BT148W-500R [NXP]
Thyristors logic level; 晶闸管逻辑电平型号: | BT148W-500R |
厂家: | NXP |
描述: | Thyristors logic level |
文件: | 总7页 (文件大小:57K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
GENERAL DESCRIPTION
QUICK REFERENCE DATA
Glass passivated, sensitive gate
SYMBOL PARAMETER
MAX. MAX. MAX. UNIT
thyristors in
a
plastic envelope
suitable for surface mounting,
intended for use in general purpose
switching and phase control
applications. These devices are
intended to be interfaced directly to
microcontrollers, logic integrated
circuits and other low power gate
trigger circuits.
BT148W- 400R 500R 600R
VDRM
VRRM
IT(AV)
,
Repetitive peak off-state
400
500
600
V
voltages
Average on-state current
RMS on-state current
Non-repetitive peak on-state
current
0.6
1
10
0.6
1
10
0.6
1
10
A
A
A
IT(RMS)
ITSM
PINNING - SOT223
PIN CONFIGURATION
SYMBOL
PIN
1
DESCRIPTION
cathode
4
a
k
2
anode
gate
3
g
2
3
1
tab anode
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
-400R -500R -600R
VDRM, VRRM Repetitive peak off-state
voltages
-
4001 5001 6001
V
IT(AV)
IT(RMS)
ITSM
Average on-state current half sine wave; Tsp ≤ 112 ˚C
-
-
0.6
1
A
A
RMS on-state current
Non-repetitive peak
on-state current
all conduction angles
half sine wave; Tj = 25 ˚C prior to
surge
t = 10 ms
-
-
-
-
10
11
0.5
50
A
A
t = 8.3 ms
t = 10 ms
ITM = 4 A; IG = 200 mA;
dIG/dt = 200 mA/µs
I2t
dIT/dt
I2t for fusing
Repetitive rate of rise of
on-state current after
triggering
A2s
A/µs
IGM
Peak gate current
Peak gate voltage
Peak reverse gate voltage
Peak gate power
Average gate power
Storage temperature
Operating junction
temperature
-
1
5
5
1.2
0.12
150
1252
A
V
V
W
W
˚C
˚C
VGM
VRGM
PGM
PG(AV)
Tstg
-
-
-
-
over any 20 ms period
-40
-
Tj
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the thyristor may
switch to the on-state. The rate of rise of current should not exceed 15 A/µs.
2 Note: Operation above 110˚C may require the use of a gate to cathode resistor of 1kΩ or less.
October 1997
1
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
THERMAL RESISTANCES
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Rth j-sp
Thermal resistance
junction to solder point
Thermal resistance
junction to ambient
-
-
15
K/W
Rth j-a
pcb mounted, minimum footprint
pcb mounted, pad area as in fig:14
-
-
156
70
-
-
K/W
K/W
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
IGT
IL
Gate trigger current
Latching current
Holding current
VD = 12 V; IT = 0.1 A
VD = 12 V; IGT = 0.1 A
VD = 12 V; IGT = 0.1 A
IT = 2 A
-
50
0.17
0.10
1.3
200
10
6
µA
mA
mA
V
-
IH
-
-
-
VT
VGT
On-state voltage
Gate trigger voltage
1.5
1.5
-
VD = 12 V; IT = 0.1 A
VR = VRRM(max); IT = 0.1 A; Tj = 110 ˚C
0.4
V
0.1
-
0.2
0.1
V
mA
ID, IR
Off-state leakage current VD = VDRM(max); VR = VRRM(max); Tj = 125 ˚C
0.5
DYNAMIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
dVD/dt
Critical rate of rise of
off-state voltage
Gate controlled turn-on
time
Circuit commutated
turn-off time
VDM = 67% VDRM(max); Tj = 125 ˚C;
exponential waveform; RGK = 100 Ω
ITM = 4 A; VD = VDRM(max); IG = 5 mA;
dIG/dt = 0.2 A/µs
VD = 67% VDRM(max); Tj = 125 ˚C; ITM = 2 A;
VR = 35 V; dITM/dt = 30 A/µs;
dVD/dt = 2 V/µs; RGK = 1 kΩ
-
-
-
50
-
-
-
V/µs
tgt
tq
2
µs
100
µs
October 1997
2
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
ITSM / A
Ptot / W
1
Tsp(max) / C
a = 1.57
12
10
8
110
conduction form
I
angle
degrees
factor
a
TSM
I
T
30
60
90
120
180
4
0.8
0.6
0.4
0.2
0
113
116
2.8
2.2
1.9
1.57
time
Tj initial = 25 C max
T
1.9
2.2
2.8
6
4
119
122
125
4
2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
1
10
100
1000
IF(AV) / A
Number of cycles at 50Hz
Fig.1. Maximum on-state dissipation, Ptot, versus
average on-state current, IT(AV), where
Fig.4. Maximum permissible non-repetitive peak
on-state current ITSM, versus number of cycles, for
sinusoidal currents, f = 50 Hz.
a = form factor = IT(RMS)/ IT(AV)
.
