74LVC16241ADG-T [NXP]
IC LVC/LCX/Z SERIES, QUAD 4-BIT DRIVER, TRUE OUTPUT, PDSO48, 6.10 MM, PLASTIC, SOT-362-1, TSSOP2-48, Bus Driver/Transceiver;型号: | 74LVC16241ADG-T |
厂家: | NXP |
描述: | IC LVC/LCX/Z SERIES, QUAD 4-BIT DRIVER, TRUE OUTPUT, PDSO48, 6.10 MM, PLASTIC, SOT-362-1, TSSOP2-48, Bus Driver/Transceiver 驱动 光电二极管 输出元件 |
文件: | 总12页 (文件大小:144K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
74LVC16241A
16-bit buffer/line driver (3-State)
Product specification
1997 Jul 29
Supersedes data of 1995 Dec 26
IC24 Data Handbook
Philips
Semiconductors
Philips Semiconductors
Product specification
16-bit buffer/line driver (3-State)
74LVC16241A
FEATURES
PIN CONFIGURATION
• 5 volt tolerant inputs/outputs for interfacing with 5V logic
48 2OE
1OE
1Y0
1Y1
1
2
3
• Wide supply voltage range of 1.2V to 3.6V
• Complies with JEDEC standard no. 8-1A
• CMOS low power consumption
47
46
45
1A0
1A1
GND
GND
1Y2
4
5
TM
• MULTIBYTE flow-through standard pin-out architecture
44 1A2
43 1A3
• Low inductance multiple power and ground pins for minimum
1Y3
6
7
8
9
noise and ground bounce
42
41
40
V
CC
V
CC
• Direct interface with TTL levels
2Y0
2Y1
2A0
2A1
39 GND
38 2A2
37 2A3
GND 10
2Y2 11
2Y3 12
3Y0 13
3Y1 14
GND 15
3Y2 16
3Y3 17
DESCRIPTION
The 74LVC16241A is a high-performance, low-power, low-voltage,
Si-gate CMOS device, superior to most advanced CMOS
compatible TTL families. Inputs can be driven from either 3.3V or 5V
devices. In 3-State operation, outputs can handle 5V. These
features allow the use of these devices in a mixed 3.3V/5V
environment.
36
3A0
35 3A1
34 GND
33 3A2
32 3A3
The 74LVC16241A is a 16-bit buffer/line driver with 3-State outputs.
The 3-State outputs are controlled by the output enable inputs nOE
and nOE. Schmitt-trigger action at all inputs makes the circuit highly
tolerant for slower input rise and fall times. The device can be used
as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer.
31
30
V
18
V
CC
CC
4A0
4A1
4Y0 19
4Y1 20
GND 21
4Y2 22
4Y3 23
4OE 24
29
28 GND
27 4A2
26
25
4A3
3OE
SW00049
QUICK REFERENCE DATA
GND = 0 V; T
= 25 _C; t = t v 2.5 ns
amb
r
f
SYMBOL
/t
PARAMETER
CONDITIONS
TYPICAL
UNIT
Propagation delay
nAn to nYn
C = 50pF
L
t
2.9
ns
PHL PLH
V
CC
= 3.3V
C
C
Input capacitance
5.0
25
pF
pF
I
1
Power dissipation capacitance per buffer
V = GND to V
I CC
PD
NOTES:
1. C is used to determine the dynamic power dissipation (P in mW):
PD
D
2
2
P
= C x V
x f + S (C x V
x f ) where:
D
PD
CC
i
L
CC o
f = input frequency in MHz; C = output load capacity in pF;
i
L
f = output frequency in MHz; V = supply voltage in V;
o
CC
2
S (C x V
x f ) = sum of outputs.
