SM72501MF [NSC]
SolarMagic Precision, CMOS Input, RRIO, Wide Supply Range Amplifier; 的SolarMagic精密, CMOS输入, RRIO ,宽电源范围放大器![SM72501MF](http://pdffile.icpdf.com/pdf1/p00170/img/icpdf/SM725_952616_icpdf.jpg)
型号: | SM72501MF |
厂家: | ![]() |
描述: | SolarMagic Precision, CMOS Input, RRIO, Wide Supply Range Amplifier |
文件: | 总20页 (文件大小:1513K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
May 10, 2011
SM72501
SolarMagic Precision, CMOS Input, RRIO, Wide Supply
Range Amplifier
General Description
Features
The SM72501 is a low offset voltage, rail-to-rail input and out-
put precision amplifier with a CMOS input stage and a wide
supply voltage range. The SM72501 is ideal for sensor inter-
face and other instrumentation applications.
Renewable Energy Grade
■
Unless otherwise noted, typical values at VS = 5V
Input offset voltage
Input bias current
Input voltage noise
CMRR
±200 µV (max)
■
■
■
■
■
■
■
■
■
■
±200 fA
9 nV/√Hz
130 dB
The guaranteed low offset voltage of less than ±200 µV along
with the guaranteed low input bias current of less than ±1 pA
makes the SM72501 ideal for precision applications. The
SM72501 is built utilizing VIP50 technology, which allows the
combination of a CMOS input stage and a 12V common mode
and supply voltage range. This makes the SM72501 a great
choice in many applications where conventional CMOS parts
cannot operate under the desired voltage conditions.
Open loop gain
130 dB
−40°C to 125°C
2.5 MHz
Temperature range
Unity gain bandwidth
Supply current (SM72501)
Supply voltage range
Rail-to-rail input and output
715 µA
2.7V to 12V
The SM72501 has a rail-to-rail input stage that significantly
reduces the CMRR glitch commonly associated with rail-to-
rail input amplifiers. This is achieved by trimming both sides
of the complimentary input stage, thereby reducing the differ-
ence between the NMOS and PMOS offsets. The output of
the SM72501 swings within 40 mV of either rail to maximize
the signal dynamic range in applications requiring low supply
voltage.
Applications
High impedance sensor interface
■
■
■
■
■
■
Battery powered instrumentation
High gain amplifiers
DAC buffer
The SM72501 is offered in the space saving 5-Pin SOT23.
This small package is an ideal solution for area constrained
PC boards and portable electronics.
Instrumentation amplifier
Active filters
Typical Application
30142105
Precision Current Source
© 2011 National Semiconductor Corporation
301421
www.national.com
Storage Temperature Range
Junction Temperature (Note 3)
Soldering Information
−65°C to +150°C
+150°C
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ꢀInfrared or Convection (20 sec)
235°C
260°C
ꢀWave Soldering Lead Temp. (10
ESD Tolerance (Note 2)
sec)
ꢀHuman Body Model
2000V
ꢀMachine Model
200V
1000V
Operating Ratings (Note 1)
Charge-Device Model
Temperature Range (Note 3)
−40°C to +125°C
2.7V to 12V
VIN Differential
±300 mV
Supply Voltage (VS = V+ – V−)
Supply Voltage (VS = V+ – V−)
Voltage at Input/Output Pins
Input Current
13.2V
V++ 0.3V, V− − 0.3V
Package Thermal Resistance (θJA (Note 3))
5-Pin SOT23
265°C/W
10 mA
