74AUP2G125_11 [NXP]
Low-power dual buffer/line driver; 3-state; 低功耗双缓冲/线路驱动器;三态型号: | 74AUP2G125_11 |
厂家: | NXP |
描述: | Low-power dual buffer/line driver; 3-state |
文件: | 总24页 (文件大小:150K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
74AUP2G125
Low-power dual buffer/line driver; 3-state
Rev. 8 — 2 December 2011
Product data sheet
1. General description
The 74AUP2G125 provides the dual non-inverting buffer/line driver with 3-state output.
The 3-state output is controlled by the output enable input (nOE). A HIGH level at pin nOE
causes the output to assume a high-impedance OFF-state. This device has the
input-disable feature, which allows floating input signals. The inputs are disabled when the
output enable input nOE) is HIGH.
Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall
times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low
static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V.
This device is fully specified for partial power-down applications using IOFF. The IOFF
circuitry disables the output, preventing a damaging backflow current through the device
when it is powered down.
2. Features and benefits
Wide supply voltage range from 0.8 V to 3.6 V
High noise immunity
Complies with JEDEC standards:
JESD8-12 (0.8 V to 1.3 V)
JESD8-11 (0.9 V to 1.65 V)
JESD8-7 (1.2 V to 1.95 V)
JESD8-5 (1.8 V to 2.7 V)
JESD8-B (2.7 V to 3.6 V)
ESD protection:
HBM JESD22-A114F Class 3A exceeds 5000 V
MM JESD22-A115-A exceeds 200 V
CDM JESD22-C101E exceeds 1000 V
Low static power consumption; ICC = 0.9 A (maximum)
Latch-up performance exceeds 100 mA per JESD78B Class II
Inputs accept voltages up to 3.6 V
Low noise overshoot and undershoot < 10 % of VCC
Input-disable feature allows floating input conditions
IOFF circuitry provides partial power-down mode operation
Multiple package options
Specified from 40 C to +85 C and 40 C to +125 C
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
3. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range Name
Description
Version
74AUP2G125DC
74AUP2G125GT
74AUP2G125GF
74AUP2G125GD
74AUP2G125GM
74AUP2G125GN
74AUP2G125GS
40 C to +125 C
40 C to +125 C
40 C to +125 C
40 C to +125 C
40 C to +125 C
40 C to +125 C
40 C to +125 C
VSSOP8 plastic very thin shrink small outline package; 8 leads; SOT765-1
body width 2.3 mm
XSON8
plastic extremely thin small outline package; no leads; SOT833-1
8 terminals; body 1 1.95 0.5 mm
XSON8
extremely thin small outline package; no leads;
SOT1089
8 terminals; body 1.35 1 0.5 mm
XSON8U plastic extremely thin small outline package; no leads; SOT996-2
8 terminals; UTLP based; body 3 2 0.5 mm
XQFN8U plastic extremely thin quad flat package; no leads;
SOT902-1
SOT1116
SOT1203
8 terminals; UTLP based; body 1.6 1.6 0.5 mm
XSON8
XSON8
extremely thin small outline package; no leads;
8 terminals; body 1.2 1.0 0.35 mm
extremely thin small outline package; no leads;
8 terminals; body 1.35 1.0 0.35 mm
4. Marking
Table 2.
Marking codes
Type number
Marking code[1]
74AUP2G125DC
74AUP2G125GT
74AUP2G125GF
74AUP2G125GD
74AUP2G125GM
74AUP2G125GN
74AUP2G125GS
p25
p25
aM
p25
p25
aM
aM
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
5. Functional diagram
1A
1Y
1OE
2A
1
EN1
2Y
2
2OE
EN2
001aah932
001aah931
Fig 1. Logic symbol
Fig 2. IEC logic symbol
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
2 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
nY
nA
nOE
mna227
Fig 3. Logic diagram (one gate)
6. Pinning information
6.1 Pinning
74AUP2G125
1OE
1A
1
2
3
4
8
7
6
5
V
CC
2OE
1Y
74AUP2G125
2Y
1
2
3
4
8
7
6
5
1OE
1A
V
CC
2OE
GND
2A
2Y
1Y
2A
GND
001aae974
Transparent top view
001aae973
Fig 4. Pin configuration SOT765-1
Fig 5. Pin configuration SOT833-1, SOT1089,
SOT1116 and SOT1203
74AUP2G125
terminal 1
index area
2OE
1
7
6
5
1OE
1A
74AUP2G125
1OE
1A
1
2
3
4
8
7
6
5
V
CC
1Y
2A
2
3
2OE
1Y
2Y
2Y
GND
2A
001aae975
001aaj471
Transparent top view
Transparent top view
Fig 6. Pin configuration SOT996-2
Fig 7. Pin configuration SOT902-1
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
3 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
6.2 Pin description
Table 3.