L
CC
o
ORDERING INFORMATION
PACKAGES
TEMPERATURE RANGE OUTSIDE NORTH AMERICA
NORTH AMERICA
VC16241A DL
DWG NUMBER
SOT370-1
48-Pin Plastic SSOP Type III
48-Pin Plastic TSSOP Type II
–40°C to +85°C
–40°C to +85°C
74LVC16241A DL
74LVC16241A DGG
VC16241A DGG
SOT362-1
2
1997 Jul 29
853-2006 18217
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
PIN DESCRIPTION
LOGIC SYMBOL (IEEE/IEC)
PIN NUMBER
SYMBOL
NAME AND FUNCTION
1
EN1
EN2
EN3
EN4
1OE
2OE
3OE
4OE
Output enable input
(active LOW)
1
1OE
48
25
24
2, 3, 5, 6
1Y0 to 1Y3
GND
Data outputs
Ground (0V)
4, 10, 15, 21,
28, 34, 39, 45
47
46
2
1A0
1A1
1A2
1A3
2A0
2A1
2A2
2A3
3A0
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
3Y0
1
1
1
1
1
2
3
4
3
5
7, 18, 31, 42
8, 9, 11, 12
V
Positive supply voltage
Data outputs
CC
44
43
41
2Y0 to 2Y3
3Y0 to 3Y3
4Y0 to 4Y3
6
8
9
13, 14, 16, 17
19, 20, 22, 23
Data outputs
40
38
Data outputs
11
12
Output enable input
(active LOW)
24
25
4OE
3OE
37
36
35
13
Output enable input
(active LOW)
14
16
3A1
3A2
3A3
4A0
4A1
4A2
4A3
3Y1
3Y2
3Y3
4Y0
4Y1
4Y2
4Y3
33
32
30, 29, 27, 26
36, 35, 33, 32
41, 40, 38, 37
47, 46, 44, 43
4A0 to 4A3
3A0 to 3A3
2A0 to 2A3
1A0 to 1A3
Data inputs
Data inputs
Data inputs
Data inputs
17
19
30
29
20
22
23
27
26
Output enable input
(active LOW)
48
2OE
SW00055
LOGIC SYMBOL
FUNCTION TABLES
INPUTS
OUTPUT
47
2
3
5
6
36
35
33
32
25
13
14
16
17
1A0
1Y0
1Y1
1Y2
1Y3
3A0
3A1
3A2
3A3
3OE
3Y0
3Y1
3Y2
3Y3
nOE
L
1An, 4An
1Yn, 4Yn
46
1A1
H
L
H
L
L
44
1A2
H
X
Z
43
1A3
INPUTS
OUTPUT
1
1OE
nOE
H
2An, 3An
2Yn, 3Yn
H
L
H
L
41
8
30
29
27
26
24
19
20
22
23
2A0
2Y0
2Y1
2Y2
2Y3
4A0
4A1
4A2
4A3
4OE
4Y0
4Y1
4Y2
4Y3
H
L
X
Z
40
9
2A1
H = HIGH voltage level
L = LOW voltage level
X = don’t care
38
11
12
2A2
Z = high impedance OFF-state
37
2A3
48
2OE
SW00146
3
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
CONDITIONS
UNIT
MAX.
MIN.
DC supply voltage (for max. speed
performance)
V
V
2.7
3.6
V
CC
DC supply voltage (for low-voltage
applications)
1.2
0
3.6
5.5
V
V
CC
V
DC Input voltage range
I
DC output voltage range; output HIGH or
LOW state
V
0
V
V
O
O
CC
V
DC output voltage range; output 3-State
0
5.5
V
Operating ambient temperature range in
free air
See DC and AC characteristics
for individual device
T
amb
–40
+85
°C
V
CC
V
CC
= 1.2 to 2.7V
= 2.7 to 3.6V
0
0
20
10
t , t
r
Input rise and fall times
ns/V
f
1
ABSOLUTE MAXIMUM RATINGS
In accordance with the Absolute Maximum Rating System (IEC 134) Voltages are referenced to GND (ground = 0V)
LIMITS
SYMBOL
PARAMETER
DC supply voltage
CONDITIONS
UNIT
MIN
–0.5
–
MAX
V
I
+6.5
–50
V
CC
DC input diode current
DC input voltage
V < 0
I
mA
V
IK
V
I
Note 2
–0.5
–
+6.5
I
DC output diode current
V
> V or V < 0
"50
mA
OK
O
CC
O
DC output voltage; output HIGH or LOW
state
V
Note 2
–0.5
V
+ 0.5
V
O
O
CC
V
I
DC output voltage; output 3-State
DC output source or sink current
Note 2
–0.5
–
6.5
V
V
O
= 0 to V
"50
"100
+150
mA
mA
°C
O
CC
I
, I
DC V or GND current
–
GND CC
CC
T
stg
Storage temperature range
Power dissipation per package
– SO package
–65
P
tot
Above +70°C derate linearly 8mW/K
Above +60°C derate linearly 5.5mW/K
500
500
mW
– SSOP and TSSOP package
NOTES:
1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability.
