of the Seek com-

mand, the track number to seek to is compared with the

present track number. The controller will determine how

many step pulses to issue and the DIR disk interface output

will indicate which direction the R/W head should move.

The DRx BUSY bit is set in the MSR for the appropriate

drive. The controller will wait the Motor On time before issu-

ing the first step pulse.

TABLE 4-11. Status Register 0 Termination Codes

Status Register 0

Interrupt

Code

Seek

End

Cause

After the Motor On time, the controller will enter the Idle

Phase. The execution of the actual step pulses occurs in the

Drive Polling phase of the controller. The step pulse rate is

determined by the value programmed in the Specify com-

mand. An interrupt will be generated one step pulse period

after the last step pulse is issued. There is no Result Phase.

A Sense Interrupt command should be issued to determine

the cause of the interrupt.

D7

D6

D5

0

1

Internal Ready Went True

Normal Seek Termination

Abnormal Seek Termination

0

1

Issuing a Sense Interrupt command without an interrupt

pending is treated as an Invalid command. If the extended

track range mode is enabled, a third byte should be read in

the Result Phase, which will indicate the four most signifi-

cant bits of the present track number. Otherwise, only two

result bytes should be read.

While the internal microengine is capable of multiple seeks

on 2 or more drives at the same time, software should en-

sure that only one drive is seeking or recalibrating at a time.

This is because the drives are actually selected via the

DOR, which can only select one drive at a time. No other

27

4.0 Command Set Description (Continued)

4.2.19 Set Track Command

Motor Off Time: These four bits determine the simulated

Motor Off time as shown in Table 4-14.

This command is used to inspect or change the value of the

internal Present Track Register. This could be useful for re-

covery from disk mis-tracking errors, where the real current

track could be read through the Read ID command, and

then the Set Track command could be used to set the inter-

nal Present Track Register to the correct value.

TABLE 4-14. Motor Off Time (MFT) Values

e

Mode 1 (TMR

0)

Mode 2 (TMR

1)

Data

Rate

Units

Value

Range

Value

Range

1 Mb/s MFT x 8

8–128

MFT x 512

512–8192

ms

If the WNR bit is a 0, a track register is to be read. In this

case, the Result Phase byte contains the value in the inter-

nal register specified, and the third byte in the Command

Phase is a dummy byte.

500 kb/s MFT x 16

16–256 MFT x 512

300 kb/s MFT x 80/3 26.7–427 MFT x 2560/3 853–13653

250 kb/s MFT x 32 32–512 MFT x 1024

1024–16384 ms

e

16.

Note: MFT

0 is treated as Motor Off Time

If the WNR bit is a 1, data is written to a track register. In this

case the third byte of the Command Phase is written to the

specified internal track register, and the Result Phase byte

contains this new value written.

Motor On Time: These seven bits determine the simulated

Motor On time as shown in Table 4-15.

TABLE 4-15. Motor On Time (MNT) Values

The DS1 and DS0 bits select the Present Track Register for

the particular drive. The internal register address depends

on MSB, DS1, and DS0 as shown in Table 4-12. This com-

mand does not generate an interrupt.

e

1)

Mode 1 (TMR

0)

Mode 2 (TMR

Value Range

Data

Rate

Units

Value

Range

1 Mb/s

MNT

1–128

MNT x 32 32–4096 ms

500 kb/s

TABLE 4-12. Set Track Register Address

300 kb/s MNT x 10/3 3.3–427 MNT x 160/3 53–6827 ms

DS1

DS0

MSB

Register Addressed

250 kb/s MNT x 4

4–512

MNT x 64 64–8192 ms

0

1

0

1

0

1

0

1

0

1

0

1

0

1

PTR0(LSB)

PTR0(MSB)

PTR1(LSB)

PTR1(MSB)

PTR2(LSB)

PTR2(MSB)

PTR3(LSB)

PTR3(MSB)

e

Note 1: MNT

0 is treated as Motor On Time

128.

e

Note 2: For PC8477A at 500 kb/s when TMR

0 the value is MNT x 2 and

range is 2–256.

DMA: This bit selects the data transfer mode in the Execu-

tion Phase of a read, write, or scan operation.

0

1

DMA mode is selected.

Non-DMA mode is selected.

4.2.21 Verify Command

4.2.20 Specify Command

The Verify command reads logical sectors containing a Nor-

mal Data AM from the selected drive without transferring

the data to the host. This command is identical to the Read

Data command, except that no data is transferred during

the Execution Phase.

The Specify command sets the initial values for three inter-

nal timers. The function of these Specify parameters is de-

scribed below. The parameters of this command are unde-

fined after power up, and are unaffected by any reset. Thus,

software should always issue a Specify command as part of

an initialization routine. This command does not generate

an interrupt.

The Verify command is designed for post-format or post-

write verification. Data is read from the disk, as the control-

ler checks for valid Address Marks in the Address and Data

Fields. The CRC is computed and checked against the pre-

viously stored value on the disk. The EOT value should be

set to the final sector to be checked on each side. If EOT is

greater than the number of sectors per side, the command

will terminate with an error and no useful Address Mark or

CRC data will be given.

The Motor Off and Motor On timers are artifacts of the

mPD765. These timers determine the delay from selecting a

drive motor until a read or write operation is started, and the

delay of deselecting the drive motor after the command is

completed. Since the PC8477B enables the drive and motor

select line directly through the DOR, these timers only pro-

vide some delay from the initiation of a command until it is

actually started.

The TC pin cannot be used to terminate this command

since no data is transferred. The command can simulate a

TC by setting the EC bit to a 1. In this case, the command

will terminate when SC (Sector Count) sectors have been

Step Rate Time: These four bits define the time interval

between successive step pulses during a seek, implied

seek, recalibrate, or relative seek. The programming of this

step rate is shown in Table 4-13.

e

0 then 256 sectors will be verified.) If EC

read. (If SC

0, then the command will terminate when EOT is equal to

the last sector to be checked. In this case, the Data Length

parameter should be set to FF hex. Refer to Table 4-7 for

the Result Phase values for a successful completion of the

command. Also see Table 4-16 for further explanation of

the result bytes with respect to the MT and EC bits.

TABLE 4-13. Step Rate Time (SRT) Values

Data Rate

Value

Range

0.5–8

Units

1 Mb/s

500 kb/s

300 kb/s

250 kb/s

(16-SRT) x 0.5

(16-SRT)

ms

1–16

(16-SRT) x 1.67

(16-SRT) x 2

1.67–26.7

2–32

28

4.0 Command Set Description (Continued)

TABLE 4-16. Verify Command Result Phase Table

MT

EC

SC/EOT Value

Termination Result

0

DTL used (should be FF hex)

s

No Errors

Ý

EOT

Sectors per Side

0

1

DTL used (should be FF hex)

l

Abnormal Termination

No Errors

Ý

EOT

Sectors per Side

s

Ý

SC

Sectors per Side

AND

s

SC EOT

l

Ý

0

1

SC

Sectors Remaining

OR

Abnormal Termination

l

SC EOT

1

0

1

DTL used (should be FF hex)

s

No Errors

Ý

EOT

Sectors per Side

DTL used (should be FF hex)

l

Abnormal Termination

No Errors

Ý

EOT

Sectors per Side

s

Ý

SC

Sectors per Side

AND

s

SC EOT

s

SC (EOT x 2)

1

No Errors

AND

s

Ý

EOT

Sectors per Side

l

SC (EOT x 2)

Abnormal Termination

e

number of formatted sectors per each side of the disk.

Ý

Note 1:

Note 2:

Sectors per Side

e

1 and the SC value is greater than the number of remaining formatted sectors on side 0, verifying will continue on side 1 of the disk.

Sectors Remaining

e

number of formatted sectors left which can be read, which includes side 1 of the disk if the MT bit is set to 1.

Note 3: If MT

4.2.22 Version Command

2. Two index pulses were detected since the search began,

and no valid ID has been found. If the track address ID

differs, the WT bit or BT bit (if the track address is FF hex)

will be set in ST2. If the head, sector, or bytes per sector

code did not match, the ND bit is set in ST1. If the Ad-

dress Field AM was never found, the MA bit is set in ST1.

The Version command can be used to determine the floppy

controller being used. The Result Phase uniquely identifies

the floppy controller version. The PC8477B returns a value

of 90 hex in order to be compatible with the 82077. The

DP8473 and other NEC765 compatible controllers will re-

turn a value of 80 hex (invalid command).

3. The Address Field was found with a CRC error. The CE

bit is set in ST1.

4.2.23 Write Data Command

4. If the controller detects the Write Protect disk interface

input is asserted, bit 1 of ST1 is set.

The Write Data command receives data from the host and

writes logical sectors containing a Normal Data AM to the

selected drive. The operation of this command is similar to

the Read Data command except that the data is transferred

from the mP to the controller instead of the other way

around.

If the correct Address Field is found, the controller waits for

all (conventional mode) or part (perpendicular mode) of

GAP2 to pass. The controller will then write the preamble

field, address marks, and data bytes to the Data Field. The

data bytes are transferred to the controller by the mP.