IT(RMS) / A
ITSM / A
2
1.5
1
1000
100
10
I
TSM
time
I
T
0.5
0
T
Tj initial = 25 C max
1
10ms
10us
100us
1ms
0.01
0.1
1
10
T / s
surge duration / s
Fig.2. Maximum permissible non-repetitive peak
on-state current ITSM, versus pulse width tp, for
sinusoidal currents, tp ≤ 10ms.
Fig.5. Maximum permissible repetitive rms on-state
current IT(RMS), versus surge duration, for sinusoidal
currents, f = 50 Hz; Tsp ≤ 112˚C.
VGT(Tj)
IT(RMS) / A
1.2
1
VGT(25 C)
1.6
1.4
1.2
1
112 C
0.8
0.6
0.4
0.2
0
0.8
0.6
0.4
-50
0
50
Tsp / C
100
150
-50
0
50
100
150
Tj / C
Fig.3. Maximum permissible rms current IT(RMS)
versus solder point temperature Tsp.
,
Fig.6. Normalised gate trigger voltage
VGT(Tj)/ VGT(25˚C), versus junction temperature Tj.
October 1997
3
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
IGT(Tj)
IGT(25 C)
IT / A
5
4
3
2
1
0
Tj = 125 C
Tj = 25 C
3
2.5
2
Vo = 1.107 V
Rs = 0.14 Ohms
1.5
1
max
typ
0.5
0
0
0.5
1
1.5
2
2.5
-50
0
50
Tj / C
100
150
VT / V
Fig.7. Normalised gate trigger current
IGT(Tj)/ IGT(25˚C), versus junction temperature Tj.
Fig.10. Typical and maximum on-state characteristic.
IL(Tj)
IL(25 C)
Zth j-sp (K/W)
100
10
3
2.5
2
1
1.5
1
t
P
D
p
0.1
0.01
t
0.5
0
10us
0.1ms
1ms
10ms
tp / s
0.1s
1s
10s
-50
0
50
Tj / C
100
150
Fig.8. Normalised latching current IL(Tj)/ IL(25˚C),
versus junction temperature Tj.
Fig.11. Transient thermal impedance Zth j-sp, versus
pulse width tp.
IH(Tj)
IH(25 C)
dVD/dt (V/us)
1000
3
2.5
2
RGK = 100 ohms
100
1.5
1
10
0.5
0
1
-50
0
50
Tj / C
100
150
0
50
100
150
Tj / C
Fig.9. Normalised holding current IH(Tj)/ IH(25˚C),
versus junction temperature Tj.
Fig.12. Typical, critical rate of rise of off-state voltage,
dVD/dt versus junction temperature Tj.
October 1997
4
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
MOUNTING INSTRUCTIONS
Dimensions in mm.
3.8
min
1.5
min
2.3
6.3
1.5
min
(3x)
1.5
min
4.6
Fig.13. soldering pattern for surface mounting SOT223.
PRINTED CIRCUIT BOARD
Dimensions in mm.
36
18
60
4.5
4.6
9
10
7
15
50
Fig.14. PCB for thermal resistance and power rating for SOT223.
PCB: FR4 epoxy glass (1.6 mm thick), copper laminate (35 µm thick).
October 1997
5
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
MECHANICAL DATA
Dimensions in mm
Net Mass: 0.11 g
6.7
6.3
B
3.1
2.9
0.32
0.24
0.2
M
A
A
4
0.10
0.02
7.3
6.7
3.7
3.3
16
max
13
2
3
1
10
max
1.05
0.85
0.80
0.60
2.3
1.8
max
M
0.1
(4x)
B
4.6
Fig.15. SOT223 surface mounting package.
Notes
1. For further information, refer to Philips publication SC18 " SMD Footprint Design and Soldering Guidelines".
Order code: 9397 750 00505.
2. Epoxy meets UL94 V0 at 1/8".
October 1997
6
Rev 1.300
Philips Semiconductors
Product specification
Thyristors
logic level
BT148W series
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1997
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
October 1997
7
Rev 1.300
相关型号:
©2020 ICPDF网 联系我们和版权申明