2. The input and output voltage ratings may be exceeded if the input and output clamp current ratings are observed.
4
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
DC ELECTRICAL CHARACTERISTICS
Over recommended operating conditions. Voltages are referenced to GND (ground = 0V)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C
UNIT
1
MIN
TYP
MAX
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
= 1.2V
V
CC
V
HIGH level Input voltage
LOW level Input voltage
V
V
IH
= 2.7 to 3.6V
2.0
= 1.2V
GND
0.8
V
IL
= 2.7 to 3.6V
= 2.7V; V = V or V ; I = –12mA
V
V
V
V
*0.5
I
IH
IL
O
CC
CC
CC
CC
= 3.0V; V = V or V ; I = –100µA
*0.2
*0.6
*0.8
V
I
IH
IL
O
O
O
CC
V
OH
HIGH level output voltage
LOW level output voltage
V
= 3.0V; V = V or V
I
I
= –18mA
= –24mA
I
IH
IL;
IL;
= 3.0V; V = V or V
I
IH
= 2.7V; V = V or V ; I = 12mA
0.40
0.20
0.55
5
"5
"10
20
I
IH
IL
O
= 3.0V; V = V or V ; I = 100µA
GND
V
OL
V
I
IH
IL
O
O
= 3.0V; V = V or V
I
= 24mA
I
IH
IL;
I
Input leakage current
= 3.6V; V = 5.5V or GND
0.1
0.1
µA
µA
µA
µA
I
I
I
3-State output OFF-state current
Power off leakage supply
Quiescent supply current
= 3.6V; V = V or V ; V = 5.5V or GND
OZ
I
IH
IL
O
I
off
= 0.0V; V or V = 5.5V
0.1
I
O
I
= 3.6V; V = V or GND; I = 0
0.1
CC
I
CC
O
Additional quiescent supply current
per input pin
∆I
CC
V
CC
= 2.7V to 3.6V; V = V –0.6V; I = 0
5
500
µA
I
CC
O
NOTE:
1. All typical values are at V = 3.3V and T
= 25°C.
CC
amb
AC CHARACTERISTICS
GND = 0V; t = t = 2.5ns; C = 50pF; R = 500Ω; T
= –40°C to +85°C.
R
F
L
L
amb
LIMITS
LIMITS
SYMBOL
PARAMETER
WAVEFORM
V
CC
= 3.3V ±0.3V
V
CC
= 2.7V
V = 1.2V
CC
UNIT
1
MIN
TYP
MAX
MIN
MAX
TYP
Propagation delay
nAn to nYn;
nAn to nYn
t
t
PHL
PLH
1, 4
3, 4
1.5
1.5
2.9
4.4
1.5
1.5
5.4
6.8
13
ns
ns
3-State output enable
time
1OE to 1Yn;
4OE to 4Yn
t
t
t
t
PZH
4.4
4.3
4.4
4.9
5.8
5.8
5.5
5.4
17
t
PZL
3-State output disable
time
1OE to 1Yn;
4OE to 4Yn
PHZ
3, 4
2, 4
2, 4
1.5
1.5
1.5
1.5
1.5
1.5
6.8
6.5
6.4
11
19
12
ns
ns
ns
t
PLZ
3-State output enable
time
2OE to 2Yn;
3OE to 3Yn
PZH
t
PZL
3-State output disable
time
2OE to 2Yn;
3OE to 3Yn
PHZ
t
PLZ
NOTE:
1. All typical values are at V = 3.3V and T
= 25°C.
amb
CC
5
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
AC WAVEFORMS
V
V
V
V
= 1.5V at V w 2.7V; V = 0.5 V at V t 2.7V.