Symbol
Pin description
Pin
Description
SOT765-1, SOT833-1, SOT1089, SOT996-2,
SOT1116 and SOT1203
SOT902-1
1OE, 2OE
1A, 2A
GND
1, 7
2, 5
4
7, 1
6, 3
4
output enable input (active LOW)
data input
ground (0 V)
1Y, 2Y
VCC
6, 3
8
2, 5
8
data output
supply voltage
7. Functional description
Table 4.
Function table[1]
Input
nOE
L
Output
nA
L
nY
L
L
H
H
Z
H
X
[1] H = HIGH voltage level;
L = LOW voltage level;
X = don’t care;
Z = high-impedance OFF-state.
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
IIK
Parameter
Conditions
Min
0.5
50
0.5
50
0.5
-
Max
+4.6
-
Unit
V
supply voltage
input clamping current
input voltage
VI < 0 V
mA
V
[1]
[1]
VI
+4.6
-
IOK
output clamping current VO < 0 V
mA
V
VO
output voltage
Active mode and Power-down mode
+4.6
20
50
IO
output current
VO = 0 V to VCC
mA
mA
mA
C
ICC
supply current
-
IGND
Tstg
Ptot
ground current
50
65
-
-
storage temperature
total power dissipation
+150
250
[2]
Tamb = 40 C to +125 C
mW
[1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For VSSOP8 packages: above 110 C the value of Ptot derates linearly with 8.0 mW/K.
For XSON8, XSON8U and XQFN8U packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
4 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
9. Recommended operating conditions
Table 6.
Symbol
VCC
Operating conditions
Parameter
Conditions
Min
0.8
0
Max
3.6
Unit
V
supply voltage
input voltage
VI
3.6
V
VO
output voltage
Active mode
0
VCC
3.6
V
Power-down mode; VCC = 0 V
0
V
Tamb
ambient temperature
40
0
+125
200
C
ns/V
t/V
input transition rise and fall rate
VCC = 0.8 V to 3.6 V
10. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Tamb = 25 C
VIH
HIGH-level input voltage
VCC = 0.8 V
0.70 VCC
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
VCC = 0.8 V
0.65 VCC
-
1.6
-
2.0
-
VIL
LOW-level input voltage
-
-
-
-
0.30 VCC
0.35 VCC
0.7
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
VOH
HIGH-level output voltage VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
VCC 0.1
0.75 VCC
1.11
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VI = VIH or VIL
1.32
2.05
1.9
2.72
2.6
VOL
LOW-level output voltage
IO = 20 A; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
V
V
V
V
V
V
V
V
0.3 VCC
0.31
0.31
0.31
0.44
0.31
0.44
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
5 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
0.1
0.1
Unit
A
II
input leakage current
OFF-state output current
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
IOZ
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
A
IOFF
power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
0.2
0.2
A
A
IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
CC = 0 V to 0.2 V
V
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
-
-
-
-
-
-
0.5
40
110
1
A
A
A
A
[1]
[1]
[2]
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
V
CC = 3.3 V
nOE input; VI = VCC 0.6 V; IO = 0 A;
CC = 3.3 V
V
all inputs; VI = GND to 3.6 V;
nOE = GND; VCC = 0.8 V to 3.6 V
CI
input capacitance
output capacitance
VI = GND or VCC; VCC = 0 V to 3.6 V
output enabled; VO = GND; VCC = 0 V
-
-
-
0.8
1.4
1.3
-
-
-
pF
pF
pF
CO
output disabled; VO = GND or VCC
;
VCC = 0 V to 3.6 V
Tamb = 40 C to +85 C
VIH HIGH-level input voltage
VCC = 0.8 V
0.70 VCC
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
VCC = 0.8 V
0.65 VCC
-
1.6
-
2.0
-
VIL
LOW-level input voltage
-
-
-
-
0.30 VCC
0.35 VCC
0.7
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
VOH
HIGH-level output voltage VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VCC 0.1