The controller will simulate the Motor On time before start-

ing the operation. If implied seeks are enabled, the seek and

sense interrupt functions are then performed. The controller

then starts the Data Separator and waits for the Data Sepa-

rator to find the next sector Address Field. The controller

compares the Address ID (track, head, sector, bytes per

sector) with the desired ID specified in the Command

Phase. If there is no match, the controller waits to find the

next sector Address Field. This process continues until the

desired sector is found. If an error condition occurs, the IC

bits in ST0 are set to Abnormal Termination, and the con-

troller enters the Result Phase. Possible errors are:

Having finished writing the sector, the controller will contin-

ue reading the next logical sector unless one or more of the

following termination conditions occurred:

1. The DMA controller asserted TC. The IC bits in ST0 are

set to Normal Termination.

2. The last sector address (of side 1 if MT was set) was

equal to EOT. The EOT bit in ST1 is set. The IC bits in

ST0 are set to Abnormal Termination. This is the expect-

ed condition during Non-DMA transfers.

3. Underrun error. The OR bit in ST1 is set. The IC bits in

ST0 are set to Abnormal Termination. If the mP cannot

service a transfer request in time, the last correctly writ-

ten byte will be written to the disk.

1. The mP aborted the command by writing to the FIFO. If

there is no disk in the drive, the controller will hang up.

The mP must then take the controller out of this hung

state by writing a byte to the FIFO. This will put the con-

troller into the Result Phase.

29

4.0 Command Set Description (Continued)

If MT was set in the Opcode command byte, and the last

sector of side 0 has been transferred, the controller will then

continue with side 1, starting with sector 1 and continuing

Model 30 ModeÐ(IDENT tied low, MFM pulled low exter-

nally): This mode supports the PS/2 Model 30 configuration

and register set. The DMA enable bit in the Digital Output

Register becomes valid (INT and DRQ can be TRI-STATE).

TC is active high and DENSEL becomes active low (default

Ý

terminattion values listed in Table 4-7.

until EOT Sector

is reached or TC occurs. Result phase

to 3.5 floppy drive).

×

4.2.24 Write Deleted Data

The Write Deleted Data command receives data from the

host and writes logical sectors containing a Deleted Data

AM to the selected drive. This command is identical to the

Write Data command except that a Deleted Data AM is writ-

ten to the Data Field instead of a Normal Data AM.

5.3 CONTROLLER PHASES

The PC8477B has three separate phases of a command,

the Command Phase, the Execution Phase, and the Result

Phase. Each of these controller phases will determine how

data is transferred between the floppy controller and the

host microprocessor. In addition, when no command is in

progress, the controller is in the Idle Phase or Drive Polling

Phase.

5.0 Functional Description

The PC8477B is pin compatible with the 82077AA floppy

disk controller. It is software compatible with the DP8473

and 82077AA floppy disk controllers. Upon a power-on re-

set, the 16 byte FIFO will be disabled. Also, the disk inter-

face outputs will be configured as active push-pull outputs,

which are compatible with both CMOS inputs and open-col-

lector resistor terminated disk drive inputs. The FIFO can be

enabled with the Configure command. The FIFO can be

very useful at the higher data rates, with systems that have

a large amount of DMA bus latency, or with multi-tasking

systems such as the EISA or MCA bus structures.

5.3.1 Command Phase

During the Command Phase, the mP writes a series of bytes

to the Data Register. The first command byte contains the

opcode for the command, and the controller will know how

many more bytes to expect based on this opcode byte. The

remaining command bytes contain the particular parameters

required for the command. The number of command bytes

will vary for each particular command. All the command

bytes must be written in the order specified in the Command

Description Table. The Execution Phase starts immediately

after the last byte in the Command Phase is written. Prior to

performing the Command Phase, the Digital Output Register

should be set and the data rate should be set with the Data

Rate Select Register or Configuration Control Register.

The PC8477B will support all the DP8473 Mode command

features as well as some additional features. These include

control over the enabling of the FIFO for reads and writes, a

Non-Burst mode for the FIFO, a bit that will configure the

disk interface outputs as open-drain outputs, and pro-

grammability of the DENSEL output.

The Main Status Register controls the flow of command

bytes, and must be polled by the software before writing

each Command Phase byte to the Data Register. Prior to

writing a command byte, the RQM bit (D7) must be set and

the DIO bit (D6) must be cleared in the MSR. After the first

command byte is written to the Data Register, the CMD

PROG bit (D4) will also be set and will remain set until the

last Result Phase byte is read. If there is no Result Phase,

the CMD PROG bit will be cleared after the last command

byte is written.

5.1 MICROPROCESSOR INTERFACE

The PC8477B interface to the microprocessor consists of

the CS, RD, and WR lines, which access the chip for reads

and writes; the data lines D7–D0; the address lines A2–A0,

which select the register to be accessed (see Table 3-1);

the INT signal, and the DMA interface signals DRQ, DACK,

and TC. It is through this microprocessor interface that the

floppy controller receives commands, transfers data, and

returns status information.

A new command may be initiated after reading all the result

bytes from the previous command. If the next command

requires selecting a different drive or changing the data rate,

the DOR and DSR or CCR should be updated. If the com-

mand is the last command, then the software should de-

select the drive.

5.2 MODES OF OPERATION

The PC8477B has three modes of operation: PC-AT mode,

PS/2 mode, and Model 30 mode, which are determined by

the state of the IDENT pin and MFM pin. IDENT can be tied

directly to V

or GND. The MFM pin must be tied high or

CC

low with a 10 kX resistor (there is an internal 40 kX–50 kX

resistor on the MFM pin). The state of these pins is interro-

gated by the controller during a chip reset to determine the

mode of operation. See Section 3.0 Register Description for

more details on the register set used for each mode of oper-

ation. After chip reset, the state of IDENT can be changed

to change the polarity of DENSEL (see Section 2.0 Pin De-

scription).

Note: As a general rule, the operation of the controller core is independent

of how the mP updates the DOR, DSR, and CCR. The software must

ensure that the manipulation of these registers is coordinated with the

controller operation.

5.3.2 Execution Phase

During the Execution Phase, the disk controller performs

the desired command. Commands that involve data trans-

fers, such as a read, write, or format operation, will require

the mP to write or read data to or from the Data Register at

this time. Some commands such as a Seek or Recalibrate

will control the read/write head movement on the disk drive

during the Execution Phase via the disk interface signals.

The execution of other commands does not involve any ac-

tion by the mP or disk drive, and consists of an internal

operation by the controller.

PC-AT ModeÐ(IDENT tied high, MFM is a don’t care): The

PC-AT register set is enabled. The DMA enable bit in the

Digital Output Register becomes valid (INT and DRQ can be

TRI-STATE). TC and DENSEL become active high signals

(defaults to a 5.25 floppy drive).

×

PS/2 ModeÐ(IDENT tied low, MFM pulled high internally):

This mode supports the PS/2 Models 50/60/80 configura-

tion and register set. The DMA enable bit in the Digital Out-

put Register becomes a don’t care (INT and DRQ signals

will always be valid). TC and DENSEL become active low

If there is data to be transferred between the mP and the

controller during the Execution, there are three methods

that can be used, DMA mode, interrupt transfer mode, and

signals (default to 3.5 floppy drive).

×

30

5.0 Functional Description (Continued)

software polling mode. The last two modes are called the

Non-DMA modes. The DMA mode is used if the system has

a DMA controller. This allows the mP to do other tasks while

the data transfer takes place during the Execution Phase. If

the Non-DMA mode is used, an interrupt is issued for each

byte transferred during the Execution Phase. Also, instead

of using the interrupt during Non-DMA mode, the Main

Status Register can be polled by software to indicate when

a byte transfer is required. All of these data transfer modes

will work with the FIFO enabled or disabled.

For both the Burst and Non-Burst modes, when the last byte

in the FIFO has been read, DRQ will go inactive. DRQ will

then be reasserted when the FIFO trigger condition is satis-

fied. After the last byte of a sector has been read from the

disk, DRQ is again generated even if the FIFO has not yet

reached its threshold trigger condition. This will guarantee

that all the current sector bytes are read from the FIFO

before the next sector byte transfer begins.

Write Data Transfers

Whenever the number of bytes in the FIFO is less than or

equal to THRESH, a DRQ is generated. This is the trigger

condition for the FIFO write data transfers from the mP to

the floppy controller.

5.3.2.1 DMA ModeÐFIFO Disabled

The DMA mode is selected by writing a 0 to the DMA bit in

the Specify command and by setting the DMA enabled bit

(D3) in the DOR. With the FIFO disabled, a DMA request

(DRQ) is generated in the Execution Phase when each byte

is ready to be transferred. The DMA controller should re-

spond in the DRQ with a DMA acknowledge (DACK) and a

read or write strobe. The DRQ will be cleared by the leading

edge of the active low DACK input signal. After the last byte

is transferred, an interrupt is generated, indicating the begin-

ning of the Result Phase. During DMA operations the chip

select input (CS) must be held high. The DACK signal will

act as the chip select for the FIFO in this case, and the state

of the address lines A2–A0 is a don’t care. The Terminal

Count (TC) signal can be asserted by the DMA controller to

terminate the data transfer at any time. Due to internal gat-

ing, TC is only recognized when DACK is low.

Burst Mode: DRQ will remain active until enough bytes

have been written to the controller to completely fill the

FIFO.

Non-Burst Mode: DRQ will be deasserted after each write

transfer. If the FIFO is not yet full, DRQ will be reasserted

after a 350 ns delay. This deassertion of DRQ will allow

other higher priority DMA transfers to take place between

floppy transfers.