3V Electrical Characteristics (Note 4)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 3V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Min
Typ
Max
Symbol
VOS
Parameter
Input Offset Voltage
Conditions
Units
μV
(Note 6) (Note 5) (Note 6)
±37
±1
±200
±500
TCVOS
IB
Input Offset Voltage Temperature (Note 7)
Drift
±5
μV/°C
Input Bias Current
(Note 7, Note 8)
−40°C ≤ TA ≤ 85°C
±0.2
±1
±50
pA
(Note 7, Note 8)
±0.2
±1
±400
−40°C ≤ TA ≤ 125°C
IOS
Input Offset Current
40
fA
CMRR
Common Mode Rejection Ratio
86
80
130
0V ≤ VCM ≤ 3V
dB
2.7V ≤ V+ ≤ 12V, Vo = V+/2
PSRR
CMVR
Power Supply Rejection Ratio
Common Mode Voltage Range
86
82
98
dB
V
–0.2
–0.2
3.2
3.2
CMRR ≥ 80 dB
CMRR ≥ 77 dB
AVOL
Open Loop Voltage Gain
100
96
114
124
RL = 2 kΩ
VO = 0.3V to 2.7V
dB
100
96
RL = 10 kΩ
VO = 0.2V to 2.8V
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
VOUT
Output Voltage Swing High
Output Voltage Swing Low
40
30
40
20
42
80
120
mV
from V+
40
60
60
80
mV
mA
40
50
IOUT
Output Current
(Note 3, Note 9)
Sourcing VO = V+/2
VIN = 100 mV
25
15
Sinking VO = V+/2
VIN = −100 mV
25
20
42
IS
Supply Current
0.670
0.9
1.0
1.2
mA
SR
Slew Rate (Note 10)
AV = +1, VO = 2 VPP
10% to 90%
V/μs
www.national.com
2
Min
Typ
Max
Symbol
Parameter
Gain Bandwidth
Conditions
Units
(Note 6) (Note 5) (Note 6)
GBW
2.5
MHz
%
THD+N
Total Harmonic Distortion + Noise
0.02
f = 1 kHz, AV = 1, R.L = 10 kΩ
en
Input Referred Voltage Noise
Density
f = 1 kHz
9
nV/
in
Input Referred Current Noise
Density
f = 100 kHz
1
fA/
5V Electrical Characteristics (Note 4)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2, and RL > 10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Min
Typ
Max
Symbol
Parameter
Input Offset Voltage
Conditions
Units
(Note 6) (Note 5) (Note 6)
VOS
±37
±200
±500
μV
TCVOS
IB
Input Offset Voltage Temperature Drift
Input Bias Current
(Note 7)
±1
±5
μV/°C
(Note 7, Note 8)
±0.2
±1
±50
−40°C ≤ TA ≤ 85°C
(Note 7, Note 8)
pA
±0.2
±1
±400
−40°C ≤ TA ≤ 125°C
IOS
Input Offset Current
40
fA
CMRR
Common Mode Rejection Ratio
88
83
130
0V ≤ VCM ≤ 5V
dB
2.7V ≤ V+ ≤ 12V, VO = V+/2
PSRR
CMVR
Power Supply Rejection Ratio
Common Mode Voltage Range
86
82
100
dB
V
–0.2
–0.2
5.2
5.2
CMRR ≥ 80 dB
CMRR ≥ 78 dB
AVOL
Open Loop Voltage Gain
100
96
119
130
RL = 2 kΩ
VO = 0.3V to 4.7V
dB
100
96
RL = 10 kΩ
VO = 0.2V to 4.8V
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
RL = 2 kΩ to V+/2
RL = 10 kΩ to V+/2
VOUT
Output Voltage Swing High
Output Voltage Swing Low
60
40
50
30
66
110
130
mV
from V+
50
70
80
90
mV
mA
40
50
IOUT
Output Current
(Note 3, Note 9)
Sourcing VO = V+/2
VIN = 100 mV
40
28
Sinking VO = V+/2
VIN = −100 mV
40
28
76
IS
Supply Current
0.715
1.0
1.0
1.2
mA
SR
Slew Rate (Note 10)
AV = +1, VO = 4 VPP
10% to 90%
V/μs
GBW
Gain Bandwidth
2.5
MHz
%
THD+N
Total Harmonic Distortion + Noise
0.02
f = 1 kHz, AV = 1, RL = 10 kΩ
3
www.national.com
Min
Typ
Max
Symbol
Parameter
Conditions
Units
(Note 6) (Note 5) (Note 6)
en
in
Input Referred Voltage Noise Density
Input Referred Current Noise Density
f = 1 kHz
9
nV/
fA/
f = 100 kHz
1
±5V Electrical Characteristics (Note 4)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5V, V− = −5V, VCM = 0V, and RL > 10 kΩ to 0V. Bold-
face limits apply at the temperature extremes.