0.7 VCC
1.03
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
1.30
1.97
1.85
2.67
2.55
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
6 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VOL
LOW-level output voltage
VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.1
V
0.3 VCC
0.37
0.35
0.33
0.45
0.33
0.45
0.5
0.5
V
V
V
V
V
V
V
II
input leakage current
A
A
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
IOFF
power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
0.5
0.6
A
A
IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
-
-
-
-
-
-
0.9
50
120
1
A
A
A
A
[1]
[1]
[2]
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
nOE input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
all inputs; VI = GND to 3.6 V;
nOE = GND; VCC = 0.8 V to 3.6 V
Tamb = 40 C to +125 C
VIH HIGH-level input voltage
VCC = 0.8 V
0.75 VCC
-
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
VCC = 0.8 V
0.70 VCC
-
1.6
-
2.0
-
VIL
LOW-level input voltage
-
-
-
-
0.25 VCC
0.30 VCC
0.7
VCC = 0.9 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
0.9
VOH
HIGH-level output voltage VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
VCC 0.11 -
-
-
-
-
-
-
-
-
V
V
V
V
V
V
V
V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
0.6 VCC
0.93
-
-
-
-
-
-
-
1.17
1.77
1.67
2.40
2.30
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
7 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VOL
LOW-level output voltage
VI = VIH or VIL
IO = 20 A; VCC = 0.8 V to 3.6 V
IO = 1.1 mA; VCC = 1.1 V
IO = 1.7 mA; VCC = 1.4 V
IO = 1.9 mA; VCC = 1.65 V
IO = 2.3 mA; VCC = 2.3 V
IO = 3.1 mA; VCC = 2.3 V
IO = 2.7 mA; VCC = 3.0 V
IO = 4.0 mA; VCC = 3.0 V
VI = GND to 3.6 V; VCC = 0 V to 3.6 V
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.11
V
0.33 VCC
0.41
V
V
0.39
V
0.36
V
0.50
V
0.36
V
0.50
V
II
input leakage current
0.75
0.75
A
A
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V
IOFF
power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V
-
-
-
-
0.75
0.75
A
A
IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
-
-
-
-
-
-
1.4
75
180
1
A
A
A
A
[1]
[1]
[2]
ICC
additional supply current
data input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
nOE input; VI = VCC 0.6 V; IO = 0 A;
VCC = 3.3 V
all inputs; VI = GND to 3.6 V;
nOE = GND; VCC = 0.8 V to 3.6 V
[1] One input at VCC 0.6 V, other input at VCC or GND.
[2] To show ICC remains very low when the input-disable feature is enabled.
11. Dynamic characteristics
Table 8.
Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min
Typ[1] Max Min
Max
Max
(85 C) (125 C)
CL = 5 pF
[2]
tpd
propagation delay nA to nY; see Figure 8
VCC = 0.8 V
-
20.6
5.5
3.9
3.2
2.6
2.4
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
2.8
2.2
1.9
1.6
1.4
10.5
6.1
4.8
3.6
3.1
2.5
2.0
1.7
1.4
1.2
11.7
7.3
6.1
4.3
3.9
12.9
8.1
6.7
4.9
4.4
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
8 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min
Typ[1] Max Min
Max
Max
(85 C) (125 C)
[3]
ten
enable time
nOE to nY; see Figure 9
VCC = 0.8 V
-
69.9
6.1
4.2
3.4
2.6
2.4
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
nOE to nY; see Figure 9
VCC = 0.8 V
3.1
2.5
2.1
1.8
1.7
11.8
6.6
5.1
3.7
3.1
2.9
2.3
2.0
1.7
1.7
13.9
7.7
6.2
4.5
3.5
15.4
8.3
6.8
5.0
3.9
[4]
tdis
disable time
-
14.3
4.3
3.2
3.0
2.2
2.5
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
2.7
2.1
2.0
1.4
1.7
6.5
4.4
4.3
2.9
3.2
2.7
2.1
2.0
1.4
1.7
7.3
5.1
5.0
3.3
3.4
8.2
5.7
5.7
4.1
3.9
CL = 10 pF