The FIFO has a byte counter which will monitor the number

of bytes being transferred to the FIFO during write opera-

tions for both Burst and Non-Burst modes. When the last

byte of a sector is transferred to the FIFO, DRQ will be

deasserted even if the FIFO has not been completely filled.

In this way, the FIFO will be cleared after each sector is

written. Only after the floppy controller has determined that

another sector is to be written will DRQ be asserted again.

Also, since DRQ is deasserted immediately after the last

byte of a sector is written to the FIFO, the system does not

need to tolerate any DRQ deassertion delay and is free to

do other work.

PC-AT Mode: When in the PC-AT interface mode with the

FIFO disabled, the controller will be in single byte transfer

mode. That is, the system will have one byte time to service

a DMA request (DRQ) from the controller. DRQ will be deas-

serted between each byte.

PS/2 and Model 30 Modes: When in the PS/2 or Model 30

modes, DMA transfers with the FIFO disabled are per-

formed differently. Instead of a single byte transfer mode,

Read and Write Data Transfers

The DACK input signal from the DMA controller may be held

active during an entire burst or it may be strobed for each

byte transferred during a read or write operation. When in

the Burst mode, the floppy controller will deassert DRQ as

soon as it recognizes that the last byte of a burst was trans-

ferred. If DACK is strobed for each byte, the leading edge of

this strobe is used to deassert DRQ. If DACK is strobed, RD

or WR are not required. This is the case during the Read

Verify mode of the DMA Controller. If DACK is held active

during the entire burst, the trailing edge of the RD or WR

strobe is used to deassert DRQ. DRQ will be deasserted

within 50 ns of the leading edge of DACK, RD, or WR. This

quick response should prevent the DMA controller from

transferring extra bytes in most applications.

e

the FIFO will actually be enabled with THRESH

0F (hex).

Thus, DRQ will be asserted when one byte has entered the

FIFO during reads, and when one byte can be written to the

FIFO during writes. DRQ will be deasserted by the leading

edge of the DACK input, and will be reasserted when DACK

goes inactive high. This operation is very similar to Burst

mode transfer with the FIFO enabled except that DRQ is

deasserted between each byte.

5.3.2.2 DMA ModeÐFIFO Enabled

Read Data Transfers

Whenever the number of bytes in the FIFO is greater than

b

or equal to (16 THRESH), a DRQ is generated. This is the

trigger condition for the FIFO read data transfers from the

Overrun Errors

floppy controller to the mP.

An overrun or underrun error will terminate the execution of

the command if the system does not transfer data within the

allotted data transfer time (see Section 3.7), which will put

the controller into the Result Phase. During a read overrun,

the mP is required to read the remaining bytes of the sector

before the controller will assert INT, signifying the end of

execution. During a write operation, an underrun error will

terminate the Execution Phase after the controller has writ-

ten the remaining bytes of the sector with the last correctly

written byte to the FIFO and generated the CRC bytes.

Whether there is an error or not, an interrupt is generated at

the end of the Execution Phase, and is cleared by reading

the first Result Phase byte.

Burst Mode: DRQ will remain active until enough bytes

have been read from the controller to empty the FIFO.

Non-Burst Mode: DRQ will be deasserted after each read

transfer. If the FIFO is not completely empty, DRQ will be

reasserted after a 350 ns delay. This will allow other higher

priority DMA transfers to take place between floppy trans-

fers. In addition, this mode will allow the controller to work

correctly in systems where the DMA controller is put into a

read verify mode, where only DACK signals are sent to the

FDC, with no RD pulses. This read verify mode of the DMA

controller is used in some PC software. The FIFO Non-Burst

mode allows the DACK input from the DMA controller to be

strobed, which will correctly clock data from the FIFO.

31

5.0 Functional Description (Continued)

DACK asserted by itself without a RD or WR strobe is also

counted as a transfer. If RD or WR are not being strobed for

each byte, then DACK must be strobed for each byte so that

the floppy controller can count the number of bytes correct-

ly. A new command, the Verify command, has been added

to allow easier verification of data written to the disk without

the need of actually transferring the data on the data bus.

signal. Otherwise, the data transfer is similar to the Interrupt

Mode described above. This is true for the FIFO enabled or

disabled.

5.3.3 Result Phase

During the Result Phase, the mP reads a series of bytes

from the data register. These bytes indicate the status of the

command. This status may indicate whether the command

executed properly, or contain some control information (see

the Command Description Table and Status Register De-

scription). These Result Phase bytes are read in the order

specified for that particular command. Some commands will

not have a result phase. Also, the number of result bytes

varies with each command. All of the result bytes must be

read from the Data Register before the next command can

be issued.

5.3.2.3 Interrupt ModeÐFIFO Disabled

If the Interrupt (Non-DMA) mode is selected, INT is asserted

instead of DRQ when each byte is ready to be transferred.

The Main Status Register should be read to verify that the

interrupt is for a data transfer. The RQM and NON DMA bits

(D7 and D5) in the MSR will be set. The interrupt will be

cleared when the byte is transferred to or from the Data

Register. CS and RD or CS and WR must be used to trans-

fer the data in or out of the Data Register (A2–A0 must be

valid). CS asserted by itself is not significant. CS must be

asserted with RD or WR for a read or write transfer to be

recognized.

Like the Command Phase, the Main Status Register con-

trols the flow of result bytes, and must be polled by the

software before reading each Result Phase byte from the

Data Register. The RQM bit (D7) and DIO bit (D6) must both

be set before each result byte can be read. After the last

result byte is read, the COM PROG bit (D4) in the MSR will

be cleared, and the controller will be ready for the next com-

mand.

The mP should transfer the byte within the data transfer

service time (see Section 3.7). If the byte is not transferred

within the time allotted, an Overrun Error will be indicated in

the Result Phase when the command terminates at the end

of the current sector.

5.3.4 Idle Phase

An interrupt will also be generated after the last byte is

transferred. This indicates the beginning of the Result

Phase. The RQM and DIO bits (D7 and D6) in the MSR will

be set, and the NON DMA bit (D5) will be cleared. This

interrupt is cleared by reading the first result byte.

After a hardware or software reset, or after the chip has

recovered from the power down mode, the controller enters

the Idle Phase. Also, when there are no commands in prog-

ress the controller will be in the Idle Phase. The controller

will be waiting for a command byte to be written to the Data

Register. The RQM bit will be set and the DIO bit will be

cleared in the MSR. After receiving the first command (op-

code) byte, the controller will enter the Command Phase.

When the command is completed the controller again en-

ters the Idle Phase. The Data Separator will remain synchro-

nized to the reference frequency while the controller is idle.

While in the Idle Phase, the controller will periodically enter

the Drive Polling Phase (see below).

5.3.2.4 Interrupt ModeÐFIFO Enabled

The Interrupt (Non-DMA) mode with the FIFO enabled is

very similar to the Non-DMA mode with the FIFO disabled.

In this case, INT is asserted instead of DRQ under the exact

same FIFO threshold trigger conditions. The MSR should be

read to verify that the interrupt is for a data transfer. The

RQM and NON DMA bits (D7 and D5) in the MSR will be

set. CS and RD or CS and WR must be used to transfer the

data in or out of the Data Register (A2–A0 must be valid).

CS asserted by itself is not significant. CS must be asserted

with RD or WR for a read or write transfer to be recognized.

5.3.5 Drive Polling Phase

While in the Idle Phase the controller will enter a Drive Poll-

ing Phase every 1 ms (based on the 500 kb/s data rate).

While in the Drive Polling Phase, the controller will interro-

gate the Ready Changed status for each of the four logical

drives. The internal Ready line for each drive is toggled only

after a hardware or software reset, and an interrupt will be

generated for drive 0. At this point, the software must issue

four Sense Interrupt commands to clear the Ready

Changed State status for each drive. This requirement can

be eliminated if drive polling is disabled via the POLL bit in

the Configure command. The Configure command must be

issued within 500 ms of the hardware or software reset for

drive polling to be disabled.

The Burst mode may be used to hold the INT pin active

during a burst, or the Non-Burst mode may be used to tog-

gle the INT pin for each byte of a burst. The Main Status

Register is always valid from the mP point of view. For ex-

ample, during a read command, after the last byte of data

has been read from the disk and placed in the FIFO, the

MSR will still indicate that the Execution Phase is active,

and that data needs to be read from the Data Register. Only

after the last byte of data has been read by the mP from the

FIFO will the Result Phase begin.

The same overrun and underrun error procedures from the

DMA mode apply to the Non-DMA mode. Also, whether

there is an error or not, an interrupt is generated at the end

of the Execution Phase, and is cleared by reading the first

Result Phase byte.

Even if drive polling is disabled, drive stepping and delayed

power down will occur in the Drive Polling Phase. The con-

troller will check the status of each drive and if necessary it

will issue a step pulse on the STEP output with the DIR

signal at the appropriate logic level. Also, the controller uses

the Drive Polling Phase to control the Automatic Low Power

mode. When the Motor Off time has expired, the controller

will wait 512 ms (based on 500 kb/s or 1 Mbs data rate)

before powering down if this function is enabled via the

Mode command.

5.3.2.5 Software Polling

If the Non-DMA Mode is selected and interrupts are not

suitable, the mP can poll the MSR during the Execution

Phase to determine when a byte is ready to be transferred.