Min
Typ
Max
Symbol
Parameter
Input Offset Voltage
Conditions
Units
(Note 6) (Note 5) (Note 6)
VOS
±37
±200
±500
μV
TCVOS
IB
Input Offset Voltage Temperature Drift
Input Bias Current
(Note 7)
±1
±5
μV/°C
(Note 7, Note 8)
±0.2
1
±50
−40°C ≤ TA ≤ 85°C
(Note 7, Note 8)
pA
±0.2
1
±400
−40°C ≤ TA ≤ 125°C
IOS
Input Offset Current
40
fA
CMRR
Common Mode Rejection Ratio
92
88
138
−5V ≤ VCM ≤ 5V
dB
2.7V ≤ V+ ≤ 12V, VO = 0V
PSRR
CMVR
Power Supply Rejection Ratio
Common Mode Voltage Range
86
82
98
dB
V
−5.2
−5.2
5.2
5.2
CMRR ≥ 80 dB
CMRR ≥ 78 dB
AVOL
Open Loop Voltage Gain
100
98
121
134
RL = 2 kΩ
VO = −4.7V to 4.7V
dB
100
98
RL = 10 kΩ
VO = −4.8V to 4.8V
VOUT
Output Voltage Swing High
Output Voltage Swing Low
90
40
90
40
86
150
170
RL = 2 kΩ to 0V
RL = 10 kΩ to 0V
RL = 2 kΩ to 0V
RL = 10 kΩ to 0V
mV
from V+
80
100
130
150
mV
from V–
50
60
IOUT
Output Current
(Note 3, Note 9)
Sourcing VO = 0V
VIN = 100 mV
50
35
mA
Sinking VO = 0V
VIN = −100 mV
50
35
84
IS
Supply Current
0.790
1.1
1.1
1.3
mA
SR
Slew Rate (Note 10)
AV = +1, VO = 9 VPP
10% to 90%
V/μs
GBW
Gain Bandwidth
2.5
MHz
%
THD+N
Total Harmonic Distortion + Noise
0.02
f = 1 kHz, AV = 1, RL = 10 kΩ
en
in
Input Referred Voltage Noise Density
Input Referred Current Noise Density
f = 1 kHz
9
1
nV/
fA/
f = 100 kHz
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics
Tables.
www.national.com
4
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-
Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.
Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ >
TA.
Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality
Control (SQC) method.
Note 7: This parameter is guaranteed by design and/or characterization and is not tested in production.
Note 8: Positive current corresponds to current flowing into the device.
Note 9: The short circuit test is a momentary test.
Note 10: The number specified is the slower of positive and negative slew rates.
5
www.national.com
Connection Diagram
5-Pin SOT23
30142102
Top View
Ordering Information
Package
Part Number
Package Marking
Transport Media
NSC Drawing
MF05A
5-Pin SOT23
5-Pin SOT23
5-Pin SOT23
SM72501MFE
SM72501MF
SM72501MFX
S501
S501
S501
250 Units Tape and Reel
1000 Units Tape and Reel
3000 Units Tape and Reel
MF05A
MF05A
www.national.com
6
Typical Performance Characteristics Unless otherwise noted: TA = 25°C, VCM = VS/2, RL > 10 kΩ.
Offset Voltage Distribution
Offset Voltage Distribution
Offset Voltage Distribution
TCVOS Distribution
TCVOS Distribution
TCVOS Distribution
30142136
30142137
30142138
30142141
30142142
30142143
7
www.national.com
Offset Voltage vs. Temperature
Offset Voltage vs. Supply Voltage
Offset Voltage vs. VCM
CMRR vs. Frequency
Offset Voltage vs. VCM
Offset Voltage vs. VCM
30142106
30142150
30142107
30142109
30142110
30142108
www.national.com
8
Input Bias Current vs. VCM
Input Bias Current vs. VCM
Input Bias Current vs. VCM
Input Bias Current vs. VCM
Input Bias Current vs. VCM
Input Bias Current vs. VCM
30142130
30142146
30142131
30142147
30142148
30142149
9
www.national.com
PSRR vs. Frequency
Supply Current vs. Supply Voltage (Per Channel)
30142145
30142111
Sinking Current vs. Supply Voltage
Sourcing Current vs. Supply Voltage
30142113
30142112
Output Voltage vs. Output Current
Slew Rate vs. Supply Voltage
30142116
30142117
www.national.com
10
Open Loop Frequency Response
Open Loop Frequency Response
30142115
30142114
Large Signal Step Response
Small Signal Step Response
30142118
30142120
Large Signal Step Response
Small Signal Step Response
30142126
30142119
11
www.national.com
Input Voltage Noise vs. Frequency
Open Loop Gain vs. Output Voltage Swing
30142127
30142152
Output Swing High vs. Supply Voltage
Output Swing Low vs. Supply Voltage
30142133
30142135
Output Swing High vs. Supply Voltage
Output Swing Low vs. Supply Voltage
30142132
30142134
www.national.com
12
THD+N vs. Frequency
THD+N vs. Output Voltage
30142128
30142129
13
www.national.com
INPUT CAPACITANCE
Application Information
CMOS input stages inherently have low input bias current and
higher input referred voltage noise. The SM72501 enhances
this performance by having the low input bias current of only
±200 fA, as well as, a very low input referred voltage noise of
SM72501
The SM72501 is a low offset voltage, rail-to-rail input and out-
put precision amplifier with a CMOS input stage and wide
supply voltage range of 2.7V to 12V. The SM72501 has a very
low input bias current of only ±200 fA at room temperature.