[2]
[3]
[4]
tpd
ten
tdis
propagation delay nA to nY; see Figure 8
VCC = 0.8 V
-
24.0
6.4
4.5
3.8
3.2
3.0
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
3.2
2.1
1.9
2.1
1.8
12.3
7.3
5.5
4.2
3.8
3.0
1.9
1.7
1.6
1.6
13.8
8.5
6.8
5.3
4.6
15.2
9.4
7.6
5.9
5.2
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
enable time
nOE to nY; see Figure 9
VCC = 0.8 V
-
73.7
6.9
4.8
3.9
3.2
3.0
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
nOE to nY; see Figure 9
VCC = 0.8 V
3.6
2.3
2.0
1.8
1.7
13.5
7.7
5.8
4.3
3.9
3.4
2.2
1.9
1.7
1.7
15.8
8.6
6.8
5.3
4.3
17.5
9.4
7.4
5.9
4.8
disable time
-
32.7
5.4
4.1
4.2
3.0
3.8
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
3.4
2.2
2.2
1.7
2.1
7.9
5.5
5.6
3.8
4.8
3.4
2.2
1.9
1.7
1.7
8.8
6.2
6.3
4.5
5.0
9.9
7.1
7.1
5.1
5.6
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
9 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min
Typ[1] Max Min
Max
Max
(85 C) (125 C)
CL = 15 pF
[2]
[3]
[4]
tpd
ten
tdis
propagation delay nA to nY; see Figure 8
VCC = 0.8 V
-
27.4
7.2
5.1
4.3
3.7
3.5
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
3.6
3.0
2.2
2.0
2.0
14.1
8.1
6.3
4.9
4.4
3.3
2.5
2.0
1.8
1.8
15.8
9.8
7.9
6.0
5.4
17.5
10.9
8.8
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
6.7
VCC = 3.0 V to 3.6 V
6.1
enable time
nOE to nY; see Figure 9
VCC = 0.8 V
-
77.5
7.7
5.3
4.4
3.6
3.5
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
nOE to nY; see Figure 9
VCC = 0.8 V
4.0
3.0
2.3
2.1
2.0
15.2
8.4
6.5
5.0
4.4
3.7
2.5
2.1
2.0
1.9
17.6
9.8
7.7
6.1
4.9
19.6
10.7
8.5
6.8
5.5
disable time
-
60.8
6.5
5.0
5.3
3.8
5.0
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
4.3
3.0
3.0
2.1
2.9
9.2
6.5
7.0
4.9
6.2
3.7
2.5
2.1
2.0
1.9
10.3
7.4
7.4
5.1
6.6
11.6
8.4
8.9
6.4
7.4
CL = 30 pF
tpd
[2]
propagation delay nA to nY; see Figure 8
VCC = 0.8 V
-
37.4
9.5
6.7
5.6
4.8
4.6
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
4.8
4.0
2.9
2.7
2.7
19.0
10.8
8.4
4.4
3.0
2.6
2.5
2.5
21.6
13.0
10.3
7.8
24.0
14.5
11.5
8.7
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
6.3
VCC = 3.0 V to 3.6 V
5.8
7.5
8.3
[3]
ten
enable time
nOE to nY; see Figure 9
VCC = 0.8 V
-
88.9
9.9
6.8
5.6
4.8
4.6
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
5.2
4.0
3.0
2.7
2.7
19.8
10.8
8.5
4.8
3.1
2.8
2.6
2.6
22.8
12.6
10.2
7.8
25.3
14.1
11.3
8.8
6.5
6.0
6.9
7.7
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
10 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 10.
Symbol Parameter
Conditions
25 C
40 C to +125 C
Unit
Min
Typ[1] Max Min
Max
Max
(85 C) (125 C)
[4]
tdis
disable time
nOE to nY; see Figure 9
VCC = 0.8 V
-
49.9
9.9
7.7
8.7
6.2
8.7
-
-
-
-
ns
ns
ns
ns
ns
ns
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
6.0
4.4
5.1
3.6
5.2
13.3
9.6
4.8
3.1
2.8
2.6
2.6
14.8
10.8
12.4
8.6
16.5
12.1
13.8
9.6
11.1
7.6
10.5
10.8
13.1
CL = 5 pF, 10 pF, 15 pF and 30 pF
[5]
CPD power dissipation output enabled; fi = 1 MHz;
capacitance
VI = GND to VCC
VCC = 0.8 V
-
-
-
-
-
-
2.7
2.8
2.9
3.0
3.6
4.2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
pF
pF
pF
pF
pF
pF
VCC = 1.1 V to 1.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 3.0 V to 3.6 V
[1] All typical values are measured at nominal VCC
.
[2]
t
pd is the same as tPLH and tPHL
.
[3] ten is the same as tPZH and tPZL
.
[4] tdis is the same as tPHZ and tPLZ
.
[5]
CPD is used to determine the dynamic power dissipation (PD in W).
PD = CPD VCC2 fi N + (CL VCC2 fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
(CL VCC2 fo) = sum of the outputs.