The RQM bit (D7) in the MSR reflects the state of the INT

32

5.0 Functional Description (Continued)

TL/F/11332–5

FIGURE 5-1. PC8477B Data Separator Block Diagram

5.4 DATA SEPARATOR

disable the phase comparator when the raw data signal is

missing a clock or data pulse in the MFM or FM pattern. A

secondary PLL is used to automatically calibrate the quarter

period delay line. The secondary PLL also calibrates the

center frequency of the VCO.

The internal data separator consists of an analog PLL and

its associated circuitry. The PLL synchronizes the raw data

signal read from the disk drive. The synchronized signal is

used to separate the encoded clock and data pulses. The

data pulses are deserialized into bytes and then sent to the

mP by the controller.

To eliminate the logic associated with controlling multiple

data rates, the PC8477B supports each of the four data

rates (250, 300, 500 kb/s, and 1 Mb/s) with a separate,

optimized internal filter. The appropriate filter for each data

rate is automatically switched into the data separator circuit

when the data rate is selected via the Data Rate Select or

Configuration Control Register. These filters have been opti-

mized through lab experimentation, and are designed into

the controller to reduce the external component cost asso-

ciated with the floppy controller. The PC8477B has a dy-

namic window margin and lock range performance capable

of handling a wide range of floppy disk drives. Also, the data

separator will work well under a variety of conditions, includ-

ing the high motor speed fluctuations of floppy compatible

tape drives.

The main PLL consists of five main components, a phase

comparator, a charge pump, a filter, a voltage controlled

oscillator (VCO), and a programmable divider. The phase

comparator detects the difference between the phase of the

divider’s output and the phase of the raw data being read

from the disk. This phase difference is converted to a cur-

rent by the charge pump, which either charges or discharg-

es one of three filters which is selected based on the data

rate. The resulting voltage on the filter changes the frequen-

cy of the VCO and the divider output to reduce the phase

difference between the input data and the divider’s output.

The PLL is ‘‘locked’’ when the frequency of the divider is

exactly the same as the average frequency of the data read

from the disk. A block diagram of the data separator is

shown in Figure 5-1.

The controller takes best advantage of the internal analog

data separator by implementing a sophisticated read algo-

rithm. The ID search algorithm, shown in Figure 5-2, en-

hances the PLL’s lock characteristics by forcing the PLL to

relock to the crystal reference frequency any time the data

separator attempts to lock to a non-preamble pattern. This

algorithm ensures that the PLL is not thrown way out of lock

by write splices or bad data fields.

To ensure optimal performance, the data separator incorpo-

rates several additional circuits. The quarter period delay

line is used to determine the center of each bit cell, and to

33

5.0 Functional Description (Continued)

*The PLL will remain locked to the crystal

for 4 byte times before asserting Read Gate

TL/F/11332–6

FIGURE 5-2. Read Data AlgorithmÐState Machine

250 kb/s

300 kb/s

TL/F/11332–7

TL/F/11332–8

500 kb/s

1 Mb/s

TL/F/11332–9

TL/F/11332–10

FIGURE 5-3. PC8477B Dynamic Window Margin Performance

e

(Typical performance at V

5.0V, 25 C)

§

CC

34

5.0 Functional Description (Continued)

500 kb/s

1 Mb/s

TL/F/11332–11

TL/F/11332–12

g

FIGURE 5-4. PC8477B Dynamic Window Margin Performance with 3% ISV at 1 kHz

e

(Typical performance at V

5.0V, 25 C)

§

CC

(as they would be in a real floppy drive), and the frequency

of the data stream is subject to changes arising from motor

speed variations. Typical dynamic margin performance

curves for the PC8477B are listed in Figure 5-3. Thse mea-

surements are taken using a FlexStar FS-540 Disk Simula-

tor with a repetitive ‘‘DB6’’ data pattern. The graphs indicate

motor speed variation (MSV) vs bit jitter tolerance for the

floppy controller. For reliable performance with tape drives

the data separator needs to be able to track to instanta-

neous changes as well. Figure 5-4 shows jitter tolerance vs

MSV with an added instantaneous speed variation (ISV) of

5.5 CRYSTAL OSCILLATOR

The PC8477B is clocked by a single 24 MHz signal for the

250 kb/s, 300 kb/s, 500 kb/s, and 1 Mb/s data rates. An

on-chip oscillator is provided to enable the attachment of a

crystal or a clock signal. If a crystal is used, the following

parameters are required:

Crystal Specifications

Frequency:

Mode:

24 MHz

Parallel Resonant (preferred)

Fundamental Mode

g

3% at frequency of 1 kHz. These are typical performance

curves and measured at V

Effective Series

Resistance (ESR):

e

data separator should be able to tolerate at least 6%

5.0V, and 25 C. A good

g

§

CC

Less than 50X

Shunt Capacitance:

Less than 7 pF

MSV and 60% window margin.

5.7 PERPENDICULAR RECORDING MODE

Recommended Crystals

The PC8477B is fully compatible with perpendicular record-

ing mode disk drives at all data rates. These perpendicular

mode drives are also called 4 Mbyte (unformatted) or

NEL Frequency Controls:

NEL-C5480N

NEL-C2800N

24 MHz

SaRonix:

NMP240

24 MHz

2.88 Mbyte (formatted) drives, which refers to their maxi-

mum storage capacity. Perpendicular recording will orient

the magnetic flux changes (which represent bits) vertically

on the disk surface, allowing for a higher recording density

than the conventional longitudinal recording methods. With

this increase in recording density comes an increase in the

data rate of up to 1 Mb/s, thus doubling the storage capaci-

ty. In addition, the perpendicular 2.88M drive is read/write

compatible with 1.44M and 720k diskettes (500 kb/s and

250 kb/s respectively).

A parallel resonant crystal is preferred if at all possible. In

some cases, a series resonant crystal can be used, but care

must be taken to ensure that the crystal does not oscillate

at a sub-harmonic frequency. The oscillator circuit is able to

utilize high profile, low profile, and surface mount type crys-

tal enclosures. External bypass capacitors (5 pF to 15 pF)

should be connected from XTAL1 and XTAL2 to GND. If an

external oscillator circuit is used, it must have a duty cycle of

at least 40%–60%, and minimum input levels of 2.0V and

0.8V. The controller should be configured so that the exter-

nal oscillator clock is input into the XTAL1/CLK pin, and

XTAL2 is left unconnected.

The 2.88M drive has unique format and write data timing

requirements due to its read/write head and pre-erase head

design (see Figure 5-5). Unlike conventional disk drives

which have only a read/write head, the 2.88M drive has

both a pre-erase head and read/write head. With conven-

tional disk drives, the read/write head by itself is able to

rewrite the disk without problems. For 2.88M drives, a pre-

erase head is needed to erase the magnetic flux on the disk

surface before the read/write can write to the disk surface.

The pre-erase head is activated during disk write operations

only, i.e. Format and Write Data commands.

5.6 DYNAMIC WINDOW MARGIN PERFORMANCE

The performance of the data separator is measured by its

ability to read and decode incoming pulses shifted away

from the nominal position. The percentage window margin

indicates how much bit shift the data separator will tolerate

and still be able to read correctly. For a Dynamic Window

Margin test all the bits in the data pattern are subject to jitter

35

5.0 Functional Description (Continued)

TL/F/11332–13

FIGURE 5-5. Perpendicular Recording Drive R/W Head and Pre-Erase Head

In 2.88M drives, the pre-erase head leads the read/write

head by 200 mm, which translates to 38 bytes at 1 Mb/s

(19 bytes at 500 kb/s). For both conventional and perpen-

dicular drives, WGATE is asserted with respect to the posi-

tion of the read/write head. With conventional drives, this

means that WGATE is asserted when the read/write head is

located at the beginning of the Data Field preamble. With

the 2.88M drives, since the preamble must be pre-erased

before it is rewritten, WGATE should be asserted when the

pre-erase head is located at the beginning of the Data Field

preamble. This means that WGATE should be asserted

when the read/write head is at least 38 bytes (at 1 Mb/s)

before the preamble. See Table 4-4 for a description of the

WGATE timing for perpendicular drives at the various data

rates.

the register are used to set the data rate. The encoding of

these bits is exactly the same as those in the CCR. The

remainder of the bits in the DSR are used for other func-

tions. Consult the Register Description (Section 5.1) for

more details.

The data rate is determined by the last value that is written

to either the CCR or the DSR. In other words, either the

CCR or the DSR can override the data rate selection of the

other register.

When the data rate is selected, the microengine and data

separator clocks are scaled appropriately. Also, the

DRATE0 and DRATE1 output pins will reflect the state of

the data select bits that were last written to either the CCR

or the DSR.

5.9 WRITE PRECOMPENSATION

Because of the 38 byte spacing between the read/write

head and the pre-erase head at 1 Mb/s, the GAP2 length of

22 bytes used in the standard IBM disk format is not long

enough. There is a new format standard for 2.88M drives at

1 Mb/s called the Perpendicular Format, which increases

the GAP2 length to 41 bytes (see Figure 4-1).