9 nV/
. In order to achieve this a larger input stage has
been used. This larger input stage increases the input capac-
itance of the SM72501. The typical value of this input capac-
itance, CIN, for the SM72501 is 25 pF. The input capacitance
will interact with other impedances such as gain and feedback
resistors, which are seen on the inputs of the amplifier, to form
a pole. This pole will have little or no effect on the output of
the amplifier at low frequencies and DC conditions, but will
play a bigger role as the frequency increases. At higher fre-
quencies, the presence of this pole will decrease phase mar-
gin and will also cause gain peaking. In order to compensate
for the input capacitance, care must be taken in choosing the
feedback resistors. In addition to being selective in picking
values for the feedback resistor, a capacitor can be added to
the feedback path to increase stability.
The wide supply voltage range of 2.7V to 12V over the ex-
tensive temperature range of −40°C to 125°C makes the
SM72501 an excellent choice for low voltage precision appli-
cations with extensive temperature requirements.
The SM72501 has only ±37 μV of typical input referred offset
voltage and this offset is guaranteed to be less than ±500 μV
over temperature. This minimal offset voltage allows more
accurate signal detection and amplification in precision appli-
cations.
The low input bias current of only ±200 fA along with the low
input referred voltage noise of 9 nV/
superiority for use in sensor applications. Lower levels of
noise from the SM72501 means better signal fidelity and a
higher signal-to-noise ratio.
gives the SM72501
The DC gain of the circuit shown in Figure 2 is simply –R2/
R1.
National Semiconductor is heavily committed to precision
amplifiers and the market segment they serve. Technical sup-
port and extensive characterization data is available for sen-
sitive applications or applications with a constrained error
budget.
The SM72501 is offered in the space saving 5-Pin SOT23.
This small package is an ideal solution for area constrained
PC boards and portable electronics.
CAPACITIVE LOAD
The SM72501 can be connected as a non-inverting unity gain
follower. This configuration is the most sensitive to capacitive
loading.
The combination of a capacitive load placed on the output of
an amplifier along with the amplifier's output impedance cre-
ates a phase lag which in turn reduces the phase margin of
the amplifier. If the phase margin is significantly reduced, the
response will be either underdamped or it will oscillate.
30142144
FIGURE 2. Compensating for Input Capacitance
In order to drive heavier capacitive loads, an isolation resistor,
RISO, in Figure 1 should be used. By using this isolation re-
sistor, the capacitive load is isolated from the amplifier's
output, and hence, the pole caused by CL is no longer in the
feedback loop. The larger the value of RISO, the more stable
the output voltage will be. If values of RISO are sufficiently
large, the feedback loop will be stable, independent of the
value of CL. However, larger values of RISO result in reduced
output swing and reduced output current drive.
For the time being, ignore CF. The AC gain of the circuit in
Figure 2 can be calculated as follows:
This equation is rearranged to find the location of the two
poles:
(1)
As shown in Equation 1, as values of R1 and R2 are increased,
the magnitude of the poles is reduced, which in turn decreas-
es the bandwidth of the amplifier. Whenever possible, it is
best to choose smaller feedback resistors. Figure 3 shows the
effect of the feedback resistor on the bandwidth of the
SM72501.
30142121
FIGURE 1. Isolating Capacitive Load
www.national.com
14
DIODES BETWEEN THE INPUTS
The SM72501 has a set of anti-parallel diodes between the
input pins, as shown in Figure 5. These diodes are present to
protect the input stage of the amplifier. At the same time, they
limit the amount of differential input voltage that is allowed on
the input pins. A differential signal larger than one diode volt-
age drop might damage the diodes. The differential signal
between the inputs needs to be limited to ±300 mV or the input
current needs to be limited to ±10 mA.
