74LVC2245APW [NXP]
Octal transceiver with direction pin; 30 ohm series termination resistors; 5 V input/output tolerant; 3-state; 八路收发器的方向针; 30欧姆的串联端接电阻器; 5 V输入/输出宽容;三态型号: | 74LVC2245APW |
厂家: | NXP |
描述: | Octal transceiver with direction pin; 30 ohm series termination resistors; 5 V input/output tolerant; 3-state |
文件: | 总17页 (文件大小:106K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
74LVC2245A
Octal transceiver with direction pin,
30 Ω series termination resistors;
5 V tolerant input/output; 3-state
Product specification
2003 Nov 17
Supersedes data of 2002 Jun 10
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
FEATURES
DESCRIPTION
• 5 V tolerant inputs/outputs for interfacing with 5 V logic
• Wide supply voltage range from 1.2 to 3.6 V
• CMOS low power consumption
The 74LVC2245A is a high-performance, low-power,
low-voltage, Si-gate CMOS device, superior to most
advanced CMOS compatible TTL families.
Inputs can be driven from either 3.3 or 5 V devices. In
3-state operation, outputs can handle 5 V. These features
allow the use of these devices as translators in a mixed
3.3 and 5 V environment.
• Direct interface with TTL levels
• Inputs accept voltages up to 5.5 V
• Integrated 30 Ω termination resistors
• Complies with JEDEC standard no. 8-1A
The 74LVC2245A is an octal transceiver featuring
non-inverting 3-state bus compatible outputs in both send
and receive directions.
• ESD protection:
HBM EIA/JESD22-A114-A exceeds 2000 V
MM EIA/JESD22-A115-A exceeds 200 V.
The 74LVC2245A features an output enable (OE) input for
easy cascading and a send/receive (DIR) input for
direction control. OE controls the outputs so that the buses
are effectively isolated.
• Specified from −40 to +85 °C and −40 to +125 °C.
The 74LVC2245A is designed with 30 Ω series termination
resistors in both HIGH and LOW output stages to reduce
line noise.
QUICK REFERENCE DATA
GND = 0 V; Tamb = 25 °C; tr = tf ≤ 2.5 ns.
SYMBOL
PARAMETER
propagation delay An to Bn, Bn to An
input capacitance
CONDITIONS
TYPICAL
3.6
UNIT
t
PHL/tPLH
CL = 50 pF; VCC = 3.3 V
ns
pF
pF
CI
4.0
13
CPD
power dissipation capacitance per buffer
VCC = 3.3 V; notes 1 and 2
Notes
1. CPD is used to determine the dynamic power dissipation (PD in µW).
PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in Volts;
N = total load switching outputs;
Σ(CL × VCC2 × fo) = sum of the outputs.
2. The condition is VI = GND to VCC
.
2003 Nov 17
2
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
TEMPERATURE RANGE
PINS
PACKAGE
MATERIAL
CODE
74LVC2245AD
74LVC2245ADB
74LVC2245APW
74LVC2245ABQ
−40 to +125 °C
−40 to +125 °C
−40 to +125 °C
−40 to +125 °C
20
20
20
20
SO20
plastic
plastic
plastic
plastic
SOT163-1
SOT339-1
SOT360-1
SOT764-1
SSOP20
TSSOP20
DHVQFN20
FUNCTION TABLE
See note 1.
INPUT
INPUT/OUTPUT
OE
DIR
An
Bn
L
L
L
H
X
A = B
input
Z
input
B = A
Z
H
Note
1. H = HIGH voltage level;
L = LOW voltage level;
X = don’t care;
Z = high-impedance OFF-state.