Write precompensation is

a way of preconditioning the

WDATA output signal to adjust for the effects of bit shift on

the data as it is written to the disk surface. Bit shift is caused

by the magnetic interaction of data bits as they are written

to the disk surface, and has the effect of shifting these data

bits away from their nominal position in the serial MFM or

FM data pattern. Data that is subject to bit shift is much

harder to read by a data separator, and can cause soft read

errors. Write precompensation predicts where bit shift could

occur within a data pattern. It then shifts the individual data

bits early, late, or not at all such that when they are written

to the disk, the resultant shifted data bits will be back in their

nominal position.

The Perpendicular Mode command of the PC8477B will put

the floppy controller into perpendicular recording mode,

which allows it to read and write perpendicular media. Once

this command is invoked, the read, write and format com-

mands can be executed in the normal manner. The perpen-

dicular mode of the floppy controller will work at all data

rates, adjusting the format and write data parameters ac-

cordingly. See Section 4.2.8 for more details.

The PC8477B supports software programmable write pre-

compensation. Upon power up, the default write precomp

values will be used (see Table 3-5). The programmer can

choose a different value of write precomp with the DSR

register if desired (see Table 3-4). Also on power up, the

default starting track number for write precomp is track zero.

This starting track number for write precomp can be

changed with the Configure command.

5.8 DATA RATE SELECTION

The data rate can be chosen two different ways with the

PC8477B. For PC compatible software, the Configuration

Control Register at address 3F7 (hex) is used to program

the data rate for the floppy controller. The lower bits D1 and

D0 are used in the CCR to set the data rate. The other bits

should be set to zero. See Table 3-6 for the data rate select

encoding.

5.10 LOW POWER MODE LOGIC

The data rate can also be set using the Data Rate Select

Register at address 4. Again, the lower two bits of

The PC8477B supports a low power mode, in which the

oscillator and data separator circuitry are turned off. The

floppy controller will typically draw about 1 mA while in low

36

5.0 Functional Description (Continued)

power. Because the internal circuitry is driven from the oscil-

lator clock, it will also be disabled while the oscillator is off.

Upon entering the power down state, the RQM (Request

For Master) bit in the MSR will be cleared.

The Data Rate Select, Digital Output, and Configuration

Control Registers are unaffected by the power down mode.

They will remain active. It is up to the user to ensure that the

Motor and Drive Select signals are turned off.

There are two ways the part can recover from the power

down state and re-enable the oscillator and data separator.

The part will power up after a software reset via the DOR or

DSR. Since a software reset requires reinitialization of the

controller, this method can be undesirable. The part will also

power up after a read or write to either the Data Register or

Main Status Register. This is the preferred method of power

up since all internal register values are retained. It may take

a few milliseconds for the oscillator to stabilize, and the mP

will be prevented from issuing commands during this time

through the normal Main Status Register protocol. That is,

the RQM bit in the MSR will be a 0 until the oscillator has

stabilized. When the controller has completely stabilized

from power up, the RQM bit in the MSR is set to 1 and the

controller can continue where it left off.

5.11 RESET OPERATION

The PC8477B floppy controller can be reset by hardware or

software. Hardware reset is enacted by pulsing the RESET

input pin. A hardware reset will set all of the user address-

able registers and internal registers to their default values.

The Specify command values will be don’t cares, so they

must be reinitialized. The major default conditions are: FIFO

e

disabled, FIFO threshold

Drive Polling enabled.

0, Implied Seeks disabled, and

A software reset can be performed through the Digital Out-

put Register or Data Rate Select Register. The DSR reset

bit is self-clearing, while the DOR reset bit is not self-clear-

ing. If the LOCK bit in the Lock command was set to a 1

previous to the software reset, the FIFO, THRESH, and

PRETRK parameters in the Configure command will be re-

tained. In addition, the FWR, FRD, and BST parameters in

the Mode command will be retained if LOCK is set to 1. This

function eliminates the need for total reinitialization of the

controller after a software reset.

There are two modes of low power in the floppy controller:

manual low power and automatic low power. Manual low

power is enabled by writing a 1 to bit D6 of the DSR. The

chip will go into low power immediately. This bit will be

cleared to 0 after the chip is brought out of low power. Man-

ual low power can also be accessed via the Mode com-

mand. The function of the manual low power mode is a

logical OR function between the DSR low power bit and the

Mode command manual low power bit setting. When using

an external clock with the PC8477B, you must wait at least

2 ms after low power mode is invoked before turning off the

external clock. This will insure the PC8477B is powered

down correctly.

After a hardware or software reset, the Main Status Register

is immediately available for read access by the mP. It will

return a 00 hex value until all the internal registers have

been updated and the data separator is stabilized. When

the controller is ready to receive a command byte, the MSR

will return a value of 80 hex (Request for Master bit is set).

The MSR is guaranteed to return the 80 hex value within

2.5 ms after a hardware or software reset. All other user

addressable registers other than the Main Status Register

and Data Register (FIFO) can be accessed at any time,

even while the part is in reset.

Automatic low power mode will switch the controller into low

power 500 ms after it has entered the idle state (based on

the 500 kb/s MFM data rate). Once the auto low power

mode is set, it does not have to be set again, and the con-

troller will automatically go into low power mode after it has

entered the idle state. Automatic low power mode can only

be set with the Mode command. Power up from automatic

low power is performed by the method described above.

37

6.0 Device Description

Absolute Maximum Ratings

(Notes 2 and 3)

Recommended Operating

Conditions

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales

Office/Distributors for availability and specifications.

Min

Typ Max Unit

Supply Voltage (V

)

CC

4.5

5.0

5.5

a

70

V

C

Operating Temperature(T )

A

0

§

b

a

0.5V to 7.0V

Supply Voltage (V , V

)

CC CCA

ESD Tolerance

2000

V

b

Supply Differential ( V

CC

V

CCA

)

0.6V

l

e

C

R

100 pF

ZAP

b

a

Input Voltage (V )

I

0.5V to V

0.5V

CC

1.5 kX

ZAP

Output Voltage (V

)

O

CC

(Note 1)

b

a

65 C to 165 C

Storage Temperature (T

)

§

1W

STG

Power Dissipation (P )

D

a

Lead Temperature (T )

L

Soldering (10 seconds)

260 C

§

e

Capacitance T

25 C, f

§

1 MHz

A

Symbol

Parameters

Min

Typ

Max

7

Units

C

IN

C

IN1

C

IO

C

O

Input Pin Capacitance

Clock Input Capacitance

I/O Pin Capacitance

5

8

pF

10

12

8

10

6

Output Pin Capacitance

Note 1: Value based on test complying with NSC SOP5-028 human body model ESD testing using the ETS-910 tester.

Note 2: Absolute Maximum Ratings are those values beyond which damage to the device may occur.

Note 3: Unless otherwise specified all voltages are referenced to ground.

6.1 DC ELECTRICAL CHARACTERISTICS

DC Characteristics Under Recommended Operating Conditions

Symbol

Parameter

Input High Voltage

Input Low Voltage

Conditions

Min

Typ

Max

Units

V

2.0

V

CC

V

IH

b

0.5

0.8

15

IL

e

V

IL

e

I

V

Average Supply Current

0.5V, V

2.4V

CC

(Note 5)

IH

10

mA

No Loads on Outputs

e

I

V

Quiescent Supply Current

V

SS

CCSB

CCA

CCASB

IL

CC

in Low Power Mode

IL

V

CC

0.500

2.0

10

IH

No Loads on Outputs

e

I

V

Average Supply Current

V

0.5V

2.4V

CCA

(Note 5)

IL

7

5

mA

IH

No Loads on Outputs

e

V

CCA

Quiescent Supply

V

SS

IL

Current in Low Power Mode

V

CC

50

10

mA

IH

No Loads on Outputs

e

Input Leakage Current

(Note 4)

V

mA

IN

CC

b

10

IN

SS

OSCILLATOR PIN (XTAL1/CLK)

e

g

I

XTAL1 Input Current

V

IN

V

DD

or GND

400

mA

V

OSC

V

XTAL1 Input High Voltage

XTAL1 Input Low Voltage

2.0

IH

IL

V

0.8

V

b

Note 4: The MFM pin is rated for 10 mA, 150 mA because of an internal pull-up resistor.

Note 5: 500 kb/s read of ‘‘DB6’’ pattern.

38

6.0 Device Description (Continued)

DC Characteristics Under Recommended Operating Conditions (Continued)

Symbol

Parameter

Conditions

Min

Typ

Max

Units

MICROPROCESSOR INTERFACE PINS (D7–D0, A2–A0, CS, RD, WR, INT, DRQ, DACK, TC, RESET)

e b

V

Output High Voltage

Output Low Voltage

I

4 mA

3.0

V

OH

e

12 mA

0.4

10

OL

e

I

Input TRI-STATE

Leakage Current

(D7–D0, INT, DRQ)

V

0

mA

OZ

IN

CC

b

10

IN

DISK INTERFACE PINS

V

Input Hysteresis

250

mV

V

H

e b

Output High Voltage (Note 5)

Output Low Voltage

I

4 mA

3.0

OH

OL

OH

e

48 mA

0.4

10

V

OL

e

I

Output High Leakage Current

(Note 6)

V

CC

0V

,

mA

LKG

IN

b

10

IN

MISCELLANEOUS PINS

e b

V

OH

V

OL

V

OL

Output High Voltage

(DRATE0–1, MFM)

I

4 mA

OH

OL

3.0

V

e

Output Low Voltage

(DRATE0–1)

6 mA

0.4

V

e

Output Low Voltage (MFM)

4 mA

Note 5: V

for the disk interface pins is valid for CMOS buffered outputs only.