30142154
FIGURE 3. Closed Loop Gain vs. Frequency
30142125
Equation 1 has two poles. In most cases, it is the presence of
pairs of poles that causes gain peaking. In order to eliminate
this effect, the poles should be placed in Butterworth position,
since poles in Butterworth position do not cause gain peaking.
To achieve a Butterworth pair, the quantity under the square
root in Equation 1 should be set to equal −1. Using this fact
and the relation between R1 and R2, R2 = −AV R1, the optimum
value for R1 can be found. This is shown in Equation 2. If R1
is chosen to be larger than this optimum value, gain peaking
will occur.
FIGURE 5. Input of SM72501
(2)
In Figure 2, CF is added to compensate for input capacitance
and to increase stability. Additionally, CF reduces or elimi-
nates the gain peaking that can be caused by having a larger
feedback resistor. Figure 4 shows how CF reduces gain peak-
ing.
30142155
FIGURE 4. Closed Loop Gain vs. Frequency with
Compensation
15
www.national.com
PRECISION CURRENT SOURCE
combination. This is because each individual amplifier acts as
an independent noise source, and the average noise of inde-
pendent sources is the quadrature sum of the independent
sources divided by the number of sources. For N identical
amplifiers, this means:
The SM72501 can be used as a precision current source in
many different applications. Figure 6 shows a typical preci-
sion current source. This circuit implements a precision volt-
age controlled current source. Amplifier A1 is a differential
amplifier that uses the voltage drop across RS as the feedback
signal. Amplifier A2 is a buffer that eliminates the error current
from the load side of the RS resistor that would flow in the
feedback resistor if it were connected to the load side of the
RS resistor. In general, the circuit is stable as long as the
closed loop bandwidth of amplifier A2 is greater then the
closed loop bandwidth of amplifier A1. Note that if A1 and A2
are the same type of amplifiers, then the feedback around A1
will reduce its bandwidth compared to A2.
Figure 7 shows a schematic of this input voltage noise reduc-
tion circuit. Typical resistor values are:
RG = 10Ω, RF = 1 kΩ, and RO = 1 kΩ.
30142105
FIGURE 6. Precision Current Source
The equation for output current can be derived as follows:
Solving for the current I results in the following equation:
LOW INPUT VOLTAGE NOISE
The SM72501 has a very low input voltage noise of 9 nV/
. This input voltage noise can be further reduced by plac-
ing N amplifiers in parallel as shown in Figure 7. The total
voltage noise on the output of this circuit is divided by the
square root of the number of amplifiers used in this parallel
30142156
FIGURE 7. Noise Reduction Circuit
www.national.com
16
TOTAL NOISE CONTRIBUTION
HIGH IMPEDANCE SENSOR INTERFACE
The SM72501 has very low input bias current, very low input
current noise, and very low input voltage noise. As a result,
these amplifiers are ideal choices for circuits with high
impedance sensor applications.
Many sensors have high source impedances that may range
up to 10 MΩ. The output signal of sensors often needs to be
amplified or otherwise conditioned by means of an amplifier.
The input bias current of this amplifier can load the sensor's
output and cause a voltage drop across the source resistance
as shown in Figure 9, where VIN+ = VS – IBIAS*RS
Figure 8 shows the typical input noise of the SM72501 as a
function of source resistance where:
The last term, IBIAS*RS, shows the voltage drop across RS. To
prevent errors introduced to the system due to this voltage,
an op amp with very low input bias current must be used with
high impedance sensors. This is to keep the error contribution
by IBIAS*RS less than the input voltage noise of the amplifier,
so that it will not become the dominant noise factor.
en denotes the input referred voltage noise
ei is the voltage drop across source resistance due to input
referred current noise or ei = RS * in
et shows the thermal noise of the source resistance
eni shows the total noise on the input.
Where:
The input current noise of the SM72501 is so low that it will
not become the dominant factor in the total noise unless
source resistance exceeds 300 MΩ, which is an unrealisti-
cally high value.
As is evident in Figure 8, at lower RS values, total noise is
dominated by the amplifier's input voltage noise. Once RS is
larger than a few kilo-Ohms, then the dominant noise factor
becomes the thermal noise of RS. As mentioned before, the
current noise will not be the dominant noise factor for any
practical application.