M
OL
X
Y
CC
M
CC
CC
and V are the typical output voltage drop that occur with the output load.
OH
= V + 0.3V at V w 2.7V; V = V + 0.1 V at V t2.7V
OL
CC
X
OL
CC
CC
CC
= V –0.3V at V w2.7V; V = V – 0.1 V at V t2.7V
OH
CC
Y
OH
CC
V
I
V
I
1An, 2An
INPUT
1OE, 4OE
INPUT
V
V
M
M
GND
GND
t
t
PHL
PLH
V
t
t
PZL
OH
PLZ
V
CC
1Yn, 2Yn
OUTPUT
V
M
OUTPUT
LOW-to-OFF
OFF-to-LOW
V
M
V
OL
V
X
V
OL
SW00051
t
t
Waveform 1. Input (nAn) to output (nYn) propagation times
PHZ
PZH
V
OH
V
OUTPUT
Y
HIGH-to-OFF
OFF-to-HIGH
V
V
I
M
2OE, 3OE
INPUT
V
GND
M
outputs
enabled
outputs
disabled
outputs
enabled
GND
SW00052
t
t
PZL
PLZ
Waveform 3. 3-State enable and disable times for the input
(1OE, 4OE)
V
CC
OUTPUT
LOW-to-OFF
OFF-to-LOW
TEST CIRCUIT
V
M
V
X
S
1
V
V
CC
OL
2<V
CC
Open
GND
t
t
PZH
PHZ
R =500 Ω
L
V
OH
V
V
OUT
IN
V
OUTPUT
HIGH-to-OFF
OFF-to-HIGH
Y
PULSE
GENERATOR
D.U.T.
V
M
R =500 Ω
L
R
C
T
GND
L
outputs
enabled
outputs
disabled
outputs
enabled
Test Circuit for 3-State Outputs
SWITCH POSITION
SW00053
Waveform 2. 3-State enable and disable times for the input
(2OE, 3OE)
V
V
IN
TEST
SWITCH
Open
CC
t 2.7V
V
CC
t
/t
PLH PHL
2.7 – 3.6V 2.7V
t
/t
2<V
PLZ PZL
CC
t
/t
GND
PHZ PZH
DEFINITIONS
R = Load resistor
L
C = Load capacitance includes jig and probe capacitance
L
R = Termination resistance should be equal to Z
T
OUT
of pulse generators.
SW00047
Waveform 4. Load circuitry for switching times
6
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm
SOT370-1
7
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm
SOT362-1
8
1997 Jul 29
Philips Semiconductors
Product specification
74LVC16241A
16-bit buffer/line driver (3-State)
NOTES
9
1997 Jul 29
Philips Semiconductors
Product specification
16-bit buffer/line driver (3-State)
74LVC16241A
DEFINITIONS
Data Sheet Identification
Product Status
Definition
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Objective Specification
Formative or in Design
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Preliminary Specification
Product Specification
Preproduction Product
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. PhilipsSemiconductorsmakesnorepresentationorwarrantythatsuchapplicationswillbesuitableforthespecifiedusewithoutfurthertesting
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
orsystemswheremalfunctionofaPhilipsSemiconductorsandPhilipsElectronicsNorthAmericaCorporationProductcanreasonablybeexpected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Date of release: 05-96
9397-750-04527
Document order number:
Philips
Semiconductors
it Q
Philips Semiconductors Home
ProducBuy
MySemContac
Product Information
catalogonline
Information as of 2003-04-22
My.Semiconductors.COM.
Your personal service from Use right mouse button to
Philips Semiconductors.