OH

Note 6: This parameter is valid for Open Drain output configuration only.

6.2 PHASE LOCKED LOOP CHARACTERISTICS

Parameter

Symbol

Conditions

(Note)

Min

Typ

73

Max

Units

Dynamic Window Margin

T

DW

68

%

Note: Dynamic window margin is tested at both V extremes with a repeating ‘‘DB6’’ pattern and 0% MSV. 500 kb/s, 300 kb/s, 250 kb/s and 1 Mb/s are tested

CC

at 68%.

39

6.0 Device Description (Continued)

6.2 AC ELECTRICAL CHARACTERISTICS

e

a

0 C to 70 C, V

e

5.0V 10%

CC

g

6.2.1. AC Test Conditions T

§

A

Load Circuit

AC Testing Input,

Output Waveform

TL/F/11332–15

TL/F/11332–14

6.2.2 Clock Timing

Symbol

Parameter

Min

16

Max

Units

ns

t

Clock High Pulse Width

Clock Low Pulse Width

Clock Period

CH

16

ns

CL

40

43

ns

CP24

ICP

Internal Clock Period (Table 6-1)

Data Rate Period (Table 6-1)

DRP

TABLE 6-1. Nominal t , t

ICP DRP

Values

MFM Data Rate

t

Value

Units

DRP

ICP

1 Mb/s

500 kb/s

300 kb/s

250 kb/s

1000

2000

3333

4000

3 x t

5 x t

6 x t

125

208

250

ns

CP

TL/F/11332–16

FIGURE 6-1. Clock Timing

40

6.0 Device Description (Continued)

6.2.3 Microprocessor Read Timing

Symbol

Parameter

Min

5

Max

Units

ns

t

Address Setup to Read Active

Read Active Pulse Width

AR

RR

RA

RD

RH

DF

RI

60

0

ns

Address Hold from Read Inactive

Data Valid from Read Active

Read Inactive Pulse Width

ns

45

ns

45

5

ns

Data Output Float Delay

25

55

ns

Interrupt Delay from Read Inactive

Data Output Hold from Read Inactive

ns

DH

TL/F/11332–17

FIGURE 6-2. Microprocessor Read Timing

41

6.0 Device Description (Continued)

6.2.4 Microprocessor Write Timing

Symbol

Parameter

Min

5

Max

Units

ns

t

Address Setup to Write Active

Write Active Pulse Width

AW

WW

WA

WH

ADW

DW

WD

WI

60

0

ns

Address Hold from Write Inactive

Write Inactive Pulse Width

ns

45

65

30

0

ns

Address Setup to Write Inactive

Data Setup to Write Inactive

Data Hold from Write Inactive

Interrupt Delay from Write Inactive

ns

55

ns

TL/F/11332–18

FIGURE 6-3. Microprocessor Write Timing

42

6.0 Device Description (Continued)

6.2.5 DMA Timing

Symbol

Parameter

Min

8 x t

Max

Units

ms

ns

t

DRQ Period (Except Non-Burst DMA) (Note 8)

DRQ Inactive Non-Burst Pulse Width

DACK Active Edge to DRQ Inactive

RD, WR Active Edge to DRQ Inactive (Note 7)

DRQ to RD, WR Active

QP

QQ

KQ

RQ

QR

TT

DRP

300

400

65

ns

65

ns

15

50

ns

TC Active Pulse Width

ns

TC Active Edge to DRQ Inactive (Note 9)

DACK Active Pulse Width

75

ns

TQ

KK

KI

65

25

5

ns

DACK Inactive Pulse Width

ns

DACK Setup to RD, WR Active

DACK Hold from RD, WR Inactive

ns

KR

RK

QW

0

ns

DRQ to End of RD, WR (Note 8)

(DRQ Service Time)

(8 x t

DRP

ms

b

16 x t

)

ICP

t

QT

DRQ to TC Active (Note 8)

(DRQ Service Time)

(8 x t

DRP

b

16 x t

ICP

Note 7: The active edge of RD or WR is recognized only when DACK is active.

e

Note 8: Values shown are with the FIFO disabled, or with FIFO enabled and THRESH

0. For nonzero values of THRESH, add (THRESH x 8 x t

) to the values

DRP

shown.

Note 9: During normal DMA operation TC should occur when DACK is active during the last byte of the last sector transferred.

TL/F/11332–19

FIGURE 6-4. DMA Timing

43

6.0 Device Description (Continued)

6.2.6 Reset Timing

Symbol

Parameter

Min

Max

Units

ns

t

Reset Width (Note 10)

Reset to Control Inactive

100

RW

300

ns

RC

Note 10: The software reset pulse width is 100 ns. The hardware reset pulse width with an external 10 kX pull-up or pull-down resistor on the MFM pin is 100 ns.

When using the internal pull-up resistor on the MFM pin, the hardware reset pulse width is 170 ns (assumes no load on MFM).

TL/F/11332–20

FIGURE 6-5. Reset Timing

6.2.7 Write Data Timing

Symbol

Parameter

Min

Table 6-2

100

Max

Units

ns

t

Write Data Pulse Width

WDW

HDS

HDH

HDSEL Setup to WGATE Active

HDSEL Hold from WGATE Inactive

ms

750

ms

TABLE 6-2. Minimum t

WDW

Values

Data Rate

1 Mb/s

t

Value

Units

DRP

WDW

1000

2000

3333

4000

2 x t

250

ns

ICP

500 kb/s

300 kb/s

250 kb/s

250

375

500

TL/F/11332–21

FIGURE 6-6. Write Data Timing

44

6.0 Device Description (Continued)

6.2.8 Drive Control Timing

Symbol

Parameter

DR0–DR3, MTR0–MTR3 from End of WR

DIR Setup to STEP Active

Min

Max

Units

ns

t

100

DRV

DST

STD

STP

SRT

IW

6

ms

DIR Hold from STEP Inactive

STEP Active High Pulse Width

STEP Rate Time (see Table 4-13)

Index Pulse Width

t

ms

SRT

8

1

ms

ns

100

TL/F/11332–22

FIGURE 6-7. Drive Control Timing

6.2.9 Read Data Timing

Symbol

Parameter

Min

Max

Units

t

Read Data Pulse Width

50

ns

RDW

TL/F/11332–23

FIGURE 6-8. Read Data Timing

45

7.0 Reference Section

7.1 MNEMONIC DEFINITIONS FOR PC8477B COMMANDS

Symbol

Description

Symbol

Description

BFR

Buffer enable bit used in the Mode command.

Enabled open-collector output buffers.

MFM

Modified Frequency Modulation control bit used

in the Read, Write, Format, Scan and Verify

commands. Selects MFM or FM data encoding.

BST

Burst Mode disable control bit used in Mode

command. Selects the Non-Burst FIFO mode if

the FIFO is enabled.

MFT

MNT

MT

Motor Off Time programmed in the Specify

command.

DC0

DC1

DC2

DC3

Drive Configuration 0–3. Used to set a drive to

conventional or perpendicular mode. Used in

Perpendicular Mode command.

Motor On Time programmed in the Specify

command.

Multi-Track enable bit used in the Read, Write,

Scan and Verify commands.

DENSEL Density Select control bits used in the Mode

command.

OW

Overwrite control bit used in the Perpendicular

Mode command.

DIR

DMA

DR0

DTL

EC

Direction control bit used in Relative Seek

command to indicate step in or out.

POLL

Enable Drive Polling bit used in the Configure

command.

DMA mode enable bit used in the Specify

command.

PRETRK Precompensation Track Number used in the

Configure command.

Drive Select 0–1 bits used in most commands.

Selects the logical drive.

PTR

Present Track Register. Contains the internal

track number for one of the four logical disk

drives.

Data Length parameter used in the Read, Write,

Scan and Verify commands.

PU

Pump diagnostic enable bit used in the Mode

command.

Enable Count control bit used in the Verify

command. When this bit is 1, the DTL parameter

becomes SC (Sector Count).

R255

RG

Recalibrate control bit used in Mode command.

Sets maximum recalibrate step pulses to 255.

EIS

Enable Implied Seeks. Used in the Configure

command.

Read Gate diagnostic enable bit used in the

Mode command.

EOT

ETR

FIFO

End of Track parameter set in the Read, Write,

Scan, and Verify commands.

RTN

SC

Relative Track Number used in the Relative

Seek command.

Extended Track Range used with the Seek

command.

Sector Count control bit used in the Verify

command.

First-In First-Out buffer. Also a control bit used in

the Configure command to enable or disable the

FIFO.

SK

Skip control bit used in read and scan

operations.

SRT

Step Rate Time programmed in the Specify

command. Determines the time between step

pulses for seek and recalibrates.

FRD

FWR

GAP

HD

FIFO Read disable control bit used in the Mode

command.

FIFO Write disable control bit used in the Mode

command.

ST0

ST1

ST2

ST3

Status Register 0–3. Contains status

information about the execution of a command.

Read in the Result Phase of some commands.

Gap2 control bit used in the Perpendicular Mode

command.

Head Select control bit used in most commands.

Selects Head 0 or 1 of the disk.

THRESH FIFO threshold parameter used in the Configure

command.