PINNING
PIN
SYMBOL
DESCRIPTION
PIN
1
SYMBOL
DIR
DESCRIPTION
direction control input
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
ground (0 V)
11
12
13
14
15
16
17
18
19
B7
B5
B5
B4
B3
B2
B1
B0
OE
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
data input/output
2
A0
A1
A2
A3
A4
A5
A6
A7
GND
3
4
5
6
7
8
output enable input
(active LOW)
9
20
VCC
supply voltage
10
2003 Nov 17
3
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
V
handbook, halfpage
DIR
1
CC
20
handbook, halfpage
V
DIR
1
2
20
19
18
17
16
CC
19 2OE
18 B0
17 B1
16 B2
15 B3
14 B4
13 B5
12 B6
A0
A1
A2
A3
A4
A5
A6
A7
2
3
4
5
6
7
8
9
OE
B0
B1
B2
A0
A1
3
4
A2
A3
5
2245
(1)
GND
6
15 B3
14 B4
A4
7
A5
8
13
12
B5
B6
A6
9
A7
GND
10
11 B7
MNA363
10
11
GND B7
Top view
MNB148
(1) The die substrate is attached to this pad using conductive die
attach material. It can not be used as a supply pin or input.
Fig.1 Pin configuration SO20 and (T)SSOP20.
Fig.2 Pin configuration DHVQFN20.
2003 Nov 17
4
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
handbook, halfpage
DIR
1
OE
19
A0
2
19
B0
18
handbook, halfpage
G3
3EN1 (BA)
3EN2 (AB)
A1
A2
A3
A4
A5
A6
A7
3
4
1
B1
17
1
18
2
B2
16
2
3
4
5
6
7
8
9
17
16
15
14
13
12
11
5
6
7
B3
15
B4
14
B5
13
8
9
MNA365
B6
12
B7
11
MNA174
Fig.3 Logic symbol (IEEE/IEC).
Fig.4 Logic symbol.
2003 Nov 17
5
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
supply voltage
CONDITIONS
MIN.
2.7
MAX.
3.6
UNIT
VCC
for maximum speed
performance
V
for low-voltage applications 1.2
0
3.6
5.5
VCC
5.5
+125
20
V
VI
input voltage
V
VO
output voltage
output HIGH or LOW state
output 3-state
0
V
0
V
Tamb
tr, tf
ambient temperature
−40
0
°C
input rise and fall times
VCC = 1.2 to 2.7 V
VCC = 2.7 to 3.6 V
ns/V
ns/V
0
10
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V).
SYMBOL
PARAMETER
supply voltage
CONDITIONS
MIN.
−0.5
MAX.
+6.5
UNIT
VCC
IIK
V
input diode current
input voltage
VI < 0
note 1
−
−50
mA
V
VI
−0.5
−
+6.5
IOK
VO
output diode current
output voltage
VO > VCC or VO < 0
±50
mA
V
output HIGH or LOW state; −0.5
VCC + 0.5
note 1
output 3-state; note 1
VO = 0 to VCC
−0.5
−
+6.5
±50
V
IO
output source or sink current
mA
mA
°C
ICC, IGND VCC or GND current
−
±100
+150
500
Tstg
Ptot
storage temperature
power dissipation
−65
−
Tamb = −40 to +125 °C;
mW
note 2
Notes
1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. For SO20 packages: above 70 °C derate linearly with 8 mW/K.
For SSOP20 and TSSOP20 packages: above 60 °C derate linearly with 5.5 mW/K.
For DHVQFN20 packages: above 60 °C derate linearly with 4.5 mW/K.
2003 Nov 17
6
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
DC CHARACTERISTICS
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
TEST CONDITIONS
SYMBOL
PARAMETER
MIN.
TYP.(1) MAX.