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
11 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
12. Waveforms
V
I
V
M
nA input
GND
t
t
PHL
PLH
V
OH
V
nY output
M
V
OL
mna230
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 8. The data input (nA) to output (nY) propagation delays
Table 9.
Measurement points
Supply voltage
VCC
Output
VM
Input
VM
VI
tr = tf
0.8 V to 3.6 V
0.5 VCC
0.5 VCC
VCC
3.0 ns
V
I
nOE input
V
M
GND
t
t
PZL
PLZ
V
CC
output
LOW-to-OFF
OFF-to-LOW
V
M
V
X
V
OL
t
t
PHZ
PZH
V
OH
V
Y
output
HIGH-to-OFF
OFF-to-HIGH
V
M
GND
outputs
enabled
outputs
enabled
outputs
disabled
mna362
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage levels that occur with the output load.
Fig 9. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
Output
VM
VM
VX
VY
0.8 V to 1.6 V
1.65 V to 2.7 V
3.0 V to 3.6 V
0.5 VCC
0.5 VCC
0.5 VCC
0.5 VCC
0.5 VCC
0.5 VCC
VOL + 0.1 V
VOL + 0.15 V
VOL + 0.3 V
VOH 0.1 V
VOH 0.15 V
VOH 0.3 V
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
12 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
V
V
EXT
CC
5 kΩ
V
V
O
I
G
DUT
R
T
C
L
R
L
001aac521
Test data is given in Table 11.
Definitions for test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
RT = Termination resistance should be equal to the output impedance Zo of the pulse generator.
VEXT = External voltage for measuring switching times.
Fig 10. Test circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
Load
VEXT
[1]
CL
RL
tPLH, tPHL
tPZH, tPHZ
tPZL, tPLZ
0.8 V to 3.6 V
5 pF, 10 pF, 15 pF and 30 pF
5 k or 1 M open
GND
2 VCC
[1] For measuring enable and disable times RL = 5 k.
For measuring propagation delays, set-up and hold times, and pulse width, RL = 1 M.
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
13 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
13. Package outline
VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm
SOT765-1
D
E
A
X
c
y
H
v
M
A
E
Z
5
8
Q
A
2
A
A
1
(A )
3
pin 1 index
θ
L
p
L
detail X
1
4
e
w
M
b
p
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(2)
(1)
A
A
A
b
c
D
E
e
H
L
L
p
Q
UNIT
v
w
y
Z
θ
1
2
3
p
E
max.
0.15
0.00
0.85
0.60
0.27
0.17
0.23
0.08
2.1
1.9
2.4
2.2
3.2
3.0
0.40
0.15
0.21
0.19
0.4
0.1
8°
0°
mm
1
0.5
0.12
0.4
0.2
0.13
0.1
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
02-06-07
SOT765-1
MO-187
Fig 11. Package outline SOT765-1 (VSSOP8)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
14 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm
SOT833-1
b
1
2
3
4
4×
(2)
L
L
1
e
8
7
6
5
e
1
e
1
e
1
8×
A
(2)
A
1
D
E
terminal 1
index area
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
A
A
1
UNIT
b
D
E
e
e
1
L
L
1
max max
0.25
0.17
2.0
1.9
1.05
0.95
0.35 0.40
0.27 0.32
mm
0.5 0.04
0.6
0.5
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
JEITA
- - -
07-11-14
07-12-07
SOT833-1
- - -
MO-252
Fig 12. Package outline SOT833-1 (XSON8)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
15 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.35 x 1 x 0.5 mm
SOT1089
E
terminal 1
index area
D
A
A
1
detail X
(2)
(4×)
e
L
(2)
(8×)
b
4
5
e
1
1
8
terminal 1
index area
L
1
X
0
0.5
1 mm
scale
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
L
1
1
max 0.5 0.04 0.20 1.40 1.05
0.35 0.40
0.15 1.35 1.00 0.55 0.35 0.30 0.35
0.12 1.30 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1089_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
10-04-09
10-04-12
SOT1089
MO-252
Fig 13. Package outline SOT1089 (XSON8)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
16 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8U: plastic extremely thin small outline package; no leads;
8 terminals; UTLP based; body 3 x 2 x 0.5 mm
SOT996-2
D
B
A
E
A
A
1
detail X
terminal 1
index area
e
1
C
M
M
v
C
C
A
B
b
e
L
1
y
1
y
w
C
1
4
L
2
L
8
5
X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
b
D
E
e
e
1
L
L
L
v
w
y
y
1
1
1
2
max
0.05 0.35
0.00 0.15
2.1
1.9
3.1
2.9
0.5
0.3
0.15
0.05
0.6
0.4
mm
0.5
0.5
1.5
0.1
0.05 0.05
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
- - -
JEDEC
JEITA
07-12-18
07-12-21