IAF

Index Address Field control bit used in the Mode

command. Enables the ISO Format during the

Format command.

TMR

Timer control bit used in the Mode command.

Affects the timers set in the Specify command.

WG

Write Gate control bit used in the Perpendicular

Mode command.

IPS

Implied Seek enable bit used in the Mode, Read,

Write, and Scan commands.

WLD

Wildcard bit in the Mode command used to

enable or disable the wildcard byte (FF) during

Scan commands.

LOCK

Lock enable bit in the Lock command. Used to

make certain parameters unaffected by a

software reset.

LOW

PWR

Low Power control bits used in the Mode

command.

46

7.0 Reference Section (Continued)

7.2 PC8477B ENHANCEMENTS VS 82077AA

PC8477B data separator is designed to work with the strict-

est motor speed and bit jitter requirements of both floppy

and tape drives.

The enhancements listed below are additional functions of

the PC8477B that the 82077AA does not have, and do not

affect the compatibility between the two floppy controllers.

Low Power Mode

Commands

The typical measured low power current for the PC8477B

(analog and digital) is 1 mA. The typical measured low pow-

er current for the 82077AA is 2 mA–3 mA.

The following are PC8477B commands not supported by

the 82077AA.

The PC8477A supports the 82077AA manual low power

mode by writing to the Low Power bit (D6) in the Data Rate

Select register. The low power mode is turned off by issuing

a reset to the chip, whereupon re-initialization is necessary.

In addition, the PC8477B supports a manual low power AND

automatic low power mode via the Mode command. Manual

low power must be invoked every time the low power mode

is desired. Automatic low power mode need only be invoked

once during initialization, and then low power is entered

whenever the floppy controller is idle.

Mode CommandÐControls several enhanced fea-

tures of the PC8477B such as: Implied Seeks, Low

Power mode, additional FIFO modes, and DENSEL

encoding. The Mode command parameters are de-

fault to 82077AA compatible states, and will be un-

affected by 82077AA-based software that does not

recognize the existence of a Mode command. See

the PC8477B data sheet for more details.

NSC CommandÐThis one byte command is used

to identify the PC8477B in the system. Other floppy

controllers will return an 80 hex (invalid command),

while the PC8477B will return a value of 73 hex (the

lower four bits are reserved to indicate revision up-

dates in the part).

As mentioned, the 82077AA and PC8477B will exit the low

power mode after a reset. The PC8477B will also exit the

low power mode after any read or write to the Main Status

Register or Data Register. In this way, the part can exit low

power cleanly without requiring additional software initializa-

tion. This feature gives the PC8477B an advantage in that

once software has initialized it for automatic low power, no

additional software modifications are necessary, and the

chip will power down whenever it is idle. Even for manual

low power mode via the DSR or Mode command, the

PC8477B can return to normal mode without re-initialization,

as required for the 82077.

Set Track CommandÐThis command allows the

user to program the value of any of the four Present

Track Registers corresponding to the four logical

drives.

FIFO Operation

The PC8477B FIFO is compatible with the 82077AA FIFO,

with the addition of a Non-Burst mode. The default setting

when the FIFO is enabled is the 82077AA compatible Burst

mode. The Non-Burst mode is enabled via the Mode com-

mand. The Non-Burst mode will pulse the DRQ or INT sig-

nals during a burst transfer to or from the FIFO.

Reset Pulse Width

The PC8477B software reset pulse width is 100 ns mini-

mum. This means that software can issue two consecutive

writes to the Digital Output Register of the PC8477B to tog-

gle the Reset Controller bit (D2) without intervening delay.

This specification is significantly better than the 82077AA

minimum software reset pulse width, which is specified as

3.5 ms (worst case at the 250 kb/s data rate).

For both the Burst and Non-Burst modes with the FIFO en-

abled, no external circuitry is required with the PC8477B

during DMA verify transfers. During verify operations, the

DMA controller will assert the DACK signal without a RD

signal in response to a DRQ from the floppy controller. The

82077AA, however, requires external circuitry to create the

RD signal during DMA verify operations with its FIFO en-

abled in order to work successfully without an overrun error.

The published Intel bug fix for the 82077AA can only be

used for motherboard applications and not for add-in

boards. The PC8477B does not have this problem.

When using an external pull-up or pull-down 10 kX resistor

on the MFM pin, the hardware reset pulse width is also

100 ns minimum for the PC8477B. The minimum hardware

reset pulse width for the 82077AA is 7.1 ms. Again, the

PC8477B specification is much better, allowing the system

reset pulse to be very short.

Tape Drive Register

Also, because of the byte counter in the PC8477B design,

the DRQ or INT signal will be deasserted when the last byte

of a sector is written to the FIFO during the execution phase

of a write or format operation. The 82077AA does not deas-

sert DRQ or INT until the last byte has been read out of the

FIFO. This will cause a delay in the deassertion of DRQ or

INT of up to 16 byte times, resulting in extra bytes trans-

ferred to the floppy controller. The PC8477B does not have

this problem.

The PC8477B will support reads and writes to this register,

just as the 82077AA does. However, the PC8477B will not

use the information written to the Tape Drive Register to

alter the state of the Data Separator. That is, there is only

one mode of the internal PC8477B data separator, a high

performance mode that will support the requirements for all

floppy and tape drives.

Implied Seeks

Data Separator

The PC8477B supports our popular DP8473 method as well

as the 82077AA method of implementing Implied Seeks.

The DP8473 method is to set a bit in the Mode command

for enabling Implied Seeks, and then set the Implied Seek

bit if desired in the Read, Write, or Scan commands. The

82077AA method is to set the EIS bit (enable implied seeks)

in the Configure command, and then Implied Seeks will al-

ways be enabled for Read, Write, and Verify commands.

The PC8477B data separator’s performance meets that of

the 82077AA’s. However, there are no dual modes in the

PC8477B data separator whereas the 82077AA data sepa-

rator has an internal floppy drive mode and an internal tape

drive mode. This singular mode design of the PC8477B data

separator eliminates the need for hardware or software con-

trol and provides for more consistent performance. The

47

7.0 Reference Section (Continued)

TABLE 7-1 8477B–82077 Parameter Comparison

Description

Absolute Maximum Ratings

PC8477B 82077AA

82077SL

Units

b

0.5–8.0

Supply Voltage

0.5–7.0

0.5–8.0

V

DC Limits

V

Clock MIN

2.0

4.0

3.9

2.5

3.9

2.5

V

IH

OL

OH

CC

e

I

MFM pin (V

0.4V)

3.0V)

mA

OL

e

MFM pin (V

OH

Low Power (Analog

b

2.5

4.0

2.5

a

Digital) Typical

Digital) Tested

0.505

2.05

1.5

Ð

a

Low Power (Analog

CC

no spec

Ð

AC Timings

t

(t )–INTERNAL Clock Period

ICP

5

1 Mb/s

125

208

250

60

125

250

420

500

90

125

250

420

500

90

ns

500 kb/s

300 kb/s

250 kb/s

t

(t )–Read Active Pulse Width MIN

RR

8

(t )–Read to Valid Data

10 RD

45

80

(t )–Read Inactive Pulse Width

11 RH

45

60

(t )–Delay to Float

12 DF

25

35

(t )–Interrupt Delay from Read Inactive MAX

13 RI

1 Mb/s

55

60

30

45

65

250

375

545

625

90

250

375

545

625

90

ns

500 kb/s

300 kb/s

250 kb/s

t

(t )–Write Active Pulse Width MIN

16 WW

(t )–Data Setup to Write Active

19 DW

70

(t )–Write Inactive Pulse Width

18 WH

60

–Address Setup to Write Inactive MIN

ADW

(t )–Interrupt Delay from Write Inactive

no spec

21 WI

1 Mb/s

55

8

250

375

545

625

6.5

250

375

545

625

6.5

ns

ms

ns

500 kb/s

300 kb/s

250 kb/s

t

(t )–DRQ Cycle Period MIN

22 QP

(t )–DACK Active to DRQ Inactive MAX

23 KQ

65

75

a

(t

23a QK

t )–DRQ to DACK Inactive

KK

1 Mb/s

60

no spec

100

83

166

ns

500 kb/s

300 kb/s

250 kb/s

60

280

60

333

t

(t )–RD, WR Active to DRQ Inactive MAX

24 RQ

65

100

(t )–DRQ to RD, WR Active MIN

27 QR

15

0

(t )–TC Active to DRQ Inactive MAX

29 TQ

75

150

–DACK Active Pulse Width MIN

65

no spec

7083

no spec

7083

500

KK

–DACK Inactive Pulse Width MIN

25

KI

–DRQ to DACK Active MIN

10

QK

(t )–Reset Pulse Width MIN

30 RW

100

160

(t )–Software Reset Pulse Width MIN (Worst Case)

30a RW

3500

(t )–Reset to Control Inactive

31 RC

2000

(t )–Write Data Pulse Width MIN

32 WDW

1 Mb/s

250

416

500

150

360

615

740

150

360

615

740

ns

500 kb/s

300 kb/s

250 kb/s

48

7.0 Reference Section (Continued)

TABLE 7-1 8477B–82077AA Parameter Comparison (Continued)

Description

AC Timings (Continued)

PC8477B

82077AA

82077SL

Units

t

(t

)–DIR Setup to STEP Active MIN

)–DIR Hold from STEP Inactive MIN

)–STEP Active Pulse Width

6

4

ms

35 DST

(t

36 STD

t

10

2.5

10

2.5

SRT

8

(t

37 STP

(t )–Index Pulse Widh MIN

39 IW

1 Mb/s

100

625

ns

500 kb/s

300 kb/s

250 kb/s

1250

2100

2500

1250

2100

2500

t (t )–HDSEL Hold from WGATE Inactive MIN

41 HDH

1 Mb/s

*750

*100

716

1432

716

1432

ms

500 kb/s

300 kb/s

250 kb/s

2719

2864

t

–HDSEL Setup to WGATE Active

no spec

HDS

*These timings are required to support perpendicular recording drives.