UNIT
OTHER
VCC (V)
Tamb = −40 to +85 °C
VIH
VIL
HIGH-level input voltage
1.2
VCC
−
−
−
−
−
V
V
V
V
2.7 to 3.6
1.2
2.0
−
−
LOW-level input voltage
0
2.7 to 3.6
−
0.8
VOH
HIGH-level output voltage VI = VIH or VIL
IO = −100 µA
IO = −6 mA
IO = −12 mA
2.7 to 3.6
2.7
V
V
V
CC − 0.2
VCC
−
−
−
−
V
V
V
CC − 0.5
CC − 0.8
3.0
−
VOL
LOW-level output voltage
VI = VIH or VIL
IO = 100 µA
IO = 6 mA
2.7 to 3.6
2.7
−
−
−
−
−
0
0.2
0.4
0.55
±5
V
V
V
−
IO = 12 mA
3.0
−
ILI
input leakage current
VI = 5.5 V or GND
3.6
±0.1
±0.1
µA
µA
IOZ
3-state output OFF-state
current
VI = VIH or VIL;
VO = 5.5 V or GND
3.6
±5
Ioff
power off leakage supply
quiescent supply current
VI or VO = 5.5 V
0.0
3.6
−
−
±0.1
±10
µA
µA
ICC
VI = VCC or GND;
IO = 0
0.1
10
∆ICC
additional quiescent supply VI = VCC − 0.6 V;
current per pin IO = 0
2.7 to 3.6
−
5
500
µA
2003 Nov 17
7
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
TEST CONDITIONS
SYMBOL
PARAMETER
MIN.
TYP.(1) MAX.
UNIT
OTHER
VCC (V)
Tamb = −40 to +125 °C
VIH
HIGH-level input voltage
LOW-level input voltage
1.2
VCC
−
−
−
−
−
V
V
V
V
2.7 to 3.6
1.2
2.0
−
−
VIL
0
2.7 to 3.6
−
0.8
VOH
HIGH-level output voltage VI = VIH or VIL
IO = −100 µA
IO = −6 mA
IO = −12 mA
2.7 to 3.6
2.7
V
V
V
CC − 0.3
−
−
−
−
−
−
V
V
V
CC − 0.65
CC − 1
3.0
VOL
LOW-level output voltage
VI = VIH or VIL
IO = 100 µA
IO = 6 mA
2.7 to 3.6
2.7
−
−
−
−
−
−
−
−
−
−
0.3
0.6
0.8
±20
±20
V
V
V
IO = 12 mA
3.0
ILI
input leakage current
VI = 5.5 V or GND
3.6
µA
µA
IOZ
3-state output OFF-state
current
VI = VIH or VIL;
VO = 5.5 V or GND
3.6
Ioff
power off leakage supply
quiescent supply current
VI or VO = 5.5 V
0.0
3.6
−
−
−
−
±20
µA
µA
ICC
VI = VCC or GND;
IO = 0
40
∆ICC
additional quiescent supply VI = VCC − 0.6 V;
current per pin IO = 0
2.7 to 3.6
−
−
5000 µA
Note
1. All typical values are measured at VCC = 3.3 V and Tamb = 25 °C.
2003 Nov 17
8
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
AC CHARACTERISTICS
GND = 0 V; tr = tf ≤ 2.5 ns.
TEST CONDITIONS
SYMBOL
PARAMETER
MIN.
TYP.
MAX.
UNIT
WAVEFORMS
VCC (V)
Tamb = −40 to +85 °C
tPHL/tPLH
propagation delay An to Bn; Bn to An
see Figs 5 and 7 1.2
2.7
−
26
−
ns
1.5
4.0
3.6(1)
7.3
6.3
−
ns
ns
ns
ns
ns
ns
ns
ns
ns
3.0 to 3.6 1.5
tPZH/tPZL
3-state output enable time
OE to An; OE to Bn
see Figs 6 and 7 1.2
2.7
−
28
1.5
5.9
9.5
8.2
−
3.0 to 3.6 1.5
4.3(1)
12.0
3.8
tPHZ/tPLZ
3-state output disable time
OE to An; OE to Bn
see Figs 6 and 7 1.2
2.7
−
1.5
6.9
5.9
1.0
3.0 to 3.6 1.7
3.4(1)
tsk(0)
skew
note 2
−
−
Tamb = −40 to +125 °C
tPHL/tPLH propagation delay nAn to nYn
see Figs 5 and 7 1.2
2.7
−
13
−
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
1.5
4.5
3.6(1)
20
9.5
8.0
−
3.0 to 3.6 1.5
tPZH/tPZL
3-state output enable time nOE to nYn see Figs 6 and 7 1.2
2.7
−
1.5
5.9
4.3(1)
10
12.0
10.5
−
3.0 to 3.6 1.5
tPHZ/tPLZ
3-state output disable time nOE to nYn see Figs 6 and 7 1.2
2.7
−
1.5
3.8
3.4(1)
−
9.0
7.5
1.5
3.0 to 3.6 1.7
tsk(0)
skew
note 2
−
Notes
1. Typical values are measured at VCC = 3.3 V.
2. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed
by design.