SOT996-2
- - -
Fig 14. Package outline SOT996-2 (XSON8U)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
17 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XQFN8U: plastic extremely thin quad flat package; no leads;
8 terminals; UTLP based; body 1.6 x 1.6 x 0.5 mm
SOT902-1
D
B
A
terminal 1
index area
E
A
A
1
detail X
e
L
1
e
C
y
C
1
y
L
M
M
∅ v
∅ w
C
C
A
B
4
5
6
7
3
2
metal area
not for soldering
e
1
b
e
1
1
terminal 1
index area
8
X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
1
b
D
E
e
e
1
L
L
v
w
y
y
1
1
max
0.05 0.25 1.65 1.65
0.00 0.15 1.55 1.55
0.35 0.15
0.25 0.05
mm
0.5
0.55
0.5
0.1
0.05 0.05 0.05
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
MO-255
JEITA
05-11-25
07-11-14
SOT902-1
- - -
- - -
Fig 15. Package outline SOT902-1 (XQFN8U)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
18 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.2 x 1.0 x 0.35 mm
SOT1116
b
4
(2)
1
2
3
(4×)
L
L
1
e
8
7
6
5
e
1
e
1
e
1
(2)
(8×)
A
1
A
D
E
terminal 1
index area
0
0.5
scale
1 mm
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
L
1
1
max 0.35 0.04 0.20 1.25 1.05
0.35 0.40
0.15 1.20 1.00 0.55 0.3 0.30 0.35
0.12 1.15 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1116_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
10-04-02
10-04-07
SOT1116
Fig 16. Package outline SOT1116 (XSON8)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
19 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
XSON8: extremely thin small outline package; no leads;
8 terminals; body 1.35 x 1.0 x 0.35 mm
SOT1203
b
4
(2)
(4×)
1
2
3
L
L
1
e
8
7
6
5
e
1
e
1
e
1
(2)
(8×)
A
1
A
D
E
terminal 1
index area
0
L
0.5
scale
1 mm
Dimensions
Unit
(1)
A
A
b
D
E
e
e
1
L
1
1
max 0.35 0.04 0.20 1.40 1.05
0.35 0.40
0.15 1.35 1.00 0.55 0.35 0.30 0.35
0.12 1.30 0.95 0.27 0.32
mm nom
min
Note
1. Including plating thickness.
2. Visible depending upon used manufacturing technology.
sot1203_po
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
10-04-02
10-04-06
SOT1203
Fig 17. Package outline SOT1203 (XSON8)
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
20 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
14. Abbreviations
Table 12. Abbreviations
Acronym
CDM
DUT
Description
Charged Device Model
Device Under Test
ElectroStatic Discharge
Human Body Model
Machine Model
ESD
HBM
MM
15. Revision history
Table 13. Revision history
Document ID
Release date
20111202
Data sheet status
Change notice
Supersedes
74AUP2G125 v.8
Modifications:
Product data sheet
-
74AUP2G125 v.7
• Legal pages updated.
74AUP2G125 v.7
74AUP2G125 v.6
74AUP2G125 v.5
74AUP2G125 v.4
74AUP2G125 v.3
74AUP2G125 v.2
74AUP2G125 v.1
20100921
20091127
20090202
20090122
20080409
20070419
20061017
Product data sheet
-
-
-
-
-
-
-
74AUP2G125 v.6
74AUP2G125 v.5
74AUP2G125 v.4
74AUP2G125 v.3
74AUP2G125 v.2
74AUP2G125 v.1
-
Product data sheet
Product data sheet
Product data sheet
Product data sheet
Product data sheet
Product data sheet
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
21 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
16.2 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
16.3 Disclaimers
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
22 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
74AUP2G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 2 December 2011
23 of 24
74AUP2G125
NXP Semiconductors
Low-power dual buffer/line driver; 3-state
18. Contents
1
2
3
4
5
General description. . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 5
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Dynamic characteristics . . . . . . . . . . . . . . . . . . 8
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 21
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 21
8
9
10
11
12
13
14
15
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 22
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 22
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 23
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 2 December 2011
Document identifier: 74AUP2G125
相关型号:
©2020 ICPDF网 联系我们和版权申明