49

7.0 Reference Section (Continued)

7.3 PC8477B INTERFACE IN A PC-AT

The PC8477B interface to the PC-AT bus is simple and re-

quires only an external address decoder. All the microproc-

essor inputs and outputs of the PC8477B can be connected

directly to the peripheral bus due to the 12 mA sink capabili-

ty. Figure 7-1 shows the interface with the floppy drive

header, and the signal connections to the AT bus. The de-

sign will support 1.2 Meg, 1.44 Meg, and 2.88 Meg drives.

Support for the 2.88 Meg perpendicular drives is accom-

plished with the additional density encoding signal

(DRATE0) on floppy header pin 6. This interface solution will

support perpendicular drives with the encoding scheme list-

ed in Table 7-2 below.

The HD signal is floppy header pin 2, and the ED signal is

header pin 6. This standard scheme is supported by a num-

ber of perpendicular drive manufacturers. Some new per-

pendicular drives are using an auto media sense for density

selection. These drives will not require either the HD or ED

signals. Here the data rate is determined optically by the

drive due to the hole in the disk.

The only use of the 16L8 PAL is address decoding for the

proper floppy address range. The primary range is 3F0–3F7

while the secondary address range is 370–377. Selection

between can be accomplished with a jumper if needed. The

address lines A9–A3 and AEN are input to the PAL from the

peripheral bus. The following equation can be used for the

primary range.

TABLE 7-2. Density Encoding

Media

1 Meg

2 Meg

4 Meg

Data Rate

250 kb/s

500 kb/s

1 Mb/s

HD

0

ED

0

e

CS

!(!AEN * A9 * A8 * A7 * A6 * A5 * A4 * !A3)

In this design we have used 1 kX pull-up resistors on the

floppy drive interface. If the intended design is to be used

with external drives or long cabling, or if 5.25 disk drives

1

0

×

X

1

are to be supported, 150 kX pull-ups should be considered.

TL/F/11332–24

FIGURE 7-1. 8477B in PC-AT System

50

7.0 Reference Section (Continued)

7.4 SOFTWARE INITIALIZATION SEQUENCE

Following power up the system will issue a hardware reset

to the PC8477B. This will put the internal registers and cir-

cuitry into a known state after which the software initializa-

tion sequence can begin.

End ResetÐThe first task is to bring the PC8477B out of

the reset state by writing 0CH to the DOR register. The

software should then poll the MSR until 80H is returned. At

this point the controller is ready to begin processing com-

mands.

Service Ready Changed State InterruptÐOnce an inter-

rupt is received the software should issue 4 SENSE INTER-

RUPT commands for each of the 4 logical drives. This is

due to the fact that after a reset, drive polling is enabled by

default.

Set Data RateÐThe data rate should be set via a write to

the CCR register. The default state is 250 kb/s following

reset.

Configure the FIFOÐThe default setting is with the FIFO

disabled. If the perpendicular format is to be supported the

FIFO will need to be enabled due to the higher data rates

used. The FIFO threshold level should be set based on the

DMA response time of the system.

A lower value of

THRESH corresponds to a fast system with a quick DMA

response time, whereas a higher value of THRESH corre-

sponds to a sluggish system with slower DMA response

time. A write to the configuration register is also used to

enable implied seeks if that feature is desired.

LockÐThis command will lock the FIFO parameters which

will leave them unaffected following a reset. Set the LOCK

bit to 1 to lock the parameters.

TL/F/11332–25

Specify CommandÐAfter a reset a specify command must

always be issued in the initialization sequence. This is be-

cause there is no default for these values. With this com-

mand you will set up the motor on and motor off times as

well as the step rate times. DMA mode is also enabled via

this command.

FIGURE 7-2. PC8477B Initialization

7.5 PC8477A/PC8477B DIFFERENCES

There are two differences to note between the 8477A and

8477B versions. The NSC command result phase returns a

73H in the 8477B, and returns a 72H in the 8477A. This

command is used strictly to distinguish new revisions of the

part. The second difference pertains to the Motor On Time

(MNT) values when the FDC is in Mode 1. The new table is

listed in Table 4-15 of this document. The MNT values at

500 kb/s for Mode 1 were changed to be the same as the

1 Mb/s values. The changes to the MNT values should not

affect application software.

Mode CommandÐThere are several advanced features

that can be enabled via the mode command. Head settling

time for implied seeks, open collector drive interface out-

puts, ISO format pattern, low power modes, enabling 255

step pulses for higher density media, and FIFO burst mode

are just some of the features.

Recalibrate DriveÐFirst access to the drive should be to

RECALIBRATE to track 0. Following the recalibrate com-

mand it is necessary to issue a SENSE INTERRUPT com-

mand to determine if the recalibrate was successful. If no

track 0 was detected, an error will be reported. This is a

common method to determine if a drive is connected.

7.6 REVISION HISTORY

Nov. 1990 Preliminary PC8477 datasheet

May 1992 Preliminary PC8477B datasheet

ÐAdd new part markings

ÐAdd PQFP package option

Seek/Read/Write/FormatÐAt this point the initialization

is complete and normal disk I/O operations would start to

occur. In normal operations it would not be necessary to re-

initialize prior to each access. Normal disk I/O operations

would include writes to CCR register to change data rates,

recalibrating to track 0, toggling the motor and drive selects

through the DOR register, seeking to the appropriate track,

and initializing the DMA controller prior to Read/Write/For-

mat commands.

ÐAdd 1.25 Mb/s data rate support

ÐAdd Dynamic Window Margin spec.

ÐImprove ICC and AC databus timings

ÐAdd applications reference section

June 1993 Final PC8477B datasheet

ÐElimination of 1.25 Mb/s data rate support

ÐElimination of FM mode functional testing

ÐESD tolerance spec. raised to 2000V

ÐReplace t

ÐChange t

spec. with t

and t

KR RK

spec. from 160 ns to 300 ns

QK

Figure 7-2 shows a block diagram representing the initializa-

tion sequence for the PC8477B.

RC

@

300 Kb/s from 416 ns to 375 ns

WDW

51

52

Physical Dimensions inches (millimeters)

Plastic Chip Carrier (V)

Order Number PC8477BV-1

NS Package Number VA68A

53

Physical Dimensions inches (millimeters) (Continued)

Plastic Quad Flat Package (PQFP)

Order Number PC8477BVF-1

NS Package Number VF60A

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT

DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL

SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or

systems which, (a) are intended for surgical implant

into the body, or (b) support or sustain life, and whose

failure to perform, when properly used in accordance

with instructions for use provided in the labeling, can

be reasonably expected to result in a significant injury

to the user.

2. A critical component is any component of a life

support device or system whose failure to perform can

be reasonably expected to cause the failure of the life

support device or system, or to affect its safety or

effectiveness.

National Semiconductor

Corporation

2900 Semiconductor Drive

P.O. Box 58090

Santa Clara, CA 95052-8090

Tel: 1(800) 272-9959

TWX: (910) 339-9240

National Semiconductor

GmbH

Livry-Gargan-Str. 10

D-82256 Furstenfeldbruck

Germany

Tel: (81-41) 35-0

Telex: 527649

Fax: (81-41) 35-1

National Semiconductor National Semiconductor

National Semiconductores

Do Brazil Ltda.

Rue Deputado Lacorda Franco

120-3A

Sao Paulo-SP

Brazil 05418-000

Tel: (55-11) 212-5066

Telex: 391-1131931 NSBR BR

Fax: (55-11) 212-1181

National Semiconductor

(Australia) Pty, Ltd.

Building 16

Business Park Drive

Monash Business Park

Nottinghill, Melbourne

Victoria 3168 Australia

Tel: (3) 558-9999

Japan Ltd.

Hong Kong Ltd.

Sumitomo Chemical

Engineering Center

Bldg. 7F

13th Floor, Straight Block,

Ocean Centre, 5 Canton Rd.

Tsimshatsui, Kowloon

1-7-1, Nakase, Mihama-Ku Hong Kong

Chiba-City,

Tel: (852) 2737-1600

Fax: (852) 2736-9960

Ciba Prefecture 261

Tel: (043) 299-2300

Fax: (043) 299-2500

Fax: (3) 558-9998

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.


型号：	PC8477B
厂家：	National Semiconductor
描述：	Advanced Floppy Disk Controller 高级软盘控制器控制器
文件：	总54页 (文件大小：576K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

PC8477B [NSC]

相关型号：

PC8477BV

PC8477BV-1

PC8477BV-30

PC8477BVF

PC8477BVF-1

PC8477V

PC847AB

PC847AC

PC847AD

PC847BC

PC847BD

PC847CD