2003 Nov 17
9
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
AC WAVEFORMS
V
handbook, halfpage
I
An, Bn input
GND
V
V
M
M
t
t
PLH
PHL
V
OH
V
V
M
Bn, An output
M
V
OL
MNA176
INPUT
VCC
VM
VI
tr = tf
1.2 V
2.7 V
0.5 × VCC VCC
≤ 2.5 ns
≤ 2.5 ns
≤ 2.5 ns
1.5 V
1.5 V
2.7 V
2.7 V
3.0 to 3.6 V
VOL and VOH are typical output voltage drop that occur with the output load.
Fig.5 The inputs An, Bn to outputs Bn, An propagation delays.
V
I
OE input
V
M
t
GND
t
PLZ
PZL
V
CC
Q
output
n
V
LOW-to-OFF
OFF-to-LOW
M
V
X
V
OL
t
t
PHZ
PZH
V
OH
V
Y
Q
output
n
HIGH-to-OFF
OFF-to-HIGH
V
M
GND
outputs
enabled
outputs
enabled
outputs
disabled
MNA395
INPUT
tr = tf
VX = VOL + 0.3 V at VCC ≥ 2.7 V;
VX = VOL + 0.1 V at VCC < 2.7 V;
VY = VOH − 0.3 V at VCC ≥ 2.7 V;
VY = VOH − 0.1 V at VCC < 2.7 V.
VCC
VM
VI
0.5 × VCC VCC
1.5 V 2.7 V
2.7 V
1.2 V
2.7 V
≤ 2.5 ns
≤ 2.5 ns
≤ 2.5 ns
VOL and VOH are typical output voltage drop that occur with the output load.
3.0 to 3.6 V 1.5 V
Fig.6 3-state enable and disable times.
10
2003 Nov 17
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
V
EXT
V
CC
R
L
V
V
O
I
PULSE
GENERATOR
D.U.T.
C
R
R
L
L
T
MNA616
VEXT
tPLH/tPHL tPZH/tPHZ tPZL/tPLZ
VCC
VI
VCC
CL
RL
1.2 V
50 pF
50 pF
50 pF
500 Ω(1) open
GND
GND
GND
2 × VCC
2 × VCC
2 × VCC
2.7 V
2.7 V
2.7 V
500 Ω
500 Ω
open
open
3.0 to 3.6 V
Note
1. The circuit performs better when RL = 1000 Ω
Definitions for test circuit:
RL = Load resistor.
CL = Load capacitance including jig and probe capacitance.
RT = Termination resistance should be equal to the output impedance Zo of the pulse generator.
Fig.7 Load circuitry for switching times.
2003 Nov 17
11
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
PACKAGE OUTLINES
SO20: plastic small outline package; 20 leads; body width 7.5 mm
SOT163-1
D
E
A
X
c
y
H
E
v
M
A
Z
20
11
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
10
w
detail X
e
M
b
p
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
max.
(1)
(1)
(1)
UNIT
mm
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
θ
1
2
3
p
E
p
Z
0.3
0.1
2.45
2.25
0.49
0.36
0.32
0.23
13.0
12.6
7.6
7.4
10.65
10.00
1.1
0.4
1.1
1.0
0.9
0.4
2.65
0.1
0.25
0.01
1.27
0.05
1.4
0.25 0.25
0.1
8o
0o
0.012 0.096
0.004 0.089
0.019 0.013 0.51
0.014 0.009 0.49
0.30
0.29
0.419
0.394
0.043 0.043
0.016 0.039
0.035
0.016
inches
0.055
0.01 0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT163-1
075E04
MS-013
2003 Nov 17
12
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
SSOP20: plastic shrink small outline package; 20 leads; body width 5.3 mm
SOT339-1
D
E
A
X
c
H
v
M
A
y
E
Z
20
11
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
10
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
1
2
3
p
E
p
max.