Please register now !
Stay informed
74LVC16241A; 16-
bit buffer/line driver
(3-State)
download datasheet
Download datasheet
Products
General description
Features
Applications
Datasheet
Buy online
Parametrics
Email/translate
Block diagram
Products & packages
Support & tools
Similar products
MultiMarket
Semiconductors
•
•
•
Product Selector
Catalog by
Function
General description
The 74LVC16241A is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced
CMOS compatible TTL families. Inputs can be driven from either 3.3V or 5V devices. In 3-State operation, outputs can
handle 5V. These features allow the use of these devices in a mixed 3.3V/5V environment.
Catalog by
System
•
Cross-reference
Packages
•
•
The 74LVC16241A is a 16-bit buffer/line driver with 3-State outputs. The 3-State outputs are controlled by the output
enable inputs nOE and nOE. Schmitt-trigger action at all inputs makes the circuit highly tolerant for slower input rise and
fall times. The device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer.
End of Life
information
Distributors Go
Here!
•
•
Models
Features
•
•
SoC solutions
●
●
●
●
●
●
●
5 volt tolerant inputs/outputs for interfacing with 5V logic
Wide supply voltage range of 1.2V to 3.6V
Complies with JEDEC standard no. 8-1A
CMOS low power consumption
MULTIBYTE flow-through standard pin-out architecture
Low inductance multiple power and ground pins for minimum noise and ground bounce
Direct interface with TTL levels
TM
Applications
AN240: Interfacing 3 Volt and 5 Volt Applications
Datasheet
Type number Title
Publication release Datasheet status
date
Page
count
File size Datasheet
(kB)
74LVC16241A 16-bit buffer/line 7/29/1997
driver (3-State)
Product specification 10
88
Download
Parametrics
Type number
Package
Description Propagation Voltage No. Power
Delay(ns) of Dissipation
Logic
Switching Drive
Output
Pins Considerations Levels
Capability
3.3V 16-Bit
Buffer/Line
Driver; Non- 4~6
Inverting (3-
State)
Low Power or
48 Battery
Applications
SOT362-1
(TSSOP48)
74LVC16241ADGG
74LVC16241ADL
Low
Low
TTL
TTL
Medium
3.3V 16-Bit
Buffer/Line
Driver; Non- 4~6
Inverting (3-
State)
Low Power or
48 Battery
Applications
SOT370-1
(SSOP48)
Medium
Products, packages, availability and ordering
Type number
North American Ordering code Marking/Packing Package Device
Buy online
IC packing info
type number
(12NC)
status
SOT362-1
Standard Marking
* Tube
Full production
74LVC16241ADGG 74LVC16241ADG 9352 351 30112
(TSSOP48)
-
Standard Marking
SMD, 13"
SOT362-1
74LVC16241ADG-
T
Full production
Full production
Full production
9352 351 30118 * Reel Pack,
(TSSOP48)
SOT370-1
(SSOP48)
Standard Marking
* Tube
74LVC16241ADL 74LVC16241ADL 9352 351 20112
74LVC16241ADL-
Standard Marking
9352 351 20118 * Reel Pack,
SOT370-1
(SSOP48)
T
SMD, 13"
Similar products
74LVC16241A links to the similar products page containing an overview of products that are similar in function or
related to the type number(s) as listed on this page. The similar products page includes products from the same catalog
tree(s), relevant selection guides and products from the same functional category.
Email/translate this product information
●
●
Email this product information.
Translate this product information page from English to:
French
Translate
The English language is the official language used at the semiconductors.philips.com website and webpages. All translations
on this website are created through the use of Google Language Tools and are provided for convenience purposes only. No
rights can be derived from any translation on this website.
About this Web Site
| Copyright © 2003 Koninklijke Philips N.V. All rights reserved. | Privacy Policy |
| Koninklijke Philips N.V. | Access to and use of this Web Site is subject to the following Terms of Use. |
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 216
-
VISHAY
©2020 ICPDF网 联系我们和版权申明