30142159
FIGURE 9. Noise Due to IBIAS
pH electrodes are very high impedance sensors. As their
name indicates, they are used to measure the pH of a solu-
tion. They usually do this by generating an output voltage
which is proportional to the pH of the solution. pH electrodes
are calibrated so that they have zero output for a neutral so-
lution, pH = 7, and positive and negative voltages for acidic
or alkaline solutions. This means that the output of a pH elec-
trode is bipolar and has to be level shifted to be used in a
single supply system. The rate of change of this voltage is
usually shown in mV/pH and is different for different pH sen-
sors. Temperature is also an important factor in a pH elec-
trode reading. The output voltage of the senor will change with
temperature.
Figure 10 shows a typical output voltage spectrum of a pH
electrode. Note that the exact values of output voltage will be
different for different sensors. In this example, the pH elec-
trode has an output voltage of 59.15 mV/pH at 25°C.
30142158
FIGURE 8. Total Input Noise
30142160
FIGURE 10. Output Voltage of a pH Electrode
The temperature dependence of a typical pH electrode is
shown in Figure 11. As is evident, the output voltage changes
with changes in temperature.
17
www.national.com
mation is used by the ADC to calculate the temperature
effects on the pH readings. The LM35 needs to have a resis-
tor, RT in Figure 12, to –V+ in order to be able to read
temperatures below 0°C. RT is not needed if temperatures are
not expected to go below zero.
The output of pH electrodes is usually large enough that it
does not require much amplification; however, due to the very
high impedance, the output of a pH electrode needs to be
buffered before it can go to an ADC. Since most ADCs are
operated on single supply, the output of the pH electrode also
needs to be level shifted. Amplifier A1 buffers the output of
the pH electrode with a moderate gain of +2, while A2 pro-
vides the level shifting. VOUT at the output of A2 is given by:
VOUT = −2VpH + 1.024V.
The LM4140A is a precision, low noise, voltage reference
used to provide the level shift needed. The ADC used in this
application is the ADC12032 which is a 12-bit, 2 channel con-
verter with multiplexers on the inputs and a serial output. The
12-bit ADC enables users to measure pH with an accuracy of
0.003 of a pH unit. Adequate power supply bypassing and
grounding is extremely important for ADCs. Recommended
bypass capacitors are shown in Figure 12. It is common to
share power supplies between different components in a cir-
cuit. To minimize the effects of power supply ripples caused
by other components, the op amps need to have bypass ca-
pacitors on the supply pins. Using the same value capacitors
as those used with the ADC are ideal. The combination of
these three values of capacitors ensures that AC noise
present on the power supply line is grounded and does not
interfere with the amplifiers' signal.
30142161
FIGURE 11. Temperature Dependence of a pH Electrode
The schematic shown in Figure 12 is a typical circuit which
can be used for pH measurement. The LM35 is a precision
integrated circuit temperature sensor. This sensor is differen-
tiated from similar products because it has an output voltage
linearly proportional to Celcius measurement, without the
need to convert the temperature to Kelvin. The LM35 is used
to measure the temperature of the solution and feeds this
reading to the Analog to Digital Converter, ADC. This infor-
30142162
FIGURE 12. pH Measurement Circuit
www.national.com
18
Physical Dimensions inches (millimeters) unless otherwise noted
5-Pin SOT23
NS Package Number MF05A
19
www.national.com
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
www.national.com/amplifiers
Design Support
www.national.com/webench
Amplifiers
WEBENCH® Tools
App Notes
Audio
www.national.com/audio
www.national.com/timing
www.national.com/adc
www.national.com/interface
www.national.com/lvds
www.national.com/power
www.national.com/appnotes
www.national.com/refdesigns
www.national.com/samples
www.national.com/evalboards
www.national.com/packaging
www.national.com/quality/green
www.national.com/contacts
www.national.com/quality
www.national.com/feedback
www.national.com/easy
Clock and Timing
Data Converters
Interface
Reference Designs
Samples
Eval Boards
LVDS
Packaging
Power Management
Green Compliance
Distributors
Switching Regulators www.national.com/switchers
LDOs
www.national.com/ldo
www.national.com/led
www.national.com/vref
www.national.com/powerwise
Quality and Reliability
Feedback/Support
Design Made Easy
Applications & Markets
Mil/Aero
LED Lighting
Voltage References
PowerWise® Solutions
www.national.com/solutions
www.national.com/milaero
www.national.com/solarmagic
www.national.com/training
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
PLL/VCO
www.national.com/tempsensors SolarMagic™
www.national.com/wireless
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
Email: support@nsc.com
Tel: 1-800-272-9959
www.national.com
相关型号:
©2020 ICPDF网 联系我们和版权申明