8o
0o
0.21
0.05
1.80
1.65
0.38
0.25
0.20
0.09
7.4
7.0
5.4
5.2
7.9
7.6
1.03
0.63
0.9
0.7
0.9
0.5
mm
2
0.65
0.25
1.25
0.2
0.13
0.1
Note
1. Plastic or metal protrusions of 0.2 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT339-1
MO-150
2003 Nov 17
13
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm
SOT360-1
D
E
A
X
c
H
v
M
A
y
E
Z
11
20
Q
A
2
(A )
3
A
A
1
pin 1 index
θ
L
p
L
1
10
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(2)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
1
2
3
p
E
p
max.
8o
0o
0.15
0.05
0.95
0.80
0.30
0.19
0.2
0.1
6.6
6.4
4.5
4.3
6.6
6.2
0.75
0.50
0.4
0.3
0.5
0.2
mm
1.1
0.65
0.25
1
0.2
0.13
0.1
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT360-1
MO-153
2003 Nov 17
14
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
DHVQFN20: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
20 terminals; body 2.5 x 4.5 x 0.85 mm
SOT764-1
B
A
D
A
A
1
E
c
detail X
terminal 1
index area
C
terminal 1
index area
e
1
y
y
e
b
v
M
C
C
A
B
C
1
w
M
2
9
L
1
10
E
h
e
20
11
19
12
D
h
X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
A
(1)
(1)
UNIT
A
b
c
E
e
e
1
y
D
D
E
L
v
w
y
1
1
h
h
max.
0.05 0.30
0.00 0.18
4.6
4.4
3.15
2.85
2.6
2.4
1.15
0.85
0.5
0.3
mm
0.05
0.1
1
0.2
0.5
3.5
0.1
0.05
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
02-10-17
03-01-27
SOT764-1
- - -
MO-241
- - -
2003 Nov 17
15
Philips Semiconductors
Product specification
Octal transceiver with direction pin, 30 Ω series
termination resistors; 5 V tolerant input/output; 3-state
74LVC2245A
DATA SHEET STATUS
DATA SHEET
STATUS(1)
PRODUCT
STATUS(2)(3)
LEVEL
DEFINITION
I
Objective data
Development This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
II
Preliminary data Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
III
Product data
Production
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
DEFINITIONS
DISCLAIMERS
Short-form specification
The data in a short-form
Life support applications
These products are not
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
Right to make changes
Philips Semiconductors
reserves the right to make changes in the products -
including circuits, standard cells, and/or software -
described or contained herein in order to improve design
and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
Application information
Applications that are
communicated via a Customer Product/Process Change
Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these
products, conveys no licence or title under any patent,
copyright, or mask work right to these products, and
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
2003 Nov 17
16
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
© Koninklijke Philips Electronics N.V. 2003
SCA75
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
613508/04/pp17
Date of release: 2003 Nov 17
Document order number: 9397 750 10561
相关型号:
74LVC2245APW-T
LVC/LCX/Z SERIES, 8-BIT TRANSCEIVER, TRUE OUTPUT, PDSO20, 4.40 MM, PLASTIC, MO-153, SOT-360-1, TSSOP-20
PHILIPS
74LVC2245APWDH
Octal transceiver with direction pin; 30 ohm series termination resistors; 5 V input/output tolerant; 3-state
NXP
74LVC22952AD-T
IC LVC/LCX/Z SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24, Bus Driver/Transceiver
NXP
74LVC22952ADB-T
IC LVC/LCX/Z SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24, Bus Driver/Transceiver
NXP
74LVC22952APW-T
IC LVC/LCX/Z SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24, Bus Driver/Transceiver
NXP
74LVC2373A
Octal D-type transparent latch with 5-volt tolerant inputs/outputs; damping resistor 3-State
NXP
74LVC2373AD
Octal D-type transparent latch with 5-volt tolerant inputs/outputs; damping resistor 3-State
NXP
©2020 ICPDF网 联系我们和版权申明